Post questions, comments, reviews or page errors in the comment box below.

Click here to download FELLOWES FORTISHRED 2250S (01) PDF MANUAL

PDF Content Summary:

****** Page 1 ****** Fellowes FORTISHREDM 2250C/2250S/2250M HE WORLD’S TOUGHEST SHREDDERS Fellowes. Please read these instructions before use. Do not discard: keep for future reference. Fellowes Quality Office Products Since 1 91 7

****** Page 2 ****** B. c. D. E. CAPABILITIES Will shred: G. H. KEY A. Safety Shield B. Paper entry C. Disconnect switch (open door) D. Door E. Basket (inside) F. Casters G. See safety instructions Maximum: Paper entry width ENGLISH Model 2250(/2250s/2250M H. Control Panel and LEDs Ö l. (blue) R 2. Reverse (red) 13 3. Bin full (yellow) Q 4. Door open (red) 5. Safety Shield Open (red) 2250C and 2250S: Paper, staples, paper clips, credit cards, CD/DVDs and junk mail. 2250M: Paper, paper clips, staples and credit cards. Will not shred: Adhesive labels, continuous form paper, transparencies, newspaper, cardboard, laminates, file folders, X-rays or plastic other than noted above Paper shred size: 5/32 in. (4mm) Strip-Cut 5/32 in. x 1-9/16 in. (4mm x 40mm) Cross-Cut 2/32 in. x 9/1 6 in. (2mm x 15mm) Micro-Cut *In order to perform at capacity, shredder must be plugged into a dedicated 15Amp, 120V outlet and oiled every 15-30 minutes of continuous use. *8.5″ xl I m, 201b., (75g) paper at 120! 60 Hz, 5.6Amps; heavier paper, humidity or other than rated voltage may reduce capacity. AWARNING: IMPORTANT SAFETY INSTRUCTIONS – Read Before Using! Operation, maintenance, and service requirements are covered in the instruction manual. Read the entire instruction manual before operating shredders. Keep away from children and pets. Keep hands away from paper entry. Always set to off or unplug when not in use. Keep foreign objects — gloves, jewelry, clothing, hair, etc. — away from shredder openings. If object enters top opening, switch to Reverse (R) to back out object. Never use aerosol products, petroleum based lubricants or other flammable products on or near shredder. Do not use canned air on shredder. Do not use if damaged or defective. Do not disassemble shredder. Do not place near or over heat source or water. Do not operate the machine without the safety shield closed (A). This shredder has a Disconnect Power Switch in the cabinet door. The door must be fully closed to operate shredder. In case of emergency, open cabinet door. This action will stop shredding immediately. Avoid touching exposed cutting blades Under shredder head. Shredder must be plugged into a properly grounded woll outlet or socket of the voltage and amperage designated on the label. The grounded outlet or socket must be installed near the equipment and easily accessible. Energy converters, transformers, or extension cords should not be Used with this product. FIRE HAZARD — Do NOT shred greeting cards with sound chips or batteries. For indoor use only. Unplug shredder before cleaning or servicing.

****** Page 3 ****** BASIC SET UP SHREDDER SET-UP Open the door Place (Utter head into Ensure accesstoa Make sure safety flap top of cabinet, use 2 dedicated 15Amp, is securely in place 120! outlet people ADVANCED PRODUCT FEATURES BASIC SHREDDING OPERATION TO SHRED Feed paper straight When finished Plug in and make Press (Ö) ON to sure door is closed activate Safety Shield Electronically controlled shield stops shredder when opened for advanced safety into paper entry and shredding set to release OFF Do nothing and shredder will automatically shut off after 30 minutes of inactivity SilentShredTM Technology SilentShredTM noise quality shreds without noisy disruptions. PRODUCT MAINTENANCE SAFETY O AUTO Auto Shut Off SHUT OFF After 30 minutes of inactivity, shredder automatically turns off for zero energy consumption CLEANING AUTO-START INFRARED SENSORS Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors may become blocked by paper dust causing the motor to run even if there is no paper present (Note: two paper detection sensors are located in the center of the paper entry). OILING SHREDDER All cross-cut and micro-cut shredders require oil for peak performance. If not oiled, a machine may experience diminished sheet capacity, intrusive noise when shredding and could Ultimately stop running. To avoid these problems, we recommend you oil your shredder each time you empty your waste bin or every 15-30 minutes of continuous use. FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE Turn off and unplug shredder Locate Auto-start infared sensor Use thin, long-handled brush to clean sensors. Make sure brush is clean and dry Clean any contamination from the poper sensors Set to Off (C)) and unplug *Apply oil across entry Press Reverse (R) TROUBLESHOOTING *Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250 Gently pull uncut paper If necessary, press Shred I sheet of When flashing blue, Ö D Bin Full Indicator: When illuminated, the shredder waste bin is full and needs to be emptied. Use Fellowes waste bag 36054. Safety Shield Indicator: When flashing alternatively with On/0ffÖ LED, safety shield is open and shredding will stop. To resume shredding, make sure safety shield is closed. Door Open Indicator: When flashing alternatively with On/0ff ÖLED, the door is open. To resume shredding, make sure door is closed. Paper Capacity Indicator: When flashing blue, too much paper is inserted. Shredder will automatically stop and reverse paper. See Paper Jam section. Overheat Indicator: When flashing alternatively with On/0ff Ö LED, shredder requires a 10-15 minute cool down period. When Ois blue, resume shredding. from paper entry too much paper is inserted. Shredder will automatically stop and reverse paper paper to clear Reverse (R) to run shredder in reverse cutters. Resume and then pull uncut normol shredding paper from shredder

****** Page 4 ****** Fellowes LIMITED PRODUCT WARRANTY FORTISHREDM 2250C/2250S/2250M THE WORLD’S TOUGHEST SHREDDERS Limited Warranty: Fellowes, Inc. (“Fellowes”) warrants the parts of the machine to be free of defects in material and workmanship and provides service and support for 2 years from the date of purchase by the original consumer. Fellowes warrants the cutting blades of the machine to be free from defects in material and workmanship for 30 years from the date of purchase by the original consumer. If any part is found to be defective during the warranty period, your sole and exclusive remedy will be repair or replacement, at Fellowes’ option and expense, of the defective port. This warranty does not apply in cases of abuse, mishandling, failure to comply with product usage standards, shredder operation using an improper power supply (other than listed on the label), or unauthorized repair. Fellowes reserves the right to charge the cormjmers for any additional costs incurred by Fellowes to provide parts or services outside of the country where the shredder is initially sold by an authorized reseller. ANY IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable for any consequential or incidental damages attn%utable to this product. This warranty gives you specific legal rights. The duration, terms, and con&ltions of this warranty are valid worldwide, except where different limitations, restrictions, or conchtions may be required by local law. For more details or to obtain service under this warranty, ple(ße contact us or your dealer. Questions or Concerns? w w.fellowes.com Troubleshooting Registration Manuals Canada Mexico United States Fellowes Custotper Service & Support Troubleshooting Replacement parts General questions +1-800-665-4339 +011 -800-514-9057 +1-800-955-0959 1789 Norwood Avenue, Itasca, Illinois 60143-1095 • USA• 630-893-1600 02012 Fellowes, Inc. Part No. 407242 fellowes.com







Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.