FLEXISPOT E1B (01) PDF MANUAL

The specifications are as follows:

Max. Weight Capacity: 154 lbs (70 kg)

Speed: 1″/s

Input Voltage: 100 – 240 V

Min. Height: 28″ (710 mm)

Max. Height: 47.6″ (1210 mm)

Desktop size compatibility: 39.3″ – 63″ (1000 – 1600 mm) in width and 19.7″ – 31.5″ (500 – 800 mm) in depth

Duty Cycle: 10% (Working 2 minutes then stop 18 minutes)

Working Temperature: 32° – 104° F

Accessory Package:

A: M6x16mm bolts (x12)

B: M8x50mm bolts (x4)

C: 5×5 hex key (x1)

D: 2.5×2.5 hex key (x1)

E: M4x6mm bolts (x2)

F: ST4.2X20mm screws (x14)

G: (x1, item not specified)

Note: Figures shown are for reference only. Please contact customer service if there are any accessory or tools missing.

Parts Included:

1. Desk foot (Qty 2)

2. Desk leg (Qty 1)

3. Desk leg (Qty 1)

4. Beam (Qty 1)

5. Transmission rod (Qty 1)

6. Bracket (Qty 2)

7. Control box (Qty 1)

8. Baffle (Qty 1)

9. Handset (Qty 1)

10. Power cord (Qty 1)

Step 1: Attaching the desk feet

Attach the desk feet (1) to the legs (2 & 3) using 8 M6x16mm bolts (A). Tighten with the 5×5 hex key (C).

Step 2: Attaching the beam

Turn the leg (2) down. Attach the beam (4) to the legs using M8x50mm bolts (B) and tighten with the 5×5 hex key (C). Then attach the other desk leg (3). The beam can be adjusted (Loosen/Stretch/Tighten) to fit your desktop size.

Step 3: Install transmission rod

Attach the transmission rod (5) to the desk legs (2 & 3). Attach to leg (2) first, then attach to the other one (3). Tighten with the 2.5×2.5 hex key (D). Warning: To ensure the motor works correctly, please make sure to rotate less than 1/3 circle when inserting and tightening the transmission rod.

Step 4: Install bracket

Attach the bracket (6) to the desk legs (2 & 3) using 4 M6x16mm bolts (A). Tighten with the 5×5 hex key (C).

Step 5: Install worksurface, control box, and baffle

Place the worksurface (not included) and attach it to the bracket (6) using ST4.2X20mm screws (F) and tighten with a drill. Ensure it is attached under 7.9″ (200 mm) from both edges of the worksurface.

Install the control box (7) and handset (9) (typically under the worksurface).

Attach the baffle (8) to the beam using M4x6mm bolts (E) and tighten with the 2.5×2.5 hex key (D).

Step 6: Connect cables

Connect the handset cable, power cord (10), and motor cable to the control box (7) as shown in the picture, using the designated interfaces.

The handset buttons have the following functions:

▲ (UP Button): Used to lift the desk surface.

▼ (DOWN Button): Used to lower the desk surface.

“1”: Recalls the 1st saved height position.

“2”: Recalls the 2nd saved height position.

“3”: Recalls the 3rd saved height position.

“M” (SAVE button): Used to save the current height position.

“A” (REMINDER button): Used to activate the “Long-Time Sitting Reminder” function.

Adjusting Desk Height:

Press the UP button (▲) or DOWN button (▼) to lift or lower the height of the desk surface. The LED display shows the real-time height value. The range of the height value is 27.9″ – 47.5″.

Saving a Height Position:

a. Press the UP button (▲) or DOWN button (▼) to adjust the desk to your desired height. For instance, adjust the height to 29.5″.

b. Press the “M” SAVE button. The LED display will show “—“. Then press “1” to save the current height as the 1st height position (e.g., 29.5″). The LED display will show “S-1”.

c. Repeat steps a and b to save other height positions. For example, to save a 2nd height position at 39.5″, the LED display will show “S-2”. To save a 3rd height position at 47″, the LED display will show “S-3”.

d. To automatically go to a saved height, press “1”, “2”, or “3”.

a. Press the REMINDER button “A” to activate the function. The LED display shows “00”.

b. Two seconds later, the display screen will flash. Press the “▲” or “▼” button to adjust the reminder time (e.g., set to 45 minutes, display shows “45”). Then press any button to save the time setup, or wait 5 seconds and the system will save the time setup automatically. After the time setting is finished, the system will automatically enter the countdown. During the countdown, any operation will lead to a repeat starting of the timer. When the countdown finishes, the buzzer will be active with a 10-second “DiDi… DiDi…DiDi…” tone.

c. Within the 10-second reminder buzz, press any button to reactivate the time countdown that was set up in step (b). If no operation is performed during the 10-second reminder buzz, there will be another reminder buzz after 5 minutes. No operation during this second buzz will turn off the Long-Time Sitting Reminder.

d. To turn off the Long-Time Sitting Reminder, press and hold the “A” button for three seconds. The LED display will show “OFF”.

Reset function (RSI display): When the LED display shows “RSI”, press and hold the “▼” DOWN button until the desk reaches its lowest height and rebounds to stop. The display will then show the lowest height, and the reset process is finished.

Exception code E01 or E02: If E01 or E02 appears on the display, please wait 18 minutes before trying to operate the desk again.

If the “▼” DOWN button doesn’t work: Please check the cable connection to the control box. Then, cut off the power for at least 10 seconds. Reconnect the power. Press the “▼” DOWN button; the LED display should show “RSI”. Then start the reset process by pressing and holding the “▼” DOWN button as described above.

1. Check that all cables are connected well.

1. Check if the loading weight on the desk exceeds 154 lbs (70 kg).

1. Start the reset process. (When the LED display shows “RSI”, press and hold the “▼” DOWN button until the desk reaches its lowest height and rebounds to stop. The display will then show the lowest height.)

1. Check if the loading weight on the desk exceeds 154 lbs (70 kg).

1. Check if the loading weight on the desk exceeds 154 lbs (70 kg).

1. Keep the power on and stop working for 18 minutes to allow the motor to cool down.

1. Press and hold the “M” (SAVE) button and the “3” button simultaneously for three seconds until you hear a BEEP twice. This will restore the factory settings.

Power and Environment:

Power supply: AC100-240 V, frequency 50/60HZ.

Working environment: 32° – 104° F.

Cleaning:

Before cleaning, unplug the power supply cable. Clean with a slightly damp cloth to wipe away surface dust. Keep all electrical components away from liquids. Do not damage the connection line and keep the plug in a safe position.

Do not use corrosive or abrasive materials to clean this product. Dispose of cleaning solutions in an environmentally friendly manner.

Installation and Operation:

Before using the product, ensure it has been installed correctly.

Before starting use, read the instructions to fully understand all functions and settings.

Slight noise caused by the multi wedge belt or brake system will not impact the use of this product.

Child Safety and Supervision:

Keep children away from electric height-adjustable desks, control units, and handsets.

Children or those with cognitive impairment should not use this product without supervision.

Power Cord:

If the power supply cord is damaged or broken, it must be replaced by the manufacturer or a relevant specialist to avoid any injuries.

Safe Environment and Packaging:

Operate in a clean and safe environment. Do not leave tools around. Be careful when dealing with packaging materials to avoid potential dangers, such as the choking risk plastic bags pose to children.

Transportation:

If necessary, retain the original package for future transportation.

This product cannot be disposed of as household waste. To prevent damage to the environment, this product should be recycled. Please use the relevant recycling systems available to you.

Inside the control box, there are electronic components, metal parts, plastic parts, wires, and so on. These should be disposed of in accordance with local laws and regulations and not as household waste.