GE ADHR22 (01) PDF MANUAL

GE ADHR22 (01) PDF SUMMARY:

How do you connect electricity to the dehumidifier?

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded. DO NOT use an adapter plug with this appliance. The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance. Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded. Where a 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. The dehumidifier should always be plugged into its own individual electrical outlet, which has a voltage rating matching the rating plate. This provides the best performance and also prevents overloading house wiring circuits, which could cause a fire hazard from overheated wires.

How do you unplug the dehumidifier?

Never unplug your dehumidifier by pulling on the power cord. Always grip plug firmly and pull straight out from the receptacle.

What should you do if the receptacle does not match the plug?

The receptacle must be changed out by a qualified electrician.

What should you do if the electric service cords become frayed or otherwise damaged?

Immediately replace all electric service cords that have become frayed or otherwise damaged. A damaged power supply cord must be replaced with a new power supply cord obtained from the manufacturer and not repaired. Do not use a cord that shows cracks or abrasion damage along its length or at either the plug or connector end.

What should you do with the refrigerants in the dehumidifier prior to product disposal?

All dehumidifiers contain refrigerants, which under federal law must be removed prior to product disposal. If you are getting rid of an old product with refrigerants, check with the company handling disposal about what to do.

Can this dehumidifier be used outdoors?

No. Do not use outdoors.

What applications is this dehumidifier intended for?

This dehumidifier is intended for indoor residential applications only. This dehumidifier should not be used for commercial or industrial applications.

What tools, equipment, and safety standards are required for contractors and technicians working with this dehumidifier?

These R410A Dehumidifier Systems require contractors and technicians to use tools, equipment and safety standards approved for use with this refrigerant. DO NOT use equipment certified for R22 refrigerant only.

Can a person with reduced physical, sensory, or mental capabilities use this appliance?

Yes. This appliance can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

What is the risk of using extension cords with this dehumidifier?

Risk of fire. Could cause serious injury or death.

What is the function of the Power Pad?

Press to turn the dehumidifier on and off.

Does turning off the power by pressing the Power button disconnect the appliance from power supply?

No. Turning off the power by pressing the Power button does NOT disconnect the appliance from power supply.

What is the function of the Fan Speed Pad?

Controls the fan speed. Press to select either High, Medium, Low, or Smart Dry fan speed.

What are the fan speed options?

• High
• Medium
• Low
• Smart Dry

What is the function of the High fan speed setting?

Set the fan control to High for maximum moisture removal.

When should you set the fan control to Medium or Low?

When the humidity has been reduced and quiet operation is preferred, set the fan control to Medium or Low.

What does the Smart Dry fan speed do?

Smart Dry compares the set humidity level with the actual humidity and adjusts the fan speed automatically.

What does the Display show?

Shows the set % humidity level while setting, then shows the actual (+/– 5% accuracy) room % humidity level.

What is the function of the Humidity Set Control Pads?

The humidity level can be set within a range of 35% RH (Relative Humidity) to 80% RH (Relative Humidity) in 5% increments or in Nonstop mode for continuous operation. To set the unit for continuous operation, press the pad until the “Nonstop” indicator light is illuminated.

How will the dehumidifier operate when Nonstop is selected?

If Nonstop is selected, the dehumidifier will operate continuously at its maximum dehumidification settings if attached to a hose to drain or until the bucket is full.

How do you set the dehumidifier for drier air?

Press the pad and set to a lower percent value (%).

How do you set the dehumidifier for damper air?

Press the pad and set to a higher percent value (%).

What should you set the humidity control to when you first use the dehumidifier?

When you first use the dehumidifier, set the humidity control to 45% or 50%.

How long should you allow the dehumidifier to achieve the humidity level?

Allow at least 24 hours for the dehumidifier to achieve the humidity level.

What should you do if you still have damper air than desired?

If you still have damper air than desired, set the humidity level to a lower setting or select Nonstop for maximum dehumidification.

What does the Filter Timer do?

After 250 hours of operation, the Clean the Filter indicator light will glow to remind you to clean the filter. Remove the filter and clean it. Press and hold Filter button for 3 seconds to reset the filter reminder.

What is the function of the Delay Off button?

While the dehumidifier is operating press the Delay button. Press the / buttons to select the number of hours you want the dehumidifier to continue to operate before turning Off.

What will the Display show after displaying the Delay Off time?

After displaying the time, the Display will revert to showing the current humidity after 5 seconds have passed.

How do you display the number of hours left on the delay?

Pressing the Delay button will display the number of hours left on the delay.

What is the function of the Delay On button?

While the dehumidifier is off press the Delay button. Press the / buttons to select the number of hours you want the dehumidifier to remain off before turning On.

What will the display show after the Delay On time is set?

The display will show the number of hours left until the dehumidifier turns on.

How do you cancel the Delay?

Press the Delay button once, the hours remaining on the Delay will appear on the display. Press the Delay button again and the Delay will be cancelled.

When will the Empty Indicator blink?

The “Empty” indicator will blink when the bucket is ready to be emptied, or when the bucket is removed and/or not replaced in the proper position.

How long will the alarm sound for if the bucket is full or missing?

If the bucket is full or missing, an alarm will sound for about 10 seconds to remind you to empty and replace the bucket.

When will the Water Level Control Switch shut off the dehumidifier?

The Water Level Control Switch shuts off the dehumidifier when the bucket is full, or when the bucket is removed and/or not replaced in the proper position.

What will happen to the fan and compressor as soon as the bucket is removed?

The fan and compressor will stop running as soon as the bucket is removed.

When will the alarm sound in relation to the bucket?

The alarm will sound if the bucket is not replaced in the proper position after 3 minutes.

When will the compressor cycle off and the fan continue to run?

When frost builds up on the evaporator coils, the compressor will cycle off and the fan will continue to run until the frost disappears.

What will happen when the coil is defrosted?

When the coil is defrosted, the compressor or fan will automatically restart and dehumidifying will resume.

How long should you operate the dehumidifier continuously when first using it?

When first using the dehumidifier, operate the unit continuously for 24 hours.

What will happen in the case of a power outage or interruption?

In the case of a power outage or interruption, the unit will automatically restart, in the settings last used, after the power is restored.

How do you install the casters for 22 and 35 pint models?

1. Remove the 4 casters from the bag taped to the inside of the water bucket lid.
2. Carefully lay the dehumidifier down on it’s front or back.
3. Following the arrows on the base, slide the 4 casters into place.
4. Place the unit upright and wait 1 hour before use.

Where should you choose to locate the dehumidifier?

• Do not use outdoors.
• This dehumidifier is intended for indoor residential applications only. This dehumidifier should not be used for commercial or industrial applications.
• Place the dehumidifier on a smooth, level floor strong enough to support the unit with a full bucket of water.
• Allow at least 18 inches of air space on all sides of the unit for good air circulation.
• Place the dehumidifier in an area where the temperature will not fall below 41°F (5°C) or above 90°F (32°C). The coils can become covered with frost at temperatures below 41°F, which may reduce performance.
• The suggested range of relative humidity is between 40% and 50%
• Use the dehumidifier in cooking, laundry and dishwashing areas that have excessive moisture. NOTE: Place the dehumidifier away from the clothes dryer.
• Use the dehumidifier to prevent moisture damage anywhere books or valuables are stored.
• Use the dehumidifier in a basement to help prevent moisture damage.
• The dehumidifier must be operated in an enclosed area to be most effective.
• Close all doors, windows and other outside openings to the room.

Will a dehumidifier operating in a basement have an effect on an adjacent enclosed storage area?

A dehumidifier operating in a basement will have little or no effect in drying an adjacent enclosed storage area, such as a closet, unless there is adequate circulation of air in and out of the area.

What surfaces can the dehumidifier be rolled on?

The dehumidifier has casters to aid placement, but it should only be rolled on smooth, flat surfaces. Do not attempt to roll the dehumidifier on carpet or over objects.

How does the dehumidifier operate?

Moist, humid air is drawn over a cold refrigerated dehumidifying coil. Moisture in the air condenses on this coil and drains into a bucket (or through a hose and drain). Dry, clean air is drawn through the condenser where it is heated and discharged out the top grille into the room. It is normal for the surrounding air to become slightly warmer as the dehumidifier operates.

What should you always make sure of when removing collected water?

Always make sure the water bucket is locked into place on the dehumidifier.

When will the dehumidifier turn off automatically?

The dehumidifier will turn off automatically when the bucket is full, or when the bucket is removed or not replaced in the proper position.

Where must the bucket be placed for the dehumidifier to work?

The bucket must be replaced in the proper position for the dehumidifier to work.

What will happen if the bucket is not in the proper position?

The empty indicator will blink and the dehumidifier will not run if the bucket is not in the proper position.

Can you remove the foam piece and magnet block in the bucket assembly?

DO NOT remove the foam piece and magnet block in the bucket assembly. If removed the Dehumidifier will not work properly.

What are the 2 ways to remove collected water?

• Use the bucket. When the bucket is removed, the unit will shut off. Empty and replace the bucket.
• Use a hose. Water can be automatically emptied into a floor drain by attaching a garden water hose (not included).

Can you use the hose if using the bucket to collect water?

IMPORTANT: Do not use the hose if using the bucket to collect water. When the hose is connected, water will flow through it onto the floor instead of into the bucket.

When should you not remove the bucket?

• Do not remove the bucket while the dehumidifier is operating or if it has just stopped operating. This might cause some water to drip from the drain pan.
• The bucket must be in place and securely seated for the dehumidifier to operate.

How do you use a hose to remove collected water?

1. Remove the bucket from the front of the unit.
2. Open the drain cover on the side of the unit.
3. Thread a garden hose (not supplied) onto the nozzle and ensure it is seated securely. Cut to length and lead it to the floor drain.
4. Replace the bucket in the unit.

Where must the bucket be for the dehumidifier to operate when using a hose to remove collected water?

The bucket must be in place and securely seated for the dehumidifier to operate. The drain hose must run down from the dehumidifier to the floor drain.

When should the air filter be checked and cleaned?

The air filter behind the rear grille should be checked and cleaned at least every 250 hours of operation or more often if necessary.

When will the Filter indicator light glow?

After 250 hours of operation, the Filter indicator light will glow to remind you to clean the filter.

How do you clean the air filter?

Remove the filter and clean it. Replace the filter and press and hold the filter button for 3 seconds.

How do you remove the air filter?

Remove the rear grille and the filter will be attached.

How do you clean the air filter?

Clean the filter with warm, soapy water. Rinse and let the filter dry before replacing it.

Can you put the air filter in an automatic dishwasher?

NOTE: DO NOT put the filter in an automatic dishwasher.

Can you operate the dehumidifier without a filter?

CAUTION DO NOT operate the dehumidifier without a filter because dirt and lint will clog the unit and reduce performance.

How do you clean the case?

Use water and a mild detergent. Do not use bleach or abrasives.

How do you clean the rear grille?

Use a vacuum attachment or brush.

How often should you clean the water bucket?

Every few weeks, clean the bucket to prevent growth of mold, mildew and bacteria.

How do you clean the water bucket?

Partially fill the bucket with clean water and add a little mild detergent. Swish it around in the bucket, empty and rinse.

Can you clean the water bucket in a dishwasher?

NOTE: Do not use a dishwasher to clean the water bucket.

How do you remove the water bucket?

Remove the bucket and pour out any water.

How do you replace the water bucket?

Slide the bucket into the dehumidifier.

Where must the bucket be placed for the dehumidifier to operate?

NOTE: The bucket must be in place and securely seated for the dehumidifier to operate.

What should you do before cleaning?

Turn off the dehumidifier and remove the plug from the wall outlet before cleaning.

What should you do if the dehumidifier does not start?

Problem	Possible Cause	What To Do
Dehumidifier does not start	The dehumidifier is unplugged.	Makes sure the dehumidifier’s plug is pushed completely into the outlet.
	The fuse is blown/circuit breaker is tripped.	Check the house fuse/circuit breaker box and replace the fuse or reset the breaker.
	Dehumidifier has reached its set humidity level or bucket is full.	The dehumidifier automatically turns off when either condition occurs. Change to a lower setting or empty the bucket and replace properly.
	Bucket is not in the proper position.	The bucket must be in place and securely seated for the dehumidifier to operate.
	Power Failure.	There is a protective time delay (up to 3 minutes) to prevent tripping of the compressor overload. For this reason, the unit may not start normal dehumidification for 3 minutes after it turned back on.

What should you do if the dehumidifier does not dry the air as it should?

Problem	Possible Cause	What To Do
Dehumidifier does not dry the air as it should	Did not allow enough time to remove the moisture.	When first installed, allow at least 24 hours to maintain the desired dryness.
	Airflow is restricted.	Make sure there are no curtains, blinds or furniture blocking the top or back of the dehumidifier. See the Choosing a Location section.
	Dirty Filter	See the Care and Cleaning section.
	The Humidity Control may not be set low enough.	For drier air, press the pad and set to a lower percent value (%) or at the Nonstop setting for maximum dehumidification.
	Doors and windows may not be closed tightly.	Check that all doors, windows and other openings are securely closed.
	Clothes dryer may be blowing moisture-laden air into the room.	Install the dehumidifier away from the dyer. The dryer should be vented to the outside.
	Room temperature is too low.	Moisture removal is best at higher room temperatures. Lower room temperatures will reduce the moisture removal rate. Models are designed to be operated at temperatures above 41°F (5°C).

What should you do if the dehumidifier runs too much?

Problem	Possible Cause	What To Do
Dehumidifier runs too much	Area to be dehumidified is too large.	The capacity of your dehumidifier may not be adequate.
	Doors and windows are open.	Close all doors and windows to the outside.
	Frost appears on the coils Room temperature is below 41°F
	Intended to use the bucket to collect water, but a hose was attached.	Disconnect the hose if using a bucket to collect water. See the Removing Collected Water section.
	Bucket Full LED light flashing and alarm sounds while drain hose is connected.	Check drain hose connection.
	Drain hose not tight on fitting.
	Drain hose is kinked.	Ensure the drain hose is pointed straight down to the floor and is not kinked in anyway.

What is excluded from the implied warranties?

Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law.

Who is the limited warranty extended to?

This limited warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA.

Who is responsible for a trip charge or bringing the product to an Authorized GE Appliances Service location if located in an area where service by a GE Appliances Authorized Servicer is not available?

You may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Appliances Service location for service.

What does the limited warranty exclude in Alaska?

In Alaska, the limited warranty excludes the cost of shipping or service calls to your home.

Who should you consult to know your legal rights?

To know what your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

What will be replaced for one year from the date of the original purchase?

Replacement, repair, or refund of the original retail price for any product which fails due to a defect in materials or workmanship.

What is the warranty on a replacement unit?

If the unit is exchanged, the replacement unit is warranted for the remainder of your product’s original one-year warranty period.

What will GE Appliances do if the product fails due to a defect in materials or workmanship?

GE Appliances will, at its sole discretion, replace the product with a product of the same or comparable functionality and quality or refund the original retail price.

What information is not covered by the warranty?

• Service trips to your home to teach you how to use the product.
• Improper installation.
• Failure of the product if it is abused, misused, or used for other than the intended purpose or used commercially.
• Replacement of house fuses or resetting of circuit breakers.
• Damage to the product caused by accident, fire, floods or acts of God.
• Incidental or consequential damage caused by possible defects with this dehumidifier.

When should you contact your dealer or installer?

If you require information regarding operating instructions and user controls, have an installation problem, or if the dehumidifier is of improper capacity, contact your dealer or installer.

Who is responsible for providing adequate electrical connecting facilities?

You are responsible for providing adequate electrical connecting facilities.

What will not be covered by the warranty?

Damage from or to the product resulting from improper maintenance or service performed by anyone other than a GE Appliances Authorized Servicer, use of non-genuine GE Appliances parts or external causes such as; abuse, misuse, inadequate power supply voltage, accident, fire, floods or acts of God.

How do you register your new appliance online?

You can register your new appliance online at your convenience!

What are the benefits of timely product registration?

Timely product registration will allow for enhanced communication and prompt service under the terms of your warranty, should the need arise.

How do you register your new appliance by mail?

You may also mail in the pre-printed registration card included in the packing material.

How do you purchase a GE Appliances extended warranty?

Purchase a GE Appliances extended warranty and learn about special discounts that are available while your warranty is still in effect. You can purchase it on-line anytime.

Will GE Appliances Services be there after your warranty expires?

Yes. GE Appliances Services will still be there after your warranty expires.

How can you order parts and accessories?

Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes (VISA, MasterCard and Discover cards are accepted). Order on-line today 24 hours every day.

What procedures do the instructions in this manual cover?

Instructions contained in this manual cover procedures to be performed by any user.

Who should perform other servicing?

Other servicing generally should be referred to qualified service personnel.

Why should caution be exercised when servicing?

Caution must be exercised, since improper servicing may cause unsafe operation.