FRIGIDAIRE EFMIS155 (01) PDF Document

Do not plug the beverage center into a power outlet until it has been resting in its upright position for at least six (6) hours.

If the FRIGIDAIRE EFMIS155 has been laid on its side, placed upside down or tilted more than 45° during moving or transport, it is extremely important to allow the refrigerant and compressor oil to separate and settle so the compressor operates properly. Failure to do so will cause severe mechanical problems with the unit’s motor/compressor.

For the FRIGIDAIRE EFMIS155 to function efficiently, it MUST be placed in an adequately ventilated space to allow for heat dissipation. It is important to allow at least 2 inches (50 mm) of space on each side and above the unit, and 4 inches (100 mm) of space behind the unit.

The door requires approximately 22 inches (558 mm) of space in front of the beverage center to open fully to 160°.

The beverage center must be placed on a flat, stable surface. Adjust the unit’s front leveling legs to assure quiet operation and prevent rattling when the compressor activates.

IMPORTANT:

• Never place the unit on soft materials such as foam, plastic or thick textured carpeting.

• Make sure the unit and door are aligned. Use the adjustable legs (front only) to align the unit and/or the screws under the triangular bracket cover to align the door.

This beverage center is equipped with a 115V/60Hz single phase motor. Do not use a ground-fault circuit interrupter (GFCI) outlet to connect the unit. The power plug is a standard grounded three-prong non-polarized flush mount, which allows for easier connection to power outlets.

The power plug must be connected to the outlet directly, and never to an extension cord. Do not cut or remove the third ground prong from the power cord. Never shorten, lengthen, fold, or coil the power cord.

IMPORTANT: Never place the excess length of power cord into the compressor enclosure in the back of the beverage center. This action creates a dangerous heat build-up which can melt the cord, cause an electrical hazard and may potentially cause a fire.

To remove any manufacturing dust and residual odors, wipe the beverage center inside and out with a damp cloth and a solution of baking soda and warm water (2 tbsp. baking soda to 1 qt. water). Wipe away any residual baking soda with a clean moist cloth. Allow to dry before operating.

Periodically clean the beverage center with a sponge or cloth moistened with mild soapy water, or baking soda and water.

Protect From Moisture: Heavy moisture in the environment can cause degradation to the insulation, as well as rust to the cabinet, compressor and/or power supply. Do not spray the beverage center with water.

Protect From Heat: Place the beverage center away from heat source or direct sun. Do not operate your beverage center outdoors or in an environment with high temperatures and/or high humidity, such as garages, attics or outdoor patios. The temperature variances will create condensation on the glass door. Do not cover the beverage center with tarps or other items while operating, as this may cause overheating.

You will need a Phillips screwdriver #2.

1. The stainless steel handle is attached to the left side of the glass door with two enclosed screws.

2. Carefully pull back the gasket from the interior door frame as indicated. Insert screws into holes on the back side of the door under the door gasket. Position the handle on the outside of the glass door.

3. Tighten both screws until the door handle is flush with the stainless steel frame. Take care not to over tighten the screws, as this may damage the handle or frame.

4. Gently press and thread the gasket back into the slot on the door frame. Ensure the gasket is properly seated prior to using the unit.

IMPORTANT: DO NOT USE THE STAINLESS STEEL HANDLE TO MOVE OR LIFT THE UNIT.

You will need a Phillips screwdriver #2 or 5/16″ (8 mm) socket tool and a thin flathead screwdriver. If you plan on reversing the door hinges, DO NOT plug the beverage center into the power outlet. REMOVE GLASS SHELVES BEFORE REVERSING THE DOOR.

IMPORTANT: NEVER LAY THE BEVERAGE CENTER ON ITS BACK.

1. Gently remove the plastic hole insert plugs from the left side of the beverage center with a thin flathead screwdriver. Save the plugs for Step 11.

2. Loosen the triangular bracket cover by pushing the bracket cover towards the back of the beverage center and simultaneously pulling up.

3. Slide the cover towards the front of the beverage center and lift off.

4. Remove the metal bracket by unscrewing the three screws.

5. Lift and remove the door.

6. Rotate the door 180° so that the handle is on the opposite side.

7. With the unit on its side, remove the bottom metal base bracket with nylon washer. Unscrew the axle insert with a flathead screwdriver and screw it into the opposite hole of the metal base bracket.

7a. Gently place the beverage center on its opposite side to complete the door reversal. Remove the screw on the top hinge and re-insert it into the opposite side. Re-attach the metal base bracket with the nylon washer on the new hinge side. Lift the unit to an upright position.

8. To reattach the door, place the door onto the bottom axle insert. Place the top bracket into the door and align the metal bracket holes over the holes in the top of the unit cabinet. Tighten the three screws to hold in place.

9. The rubber gasket should be compressed on all sides of the door. If the gasket is more compressed on one side, the metal bracket position should be adjusted. Make sure the door is level. Once the door position is finalized, securely tighten the screws.

10. Reinstall the triangular bracket cover by carefully threading the bracket cover onto the metal bracket and pressing down.

11. Reinstall all plastic hole insert plugs. The re-installation of the plugs is important to maintain the seal and integrity of the insulation. Extra inserts are included in case the plugs are damaged during removal.

IMPORTANT: It is extremely important to wait at least six hours before plugging the beverage center into a power outlet after the door reversal process. The refrigerant and compressor oil fluids need time to separate and settle.

After connecting the power cord, you will hear a short beep. The default temperature is 43°F. Use the up and down arrow buttons to set the desired temperature between the range of 40°F – 61°F.

The display will flash while the temperature is being set. After a few seconds, it will revert to its current internal temperature reading. The digital display reading will adjust as the unit cools. While the unit is adjusting, you can press the up or down buttons to view the selected temperature setting.

If there is a power outage, the unit will revert to the last temperature setting once power is restored.

When first loading the beverage center to full capacity, we recommend the following steps to effectively cool a large number of beverages:

1. Use the Adjustable Thermostat Control to set the temperature to 43°F (the default temperature).

2. Allow the beverage center to cool for a minimum of two hours.

3. Load the beverages. To achieve maximum capacity, refer to the loading diagrams.

4. After initially filling with beverages, the internal temperature will rise as indicated on the display.

5. Once the beverage center has cooled the beverages to 43°F, use the Adjustable Thermostat Control to select a desired cooler internal temperature (lowest temperature setting is 40°F).

6. Allow several hours for the beverage center to cool to the desired lower temperature.

Note: It is normal for temperature variances to occur inside the unit, and areas near the door will have slightly warmer temperatures.

The beverage center accommodates 126 beverages (standard 12 ounce cans). To accommodate all 126 beverages, position the glass shelves and load the beverages as shown:

• ROW 1: 30 cans (Upright)

• ROW 2: 30 cans (Upright)

• ROW 3: 18 cans (Laying Down)

• ROW 4: 24 cans (Upright)

• ROW 5: 24 cans (Upright)

The glass shelves can be adjusted to accommodate varying sizes of beverage cans and bottles. For bottles, nest them to gain greater capacity.

Press the light bulb button to turn the LED light on and off. To enhance the lifespan of the LED light and conserve energy, it is recommended to predominantly utilize the light for loading and selecting beverages.

Frost may develop on the interior back panel when the temperature setting is very low and the unit is not fully stocked. To defrost the beverage center:

1. Use the up and down arrow buttons to increase the temperature until the compressor turns off.

2. Allow the internal ice/frost buildup to melt. Ensure the internal drain (located at the middle back of the lower shelf) is not clogged.

3. During this time, the melted frost flows through an internal drain into a holding pan on top of the compressor. The heat of the compressor evaporates the liquid.

4. Reset the temperature to 43°F and allow to cool for at least one hour.

5. Adjust to the desired temperature setting.

It is important to periodically clean and maintain the beverage center. When performing maintenance, make certain the unit is unplugged from the power outlet.

Wipe the inner and outer surfaces of the beverage center clean with a damp cloth. If needed, use a gentle detergent or a solution of baking soda and water. Remove any residue with clean water and a soft cloth, then dry with another cloth.

Once clean, you may use a common kitchen appliance wax on outer surfaces.

Inspect, clean and maintain the rubber gasket around the door. A small amount of petroleum jelly applied to the bracket side of gaskets will keep the gasket pliable and ensure a good seal.

IMPORTANT:

• Do NOT use hot water, harsh detergents, gasoline, kerosene, solvents, acids or anything flammable to clean the beverage center.

• Do NOT spray the beverage center with water as this may cause rust and degrade the insulation.

• Do NOT clean glass shelves with hot water when they are cold. Shelves may break if exposed to sudden temperature changes or impact.

You will need a Phillips screwdriver and a flashlight.

Removing the Existing LED Light:

1. Unplug the beverage center.

2. Using a Phillips screwdriver, remove the two screws from the clear plastic cover.

3. Tilt the panel towards the front of the beverage center and unscrew the LED board from the black plastic spacer.

4. Gently unclip the power cable from the red socket insert on the LED board.

Installing the Replacement LED Light:

1. Insert the power cable into the red socket insert on the replacement LED board.

2. Position within the black plastic spacer.

3. Reassemble the LED board, spacer and cover together using the two screws.

4. Tuck the cable into the wire slot.

5. Reposition the panel and carefully enclose the cord within the LED housing.

6. Reattach the clear plastic panel using two screws.

• Check for power failure.

• Verify unit is plugged into a standard power outlet and not a GFCI outlet.

• Check if the control panel is on.

Adjust the thermostat to a higher number (warmer temperature).

• Adjust thermostat to lower number.

• Ensure door is closed properly.

• Ensure the door gasket provides a proper seal. If you can slide a piece of paper between the gasket and unit body, the gasket is not sealing properly.

• Unit may not have enough ventilation space around it.

• Do not put hot beverages in the beverage center.

• Hot weather and/or frequent door opening will force the unit to work harder to keep cool.

• Do not overload the beverage center.

• Do not put hot beverages in the beverage center.

• The unit may be tilted. Adjust the front legs to level the unit.

• Align the door using a 5/16″ (8 mm) socket, adjusting the screws under the triangular bracket cover.

The unit exchanges heat through the side walls; this is normal operation and does not indicate a malfunction. This usually happens when the door is opened and closed frequently, or when operated in high temperature weather. It results from dissipation of heat from within the unit. Do not touch the panel.

• Condensation forms under conditions of high humidity; this does not indicate a failure. Wipe condensation with a dry towel.

• Relocate the unit to a cooler area or adjust the thermostat to a higher setting to balance out the exterior and interior temperatures. Condensation will dissipate as time goes on.

• A sound of trickling water is the refrigerant flowing. This does not indicate a malfunction.

• A buzzing noise is typically generated by the compressor when starting up or shutting down.

• The appliance must be correctly installed and connected to a properly grounded power supply.

• Do not use an extension cord.

• When transporting, keep the unit upright. Do not tilt beyond 45°.

• Do not touch the cooled surfaces with wet hands, as skin may stick.

• Position the unit away from combustible sources like gas, petrol, alcohol, etc.

• Unplug your unit before cleaning or making any repairs.

• Do not defrost with electrical devices or scrape ice with sharp tools.

• Do not run the power cord over carpeting or submerge it in water.

• Do not operate in the presence of explosive fumes.

• WARNING – Do not use flammable materials on or near the unit.

• DANGER – Risk of Fire or Explosion. Flammable Refrigerant Used. To Be Repaired Only By Trained Service Personnel. Do Not Puncture Refrigerant Tubing.

DANGER – Risk of child entrapment. Before you throw away your old unit:

• Take off the doors.

• Leave the shelves in place so that children may not easily climb inside.

The shelves should remain in the beverage center for disposal. This deters children from climbing into the unit, becoming trapped and potentially suffocating.

• CAPACITY OF BEVERAGE CENTER IN CU FT: 4.4 CU FT

• SHELF MATERIAL: GLASS

• TEMPERATURE CONTROL TYPE: ELECTRONIC TEMPERATURE CONTROL

• TEMPERATURE RANGE: 40°F – 61°F / 4°C – 16°C

• DIMENSIONS:

– DEPTH (EXCLUDING HANDLES)(IN): 21.25

– DEPTH (INCLUDING HANDLES)(IN): 22.72

– DEPTH (LESS DOOR)(IN): 19.02

– DEPTH WITH DOOR OPEN 90 DEGREES (IN): 40.31

– HEIGHT TO TOP OF DOOR HINGE (IN.): 31.22

– PRODUCT DEPTH (IN.): 21.25

– PRODUCT HEIGHT (IN.): 31.38

– PRODUCT WIDTH (IN.): 20.50