Free English GLADIATOR GABK301PRS (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD GLADIATOR GABK301PRS (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What tools and parts are required for the installation of the GLADIATOR GABK301PRS bracket kit?
To install the GLADIATOR GABK301PRS, you will need a 1/2 inch wrench.
The following parts are supplied with the kit:
| Part | Quantity |
| Mounting brackets | 3 |
| 1/4 inch x 1/2 inch Carriage bolts | 6 |
| Hex nuts | 6 |
| Washers | 6 |
What are the use requirements and weight limits for the GLADIATOR GABK301PRS mounting brackets?
The GLADIATOR GABK301PRS mounting brackets are intended for use with Welded-Steel Tall GearBox and GearLocker cabinets only.
These brackets are not designed to be installed on cabinet models: GATGB000LG0 and GATGBL00LG0.
The brackets are intended to be used for mounting on Gladiator GearWall panels or GearTrack channels.
The brackets will support a cabinet with a maximum weight limit of 300 lbs (136 kg).
What safety precautions should be followed when installing the GLADIATOR GABK301PRS?
Due to the excessive weight hazard, use two or more people to move and install the GLADIATOR GABK301PRS. Failure to do so can result in back or other injury.
Always read and obey all safety messages, including those marked with the safety alert symbol and the words DANGER or WARNING, which indicate potential hazards that can kill or seriously injure you or others.
How do I attach the top mounting bracket to the GLADIATOR GABK301PRS cabinet?
Step 1. With the rim of a mounting bracket pointing down, align the holes in the bracket with the top pair of slots in the back panel of the cabinet. There are three groups of four slots in the back panel; the brackets must be attached to the top pair of slots in each group.
Step 2. Working from the back, insert two carriage bolts through the bracket and back panel.
Step 3. Working from the cabinet interior, fasten each bolt with a washer and a hex nut.
Step 4. Slide the bracket to the very top of the slot and fully tighten the nuts.
How are the middle and bottom mounting brackets installed on the GLADIATOR GABK301PRS?
Step 1. With the rim of a mounting bracket pointing down, align the holes in the bracket with the top pair of slots located in the middle section of the back panel.
Step 2. Working from the back, insert two carriage bolts through the bracket and back panel.
Step 3. Working from the cabinet interior, fasten each bolt with a washer and a hex nut. Hand tighten only, as this bracket will need to be adjusted later when mounting the cabinet on the wall.
Step 4. Repeat the above steps to attach the bottom mounting bracket to the lower section of the back panel using the top pair of slots in that group. Hand tighten the nuts only.
What are the requirements for GearWall panels or GearTrack channels used with the GLADIATOR GABK301PRS?
Ensure the GearWall panels or GearTrack channels are installed with mounting screws in every slot and at every stud location with a maximum of 24 inches (60.96 cm) horizontally between screws.
If GearTrack channels are used to support the cabinet, they must be installed 18 inches (46 cm) apart.
How do I mount the GLADIATOR GABK301PRS cabinet to the wall panels or channels?
Note: The two nuts on the middle and bottom mounting brackets must be loose enough to allow the brackets to move in the slots on the cabinet.
Step 1. Close the cabinet doors.
Step 2. Determine the cabinet mounting location on the GearWall panels or GearTrack channels.
Step 3. Using two or more people, engage the top bracket into the slot by lifting up, pushing toward the wall, and lowering the bracket rim into the slot.
Step 4. Ensure the top bracket is fully engaged in the slot.
Step 5. Open the cabinet doors.
Step 6. From inside the cabinet, grasp the bolts in the middle bracket and adjust the bracket until it aligns with the slot in the panel or channel.
Step 7. Push the cabinet toward the wall and lower the middle mounting bracket into the slot.
Step 8. Ensure the middle bracket is fully engaged in the slot.
Step 9. Repeat the adjustment and engagement procedure for the bottom bracket.
Step 10. Using a 1/2 inch wrench, fully tighten the nuts attaching the middle and bottom mounting brackets.
CLICK HERE TO DOWNLOAD GLADIATOR GABK301PRS (01) PDF DOCUMENT