GOODBABY SM35PTZ (01) PDF Document

Please make sure you have the following in the packing:

1. Parent unit x 1

2. Baby unit x 1

3. Adapter x 2

4. User manual x 1

5. Screw set x 1

Warning-Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of children (more than 3 ft/0.9m away). Do not remove the tag that is affixed to the cord of the unit.

Placement: Parent unit and baby unit with power cords should never be hung on or near the crib. This product is not a toy and should be kept out of children’s reach. This product contains small parts. Be careful when unpacking and assembling the product.

Read and keep instructions: All safety and operating instructions should be read before the video baby monitor is operated.

Adult Supervision: This product cannot replace responsible adult supervision.

Water and moisture: This product is designed for indoor use only. The unit should not be exposed to rain, moisture, dripping or splashing. No objects filled with liquid should be placed on top of, or beside the product, such as a glass or vase. This item should not be used near water.

DO NOT: Use the appliance if the cord or plug is damaged. If your baby monitor is not operating properly or has suffered any damage, contact the service center to request inspection and repair it in order to avoid any possible risk.

DO NOT: Attempt to repair or adjust any of the electrical or mechanical functions of the unit since, if you do, the guarantee will be made void.

Ventilation: This baby monitor should not be used on a bed, sofa, rug or similar surface that may block the ventilation openings, or be placed in an enclosed area, such as a bookcase or drawer that may impede air flow.

Heat Sources: This unit should not be exposed to direct heat sources such as a candle, replace, radiator, heat register, stove or other appliance that emits heat. The unit should not be left in direct sunlight.

Power source: This unit should only be used with the AC power adapters included in this package.

Signal: Shows the signal strength.

Alarm: An alarm has been set.

Lullaby: A lullaby is playing.

Baby Unit: Indicates which baby unit is currently selected or being viewed.

Volume: Shows the current volume level.

Brightness: Shows the current brightness level.

ECO: ECO mode is active.

Battery: Shows the battery level of the parent unit.

Zoom: The screen is in zoom mode.

Night vision: Infrared night vision is active.

Talk to baby: The talk-to-baby feature is currently in use.

Temperature: Shows the temperature in the baby’s room.

Step 1: Charge the Parent Unit.

Fully charge the Parent Unit before using it. When charging, the charging indicator will turn red. When the unit is turned on, the charging indicator will turn green.

Step 2: Turn On the Baby Unit.

Use the provided AC adapter to connect the Baby Unit to an AC outlet. The baby unit needs to be connected to the AC Adapter when using.

Step 3: Turn On the Parent Unit.

Press and hold the power button. The animation “Waiting for connection” will be displayed on the screen.

Step 4: Prepare for Connecting the Baby Unit.

Press the Menu key and choose the camera icon. Select a camera channel (e.g., 1), the icon will flash, then wait for the connection.

Step 5: Pair the Parent Unit with the Baby Unit.

Long press the “Pair” button at the back of the baby unit until the parent unit shows images. If it fails, choose another baby unit channel on the parent unit (2, 3, or 4) and try to pair again.

1. Press the Menu/Exit key, then the menu will display.

2. Press the Left button or RIGHT button until the Baby Unit icon is highlighted, then press the UP button or DOWN button to select the Baby Unit to pair.

3. Press the OK button to start pairing.

4. While the LED is flashing on the Parent Unit, press the PAIR button on the back of the Baby Unit.

5. Once paired, the screen will display the image from the Baby Unit.

6. If it fails, please repeat the steps above.

7. After connecting with all your Baby Units, press the OK key to view/scan the Baby Units. In Scan Mode, the scan icon will be displayed on the top of the screen.

1. Press and hold the zoom button for around 2 seconds to operate Zoom in/out.

2. In Zoom Mode, press and hold the Up/Down/Left/Right button to Pan/Tilt the image. In digital zoom mode, the zoom icon will be displayed on the top of the screen.

Note: If you want to adjust the volume/brightness, you have to exit the Zoom mode before operation.

To talk to your baby, press and hold the microphone icon button on the parent unit. Release the button when you have finished talking to listen to the sound from the baby’s room again. Bear in mind that you can’t listen to your baby whilst you’re talking to him/her. To listen to him/her, you have to stop pressing this button.

The infrared night vision function is automatic. It allows the camera to pick up images of your baby or the monitored area in dark or low light conditions. In this mode, only black and white images will be displayed on the monitor. The optimum image is from a 6 feet distance between the baby unit and the object.

This mode allows you to control the sound activation of your baby monitor. The ECO default setting is OFF. If there is no sound around the camera within 30 seconds, it will stop transmitting and the monitor screen turns off. When the camera detects a sound louder than the set sensitivity level, it will start transmitting the signal to the monitor again.

To change the ECO level:

1. Press the Menu/Exit key and the menu will pop up.

2. Press the LEFT key or RIGHT key until the ECO icon is highlighted.

3. Press the UP key or DOWN key to select the desired level.

4. Press the OK key to confirm.

Note: To view a video signal on your parent unit when ECO function is on, briefly press the power key.

ECO-LOW: Low sensitivity level, requiring a higher sound level to reactivate the transmission.

ECO-MID: Medium sensitivity level, requiring a medium sound level to reactivate the transmission.

ECO-HIGH: High sensitivity level, requiring a low sound level to reactivate the transmission.

OFF: Constant transmission – no standby mode.

You can use the alarm to remind yourself to feed baby/change diapers/sleep, etc.

1. Press the Menu/Exit key and the menu will pop up.

2. Press the LEFT key or RIGHT key until the alarm icon is highlighted.

3. Press the UP key to increment or press the DOWN key to decrement the time.

4. Press the OK key to confirm.

Note: If the alarm is ringing and no one answers, the ringing will last 1 minute and then stop. After 3 minutes, the ringing will start again. The ringing will sound up to three times total if no one answers.

You can soothe the baby to sleep by playing a gentle lullaby from the baby unit.

1. Press the Menu/Exit key and the menu will pop up.

2. Press the LEFT key or RIGHT key until the lullaby icon is highlighted.

3. Press the UP key or DOWN key to select a lullaby.

4. Press the OK key to confirm.

1. Press the shortcut key to enter into the Pan/Tilt mode.

2. Press the UP or DOWN key to Pan the Video.

3. Press the LEFT or RIGHT key to Tilt the video.

4. Press the shortcut key again to exit the Pan/Tilt mode.

Note: During the Pan/Tilt mode, you cannot use the navigation keys to adjust the Volume and the Brightness.

Clean the surfaces of the camera and monitor with a soft, fluff-free cloth. Never use cleaning agents or solvents. If the units become dirty, use a lightly dampened cloth to wipe surfaces, taking care to not allow water into any openings.

1. The power adapters may not be properly connected. Confirm that the camera and monitor are ON. Connect the baby unit correctly as per the “Getting Started” instructions.

2. The baby unit may be too far from the parent unit. Keep the distance between the baby unit and the parent unit within 900 feet (open space).

3. The baby unit and parent unit may not be properly paired. Follow the Pairing instructions.

4. If the above strategies do not work, restart the parent unit. At the back of the parent unit (under the stand) you will see a small black hole marked “Reset”. Just take a sharp object and press the reset button for a few seconds.

1. The baby unit may be too far from the parent unit. Keep the distance between the baby unit and parent unit within 900 feet (open space).

2. The baby unit or the parent may be placed too close to metal objects. Keep metal objects at least 5 feet away from the parent unit. In most cases, it is enough to move them about 8-10 inches away.

3. Other electronic devices may be interfering with the signal. Keep electronic devices at least 5 feet away from the parent unit. In most cases, it is enough to move them about 8-10 inches away.

4. The battery power may be too low. Fully charge the parent unit with the AC adapter provided.

5. If the above strategies do not work, restart the parent unit.

1. The baby unit and parent unit may be placed too close together. Keep a distance between the parent unit and the baby unit.

2. The volume on the parent unit may be set too high. Turn down the volume on the parent unit.

3. If the above strategies do not work, restart the parent unit.

1. The volume may be set too low. Turn up the volume on the parent unit.

2. If the above strategies do not work, restart the parent unit.

Restart the baby unit (unplug the adapter then plug it into the socket again). Press the reset key at the back of the parent unit (hidden behind the stand).

1. The temperature sensor is positioned very close to the baby unit and warms up during operation. Stretch out the sensor so it is far enough from the baby unit. Place the baby unit in an area with good air circulation.

2. If the above strategies do not work, restart the parent unit.

1. You may have paired the baby unit in the wrong way. Refer to the instructions for pairing more than one baby unit with the parent unit.

2. If the above strategies do not work, restart the parent unit.