FIVESTAR PN281-7W (01) PDF Document

Before moving the FIVESTAR PN281-7W indoors:

Remove outer carton and packing material from the shipping base. The range is now ready for removal from the wooden base.

Due to the weight of the FIVESTAR PN281-7W range, use a dolly with soft wheels to move it.

Lift the range onto the dolly and move indoors.

The range should be placed onto sliders to prevent damage to the floor.

To simplify handling and to reduce the weight of the range:

Remove the grates and the burner pans.

Remove griddle/grill and housing.

Remove the broiler pan, racks and literature package from inside oven.

To remove oven door(s):

Open door fully.

Rotate the “hinge retainers” into the locked position, as shown over the hook located on the bottom side of each hinge quadrant.

Lift the door slightly, to clear “hinge slots”, and pull straight out to clear hinge mechanism from main front opening.

The FIVESTAR PN281-7W range must be supplied with 120 volt, 60 Hz. and connected to an individual, properly grounded branch circuit protected by a 15 amp circuit breaker or time delay fuse.

ELECTRICAL REQUIREMENTS FOR ALL GAS RANGES:

120 volts, 60 Hz, 15 amps

The power cord of this appliance is equipped with a three-prong (grounding) plug which mates with a standard three-prong grounding wall receptacle to minimize the possibility of shock hazard from this appliance.

If the electrical service provided does not meet the above specifications, it is recommended that a licensed electrician install an approved outlet.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER CORD.

DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE.

Locate the electric supply within the area shown or within reach of the cooktop’s six foot power cord.

To avoid tangling cord with items stored in the cabinet, locate the receptacle or rear wall, inside the cabinet.

Because hard piping restricts movement of the range, the use of an A.G.A. certified flexible metal appliance connector is recommended unless local codes require a hard-piped connection.

Never use an old connector when installing a new range. If the hard piping method is used, you must carefully align the pipe; the range cannot be moved after the connection is made.

To prevent gas leaks, put pipe joint compound on, or wrap pipe thread with Teflon* tape all around male (external) pipe threads.

6-1. Install a manual gas shut-off valve in the gas line in an easily accessed location outside the range. Make sure everyone operating the range knows where and how to shut off the gas supply to the range.

6-2. Install male ½” flare union adapter to the ½” NPT internal thread at inlet of the regulator. Use a backup wrench on the regulator fitting to avoid damage.

6-3. Install male ½” or ¾” flare union adapter to the NPT internal thread of the manual shut-off valve, taking care to back-up the shut-off valve to keep it from turning.

6-4. Connect flexible metal appliance connector to the adapter on the range. Position range to permit connection at the shut-off valve or vise versa.

6-5. When all connections have been made, make sure all range controls are in the off position and turn on the main gas supply valve. Use a liquid leak detector at all joints and connections to check for leaks in the system.

When using test pressures greater than ½ psig to pressure test the gas supply system of the residence, disconnect the range and individual shut-off valve from the gas supply piping. When using test pressures of ½ psig or less to test the gas supply system, simply isolate the range from the gas supply system by closing the individual shut-off valve.

NOTE: PLEASE READ ALL INSTRUCTIONS BEFORE STARTING INSTALLATION.

7-1

Remove the burner grates, griddle/grill and housing.

7-2

From the front of the range, remove the Phillip screws in the rear of each burner pan (black pan where the top burners are located).

7-3

From the rear of the range, remove two screws from the rear of the side panels, the upper most screw on each side. You will need a 5/16″ nut-driver or 5/16″ socket to remove these screws. (Tools with a magnetized tip will be helpful in replacing the backguard screws.)

7-4

From the rear of the range, locate the upper wire cover with tab slots. Remove two 5/16” mounting screws. This cover will be reinstalled once the backguard is installed.

7-5

Screws are installed in the backguard, at the Factory for assembly to the backguard support. It is important that you locate and remove these four screws from the backguard before you attempt to install the backguard to the range backguard support.

7-6

Remove the vinyl protective covering from the front of the backguard.

7-7

The front of the backguard should fit between the back burner pans and the rear support. If the burner pan and rear support have a tight tolerance, place a thin bladed screw driver at either end, between the burner pan and rear support, to start placement of the backguard. Slide the backguard over the exhaust vent(s). Align the slots in the front of the backguard with the rear support bar locator studs.

7-8

With the backguard in position, secure the backguard to the rear backguard support using the four 5/16″ screws removed in step 7-4, re-install the screws in the edge of the side panels and replace the screws in the back of each burner pan. Re-install griddle/grill housing. Do not re-install the grates at this point.

7-9

Reinstall the upper wire cover that was removed in Step 7-4. Place the cover into position with the lower backguard panel fitting into the tab slots. Reinstall the two 5/16” mounting cover screws.

1. Remove shipping tape from the leveling legs.

2. Carefully slide the range into position. Be careful not to damage the floor or entangle power cord and gas flexible tubing.

3. To adjust leveling legs, turn counter-clockwise to raise the range; clockwise to lower. “Channel-lock” type pliers are recommended. Avoid using a pipe wrench which can scar the legs.

IMPORTANT: The range should always be installed at countertop height or higher. DO NOT INSTALL THE RANGE LOWER THAN ADJACENT COUNTERTOP HEIGHT, DUE TO RISK OF A FIRE HAZARD

To replace the oven door(s):

Insert hinges into front frame opening locating “hinge slots” on front frame as shown.

Rotate “hinge retainers” back into the “open” position.

Rotate door to make sure it functions properly.

CAUTION:

Take care when replacing the oven doors. If the hinge latch is not securely locked, the hinge may snap back and separate. If the hinge separates, you must apply pressure (possibly with your foot) to press it back together and then engage the hinge tech.

1. Re-check to make sure tape has been removed from leveling legs.

2. Place range in proper location with back of range against rear wall.

3. Adjust leg levelers to match counter height.

4. Remove range and install anti-tip bracket to wall. (See Note: Fig. 2)

5. Re-install range. Anti-tip bracket flange must enter slot in back to prevent tipping.

Check for proper ignition:

Push in one control knob and turn 45° counter clockwise to LITE position.

The igniter will spark and the burner will light; the igniter will cease sparking when the burner is lit.

First test may require some time, while air is flushed out of the gas line.

Turn knob to OFF.

Repeat the procedure for each burner.

IMPORTANT: If the ignitor electrodes continue to spark after the burners are lit, check that each burner component is assembled and seated properly. Disassemble and reassemble as required.

Burner flames should be blue and stable with no yellow or yellow tips, excessive noise or lifting of the flame from the burner. If any of these conditions exist, check that the burner ports are not blocked. If one of these conditions continues, call for service. Reminder: This product must be operated with the fuel that it was produced for at the factory.

GAS OVEN

Turn oven thermostat knob counter clockwise to 350°.

The oven burner should light within 60 seconds.

Turn gas supply “on”.

Turn electric supply “on”.

MAKE SURE ALL CONTROLS ARE IN THE “OFF” POSITION.

Gas supply is “on”

Electric power is “on”

Check for proper seating of burner caps into burner base

Burner grates in position

Oven and broiler racks installed

Surface burner ignition test

Gas oven ignition test

Check operation of convection fan

MAKE SURE ALL CONTROLS ARE LEFT IN THE “OFF” POSITION.