FUJIFILM DIGITAL PHOTO PRINTER II PSC2D (01) PDF Document

Plug the power cord into the power jack on the back of the FUJIFILM DIGITAL PHOTO PRINTER II PSC2D.

Press the power button to turn on the FUJIFILM DIGITAL PHOTO PRINTER II PSC2D. The power indicator lights up, and the printer’s Wi-Fi automatically enters the state of waiting for connection, with the indicator light constantly on orange.

Search for “FUJIFILM Print” in the application store or scan the provided QR code to download and install the FUJIFILM Print APP.

Step 1. Open the ribbon door.

Step 2. Insert a new ribbon and clamp it securely.

Step 3. Close the ribbon door.

Step 1. Pull out the paper tray.

Step 2. Open the paper tray door.

Step 3. Insert the paper tray into the machine.

Step 1. Take out the paper tray and open the paper tray cover.

Step 2. Place the photo paper in the paper tray with the glossy side facing up and the FUJIFILM logo face down. Note: The paper in the paper tray will not feed if more than 20 sheets of photo paper are loaded. Do not touch the area within the cutting lines of the paper.

Step 3. Close the paper tray cover.

Step 1. Open the ribbon door.

Step 2. Push the handle upward, the old ribbon will automatically pop out, and take out the old ribbon.

Step 3. Insert the new ribbon, make sure it is clamped securely, and then close the ribbon door.

When printing, the photo paper will move back and forth. Please ensure there is more than 10cm of space behind the FUJIFILM DIGITAL PHOTO PRINTER II PSC2D. Note: The paper will move in and out several times.

When the FUJIFILM DIGITAL PHOTO PRINTER II PSC2D is idle, the paper tray can be placed in the paper tray storage slot on the upper part of the printer to save space and prevent contamination and dust. The printer has a built-in lithium battery. Storage should avoid high temperature and high humidity environments. The battery should be charged at least once every 3 months. Use of the battery is forbidden after it has been immersed in water.

The button operations for the FUJIFILM DIGITAL PHOTO PRINTER II PSC2D are as follows:

Note: When successfully restoring factory settings, all indicators will turn on and blink for 2 seconds. When successfully resetting the network, the router connected to Wi-Fi indicator and the direct connection (Wi-Fi) indicator will turn on and blink for 2 seconds.

Printing will not be interrupted by pressing or pressing and holding the power button. Updating firmware will not be interrupted by pressing or pressing and holding the power button.

Press the power button to turn off the printer when an error occurs, and the printer will try to fix the error automatically once restarted. If it cannot be turned off, press the reset button with a needle to restart the printer.

The network can only be reset when the printer is standby.

The indicator lights on the FUJIFILM DIGITAL PHOTO PRINTER II PSC2D have the following meanings:

On/Off Indicator:

• Off: Turned off
• Orange Blinking: Error, please follow the APP instruction
• Orange On: Turned on
• White Blinking: Firmware upgrading
• White Blinking: Printing
• Breath: Sleeping

Battery Level Indicator:

• Off: Battery full
• Orange On: Battery low
• Orange Blinking: Out of power
• Constantly on: Charging
• White Blinking: Battery error, please contact for repair

Router Connected to Wi-Fi Indicator:

• Orange Off: Unconnected
• Orange Blinking: Connecting
• Blue On: Connected successfully

Direct Connection (Wi-Fi) Indicator:

• Orange Off: Function off
• Orange On: Function on
• Orange Blinking: Function starting
• Blue On: Connected with one or more

Open the FUJIFILM Print APP, navigate to Home page > Settings > Router mode settings > Input the router account and password of the required network connection > network connection > Select router from the list. Open the Wi-Fi settings of your photo stored device and select router Wi-Fi.

Note: For the first network connection, please turn on the Bluetooth of your phone. Due to APP upgrading and renewal or other reasons, the actual flow may be inconsistent with this user manual. Please follow the instruction in APP.

Turn on the Direct Connection (Wi-Fi) function. Press the Direct Connection (Wi-Fi) button on the back of the printer. Confirm that the Direct Connection (Wi-Fi) indicator is orange and constantly on; the direct connection (Wi-Fi) mode turns on. Open the Wi-Fi settings of the photo storage device, select “FUJIPSC2[XXXX]”, and direct connection (Wi-Fi) will be successfully established.

Note: The default connection password is 12345678, which can be changed in the APP. It can support simultaneous connection of up to 5 devices. The specific figures for [XXXX] are the last four digits of the product SN number, which can be found on the label at the bottom of the printer.

After connecting Wi-Fi through a router or direct connection (Wi-Fi), open the FUJIFILM Print APP. You can choose one of the printing modes: Fast printing / common printing (Photo editable mode) / certificate photo printing (automatic layout) / template printing.

After connecting Wi-Fi through a router or direct connection (Wi-Fi), open the album of the Android / Apple device, select the photos, and choose Print.

Note: If you cannot find the “Print” option in your Android device album, you can go to the specified link to download the corresponding APP and check how to use it.

Please download the driver from the product help page of the FUJIFILM official website and install it. Connect via a router connection or direct connection (Wi-Fi).

For Windows 7/8/8.1: Click Control panel > Hardware and sound > Device and printer > Add printer > select “Princiao Smart 2 [xxxx]-WiFi”.

For Windows 10: Click Settings > Device > Printer and scanner > Add printer or scanner > select “Princiao Smart 2 [xxxx]-WiFi”.

Note: Make sure the computer and printer are on the same Wi-Fi network. The specific figures for [XXXX] are the last four digits of the product SN number, which can be found on the label at the bottom of the printer.

The optimal printing temperature for the FUJIFILM DIGITAL PHOTO PRINTER II PSC2D is 10°C to 35°C, with a relative humidity of 40% to 60%. If the ambient temperature and humidity are not suitable, the printing quality may be affected.

DO NOT use any unofficial ribbon or photographic paper to ensure the printing quality of the FUJIFILM DIGITAL PHOTO PRINTER II PSC2D.

Avoid touching the glossy side of the photo paper to prevent fingerprints from affecting the printing quality.

When printing, make sure the glossy side of the photo paper is facing up, and the FUJIFILM logo side is facing down in the paper tray. Ensure the paper tray is installed correctly in the front position of the FUJIFILM DIGITAL PHOTO PRINTER II PSC2D.

The back output of the FUJIFILM DIGITAL PHOTO PRINTER II PSC2D should not be blocked, as this will block the paper path and affect printing quality.

During the printing process on the FUJIFILM DIGITAL PHOTO PRINTER II PSC2D, the photo paper needs to move back and forth in the printer four times. After printing is finished, it will be ejected automatically. Please be patient and do not pull out the paper by force to avoid damaging the printer.

The FUJIFILM DIGITAL PHOTO PRINTER II PSC2D uses dye-sublimation printing technology, and the print head is heated during printing. It may remain hot for a while even after printing is completed. To avoid getting burned, do not touch the print head.

Slight color differences between photos printed from different printers, photo paper, or ribbons are normal for the FUJIFILM DIGITAL PHOTO PRINTER II PSC2D.

When the FUJIFILM DIGITAL PHOTO PRINTER II PSC2D is left unused for a long time, it is recommended to remove the paper tray, close the paper tray door, and close the paper tray cover. Insert the paper tray into the printer tray storage slot to prevent dust from entering the printer. Otherwise, the quality of future prints could be negatively affected.

If unused photo paper is stored inside the FUJIFILM DIGITAL PHOTO PRINTER II PSC2D, you must avoid high temperature and humid environments.

The FUJIFILM DIGITAL PHOTO PRINTER II PSC2D has a built-in lithium battery. Storage should avoid high temperature and high humidity environments. If not connected to power, ensure the battery is charged at least once every 3 months. The battery is forbidden to use after being immersed in water.

DO NOT use any adapter other than the original one for the FUJIFILM DIGITAL PHOTO PRINTER II PSC2D, as this may cause printing failure.

DO NOT use the adapter of the FUJIFILM DIGITAL PHOTO PRINTER II PSC2D on other devices in case of any damage.

It is recommended to plug in the power adapter during upgrading on the FUJIFILM DIGITAL PHOTO PRINTER II PSC2D to avoid damage caused by accidental power loss due to low battery.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines, the FUJIFILM DIGITAL PHOTO PRINTER II PSC2D should be installed and operated with a minimum distance of 20cm between the radiator and your body. Use only the supplied antenna.