GVM 800D-RGB (01) PDF Document

The main features of the GVM 800D-RGB include:

• Ultra Heat Dissipation

• Aviation Aluminum Alloy Shell

• High CRI of ≥97+

• Digital Display

• PWM Dimming

• Stepless Dimming Dial for Adjusting Brightness

• Stepless Dimming Dial for Adjusting Color Temperature

• Stepless Dimming Dial for Adjusting Saturation

• Multiple Control Modes

• Dual Power Solutions

• Convenient Light Setting and Stabilized System

The GVM 800D-RGB comes with the following accessories:

• Carry Bag

• Power Cable

• Power Adapter

• Soft Diffuser

• Packing Box

The parts of the GVM 800D-RGB are:

1. Lithium Battery Slot

2. Power Switch

3. Control Mode Button

4. Brightness Adjustment Knob

5. Color Temperature/ Saturation/ Hue Adjustment Knob

6. Display Window

7. U Bracket Adjusting Knob

8. Power Interface

9. Soft Diffuser

10. LED Beam

11. Light Stand Locking Knob

12. U Bracket

Step 1. Assemble the Panel on the light stand by rotating the screw clockwise and disassemble it by rotating counter-clockwise.

Step 2. Insert the soft diffuser from one side of the lightpanel and fix it by the fix button.

Loosen the U bracket adjusting knob, adjust the angle of the panel which you need, then tighten the U bracket adjusting knob.

Plug the power adapter / insert the battery. Turn on the Power Switch. The switch has positions for Battery, Off, and Adapter.

Brightness: Rotate the left knob to adjust from 1% to 100%.

Hue: Press the right knob to switch to HUE mode, and rotate from 0 to 360°.

Saturation: Press the right knob to switch to SAT mode, and rotate from 0 to 100%.

Color Temperature: Press the right knob to switch to CCT mode, and rotate the knob from 3200K~5600K.

The current control mode and lighting parameters are shown on the LCD Window.

Choose the Control Mode with the Mode Button:

Rotate Mode: Adjust the knob to control the light manually.

Master-Slave Mode: Press the Mode button to enter Master Mode. Press the Mode button again to enter Slave Mode. Press ▲ or ▼ to choose the channel. The Master light can control slave lights on the same channel via Infrared Radiation.

Align the light stand installation hole to the light stand, then rotate the light stand locking knob. You can choose the light stand installation direction according to your operating needs.

Step 1. Open the light.

Step 2. Click to install the APP.

Step 3. Register your account with your email and a password.

Step 4. Select the light or equipment you purchased (e.g., “RGB lanterns”).

Step 1. Click on the menu at the top right of the app screen.

Step 2. Click the Settings button.

Step 3. Click to switch WIFI.

Step 4. Connect to the GVM-LED WIFI connection. The password is: gvm_admin. (Note: passwords are all lowercase and the bar is underlined).

Step 5. After connecting, return to the operator menu where the light can be controlled to adjust color, temperature, brightness, and turn it on or off.

Step 1. Turn on one 800D-RGB light first (keep others off). Press the MODE button on the light to switch it to WIFI mode.

Step 2. Open the mobile app and click on the menu in the top left corner.

Step 3. Click the Settings button, then click to switch WIFI.

Step 4. Connect to the GVM-LED WIFI network. The password is: gvm_admin. (Note: passwords are all lowercase and the bar is underlined).

Step 5. Go back to the mobile APP menu and click Switch Device to confirm that the single light can be controlled with the app.

Step 6. Now, turn on the other lights you wish to control. On each of these lights, press the MODE button to switch to Slave mode and set them to the same channel (CH-channel).

Step 7. In the app, select the “RGB lights” button to control the multiple lights together.

Note: To reset the factory WIFI name and password on a light, press and long hold the WIFI RESET/MODE button for about 5 seconds.

Step 1. In the app’s settings menu, click on “Modify WIFI”.

Step 2. In the “Modify WIFI” screen, enter the new WIFI name (example: GVM-100) and the new password (example: 123456789).

Step 3. Click “Confirm”. You will then need to return to your device’s WIFI settings to reconnect using the newly modified WIFI name and password.

Note: The Barn-door and soft filter are sold separately.

1. Barn-door Installation: To control the light angle, mount the barn-door by aligning its mounting holes to the light panel’s screw holes, and then use the screws to lock the barn-door in place.

2. Soft Diffuser Installation: To make the light softer, mount the enhanced soft diffusion. First, mount the diffusion support frame to the light panel, then align the diffusion to the screw holes and use the screws to lock the diffusion.

1. Do not look at the light directly when it is on.

2. Do not cover the light when it is on, or it will prevent the light from cooling down and damage it.

3. Do not place the light around flammable items such as alcohol, gasoline or near volatile solvent.

4. Do not place any liquid on the light or let it fall into the light.

5. Please take out the batteries if you don’t use them, to avoid battery leakage and fire.

6. Move the light carefully to prevent dropping it down.