Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF


PDF Content Summary:

****** Page 1 ****** The Archer R6 has 6 high-precision PWM channel outputs bundled in a compact light-weight design. It supports full-range signal strength with dual detachable antennas to assure optimal antenna reception and maximum range. Features an inverted S Port that allows for easily connecting flight controllers, in addition to all this, the R6 can also be used as a redundancy receiver along with any other FrSky ACCESS capable receiver equipped with a SBUS port The best available signal will be used to ensure superior connectivi- ty All of the Archer receivers are hyper-matched with the ACCESS protocol. They not only feature wireless firmware upgrades, increased range, and telemetry performance, the R6 now supports more functions like configurable telemetry power, S.P01t/F .Port switching and FLR output Additional valuable features are under development to unlock the true potential of the ACCESS protocol. Instruction Manual for FrSky ARCHER R6 Receiver Introduction SBUS Out » SBUS In Version 1.0 Overview TOP Specifications Dimension: mm (L*W*H) Weight: 35g Number of Channels: 6/24 channels - 6 High-precision PWM & 16 SBCJS channels - 6 High-precision PWM & 24 configurable SBUS channels (Stay tuned) Operating Voltage Range: 35 -IOV Operating Current: <55mA@5V Operating Range: >2km (Full range) (*Range may vary based on local conditions.) Voltage Measurement Range via AIN2 (External device): 0-3.3V Compatibility: All FrSky ACCESS transmitters Optional Accessories. IPEX4 dipole copper antenna for 24GHz receivers —Size: 150mm Weight: 1.2g Link: BOT Features • ACCESS protocol with Over The Air (OTA) • Receiver redundancy • 6 high-precision PWM channels • SBUS IN & OUT (using standard servo connectors) • SP01t / FPort and AIN2 (on 4 pin socket) • VFR (Valid Frame Rate) telemet1Y antenna Slave No Telemetry LED state Green LED On Flash On On On FrSky Electronic Co., Ltd. Red LED On Flash On Off Off On Status Register Register successfully Bind Bind successfully Working normally Failsafe Contact us : Add: F-4,Building C, Zhongxiu Technolog Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Suppmt: 01140164

****** Page 2 ****** Instruction Manual for FrSky ARCHER R6 Receiver Registration & Automatic binding (Smart Match IM ) With the FrSky ACCESS protocol, the transmitter/transmitter module can bind receiver without using the "REG" button. Follow the step below to finish the Registration & binding procedure: 1. Put the transmitter/transmitter module into [Reg] status. Version 1.0 1.1 For Taranis X-Lite Pro as an example, turn on the transmitter, go to the MENU-MODEL SETUP-PAGE 2, choose Internal or External RF, and select [Reg]_ 2. Connect the battery to the receiver while holding the button on the receiver. The RED LED and GREEN LED on the receiver will be on, indicating into the [Reg] status. Select [ENTER] on the transmitter, The RED LED and GREEN LED on the receiver will flash, and the transmitter displays [Registration 0k]. 3. Tum off the receiver. 4. Move the cursor to select the receiver 1 [Bind]. 5. Connect the battery to the receiver, the GREEN LED will flash, indicating into the [Bind] status. Select the RX, the GREEN will keep lit, and the transmitter displays [Bind successful]. 6. The transmitter exit [Bind], GREEN LED will keep lit, RED LED will be off, indicating Working normally. How to Switch FS (20ms) mode/HS (7ms) mode a) The factory default setting is FS mode. b) To go to the receiver [Options], select the 7ms PWM or not Note: The SBUS output is 7ms, no matter HSIFS mode. Warning: HS mode is only applied for digital servos. Other servos should select FS mode, otherwise servos will get hot and may bum out. Warning: [Options ] setting in flight will cause the failsafe. About OTA function For Taranis X-Lite Pro as an example, go to the SD CARD 2/7, and select the FIN, press the enter button, select [Flash receiver OTA], power on the receiver, select the RX, go to the [ENTER], complete the flash process, the transmitter will display [Flash successful]. Re-power the receiver and wait for 3 seconds, the Green LED starts flashing indicates the receiver works properly at the momemnt_ Note: Please do not do the binding operation in the near range while the firmware upgrading in progress. Note: Update the firmware after the receiver gets bound. FCC STATEMENT 1 _ This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operatiom 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TNJ technician for help. FrSky is continuously adding features and improvements to our products. To get the most from your product, please check the download section of the FrSky website for the latest update firmware and manuals FrSky Electronic Co., Ltd. Contact us : Add: F-4,Building C, Zhongiu Technolog Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: 01140164







Leave a Reply