GE ZKST304NRH (01) PDF Document

The controls on your GE ZKST304NRH allow you to manage its functions. The main control panel includes the following:

Display: Shows the actual temperature inside the drawer. During temperature setting, it displays the set temperature. It can also show error codes or setting information.

POWER: Press this button to turn your GE ZKST304NRH on or off. When turning on, press and hold for 3 seconds.

SET: Press this button to set the temperature. To access the settings menu, press and hold this button for 3 seconds.

+ and -: These buttons are used to increase or decrease the temperature setting and to navigate through the settings menu.

To access and use the settings menu on your GE ZKST304NRH, follow these steps:

1. Press and hold the SET button for 3 seconds to enter the menu.

2. Use the + and – buttons to scroll through the available settings options.

3. Press the SET button to select a setting you wish to change.

4. Use the + and – buttons to adjust the selected setting.

5. Press the SET button again to confirm your change.

6. To exit the settings menu at any time, press the POWER button.

You can adjust several settings on your GE ZKST304NRH through the settings menu. The available settings and their options are as follows:

Sabbath Mode on your GE ZKST304NRH is designed for observing certain religious holidays. When enabled, the interior lights, display, and alarms are disabled to prevent them from turning on or off with the opening of the drawer. The compressor and fans will continue to run as normal.

To enable or disable Sabbath Mode on your GE ZKST304NRH:

1. Press and hold the SET button for 3 seconds to enter the settings menu.

2. Use the + or – buttons to scroll until “Sabbath Mode” is displayed.

3. Press SET to select it.

4. Use the + or – buttons to select “On” or “Off”.

5. Press SET to confirm your choice. The “Sabbath Mode” icon will illuminate on the display when the mode is active.

6. Press POWER to exit the menu.

Showroom Mode on your GE ZKST304NRH is intended for retail display purposes. When this mode is activated, the cooling system is turned off, but the interior lights and controls will continue to function. To activate or deactivate Showroom Mode on your GE ZKST304NRH, you must access the settings menu.

The Door Alarm feature on your GE ZKST304NRH is designed to alert you if the drawer is left open. If the drawer remains ajar for more than 3 minutes, an alarm will sound. The “Alarm” icon will also illuminate on the control display. To silence the alarm, simply close the drawer completely. You can disable this feature in the settings menu if you wish.

If there is a power failure or your GE ZKST304NRH is disconnected from power, the unit is designed to remember its settings. Once power is restored, your GE ZKST304NRH will automatically return to the last temperature and feature settings that were active before the power interruption.

To set the temperature of your GE ZKST304NRH storage drawer, you can choose from preset options or set a custom temperature. Follow these steps:

1. Press the SET button. The display will show the preset temperature modes.

2. Use the + and – buttons to scroll through the preset temperature settings (Produce, Citrus, Meat, Pantry) or select Custom.

3. If you choose a preset, press SET to confirm. The display will show the selected mode for 3 seconds and then revert to showing the actual drawer temperature.

4. If you select Custom, press SET. The set temperature will start to blink. Use the + and – buttons to adjust the temperature to your desired level. Press SET again to confirm your custom temperature. The display will show your custom temperature for 3 seconds and then revert to showing the actual drawer temperature.

Your GE ZKST304NRH comes with several preset temperature settings for optimal storage of different items:

Produce: 34°F (1°C)

Citrus: 40°F (4°C)

Meat: 32°F (0°C)

Pantry: 45°F (7°C)

You can select any of these presets through the temperature setting controls.

To set a custom temperature on your GE ZKST304NRH, follow these instructions:

1. Press the SET button to enter the temperature setting mode.

2. Use the + or – buttons to scroll to the “Custom” option.

3. Press the SET button to select “Custom”. The current set temperature will start to blink.

4. Use the + and – buttons to adjust the temperature. You can set a custom temperature anywhere between 32°F and 45°F (0°C to 7°C).

5. Press the SET button again to confirm and save your custom temperature setting.

To clean the exterior of your GE ZKST304NRH, follow these guidelines:

Stainless Steel Panels and Handles: Use a commercially available stainless steel cleaner. Always clean and polish in the direction of the grain. Do not use appliance wax, polish, bleach, or products containing chlorine on stainless steel, as this can damage the finish.

Control Panel: Wipe with a damp cloth. Dry thoroughly. Avoid using cleaning sprays, large amounts of soap and water, abrasive cleaners, or sharp objects on the panel as they can cause damage.

To clean the interior of your GE ZKST304NRH, use a mixture of mild soap and water or a solution of two tablespoons of baking soda to one quart of warm water. Rinse the surfaces thoroughly with clean water and wipe them dry to prevent odors. Avoid using cleaning waxes, concentrated detergents, bleaches, or cleaners containing petroleum on plastic parts. Ensure the control panel is kept dry.

To safely remove the drawer from your GE ZKST304NRH, for instance for cleaning purposes, please follow these steps:

1. Pull the drawer out to its fullest extension.

2. Locate the tabs on the inside of each drawer slide.

3. Push the tab on the right slide down while simultaneously pulling the tab on the left slide up.

4. While holding the tabs in these positions, pull the drawer forward and out until it is free from the slides and the cabinet.

To reinstall the drawer into your GE ZKST304NRH after removal, follow these instructions:

1. Pull the cabinet slides out to their fullest extension.

2. Carefully align the drawer slides with the cabinet slides.

3. Push the drawer in until it stops. You will hear a click as the drawer engages with the slides.

To remove and replace the door gasket on your GE ZKST304NRH, follow these steps:

1. Starting at a corner, pull the old gasket straight out from the channel it is seated in.

2. To install the new gasket, start at a corner and press the gasket into the channel. Work your way around the entire perimeter of the drawer opening, ensuring the gasket is fully seated in the channel.

When preparing your GE ZKST304NRH for a vacation, the steps depend on the length of your absence:

For short vacations: You can leave the unit operating normally.

For long vacations: If you will be away for a month or more, it is recommended to turn off your GE ZKST304NRH. Remove all contents, unplug the unit from the power outlet, clean the interior thoroughly with a baking soda solution, and leave the drawer open to prevent odors from forming.

To prepare your GE ZKST304NRH for moving, follow these steps:

1. Turn off the unit and unplug the power cord.

2. Remove all contents from the drawer.

3. Thoroughly clean and dry the interior.

4. Securely tape the drawer shut to prevent it from opening during transport.

5. Ensure the GE ZKST304NRH remains in an upright position during the move.

If your GE ZKST304NRH drawer is not operating, try the following troubleshooting steps:

• Ensure the power cord is firmly plugged into a live electrical outlet.

• Check the fuse or circuit breaker for your home and replace or reset it if necessary.

• Verify that the unit is not in Showroom Mode, as this mode disables the cooling system.

If you notice that your GE ZKST304NRH drawer feels warm, consider the following possibilities:

• For a new installation, it is normal for the compressor to run for extended periods as the unit cools down. Allow 24 hours for it to cool completely.

• The drawer may have been opened frequently or for a long period of time.

• Ensure the drawer is fully closed and not blocked by any items.

• Check that the temperature control is set correctly for the surrounding conditions.

Frost or ice inside your GE ZKST304NRH is often caused by the drawer being left open. Ensure the drawer is closing completely and is not being held ajar by any contents inside.

Moisture collection on your GE ZKST304NRH can be normal, especially in humid environments. If moisture is inside, it can also be a sign that the drawer has been left open. Check to ensure the drawer is fully closed. For moisture on the outside, this is typically a normal result of high ambient humidity.

Your new GE ZKST304NRH may make sounds that are different from your old appliance. These are normal operating sounds and may include:

• Humming: The high-efficiency compressor may make a humming sound.

• Whooshing: Air circulation from the fans is a normal sound.

• Clicking or Snapping: This can occur when the defrost control turns on and off.

• Gurgling: This is the sound of refrigerant flowing through the cooling coils.

If the interior light on your GE ZKST304NRH is not working, first check to see if the unit is in Sabbath Mode. Sabbath Mode disables the interior lights. To turn the lights back on, you will need to disable Sabbath Mode through the settings menu.

If your GE ZKST304NRH is vibrating or rattling, it may not be level. Check the leveling legs to ensure the unit is stable and properly leveled on the floor.

The “Alarm” icon on the display of your GE ZKST304NRH indicates that the door alarm has been activated. This typically happens when the drawer has been left open for more than 3 minutes. To resolve this, check for any items obstructing the drawer and ensure it is closed completely. The alarm and the icon should turn off once the drawer is properly shut.