GE MONOGRAM ZTD910 (02) PDF MANUAL

GE MONOGRAM ZTD910 (02) PDF SUMMARY:

What should I do if I receive a damaged warming drawer?

You should immediately contact your dealer or builder.

---

What is the installer responsible for?

Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty. See the Use & Care Guide for warranty information.

---

What is the warming drawer intended for?

Use this appliance only for its intended purpose.

---

What should I check with local utilities for?

Check with local utilities for electrical codes that apply in your area. Local codes vary. Installation electrical connections and grounding must comply with applicable codes. In the absence of local codes, the drawer should be installed in accordance with National Electrical Code ANSI/NFPA 70-1990 or latest edition.

---

What is required to prevent the warming drawer from tipping?

An anti-tip brace must be installed to prevent the drawer from tipping forward when opened and loaded. Failure to do so could result in personal injury.

---

What are the models of warming drawers available?

ZTD910 30" Wide model

ZKD910 27" Wide model

---

Where can the warming drawers be installed?

The warming drawers may be installed directly into a wall or wall oven cabinetry, or below a countertop.

---

What does the ZXD27B, ZXD30B kit provide?

This kit provides for the installation of a custom front panel on 27" and 30" black and white wide models.

---

What should I do with the original drawer front when using the ZXD27B, ZXD30B kit?

The original drawer front will be removed and discarded when this kit is used. The tubular handle can be reinstalled onto the custom panel with longer screws (not provided). Or, the original handle can be replaced with a custom handle of your choice. (Handle is not supplied.) Choose a custom handle to match or complement cabinetry hardware.

---

What does the JXPN2 warming drawer pan kit include?

This kit includes supports and one full size and one half size pan with lids. The pans fit 27" and 30" wide models.

---

What tools and materials are required for installation?

• Wood screws and adhesive or other hardware for installing runners or shelf to support warmer drawer.
• 2 x 4 or 2 x 2 lumber for runners
• 2 x 4 or 2 x 2 wood block for anti-tip security
• Saw
• Level
• Drill and 1/16" bit
• Phillips screwdriver

---

What are the requirements for runners?

Runners must be level, rigidly mounted and capable of supporting 150 pounds.

---

Where can the drawer be installed?

• The drawer may be installed below a countertop, a cooktop, a single or double oven and side by side using 2 drawers.

---

What is the minimum clearance required when installing below approved cooktops?

Allow 2" min. clearance from bottom of cooktop burner box to top of warming drawer cutout.

---

What is the minimum clearance required when installing below approved ovens?

Allow a 2" min. clearance between cutouts. Additional clearances may be required.

---

Where is the electrical power cord located and how long is it?

Electrical power cord is located on the right side of the warming oven and is 56" long.

---

Where should I locate the outlet?

Locate the outlet within reach of the 56" long power cord in an adjacent cabinet, within 42" of the right side or 16" from the left side of the cutout. A recessed receptacle can be installed on the right side of the cutout, 7" max. from the rear of cabinet.

---

What is important regarding grounding for personal safety?

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.

---

Should I use an extension cord or adapter plug?

Do not use an extension cord or adapter plug with this appliance. Follow National electrical codes or prevailing local codes and ordinances.

---

What are the electrical requirements for the warming drawer?

This warming drawer must be supplied with 120V, 60Hz, and connected to an individual, properly grounded branch circuit, and protected by a 15 or 20 amp circuit breaker or time delay fuse.

---

Where should a properly grounded 3-prong receptacle be located?

A properly grounded 3-prong receptacle should be located within reach of the drawers’ 56" long power cord. Locate the receptacle in an adjacent cabinet.

• within 42" of the right side or,
• within 16" of the left side or,
• A recessed receptacle may be located on the right side of the cutout, 7" from the back of the cabinet. In this location, the excess power cord should be coiled and taped to the right side of the unit.
• When two warming drawers are installed side to side, they can operate from the same receptacle.

---

What should the customer do if the wall receptacle is not properly grounded?

The customer should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded and has the correct polarity. Where a standard 2-prong wall receptacle is encountered, it is the personal responsibility and obligation of the customer to have it replaced with a properly grounded 3-prong wall receptacle.

---

Should I cut or remove the third prong from the power cord?

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

---

Should I use an extension cord?

DO NOT USE AN EXTENSION CORD.

---

What is the first step to install the warming drawer?

Place carton on a flat surface.

---

What is the second step to install the warming drawer?

Open one end of the carton and lift off the top piece.

---

What is the third step to install the warming drawer?

Lift the warmer up and out of the carton.

---

What should I do after removing the warmer from the carton?

• Remove all packing materials and tape.
• Locate package containing 4 wood screws and set aside.

---

What is provided in the parts package?

• 4 Wood Screws

---

What is the required depth for a warming drawer installed below a countertop?

23-1/2" min. from inside back to front of cabinet frame.

---

What is the required width for a warming drawer installed below a countertop?

• 25-1/2" for 27" wide models,
• 28-1/2" for 30" wide models.

---

What is the required height for a warming drawer installed below a countertop?

9-1/4".

---

What is the minimum height above the floor or toekick for a warming drawer installed below a countertop?

5" min. above floor or 1" above toekick.

---

When is 23-1/4" from floor to bottom of cutout recommended?

For under countertop installation.

---

What must be installed when installing the warming drawer below a cooktop?

A solid barrier and air gap between cooktop and warming drawer is required.

---

What is the minimum distance from the lowest point of the bottom of the cooktop burner box to the top of the cutout?

When installing the warming drawer below a cooktop, a solid barrier must be installed at least 1" from the lowest point of the bottom of cooktop burner box to the top of cutout.

---

What type of material should be used as a barrier when installing the warming drawer below a cooktop?

Use any solid material such as 1/4" thick plywood. Allow at least 1/4" air gap between the barrier and the top of the warming drawer.

---

What must be installed when installing the warming drawer below a cabinet drawer?

In this installation, a solid barrier should be installed above the warming drawer to block access.

---

What type of material should be used as a barrier when installing the warming drawer below a cabinet drawer?

Use any solid material such as 1/4" thick plywood. Allow at least 1/4" air gap between the barrier and the top of the warming drawer.

---

What is the minimum height above the floor or toekick for a warming drawer installed below a cabinet drawer?

Observe the 5" min. above the floor or 1" above the toekick minimum installation height.

---

What may be necessary to install in frameless cabinets?

If you are installing in frameless cabinets, it may be necessary to install 1/2" wide cleats to accept drawer mounting screws.

---

What is the minimum distance between two warming drawers installed side to side?

Install two warming drawers in separate cutouts. Allow 2" min. between cutouts.

---

What are the required rough opening dimensions for installing under a wall oven?

The rough opening for the drawer must be:

• Depth: 23-1/2" min. from inside back to front of cabinet frame.
• Width: 25-1/2" for 27" wide models, 28-1/2" for 30" wide models.
• Height: 9-1/4".
• Allow 2" min. between oven and drawer cutouts for clearance of overlaps.

---

What may be necessary to install in frameless cabinets?

If you are installing in frameless cabinets, it may be necessary to install 1/2" wide cleats to accept drawer mounting screws. See drawer for mounting screw locations.

---

What are the steps to install the warming drawer?

• Slide left corner of the drawer into the opening.
• Push power cord into the hole leading to the outlet location. Thread the cord through as drawer is being pushed back into the opening. Check to be sure power cord does not get trapped under the drawer.
• If the outlet is installed inside the opening, plug the cord into the outlet. In this location, the excess power cord length should be coiled and taped to the right side of the unit.
• Push the drawer back until the front flange is flush to the cabinet front.

---

What are the final steps to install the warming drawer?

• Open the drawer fully.
• Drill pilot holes through the holes in the overlaping frame, one on each corner.
• Drive wood screws provided into each corner.