GLADIATOR GAWUXXGFTG (01) PDF Document

You should be aware of the following safety definitions and warnings for the GLADIATOR GAWUXXGFTG:

DANGER: You can be killed or seriously injured if you don’t immediately follow instructions.

WARNING: You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

Important notes for installation:

1. Be sure the Gladiator GearWall panel or GearTrack channel is installed with mounting screws in every slot and at every stud location with a maximum of 24″ (60.96 cm) horizontally between screws.

2. Remove the caddies parts and fasteners, and dispose of/recycle all packaging materials.

1. Align the mounting brackets, one on each side of the rear frame, with the desired slots in the GearWall panel or GearTrack channel.

2. Engage the bracket rims into the slots in the GearWall panel or GearTrack channel by lifting up, pushing toward the wall and lowering the rims into the slots.

3. Inspect the ball caddy from the side to ensure the bracket rims are fully engaged in the slots.

IMPORTANT: Before assembling, first mount the ball caddy to GearWall panel or GearTrack channel.

1. Reach inside the ball caddy and unfasten the fabric closures running along the bottom front of the caddy.

2. Slide the hollow metal rods onto each end of the lower frame.

3. Holding the lower frame where it is joined with the metal rods, place the frame, bottom edge down, into the ball caddy at an angle.

4. Slide the hollow metal rods that are joined to the lower frame, onto each end of the upper frame.

5. Pull the lower frame forward until it is between the fabric closures at the bottom of the ball caddy. Fasten the fabric closures around both cross bars of the lower frame. NOTE: Make sure the fabric closures are fastened tightly around both the upper and lower crossbars of the frame.

6. Attach the eight hooks, one on each end of the four elastic straps, onto the upper and lower frame.

1. Using 5/16″ (7.93 mm) hex-head bolts (F1) and 5/16″ (7.93 mm) flange nuts (F2), attach the golf bag shelf to the sides.

2. Create a shoe shelf by using 5/16″ (7.93 mm) hex-head bolts (F1), to attach the 5 rods to both sides of the golf caddy.

3. Stand the golf caddy upright.

1. With the mounting bracket rims pointing down, align the 2 bracket holes with the top two holes in each side.

2. Working from the back, insert a carriage-head bolt (F7) through the holes in the bracket and into the side.

3. Working from the front, fasten each bolt with a washer (F8) and a flange nut (F2). Completely tighten the nuts.

4. Repeat steps 1 through 3 to attach the lower mounting bracket. NOTE: Hand tighten the nuts attaching the lower bracket. In order to mount the golf caddy on the wall, this bracket will need to be adjusted.

5. Using Phillips-head screws (F3b) and acorn nuts (F10), attach the golf bag divider to the 4 holes in the center of the upper mounting bracket.

IMPORTANT: If Gladiator GearTrack channels will be used to mount the golf caddy, they must be installed 18″ (46 cm) apart.

1. Determine caddy mounting location on GearWall panel or GearTrack channels.

2. Engage the upper mounting bracket into the wall slots by lifting up, pushing toward the wall and lowering the bracket rims into the slots.

3. Inspect the golf caddy from the side to ensure the upper mounting bracket rims are fully engaged in the slots.

4. Grasping the bolts, lift up on the lower mounting bracket to align the bracket rims with the slots on the GearWall panel or GearTrack channel.

5. Push the golf caddy toward the wall and lower the lower bracket rims into the slots. NOTE: Make sure the lower mounting bracket is fully engaged in the slots.

6. Using a 1/2″ (1.27 cm) wrench, tighten the nuts on the lower mounting bracket.

7. Inspect the golf caddy from the sides to ensure both the upper and lower mounting brackets are fully engaged in their respective slots.

8. Attach each strap to the side panel and to the D-ring on the golf bag divider.

1. Insert the threaded studs at the top of each side piece into the two holes in each side of the caddy back. NOTE: Make sure the bracket rim on the caddy back is to the outside of the side pieces.

2. Using two acorn nuts (F10) per side, attach the sides to the back. Completely tighten with a 3/8″ (9.52 mm) nut driver.

3. Attach the caddy shelf (with the name badge facing up) by interlocking the shelf tabs with the tabs on the back. NOTE: Make sure the lower mounting bracket is fully engaged in the slots.

4. Using the two Phillips-head screws (F3b) and two acorn nuts (F10) fasten the caddy shelf to the sides.

5. Holding each screw in place with a screwdriver, completely tighten the acorn nut with the nut driver.

1. Engage the bracket rims located on the back of the caddy into the slots in the GearWall panel or GearTrack channel by lifting up, pushing toward the wall and lowering the rims into the slots.

2. Inspect the caddy from the side to ensure the bracket rims are fully engaged in the slots.