FUTURE CALL FC-0613 (01) PDF Document

Before using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons including the following:

1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement or near a swimming pool.
5. Do not place this product on an unstable cart, stand, or table. The product may fall causing serious damage to the product.
6. Slots and openings in the enclosure and the back and bottom are provided for ventilation, to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation unless proper ventilation is provided.
7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by persons walking on it.
9. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
10. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.
11. Do not disassemble this product, but take it to a qualified service technician or service center when repair work is required. Opening or removing covers may expose you to voltage or other risks. Incorrect reassembly can cause electric shock when the appliance is subsequently used.
12. Unplug this product from the wall outlet and refer to qualified service personnel under the following conditions:

    A. When the power supply cord or plug is damaged or frayed.

    B. If liquid has been spilled into the product.

    C. If the product has been exposed to rain or water.

    D. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage and may require extensive work by a qualified technician to restore the product to normal operation.

    E. If the product has been dropped or the enclosure has been damaged.

    F. If the product exhibits a distinct change in performance.

13. Avoid using a telephone during an electrical storm. There may be a remote risk of electric shock from lightning.
14. Do not use the telephone to report a gas leak in the vicinity of a leak.
15. Never install telephone wiring during a lightning storm.
16. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
17. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

Coil Cord Connection

Insert coil cord into modular jack located on left hand side housing. Connect the other end into the modular jack located on handset.

Line Cord Connection

Insert the modular plug of the straight cord into the rear side of base unit, the insert the other end of RJ11C plug into the wall jack.

Your PHONE remembers the last number dialed. If the number you dial is busy or not being answered, hang up. To redial the last number automatically, press the REDIAL button.

NOTE: You can redial the same telephone number as many times as required. However, once you dial another number, the previous number is erased.

The REDIAL key is also used as a pause key when programming this phone on a PBX system. E.G… “9” before the number.

Your phone provides a ringer adjustment of High, Low and Off. When you don‘t want to be disturbed, slide the switch to the off position. Now you can still make outgoing calls without being disturbed by incoming calls.

The Handset Receiver Volume Switch (VHI / HI / MED) may be used to adjust the handset volume of received speech.

VHI = Very High – HI = High and MED = Normal

This switch is used to prevent storing of number by mistake. This switch needs to be ON to be able to store memory numbers.

This switch is used to switch between Normal and One touch dialing.

FLASH KEY: This key is for getting a new line if you make a mistake when dialing or it is also used to answer a call waiting call.

MUTE KEY: This key is used to mute the handset mic. When you are talking you need to hold it down when you want to mute the mic on the handset.

Your PHONE is equipped with 911 memory key and ten 2 touch memory keys (Pictures) for programming your most frequently dialed telephone numbers.

1. Make sure the store ON – OFF switch is ON.
2. Slide the Normal / One touch Switch to NORMAL position.
3. Lift the handset and place it on the side. Do not listen to the handset while programming.
4. Press and release STORE button. Note: Once you start programming a number do not hesitate.
5. Press the 0-9 keys for the telephone number you wish to store including area code if needed.
6. Press and release the STORE button again.
7. Press the (0-9) (pictures) where you want that telephone number stored in.
8. Your number is now stored.
9. Replace handset.
10. To change a stored number, repeat the same process. The new number will be stored and the old number will be removed.

If you need to disconnect the 911 key you may program any other number you wish or just the digit “1” into this key by following the points 1-6 (in the programming instructions), push the 911 key for point 7 then points 8-9.

To retrieve numbers stored in the key button, pick up the handset and press the MEMORY button. Then press the key button number (0-9) (pictures) which stores the telephone number you want to dial. Your call will be automatically dialed.

To retrieve numbers stored in the key button, Pick up the phone and wait for a dial tone, then press the key button (pictures) which stores the telephone number you want to dial. Your call will be automatically dialed.

Please note:

• Original Two touch memories will become one touch memories at ONE TOUCH mode.
• There will be no dialing (0-9) function when the ONE TOUCH mode is selected.
• You can not program any memories when in ONE TOUCH mode.

1. Remove numbered plastic cover from each key 0-9.
2. You will need a pictures approximately 0.9” x 0.9” inch.
3. Place picture into key.
4. Replace plastic cover.

Yes, this equipment is hearing aid compatible.