GLADIATOR GAGB28FDYG (01) PDF MANUAL

GLADIATOR GAGB28FDYG (01) PDF SUMMARY:

What are some important safety messages?

Your safety and the safety of others are very important. Many important safety messages have been provided in this manual and on your appliance. Always read and obey all safety messages.

What is the safety alert symbol?

The safety alert symbol is an exclamation point inside of a triangle. This symbol alerts you to potential hazards that can kill or hurt you and others.

What do the words “DANGER” or “WARNING” mean?

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING”. “DANGER” means you can be killed or seriously injured if you don’t immediately follow instructions. “WARNING” means you can be killed or seriously injured if you don’t follow instructions.

What tools are needed to assemble this cabinet?

• 1/2" Wrench
• Phillips screwdriver
• 3/8" Wrench
• Pliers
• 11/32" Wrench
• Level

What tool is supplied?

• Hex key

What part is supplied?

• Key

How do you unpack the cabinet?

1. Remove and verify the contents as shown in “Tools and Parts.”
2. Dispose of/recycle all packaging materials.

How do you assemble the cabinet?

1. Place side panel (P1) on a flat, firm surface so that the edge with the holes is facing down.
2. Insert the cabinet top (P2) between the edges of side panel (P1). NOTE: Make sure the edges with the holes are facing down.
3. Align the holes and attach the top (P2) to side panel (P1) using hex head bolts (F1) and 5/16" flange nuts (F2). Do not tighten completely.
4. Position side panel (P3) so that the top (P2) is between the edges of side panel (P3).
5. Align the holes and attach the top (P2) to the side (P3) using six hex-head bolts (F1) and two 5/16" flange nuts (F2). Do not tighten completely.
6. Insert cabinet bottom (P4) between the edges of side panels (P1 and P3). NOTE: Make sure the edges with the holes are facing up.
7. Align the holes and attach the bottom (P4) to the side panels (P1 and P3) using six hex-head bolts (F1) and two 5/16" flange nuts (F2) for each side. Do not tighten completely.

What are some important tips when assembling the cabinet?

• Two people may be required to complete the assembly.
• As you assemble the cabinet, make sure the edges with the holes are facing up.
• If you are assembling the cabinet on the floor, fasten the eight front corner bolts, two at each corner, after you stand the cabinet upright.

What is the warning for excessive weight hazard?

Use two or more people to move, assemble or install cabinet. Failure to do so can result in back or other injury.

How do you attach the back panel?

1. Align lower back panel (P6) with the holes in the cabinet bottom (P4). Using phillips-head screws (F3), attach back panel (P6) to the bottom (P4) and sides (P1 and P3). Do not tighten screws completely.
2. Align upper back panel (P5) with the holes in the cabinet top (P2). Using phillips-head screws (F3), attach back panel (P5) to the top (P2) and sides (P1 and P3). Do not tighten screws completely. NOTE: Upper back panel (P5) will slightly overlap lower back panel (P6).
3. Using phillips-head screws (F3), attach the upper back panel (P5) to the lower back panel (P6).
4. Completely tighten all back panel screws starting with the sides and continuing with the top, middle, and bottom.
5. Using the hex key (provided), completely tighten all the cabinet bolts and nuts.

How do you install the leveling feet or casters?

The Gladiator® Modular GearBox is designed to be either stationary or to roll on casters. The casters are not included. To order the Gladiator® Steel Modular Gearbox caster kit see “Accessories”. The installation instructions to mount the casters are included with the caster kit. To install leveling feet:

1. Place the cabinet on its side.
2. Screw a leveling foot (P7) into each of the four rivet nuts located at the corners of the cabinet.
3. Stand the cabinet upright.
4. If you have not already, fasten the two bolts at each front corner of the cabinet frame. Completely tighten all the cabinet bolts and nuts.

How do you install the doors?

The door hinges are designed with keyhole slots at the top and bottom so the door will hang on the cabinet while you are fastening the screws.

1. Start Phillips-head screws (F3) in both the top and bottom holes on each side of the cabinet.
2. Hang the right-hand side door (P10) from the top and bottom screws, and hand tighten.
3. Insert the middle two screws through the door hinge into the cabinet and hand tighten.
4. Repeat steps 2 and 3 to attach the left-hand door (P9).
5. Align the doors and completely tighten the screws.

How do you complete the assembly?

1. Make sure there is a bolt or screw in each hole of the cabinet frame.
2. Move the cabinet to its final location.
3. Place a level on the inside shelf, and if necessary, level the cabinet by adjusting the height of the leveling feet (P7). Turn to the left to raise or to the right to lower the leveling foot.
4. If the doors are not aligned, loosen all the screws attaching the door hinge to the cabinet. Adjust door to the desired height, and fully tighten the screws.

How do you install the shelves?

1. Align the holes in the shelf (P8m) with the pair of holes as shown.
2. Using two Phillips-head screws (F3) and two small flange nuts (F5) per side, fasten shelf (P8m) to the cabinet sides (P1 and P3).
3. Place shelf (P8) so that the holes in the ends are aligned with the desired set of holes in the cabinet sides (P1 and P3).
4. Using two Phillips-head screws (F3) and two small flange nuts (F5) per side, fasten the shelf to the cabinet sides (P1 and P3).

What are some important notes when installing the shelves?

• Install shelf (P8m) in the cabinet so that the long edge with magnets is facing the cabinet front.
• Use the pair of holes indicated to install shelf (P8m), so the doors will lock.
• Shelf (P8) may be installed using any of the other pairs of holes in the cabinet sides.

What is the weight capacity for the top shelf?

150 lbs. / 68 kg

What is the weight capacity for the bottom shelf?

150 lbs. / 68 kg

What is the weight capacity for the inside shelf?

55 lbs. / 24.9 kg

How do you order accessories?

To order accessories, call 1-866-342-4089 and ask for the accessory part number listed below or contact your authorized Gladiator® brand dealer. In Canada, call 1-800-807-6777.

What is the part number for the VersaTop™ Work Surface?

GAVT18SPSX

How can you get warranty information?

In the U.S.A. call 1-866-342-4089 or visit the website at http://www.gladiatorgarageworks.com In Canada call 1-800-807-6777 or visit the website at http://www.gladiatorgarageworks.ca