GOGEN BPS 736 CD (01) PDF Document

To charge the internal battery, connect the supplied AC power cord to the AC socket on the back of the unit and plug it into a standard wall outlet. The charging process initiates automatically when the power cord is attached. During the charging process, the charge LED indicator will light up red. Once the battery is fully charged, the indicator will turn green.

The battery status is indicated by a specific LED light. A red light indicates that the unit is currently charging. A green light indicates that the battery is fully charged. If the LED indicator flashes in red, it means the battery is low and needs to be recharged.

After a full charge, the playback time for the unit is up to 22 hours when used at 50 percent volume levels.

It takes approximately 4 hours to fully charge the unit before using it for the first time.

No, users should not attempt to change the battery. Only high-qualified personnel are permitted to perform this operation.

To turn the unit on, press and hold the power button. To turn the unit off, press and hold the power button again.

Yes, the unit features an automatic standby mode. In CD, USB, Bluetooth, or AUX modes, if the unit does not provide a main function for approximately 15 minutes, it will automatically switch into standby mode. You can press the power button to turn the unit back on.

If the volume setting on your connected audio source is too low, the device may recognize it as no audio signal. This can affect the capability of signal detection and trigger an automatic switch into standby mode. To prevent this, increase the volume setting on the external audio source player.

If the unit resets or fails to operate normally due to electrostatic discharge, simply switch the unit off and then reconnect or switch it back on again to resume normal operation.

To cycle through the different function modes, press the FUNCTION button repeatedly. You can choose between CD, USB, BLUETOOTH, AUX, and RADIO functions.

Rotate the VOLUME knob located on the top panel of the unit to increase or decrease the overall music playback volume.

To change the volume for a connected microphone, press the MIC VOL.+ or MIC VOL.- buttons on the unit.

Press the BASS button on the unit to enhance the bass effect during audio playback.

The unit features a built-in equalizer system with five presets. Press the EQ button to select the setting that best matches your music style: FLAT, CLASSIC, ROCK, POP, or JAZZ.

The unit provides a dedicated 5V 1A USB charging port. Connect your smartphone’s USB cable to the port labeled USB CHARGE to begin charging your device. This port is intended for charging only and not for data transfer.

Press the ECHO button on the unit to turn the microphone echo effect on or off.

There are 5 flashing modes available for the DISCO LED lights. Press the LIGHT button to cycle through the modes, which are displayed as L-1 through L-5.

To turn off the DISCO LED lights, press the LIGHT button repeatedly until L-OFF is shown on the display. To turn off the button lights, projection light, and strobe light, press and hold the LIGHT button until E-OFF is displayed.

The projection light and strobe light are designed to flash to the beat of the music in all light modes. Additionally, the lights around the buttons will remain on in all light modes unless turned off using the E-OFF command.

First, press the FUNCTION button to select RADIO mode. The display will show FM and the current frequency. For the best reception, insert the supplied wired antenna into the FM socket on the rear cabinet and extend it to its full length.

In radio mode, press and hold the PAIR/SCAN button. The unit will scan for all available stations within reception range and save them to the preset memory automatically. Once finished, it will tune to preset number 1 (P-01).

To select the next or previous stored radio station, press the 10/M./FOLD.+ or 10/M./FOLD.- buttons.

Use the TUN.+ or TUN.- buttons to tune to a specific station. Press the buttons repeatedly for fine tuning or press and hold them to start an automatic search that stops when a strong signal is received.

Step 1. Tune to the desired station using the TUN.+ or TUN.- buttons.

Step 2. Press the PROG./P-MODE button. MEM and P-01 will flash on the display.

Step 3. If you wish to use a different preset number, use the 10/M./FOLD.+ or 10/M./FOLD.- buttons to change it.

Step 4. Press the PROG./P-MODE button again to finish saving the station. You can save up to 30 FM stations this way.

The system is compatible with digital audio CD and MP3 formats. This includes finalized digital audio CD-Recordable (CD-R) discs, finalized digital audio CD-Rewritable (CD-RW) discs, and standard CD-DA format discs.

Step 1. Press the FUNCTION button to select CD mode.

Step 2. Press the OPEN/CLOSE button to open the CD door.

Step 3. Place the disc into the tray with the printed label side facing up.

Step 4. Close the CD door. The display will show READING and then playback will begin from the first track.

Press the STOP button to ensure the disc is no longer spinning. Then press the OPEN/CLOSE button to open the CD door. Hold the disc by its edges and carefully lift it out of the tray.

During playback, press the PAIR/SCAN button to pause the track. The current track number and play time will flash on the display. To resume playback, press the PAIR/SCAN button again.

Press the TUN.+ or TUN.- buttons during play until the desired track number appears on the display. The unit will automatically start playing the selected track.

When playing an MP3 disc, you can skip forward or backward by 10 tracks by pressing the 10/M/FOLD.+ or 10/M/FOLD.- buttons.

While a track is playing, press and hold the TUN.+ or TUN.- buttons to scan through the track at high speed. Release the button when you reach the desired point to resume normal playback.

Programming must be done while the disc is stopped.

Step 1. Press the PROG./P-MODE button. The PROG logo will flash and show P-01.

Step 2. Use the TUN.+ or TUN.- buttons (or the 10/M/FOLD buttons) to select the first track you want to program.

Step 3. Press the PROG./P-MODE button to store the track. The display will show P-02.

Step 4. Repeat the selection process until all desired tracks are stored (up to 20 for standard CD or 99 for MP3).

Step 5. Press the PAIR/SCAN button to begin playing your programmed list.

To clear the program, you can press the STOP button twice while the disc is stopped or simply open the CD door. The program will also be erased if the unit is turned off.

You can choose between different repeat options by pressing the PROG./P-MODE button during playback:

Repeat Single: Press once to repeat the current track continuously (the repeat icon is shown).

Repeat All: Press until the ALL icon is shown to repeat all tracks on the disc or USB drive.

Repeat Folder: (For MP3 files with multiple folders) Press until the DIR icon is shown to repeat all tracks within the current folder.

Press the PROG./P-MODE button in play mode until RAN is shown steadily on the display. The unit will begin playing tracks in a random order automatically. To cancel, press the button again until RAN disappears.

Intro Play scans and plays the first 10 seconds of every track on the disc. Press the PROG./P-MODE button in play mode until INTRO is shown steadily on the display. To stop this and return to normal playback, press the button until INTRO disappears.

Step 1. Press the FUNCTION button to select USB mode.

Step 2. Insert your USB memory stick into the USB port on the top of the unit.

Step 3. The unit will automatically read the files and begin playback from the first track.

The main USB port is intended for data transfer and music playback only. External devices cannot be charged via this specific port (use the dedicated USB CHARGE port instead). Additionally, the use of USB extension cords is not recommended as they may cause interference or data loss.

Step 1. Press the FUNCTION button to switch to BLUETOOTH mode. The display will show BLUETOOTH and the pairing indicator will flash rapidly.

Step 2. Enable Bluetooth on your device (phone, tablet, etc.) and scan for available units.

Step 3. Select GoGEN HAPPEE from the list. If prompted for a password, enter 0000.

Step 4. Once paired, the indicator will stay lit and the display will show BLUETOOTH. You can now press play on your device.

The Bluetooth connection works best within a range of 10 meters in open air settings.

To disconnect the current Bluetooth connection, press and hold the PAIR/SCAN button on the unit.

Step 1. Press the FUNCTION button to select AUX mode.

Step 2. Connect your audio device to the 3.5mm AUX IN jack on the top panel of the unit using an AUX cable (not included).

Step 3. Control the music playback directly from your external audio device.

The microphone input is available in all function modes. Connect your microphone to the 6.3 mm MIC JACK on the top panel. You can then use the MIC VOL buttons to adjust the microphone volume independently of the music volume.

When handling discs, do not touch the reflective recorded surface. Never stick paper or write anything on either side of the disc. Additionally, do not bend the discs, as this can cause permanent damage and playback issues.

If a disc becomes soiled, wipe off dust, dirt, and fingerprints with a soft, dry cloth. Always wipe in a straight line from the center of the disc toward the outer edge. Never use chemicals such as benzene, thinners, or anti-static sprays.

Always store discs in their protective cases. Do not expose them to direct sunlight, high temperatures, high humidity, or dusty environments.

To keep the lens free from dust and contamination, always ensure the CD door is closed. You should never touch the lens directly.

The technical specifications are as follows:

No, you should not mount this product on a wall or a ceiling.

Before cleaning, always ensure the unit is unplugged from the electrical outlet. Clean the exterior using a dry cloth only. Do not use liquids or wet cloths as they could damage the electrical components.

Place the system on a flat, hard, and stable surface. Ensure there is good ventilation with at least 30 cm of clearance from the rear and top of the unit, and 5 cm from each side. Do not place the unit near objects that generate strong magnetic fields, such as televisions or other large speakers.

Ensure the unit is plugged into a 220-240 V 50 Hz power outlet. Never plug or unplug the power cord with wet hands. If you do not plan to use the system for a long time, remove the AC power plug from the wall outlet to disconnect it completely.

Yes, the unit supports MP3 discs with multiple folders. To select a desired folder during playback, press and hold the 10/M/FOLD.- or 10/M/FOLD.+ buttons to skip forward or backward by one folder at a time.

You should always press the buttons on the unit gently. Pressing them too hard can damage the internal switches and the control panel.

No, the apparatus should not be exposed to dripping or splashing liquids. It is intended for use in dry locations only. Do not place objects filled with liquids, such as vases, on top of the product.

The CD door is located on the front of the unit. You can open it by pressing the OPEN/CLOSE button on the top control panel while in CD mode.