EUROM HI-TOWER 2200 WI-FI (01) PDF MANUAL

Supply voltage: 220-240V~50Hz

Maximum capacity: 2200 W

Settings: fan-1100-2200 W

Oscillate: Yes

Thermostat: Yes

Remote control: Yes (including CR2025 battery)

Dimensions: 22.9 x 23.2 x 77.6 cm

Weight: 3.5 kg

Read the user instructions carefully and completely before using (and installing) this device. Keep the instruction leaflet somewhere safe so that you can consult it and pass it on in future.

Before use, check your new device (including cable and plug) for any visible damage. Never use a damaged device but take it back to the supplier for a replacement.

In the event of incorrect usage or installation, there is a risk of electric shocks and/or a fire hazard.

This device is not suitable for wall or ceiling installation.

Do not use this device in the immediate vicinity of a bath, shower or swimming pool.

This device is not suitable for use in damp spaces such as bathrooms, wash rooms etc. Never locate the device near water-points and reservoirs (tap, bath, shower, toilet, sink, swimming pool, etc.). Make sure that the device cannot fall into water and that it cannot be penetrated by water. If the device falls into water make sure you remove the plug from the socket! Do not use a device that is wet inside but take it to be repaired. Never immerse the device, cable or plug in water or any other fluid and never touch device with wet hands.

The air around the device must be able to circulate freely. Never install it too close to walls or large objects and never under a shelf, cupboard, curtains or similar. When locating the device, make sure you have the following minimum free space:

Front, minimum free space 100 cm

Back, minimum free space 30-50 cm

Sides, minimum free space 100 cm

Top, minimum free space 100 cm

Always place the unit on a sturdy, flat horizontal surface.

The base on which the device is placed must not be made of flammable materials. It must be resistant to temperatures of at least 125°C without burning, melting, deforming or bursting into flames. Check regularly to ensure that the surface is not overheating; this could be dangerous!

Never place the device on surfaces such as beds or deep-pile carpet as openings could be blocked.

Do not place the device near an open window as rain could blow in; do not place on wet surfaces and avoid any liquids being spilt nearby. Do not place the device behind a door or along a walking route to avoid accidental trips.

Do not place the device near, under or facing an electrical socket and not in the vicinity of an open fire or heat source.

Do not use the device nearby or facing furniture, curtains, paper, clothing, bedding or other flammable materials. Keep at least 1 metre from device!

Do not use the heater outdoors or in areas that are smaller than 15m³.

The device contains hot and/or glowing and sparking components. Do not, therefore, use where fuels, paint, flammable fluids and/or gases are stored. Do not use the device in an environment that poses a fire risk, e.g. near gas tanks, gas pipes or aerosols. This is an explosion and fire risk!

Do not use additions/accessories on the device that have not been supplied or approved by the manufacturer.

Only use the device for its intended purpose and in the manner set out in this instruction leaflet.

Some parts of this device will get very hot and could cause burns. You must pay particular attention to children, vulnerable persons and pets that are present near the device. Never leave them alone with a working device.

Never cover or block the device; it will overheat and this could lead to a fire risk. Never hang or place objects such as clothing, blankets, cushions, paper, etc. on the device. The minimum distance of 1 metre between the device and flammable materials must always be applied. Ventilation openings should never be blocked as this may pose a fire risk. Never use the device to dry clothing or place anything on it. Do not let anything lean against the device!

Do not set the device to come on automatically using a timer, clock or other facility. You must always check for safe conditions before using the fireplace! Never use the device with an external voltage regulator such as a dimmer or similar, as this could be dangerous!

The device is exclusively intended for normal, household usage. Only use for providing heat in your home.

Connection voltage and frequency, as given on the device, must correspond to that of the socket to be used and the electrical installation must be equipped with an earth leakage circuit breaker of 30 mA. The electrical socket that you are using must be to hand at all times in order to be able to remove the plug from the socket in the event of an emergency.

To avoid overloading and/or fuses being blown, do not use any other equipment on the same socket or electrical group as the one used for the device.

Unroll the electric cable for the device fully before inserting the plug into the socket and ensure that the electrical cable does not come into contact with the fireplace or get hot. Do not run the electrical cable under carpet, cover with mats, runners or similar and do not place in areas that are walked on frequently. Ensure that it cannot be stepped on and that no furniture is placed on top of it. Do not bend the electrical cable around sharp corners and do not roll up too tightly after use! Prevent the electrical cable coming into contact with oil, solvents and sharp objects. Check the cable and plug regularly for damage. Do not bend or pinch the electrical cable and do not wind it around the device; this could damage the insulation!

The use of an extension cable is not advised as this can lead to overheating and fire. If the use of an extension cable is unavoidable, make sure that it is not damaged and that it is an approved extension cable with a minimum diameter of 2×2.5 mm² and a minimum permitted capacity of 3000 Watt. Always fully extend the cable in order to prevent overheating.

Only connect the device to a fixed socket. Do not use multi-plug adapters or similar.

During use, the plug may begin to feel warm; this is normal. If it’s really warm, there may be something wrong with the socket. Please contact your electrician.

Always turn off the device and remove the plug from the power socket: Never turn the device off using the plug!

Prevent foreign objects entering the radiation/ventilation or outlet openings on the device. This may cause electric shock, fire or damage.

Never leave a working device unattended but switch off and then remove the plug from the socket.

Apart from manual use, this device can also be operated via an app. However you operate it, make sure that the safety guidelines are taken into account at all times!

Always remove the plug from the socket when the unit is not in use! Always remove plug by pulling on the plug itself; never pull on the electrical cable!

This device gets hot during use. Never touch the device when it is on or shortly thereafter; it could burn you.

Never operate the device with wet hands.

Children younger than 3 must be kept out of the vicinity of the device unless they are continuously supervised.

Children between the ages of 3 and 8 may only switch the device on or off if it is set up or installed at its usual location and they are supervised or have received instructions regarding the safe use of the device and understand the corresponding hazards. Children between the ages of 3 and 8 may not insert the plug into the socket, adjust the device settings or clean or maintain it.

This device can only be used by children from the age of 8 and elderly persons and persons with diminished physical or mental capacities or a lack of experience and expertise if they are supervised or have received instructions regarding the safe use of the device and understand the corresponding hazards.

Children may not clean or maintain the device without supervision.

Children may not play with the device.

Keep the device clean. Dust, dirt and/or deposits in the device often lead to overheating. Ensure that this type of build-up is regularly removed.

Always switch the device off, remove plug from socket and let the device cool down before you:

clean the device

users maintain the device.

touch or move the device.

Never switch the device on if you have noticed damage to the device itself, the cable or plug or if it does not work properly, makes strange noises, smells odd or you can see smoke, or if it has fallen or shows any other signs of damage. Remove the plug from the socket immediately. Take the entire device back to your supplier or a recognised electrician to be checked and/or repaired. Always ask for original parts to be used.

The device may only be opened and/or repaired by a competent and qualified person. Do not carry out your own repairs as this could be dangerous! Repairs carried out by unauthorised persons or changes made to the device could damage the dust/waterproof capacity of the device and will nullify the guarantee and the manufacturer’s liability.

If the electrical cable is damaged, it must be replaced by the manufacturer, their service department or somebody with similar qualifications in order to prevent creating a hazard.

Remove all the packaging materials and keep out of children’s reach. After removing the packaging, check whether the appliance shows any damage or any signs of faults/defects/failures. Do not use the appliance in case of doubt, but turn to your supplier for checking /replacing.

Remove the protective foil of the battery holder. For battery replacement, slide the battery tray out from the back of the remote, push the battery out, and replace with a CR2025 battery, ensuring the positive (+) side faces up, then slide the tray back in.

Choose an appropriate spot for the appliance, taking into account all the precautionary measures stated in the user guide.

Check whether the control button is on OFF (O).

Unwind the entire electric cable and push the plug into an appropriate 220-240V socket. To prevent overload, check whether there is no other appliance connected to the same group.

Operate the heater by setting the main switch to I (ON). The heater is now on stand-by. The display and control light are now blue.

From now on, the heater can be operated manually, with the remote control or with an App.

Press the ON/OFF button to start the heater. The fan starts to work and the display shows the ambient temperature.

Press the MODE button (on the remote control) to change the mode:

1x pressing (low heating capacity): the display shows 1 sun and the fan symbol.

2x pressing (high heating capacity): the display shows 2 suns and the fan symbol.

3x pressing (back to fanning): the display shows the fan symbol.

Press the OSCILLATE button (on the remote control) and the heater will start oscillating (swinging). Press once again and it will stop oscillating (swinging).

Press the TEMPERATURE UP or TEMPERATURE DOWN buttons to set the desired temperature to 10-35°C.

When the set thermostat temperature is reached, the heating element switches off and the fan remains on for 99 seconds. If the ambient temperature drops again below the thermostat temperature, the heater will start to operate again.

The heater operates at high heating capacity whenever the ambient temperature is more than 4°C below the set temperature.

The heater operates at low heating capacity whenever the ambient temperature is more than 2-4°C below the set temperature.

Press the ON/OFF button to stop the heater.

After switching off, the heater continues to cool for 99 seconds. The display counts down the seconds.

To switch off the heater completely, press the main switch O (OFF) and then remove the plug from the socket. Always keep the plug out of the socket when not using the heater!

For remote control only: Press the LIGHT button to switch off the control light.

To connect the appliance with the App, the Wi-Fi symbol must flicker rapidly:

To switch On the Wi-Fi function, press the MODE and TIMER buttons simultaneously on the appliance for 3 seconds. The Wi-Fi light will start flickering.

To switch Off the Wi-Fi function, press the MODE and TIMER buttons simultaneously on the appliance again for 3 seconds and the Wi-Fi light will extinguish.

If the Wi-Fi symbol on the device flashes slowly, press the Wi-Fi key for 3 seconds.

Your Eurom heater can be easily operated via the same WLAN, via another WLAN, or via 3G or 4G mobile network. This enables you to operate the heater remotely without directly supervising the heater. Be aware that also when you operate the heater remotely, you have to observe all the safety measures included in the user guide delivered with the appliance. Read and understand these safety measures and make sure that you comply with all these measures when operating remotely.

The heater is equipped with a topple safeguard which switches the heater off if it accidentally falls over. Once it is placed upright, it will begin to work again but you must unplug and check the heater for damage before reusing. If you find damage or the heater does not work correctly, do not use and have it checked or repaired!

The overheating safeguard switches the heater off if it overheats internally. This may occur if heater cannot release sufficient heat or cannot take in adequate fresh air. Generally, this is due to (partial) coverage of the heater, blocking of the air inlet/outlet grilles, installation too close to a wall, etc. If the device is sufficiently cooled, it should restart operation but if you do not remove the root-cause, it will probably switch off again. Regular overheating can lead to irreparable damage. In the event of overheating, always unplug the heater and remove the plug from the socket. Give the heater time to cool down, remove the cause of overheating and put the heater back on again. If the problems continue or you cannot identify a reason for the overheating, turn off the heater immediately and remove the plug from the socket. Contact your service point for repairs.

The heater can heat a room for a maximum of 9 hours. This autostop ensures that the heater switches off automatically.

Keep the heater clean. Deposits of dust and dirt in the appliance are a common cause of overheating so these should be removed regularly. Switch off the heater, remove the plug from the socket and allow the heater to cool down before cleaning or carrying out maintenance work.

Wipe the outside of the heater regularly with a dry or slightly damp cloth. Do not use aggressive soaps, sprays, cleaners or abrasives, waxes, polishes or chemical solutions!

Using a vacuum cleaner, carefully remove any dust and dirt from the grills and ensure that the air intake and outlet openings are clean. Be careful not to touch or damage any internal parts during cleaning!

The heater contains no other parts which need maintenance.

At the end of the season, store the cleaned heater in the original packaging if necessary. Store it upright in a cool, dry and dust-free place.

At its end of life, discard the device according to the local laws and regulations, or deliver the device to your supplier.