EPSON EB-L400U (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD EPSON EB-L400U (01) PDF MANUAL


PDF Content Summary: User's Guide Contents 2

Notations Used in This Guide 7 Introduction to Your Projector 8 Projector Features.............................................................................. 9 Long-life Laser Light Source ........................................................................................................ 9 Quick and Easy Setup..................................................................................................................... 9 Easy Wireless Projection................................................................................................................ 9 Projecting for Exhibitions........................................................................................................... 10 Projector Parts and Functions ........................................................ 11 Projector Parts - Front/Top ........................................................................................................ 11 Projector Parts - Rear.................................................................................................................... 12 Projector Parts - Base ................................................................................................................... 13 Projector Parts - Interface Ports ............................................................................................... 13 Projector Parts - Control Panel ................................................................................................. 14 Projector Parts - Remote Control ............................................................................................ 15 Setting Up the Projector 17 Projector Placement ........................................................................ 18 Projector Setup and Installation Options............................................................................. 19 Precautions on Installation .................................................................................................. 19 Projection Distance....................................................................................................................... 20 Projector Connections ..................................................................... 22 Connecting to a Computer........................................................................................................ 22 Connecting to a Computer for VGA Video and Audio .............................................. 22 Connecting to a Computer for HDMI Video and Audio ........................................... 23 Connecting to Video Sources ................................................................................................... 23 Connecting to an HDMI Video Source ............................................................................ 24 Connecting to a Component-to-VGA Video Source .................................................. 24 Connecting to External USB Devices ..................................................................................... 25 USB Device Projection ........................................................................................................... 25 Connecting to a USB Device ............................................................................................... 26 Disconnecting a USB Device ............................................................................................... 26 Connecting to a Document Camera ...................................................................................... 26 Connecting to an HDBaseT Transmitter .............................................................................. 27 Connecting to External Output Devices............................................................................... 27 Connecting to a VGA Monitor ............................................................................................ 28 Connecting to External Speakers ...................................................................................... 28 Attaching and Removing the Cable Cover .................................... 30 Attaching the Zoom Ring Locks...................................................... 31 Installing Batteries in the Remote Control.................................... 32 Remote Control Operation ........................................................................................................ 33 Using Basic Projector Features 34 Turning On the Projector ................................................................ 35 Home Screen................................................................................................................................... 36 Turning Off the Projector ................................................................ 37 Setting the Date and Time .............................................................. 38 Selecting the Language for the Projector Menus ......................... 40 Projection Modes ............................................................................. 41 Changing the Projection Mode Using the Menus ............................................................ 41 Setting the Screen Type .................................................................. 42 Adjusting the Image Position Using Screen Position...................................................... 42 Adjusting the Image Position Using Lens Shift............................. 44 Displaying a Test Pattern................................................................ 46 Available Test Pattern Image Adjustments ......................................................................... 46 Adjusting the Image Height............................................................ 48 Image Shape..................................................................................... 49 Correcting Image Shape with H/V Keystone ...................................................................... 49 Correcting the Image Shape with Quick Corner ............................................................... 51

Contents 3

Correcting Image Shape with Arc Correction..................................................................... 52 Resizing the Image with the Zoom Ring........................................ 54 Focusing the Image Using the Focus Ring..................................... 55 Selecting an Image Source.............................................................. 56 Image Aspect Ratio .......................................................................... 58 Changing the Image Aspect Ratio.......................................................................................... 58 Available Image Aspect Ratios ................................................................................................. 58 Projected Image Appearance with Each Aspect Mode .................................................. 59 Color Mode ....................................................................................... 63 Changing the Color Mode ......................................................................................................... 63 Available Color Modes................................................................................................................. 63 Turning On Automatic Luminance Adjustment ................................................................ 63 Adjusting the Image Color.............................................................. 65 Adjusting the Hue, Saturation, and Brightness.................................................................. 65 Adjusting the Gamma ................................................................................................................. 65 Adjusting the Brightness................................................................. 68 Light Source Life Span................................................................................................................. 69 Controlling the Volume with the Volume Buttons ....................... 71 Adjusting Projector Features 72 Projecting Two Images Simultaneously ........................................ 73 Unsupported Input Source Combinations for Split Screen Projection..................... 74 Split Screen Projection Restrictions........................................................................................ 75 Projecting a PC Free Presentation.................................................. 76 Supported PC Free File Types................................................................................................... 76 Precautions on PC Free Projection ......................................................................................... 76 Starting a PC Free Slide Show .................................................................................................. 77 Starting a PC Free Movie Presentation ................................................................................. 78 PC Free Display Options ............................................................................................................. 79 Projecting in Content Playback Mode ........................................... 81 Switching to Content Playback Mode................................................................................... 81 Projecting Your Playlists ............................................................................................................. 82 Adding Effects to Your Projected Image.............................................................................. 83 Content Playback Mode Restrictions..................................................................................... 84 Shutting Off the Image and Sound Temporarily .......................... 85 Stopping Video Action Temporarily .............................................. 86 Zooming Images............................................................................... 87 Using the Remote Control as a Pointer.......................................... 88 Saving a User's Logo Image ............................................................ 89 Saving Settings to Memory and Using Saved Settings ............... 91 Using Multiple Projectors................................................................ 92 Projector Identification System for Multiple Projector Control ................................... 92 Setting the Projector ID......................................................................................................... 92 Selecting the Projector You want to Operate .............................................................. 93 Matching the Image Colors ....................................................................................................... 94 Adjusting Color Uniformity........................................................................................................ 95 Adjusting RGBCMY........................................................................................................................ 96 Scaling an Image ........................................................................................................................... 97 Projector Security Features............................................................. 99 Password Security Types ............................................................................................................ 99 Setting a Password.................................................................................................................. 99 Selecting Password Security Types ................................................................................ 100 Entering a Password to Use the Projector................................................................... 101 Locking the Projector's Buttons ............................................................................................ 101 Unlocking the Projector's Buttons.................................................................................. 102 Locking the Remote Control Buttons.................................................................................. 102 Installing a Security Cable ....................................................................................................... 103 Using the Projector on a Network 104 Wired Network Projection............................................................. 105

Contents 4

Connecting to a Wired Network ........................................................................................... 105 Selecting Wired Network Settings........................................................................................ 105 Wireless Network Projection ........................................................ 108 Installing the Wireless LAN Module..................................................................................... 108 Selecting Wireless Network Settings Manually ............................................................... 109 Selecting Wireless Network Settings in Windows.......................................................... 111 Selecting Wireless Network Settings in Mac .................................................................... 112 Setting Up Wireless Network Security ................................................................................ 112 Supported Client and CA Certificates............................................................................ 114 Using a QR Code to Connect a Mobile Device ................................................................ 114 Using a USB Key to Connect a Windows Computer...................................................... 115 Wireless Network Projection from a Mobile Device (Screen Mirroring)........................................................................................ 116 Selecting Screen Mirroring Settings .................................................................................... 116 Connecting Using Screen Mirroring with the Miracast Function............................. 118 Connecting Using Screen Mirroring in Windows 10 ............................................... 118 Connecting Using Screen Mirroring in Windows 8.1 .............................................. 119 Secure HTTP.................................................................................... 121 Importing a Web Server Certificate Using the Menus .................................................. 121 Supported Web Server Certificates ................................................................................ 122 Monitoring and Controlling the Projector 123 Epson Projector Management ...................................................... 124 Controlling a Networked Projector Using a Web Browser ........ 125 Web Control Options................................................................................................................. 126 Controlling a Networked Projector in Content Playback Mode ............................................................................................... 129 Web Control Options in Content Playback Mode .......................................................... 130 Registering Digital Certificates from a Web Browser................. 134 Setting Up Projector Network E-Mail Alerts ............................... 135 Network Projector E-mail Alert Messages ......................................................................... 135 Setting Up Monitoring Using SNMP............................................. 136 Using ESC/VP21 Commands ........................................................ 137 ESC/VP21 Command List ......................................................................................................... 137 Cable Layouts ............................................................................................................................... 137 PJLink Support ............................................................................... 139 Crestron Connected Support........................................................ 140 Setting Up Crestron Connected Support........................................................................... 140 Controlling a Networked Projector Using Crestron Connected ............................... 140 Crestron Connected Operation Window ..................................................................... 142 Crestron Connected Tools Window ............................................................................... 143 Setting Projector Event Schedules............................................... 145 Adjusting the Menu Settings 148 Using the Projector's Menus ......................................................... 149 Using the Displayed Keyboard..................................................... 150 Available Text Using the Displayed Keyboard................................................................. 150 Image Quality Settings - Image Menu ......................................... 151 Input Signal Settings - Signal Menu............................................. 153 Projector Feature Settings - Settings Menu ................................ 155 Projector Setup Settings - Extended Menu ................................. 158 Projector Network Settings - Network Menu.............................. 163 Network Menu - Screen Mirroring Settings ...................................................................... 164 Network Menu - Basic Menu .................................................................................................. 165 Network Menu - Wireless LAN Menu .................................................................................. 166 Network Menu - Wired LAN Menu ....................................................................................... 168 Network Menu - Notifications Menu ................................................................................... 169 Network Menu - Others Menu ............................................................................................... 170 Network Menu - Reset Menu.................................................................................................. 171 Projector Information Display - Info Menu ................................. 172

Contents 5

Info Menu - Projector Info Menu .......................................................................................... 172 Event ID Code List................................................................................................................. 173 Info Menu - Light Source Info Menu ................................................................................... 174 Projector Reset Options - Reset Menu ......................................... 175 Copying Menu Settings Between Projectors (Batch Setup) ...... 176 Transferring Settings From a USB Flash Drive ................................................................. 176 Transferring Settings From a Computer ............................................................................ 177 Batch Setup Error Notification ......................................................................................... 178 Maintaining the Projector 179 Projector Maintenance .................................................................. 180 Cleaning the Lens........................................................................... 181 Cleaning the Projector Case.......................................................... 182 Air Filter and Vent Maintenance .................................................. 183 Cleaning the Air Filter ............................................................................................................... 183 Replacing the Air Filter ............................................................................................................. 185 Solving Problems 187 Projection Problems ...................................................................... 188 Projector Indicator Status ............................................................. 189 Using the Projector Help Displays................................................ 192 Solving Image or Sound Problems............................................... 193 Solutions When No Image Appears..................................................................................... 193 Solutions When "No Signal" Message Appears ............................................................... 193 Displaying From a Laptop.................................................................................................. 194 Displaying From a Mac Laptop........................................................................................ 194 Solutions When "Not Supported" Message Appears .................................................... 194 Solutions When Only a Partial Image Appears................................................................ 194 Solutions When the Image is not Rectangular................................................................ 195 Solutions When the Image Contains Noise or Static..................................................... 195 Solutions When the Image is Fuzzy or Blurry .................................................................. 196 Solutions When the Image Brightness or Colors are Incorrect ................................. 196 Solutions When an Afterimage Remains on the Projected Image .......................... 197 Solutions to Sound Problems................................................................................................. 197 Solutions When Image File Names are not Displayed Correctly in PC Free......... 197 Solving Projector or Remote Control Operation Problems....... 198 Solutions to Projector Power or Shut-Off Problems...................................................... 198 Solutions to Problems with the Remote Control............................................................ 198 Solutions to Password Problems........................................................................................... 199 Solution When "The Battery that Saves Your Clock Settings is Running Low" Message Appears........................................................................................................................ 199 Solving Network Problems ........................................................... 200 Solutions When Wireless Authentication Fails ................................................................ 200 Solutions When You Cannot Access the Projector Through the Web ................... 200 Solutions When Network Alert E-Mails are not Received............................................ 200 Solutions When the Image Contains Static During Network Projection............... 201 Solutions When You Cannot Connect Using Screen Mirroring................................. 201 Solutions When the Image or Sound Contains Static During Screen Mirroring Connection.................................................................................................................................... 201 Solutions to Problems in Content Playback mode..................... 203 Appendix 204 Optional Accessories and Replacement Parts............................. 205 Screens............................................................................................................................................ 205 Cables .............................................................................................................................................. 205 Mounts ............................................................................................................................................ 205 For Wireless Connection .......................................................................................................... 205 External Devices .......................................................................................................................... 206 Replacement Parts...................................................................................................................... 206 Screen Size and Projection Distance............................................ 207 EB‑L615U/EB‑L610U/EB‑L510U/EB‑L610W/EB‑L610....................................................... 207

Contents6 EB‑L400U/EB‑L500W/EB‑L500................................................................................................. 209 Supported Monitor Display Resolutions ..................................... 212 Projector Specifications ................................................................ 214 Connector Specifications ......................................................................................................... 215 External Dimensions...................................................................... 216 List of Safety Symbols (corresponding to IEC60950-1 A2) ........ 217 Laser Safety Information............................................................... 219 Laser Warning Labels................................................................................................................. 219 Glossary .......................................................................................... 221 Notices ............................................................................................ 223 FCC Compliance Statement.................................................................................................... 223 Indication of the manufacturer and the importer in accordance with requirements of EU directive.................................................................................................. 224 Restriction of Use ........................................................................................................................ 224 Operating System References................................................................................................ 224 Trademarks.................................................................................................................................... 224 Copyright Notice......................................................................................................................... 225 Copyright Attribution................................................................................................................ 225 Notations Used in This Guide Safety Symbols The projector and its manuals use graphical symbols and labels to indicate content that tells you how to use the projector safely. Read and carefully follow the instructions that are marked with these symbols and labels to avoid injury to persons or damage to property. This symbol indicates information that, if ignored, could possibly result in personal injury or even death. Warning This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling. Caution General Information Notations This label indicates procedures that may result in damage or injury if sufficient care is not taken. Attention This label indicates additional information that may be useful to know. [Button name] Indicates the name of the buttons on the remote control or the control panel. Example: [Esc] button Menu/Setting name Indicates projector menu and setting names. Example: Select the Image menu s Image > Advanced This label indicates links to the related pages. s This label indicates the projector's current menu level. Introduction to Your Projector Refer to these sections to learn more about your projector's features and part names. g Related Links • "Projector Features" p.9 • "Projector Parts and Functions" p.11 Projector Features 9

This projector comes with these special features. Refer to these sections for more details. g Related Links • "Long-life Laser Light Source" p.9 • "Quick and Easy Setup" p.9 • "Easy Wireless Projection" p.9 • "Projecting for Exhibitions" p.10 Long-life Laser Light Source A solid-state laser light source provides virtually maintenance-free operation until light source brightness is reduced. Quick and Easy Setup • Direct Power On feature to turn on the projector as soon as you plug it in. • Auto Power On feature to turn on the projector when the projector detects an image signal from the port you specified as the Auto Power On source. • Home screen feature to easily select an input source and useful functions. g Related Links • "Home Screen" p.36 • "Turning On the Projector" p.35 Easy Wireless Projection • Screen Mirroring to connect your projector and mobile device wirelessly using Miracast technology (EB‑L615U/EB‑L610U). • Epson iProjection (Windows/Mac) to project up to four images at the same time by splitting the projected screen. You can project images from computers on the network, or from smartphones or tablet devices. See the Epson iProjection Operation Guide (Windows/Mac) for details.

Projector Features 10

a • When projecting images using a wireless LAN, you must install the Epson 802.11b/g/n wireless LAN module, and then set up your projector and computer for wireless projection (EB‑L510U/EB‑L610W/EB‑L610/EB‑L400U/EB‑L500W/EB‑L500). Depending on your projector model, you may need to purchase the optional wireless LAN module. See the Quick Reference for a list of items supplied with your projector. • Some models have built-in wireless LAN modules (EB‑L615U/EB‑L610U). • You can download the necessary software and manuals from the following Web site: epson.com/ • Epson iProjection (iOS/Android) to connect your projector and mobile device wirelessly using the app available on the App Store or Google Play. a Any fees incurred when communicating with the App Store or Google Play are the responsibility of the customer. • Epson iProjection (Chromebook) to connect your projector and Chromebook device wirelessly using the app available on the Chrome Web Store. a Any fees incurred when communicating with the Chrome Web Store are the responsibility of the customer. g Related Links • "Using the Projector on a Network" p.104 Projecting for Exhibitions • A simple and neat design that fits perfectly into an exhibition space. • Content Playback mode to play your playlists, and add color and shape effects to your projected image. • Epson Projector Content Manager to prepare your playlists. See the Epson Projector Content Manager Operation Guide for details. a You can download the necessary software and manuals from the following Web site: epson.com/ g Related Links • "Projecting in Content Playback Mode" p.81

Projector Parts and Functions 11

The following sections explain the projector parts and their functions. All of the features in this guide are explained using illustrations of EB‑L615U unless otherwise mentioned. g Related Links • "Projector Parts - Front/Top" p.11 • "Projector Parts - Rear" p.12 • "Projector Parts - Base" p.13 • "Projector Parts - Interface Ports" p.13 • "Projector Parts - Control Panel" p.14 • "Projector Parts - Remote Control" p.15 Projector Parts - Front/Top EB‑L615U/EB‑L610U/EB‑L510U/EB‑L610W/EB‑L610 EB‑L400U/EB‑L500W/EB‑L500 Name Function A Air intake vent Takes in air to cool the projector internally. B Front adjustable foot When setup on a surface such as a desk, extend the foot to adjust the position of the image. C Focus ring Adjusts the image focus. D Zoom ring Adjusts the image size. E Projection lens Images are projected from here.

F Air intake vent (air filter) G Cable cover (EB‑L615U/EB‑L610U /EB‑L510U/EB‑L610 W/EB‑L610) Takes in air to cool the projector internally. Cover for the rear interface ports section.

H Indicators Indicates the projector's status. Projector Parts and Functions 12

Name Function Projector Parts - Rear

I Vertical lens shift dial (EB‑L615U/EB‑L610U /EB‑L510U/EB‑L610 W/EB‑L610) J Horizontal lens shift dial (EB‑L615U/EB‑L610U /EB‑L510U/EB‑L610 W/EB‑L610) Turn the dial to move the position of the projected image up or down. Turn the dial to move the position of the projected image left or right.

K Remote receiver Receives signals from the remote control. L Speaker Outputs audio. M Air exhaust vent Exhaust vent for air used to cool the projector internally. Caution While projecting, do not put your face or hands near the air exhaust vent, and do not place objects that may become warped or damaged by heat near the vent. Hot air from the air exhaust vent could cause burns, warping, or accidents to occur. N Remote receiver Receives signals from the remote control. g Related Links • "Projector Indicator Status" p.189 • "Remote Control Operation" p.33 • "Resizing the Image with the Zoom Ring" p.54 • "Focusing the Image Using the Focus Ring" p.55 • "Adjusting the Image Position Using Lens Shift" p.44 Name Function A Security slot The security slot is compatible with the Microsaver Security System manufactured by Kensington. B Power inlet Connects the power cord to the projector. C Interface ports Connects cables for external devices. D Control panel Operates the projector. E Remote receiver Receives signals from the remote control. g Related Links • "Installing a Security Cable" p.103 • "Projecting a PC Free Presentation" p.76

Projector Parts and Functions 13

Projector Parts - Base Name Function Name Function E Air filter cover screws Screws to fix the air filter cover in place. F Front adjustable foot When setup on a surface such as a desk, extend the foot to adjust the position of the image. g Related Links • "Installing a Security Cable" p.103 Projector Parts - Interface Ports

A Ceiling mount fixing points (four points) Attach the optional ceiling mount here when suspending the projector from a ceiling. Name Function A Computer1 port Inputs image signals from a computer and component

B Rear feet When setup on a surface such as a desk, turn to extend and retract to adjust the horizontal tilt. video signals from other video sources. B Audio 1 port Inputs audio from equipment connected to the

C Screw holes for cable cover (EB‑L615U/EB‑L610U /EB‑L510U/EB‑L610 W/EB‑L610) D Security cable attachment point Screw holes to fix the cable cover in place. Pass a commercially available wire lock through here and lock it in place. Computer1 port. C Audio 2 port Inputs audio from equipment connected to the Computer2 port. D Audio Out port Outputs audio from the current input source to an external speaker.

Projector Parts and Functions 14

Name Function E RS-232C port Connects an RS-232C cable to control the projector from a computer. (You do not need to use this port normally.) Projector Parts - Control Panel

F Computer2/Monitor Out port When Monitor Out Port is set to Monitor Out in the projector's Extended menu, analog RGB signals input from the Computer1 port are output to an external monitor. You cannot output signals input from other ports or component video signals. When Monitor Out Port is set to Computer2 in the projector's Extended menu, image signals from a computer and component video signals from other video sources are input. s Extended > Operation > Monitor Out Port

G Service port This port is used for batch settings. H USB-A port Connects a USB device and projects movies or images. Connects the optional document camera. Name Function A Power button Turns the projector on or off.

Connects the wireless LAN module (EB‑L510U/EB‑L610W/EB‑L610/EB‑L400U/EB‑L500W B [Source Search] button Changes to the next input source.

I Wireless LAN module fixing screw (EB‑L510U/EB‑L610 W/EB‑L610/EB‑L400 U/EB‑L500W/EB‑L50 0) /EB‑L500). Secures the wireless LAN module cover. C [A/V Mute] button Turns the video and audio on or off temporarily. D Left arrow button Displays the Control Panel Lock screen. Selects menu items while displaying the projector's menu or help. E Down arrow button Displays a test pattern. Selects menu items while displaying the projector's

J HDMI2 port Inputs video signals from HDMI compatible video equipment and computers. This projector is compatible with HDCP. K HDMI1 port menu or help. F [Enter] button [ ] Enters the current selection and moves to the next level while displaying the projector's menu or help.

L HDBaseT port (EB‑L615U/EB‑L610U /EB‑L510U/EB‑L610 W) Connects a LAN cable to the optional HDBaseT Transmitter. Optimizes Tracking, Sync., and Position in the projector's Signal menu while projecting an analog RGB signal from the Computer1 or Computer2 port. G Right arrow button Displays the Info menu.

M LAN port Connects a LAN cable to connect to a network. N Cable holder Pass a commercially available cable tie through here to secure cables. Selects menu items while displaying the projector's menu or help.

Projector Parts and Functions 15

Name Function H [Esc] button Stops the current function. Moves back to the previous menu level while displaying the projector's menu. I Up arrow button Displays the Geometry Correction menu. Selects menu items while displaying the projector's menu or help. J [Menu] button Displays and closes the projector's menu. g Related Links • "Selecting an Image Source" p.56 Projector Parts - Remote Control Name Function A Power button Turns the projector on or off.

Projector Parts and Functions 16

Name Function Name Function

B [Computer] button Switches the image source between the Computer1 and Computer2 ports. R [Volume] up/down buttons Adjusts the speaker volume.

C [HDMI] button Switches the image source between the HDMI1 and HDMI2 ports. Switches the image source from the HDBaseT input port (EB‑L615U/EB‑L610U/EB‑L510U/EB‑L610W). D Numeric buttons Enters numbers in the projector's menu while holding down the [Num] button. E [Auto] button Optimizes Tracking, Sync., and Position in the projector's Signal menu while projecting an analog RGB signal from the Computer1 or Computer2 port. F [Aspect] button Changes the aspect mode. G [Num] button Hold down this button to enter numbers using the numeric buttons. H [Menu] button Displays and closes the projector's menu. S [Pointer] button Displays the on-screen pointer. T [Esc] button Stops the current function. Moves back to the previous menu level while displaying the projector's menu. U [ID] button Hold down this button and press the numeric buttons to select the ID for the projector you want to operate using the remote control. V [Color Mode] button Changes the color mode. W [Link Menu] button Displays the settings menu for the device linked to the projector's HDMI ports. X [LAN] button Swithces the image source between the network connected devices. Y [USB] button Selects the USB-A port as the image source.

I Arrow buttons Selects menu items while displaying the projector's menu or help. J [Enter] button [ ] Enters the current selection and moves to the next level while displaying the projector's menu or help. K [User] button Performs settings assigned in the User Button setting in the projector's Settings menu. Z [Source Search] button a Remote control light emitting area Swithces to the next input source. Outputs remote control signals. L [Page] up/down buttons M [E-Zoom] +/– buttons Controls page up and down on your computer when you connect a projector and computer over the network. Displays the previous or next screen while using the PC Free feature. Zooms in or zooms out the image area. g Related Links • "Image Aspect Ratio" p.58 • "Color Mode" p.63 • "Input Signal Settings - Signal Menu" p.153 • "Projector Setup Settings - Extended Menu" p.158 • "Home Screen" p.36 • "Projecting Two Images Simultaneously" p.73

N [A/V Mute] button Turns the video and audio on or off temporarily. O [Split] button Projects two images from different image sources simultaneously by splitting the projected screen. P [Home] button Displays and closes the Home screen. Q [Freeze] button Pauses or resumes images. • "Using the Remote Control as a Pointer" p.88 • "Projecting a PC Free Presentation" p.76 • "Using the Projector on a Network" p.104

Setting Up the Projector Follow the instructions in these sections to set up your projector. g Related Links • "Projector Placement" p.18 • "Projector Connections" p.22 • "Attaching and Removing the Cable Cover" p.30 • "Attaching the Zoom Ring Locks" p.31 • "Installing Batteries in the Remote Control" p.32 Projector Placement 18

You can place the projector on almost any flat surface to project an image. You can also install the projector in a ceiling mount if you want to use it in a fixed location. An optional ceiling mount is required when suspending the projector from a ceiling. Note the following points when selecting a projector location: • Place the projector on a sturdy, level surface or install it using a compatible mount. • Leave plenty of space around and under the projector for ventilation, and do not place it on top of or next to anything that could block the vents. • Place the projector parallel to the screen. Warning • You must install a ceiling mount when suspending the projector from a ceiling. If you do not install the projector correctly, it could fall and cause damage or injury. • Do not use adhesives on the ceiling mount fixing points to prevent the screws from loosening, or use lubricants, oils, or similar substances on the projector; the projector case may crack causing it to fall from its ceiling mount. This could cause serious injury to anyone under the ceiling mount and could damage the projector. • Do not cover the projector's air intake or air exhaust vents. If the vents are covered, the internal temperature could rise and cause a fire. • Do not install the projector on an unstable surface or in a location beyond the weight specifications of the projector. Otherwise, it could fall or topple causing an accident and injury. • When installing the projector in a high position, take measures to prevent falling by using wires to ensure safety in an emergency, such as an earthquake, and to prevent accidents. If it is not installed correctly, it could fall causing an accident and injury. Attention • If you are using the projector at altitudes above 1500 m, set the High Altitude Mode setting to On in the projector's Extended menu to ensure the projector's internal temperature is regulated properly. s Extended > Operation > High Altitude Mode • Try not to setup the projector in locations subject to high humidity and dust, or in locations subject to smoke from fires or tobacco smoke. g Related Links • "Projector Setup and Installation Options" p.19 • "Projection Distance" p.20 • "Image Shape" p.49 • "Projector Setup Settings - Extended Menu" p.158

Projector Placement 19

Projector Setup and Installation Options You can set up or install your projector in the following ways: Front/Rear Front Ceiling/Rear Ceiling If you project from the ceiling or from the rear, select the correct Projection setting and, if necessary, turn on the Inv Direction Button setting and adjust the OSD Rotation setting. g Related Links • "Precautions on Installation" p.19 • "Projection Modes" p.41 Precautions on Installation You can install the projector or mount it to the ceiling at any horizontal or vertical angle. Note the following precautions when installing the projector. Attention • If the projector is installed at an angle, it should be installed by qualified technicians using mounting hardware designed for use with this projector. • Install the projector appropriately to prevent it from falling down. • Use M4 screws (up to a depth of 9 mm) to fix the projector's ceiling mount fixing points and the mounting hardware at four points.

Projector Placement 20

Installation space Attention Be sure to leave the following amount of space around the projector so as not to block the air exhaust and intake vents. A 10 cm B 20 cm C 40 cm Installation space (When installing multiple projectors side by side) Attention • If you are installing multiple projectors next to each other, make sure hot air from the exhaust vent does not go into the air intake vent of another projector. A 150 cm • If you use a partition, you can narrow the space between the projectors. A 20 cm B 40 cm * Partition Projection Distance The distance at which you place the projector from the screen determines the approximate size of the image. The image size increases the farther the projector is from the screen, but can vary depending on the zoom factor, aspect ratio, and other settings.

Projector Placement 21 See the Appendix for details about how far to place the projector from the screen based on the size of the projected image. g Related Links • "Screen Size and Projection Distance" p.207 Projector Connections 22

See these sections to connect the projector to a variety of projection sources. Attention Check the shape and orientation of the connectors on any cable you plan to connect. Do not force a connector into a port if it does not fit. The device or your projector could be damaged or could malfunction. a See the Quick Reference for a list of cables supplied with your projector. Purchase optional or commercially available cables when necessary. g Related Links • "Connecting to a Computer" p.22 • "Connecting to Video Sources" p.23 • "Connecting to External USB Devices" p.25 • "Connecting to a Document Camera" p.26 • "Connecting to an HDBaseT Transmitter" p.27 • "Connecting to External Output Devices" p.27 Connecting to a Computer Follow the instructions in these sections to connect a computer to the projector. g Related Links • "Connecting to a Computer for VGA Video and Audio" p.22 • "Connecting to a Computer for HDMI Video and Audio" p.23 Connecting to a Computer for VGA Video and Audio You can connect the projector to your computer using a VGA computer cable. You can play sound through the projector's speaker system by connecting a commercially available 3.5 mm stereo mini-jack audio cable. a • To connect a computer that does not have a VGA video port, you need an adapter that allows you to connect to the projector's VGA video port. • To project an image source connected to the Computer2/Monitor Out port, set Monitor Out Port to Computer2 in the projector's Extended menu. s Extended > Operation > Monitor Out Port • You can also set the port used for audio input in the projector's Extended menu. s Extended > A/V Settings > Audio Settings > Audio Output • Make sure the audio cable is labeled "No resistance". a Connect the VGA computer cable to your computer's monitor port. b Connect the other end to a Computer port on the projector. c Tighten the screws on the VGA connector. d Connect the audio cable to your laptop's headphone or audio-out jack, or your desktop's speaker or audio-out port.

Projector Connections 23

e Connect the other end to the Audio port that corresponds to the Computer port you are using. g Related Links • "Projector Setup Settings - Extended Menu" p.158 Connecting to a Computer for HDMI Video and Audio If your computer has an HDMI port, you can connect it to the projector using an HDMI cable and send the computer's audio with the projected image. a To connect a Mac that does not have an HDMI port, you need an adapter that allows you to connect to the projector's HDMI port. Contact Apple for compatible adapter options. Older Mac computers (2009 and earlier) may not support audio through the HDMI port. a Connect the HDMI cable to your computer's HDMI output port. b Connect the other end to the projector's HDMI port. a If you have problems hearing audio through the HDMI connection, connect one end of a commercially available 3.5 mm stereo mini-jack audio cable to the projector's Audio port and the other end to your computer's audio out port. Select the audio input port you connected to in the projector's Extended menu. s Extended > A/V Settings > Audio Settings > HDMI1 Audio Output s Extended > A/V Settings > Audio Settings > HDMI2 Audio Output g Related Links • "Projector Setup Settings - Extended Menu" p.158 Connecting to Video Sources Follow the instructions in these sections to connect video devices to the projector.

Projector Connections 24

a • If the port on the device you connect has an unusual shape, use the cable supplied with the device or an optional cable to connect to the projector. • The cable differs depending on the output signal from the connected video devices. • Some video devices are capable of outputting different types of signals. See your video device manual to confirm what type of signals can be output. • If audio is not output correctly, check the settings in Audio Out Device. s Settings > HDMI Link > Audio Out Device g Related Links • "Connecting to an HDMI Video Source" p.24 • "Connecting to a Component-to-VGA Video Source" p.24 Connecting to an HDMI Video Source If your video source has an HDMI port, you can connect it to the projector using an HDMI cable and send the image source's audio with the projected image. Attention Do not turn on the video source before connecting it to the projector. Doing so could damage the projector. a Connect the HDMI cable to your video source's HDMI output port. b Connect the other end to the projector's HDMI port. a If you have problems hearing audio through the HDMI connection, connect one end of a commercially available 3.5 mm stereo mini-jack audio cable to the projector's Audio port and the other end to your video source's audio out port. Select the audio input port you connected to in the projector's Extended menu. s Extended > A/V Settings > Audio Settings > HDMI1 Audio Output s Extended > A/V Settings > Audio Settings > HDMI2 Audio Output g Related Links • "Projector Setup Settings - Extended Menu" p.158 Connecting to a Component-to-VGA Video Source If your video source has component video ports, you can connect it to the projector using a component-to-VGA video cable. Depending on your component ports, you may need to use an adapter cable along with a component video cable. You can play sound through the projector's speaker system by connecting a stereo mini-jack audio cable.

Projector Connections 25

a • To project an image source connected to the Computer2/Monitor Out port, set Monitor Out Port to Computer2 in the projector's Extended menu. s Extended > Operation > Monitor Out Port • You can also set the port used for audio input in the projector's Extended menu. s Extended > A/V Settings > Audio Settings > Audio Output • Make sure the audio cable is labeled "No resistance". a Connect the component connectors to your video source's color-coded component video output ports. a The ports usually labeled Y, Pb, Pr or Y, Cb, Cr. If you are using an adapter, connect these connectors to your component video cable. b Connect the VGA connector to a Computer port on the projector. c Tighten the screws on the VGA connector. d Connect the audio cable to your video source's audio-out ports. e Connect the other end to the projector's Audio port. If your image colors appear incorrectly, you may need to change the Input Signal setting in the projector's Signal menu. s Signal > Advanced > Input Signal g Related Links • "Input Signal Settings - Signal Menu" p.153 • "Projector Setup Settings - Extended Menu" p.158 Connecting to External USB Devices Follow the instructions in these sections to connect external USB devices to the projector. g Related Links • "USB Device Projection" p.25 • "Connecting to a USB Device" p.26 • "Disconnecting a USB Device" p.26 USB Device Projection You can project images and other content without using a computer or video device by connecting any of these devices to your projector: • USB flash drive

Projector Connections 26

• Digital camera or smartphone • USB hard drive • Multimedia storage viewer a • Digital cameras or smartphones must be USB-mounted devices, not TWAIN-compliant devices, and must be USB Mass Storage Class compliant. • USB hard drives must meet these requirements: • USB Mass Storage Class-compliant (not all USB Mass Storage Class devices are supported) • Formatted in FAT16/32 • Self-powered by their own AC power supplies (bus-powered hard drives are not recommended) • Avoid using hard drives with multiple partitions You can project slide shows from image files on a connected USB device. g Related Links • "Projecting a PC Free Presentation" p.76 Connecting to a USB Device You can connect your USB device to the projector's USB-A port and use it to project images and other content. a If your USB device came with a power adapter, plug the device into an electrical outlet. b Connect the USB cable or USB flash drive to the projector's USB-A port as shown. Attention • Use the USB cable supplied with or specified for use with the device. • Do not connect a USB hub or a USB cable longer than 3 meters, or the device may not operate correctly. c Connect the other end to your device, if necessary. Disconnecting a USB Device When you have finished presenting with a connected USB device, disconnect the device from the projector. a Turn off and unplug the device, if necessary. b Disconnect the USB device from the projector. Connecting to a Document Camera You can connect a document camera to your projector to project images viewed by the camera.

Projector Connections 27

The connection method varies depending on your Epson document camera model. See the document camera manual for details. Connecting to an HDBaseT Transmitter To send an HDMI or RS-232C signal over a long distance, you can connect the projector to an optional HDBaseT transmitter using a 100Base-TX network cable (EB‑L615U/EB‑L610U/EB‑L510U/EB‑L610W). This is useful when you want to send a signal to or control the projector from a remote location, such as in a hall or event site, since you can use a network cable up to 100 m in length. To ensure proper data transmission, use a Category 5e STP cable or better. However, operation is not guaranteed for all input/output devices and environments. a • To enable communication from the Ethernet and serial ports on the transmitter, select On as the Control Communications setting in the projector's Extended menu (Standby Mode is automatically set to Communication On). Turning on this setting disables the projector's LAN and RS-232C ports. s Extended > HDBaseT > Control Communications s Extended > Standby Mode > Standby Mode • If you connected an Extron XTP transmitter or switcher to the projector's HDBaseT port, select On as the Extron XTP setting in the projector's Extended menu (Control Communications is automatically set to On, and Standby Mode is automatically set to Communication On). s Extended > HDBaseT > Extron XTP s Extended > Standby Mode > Standby Mode • Wired remote control using the HDBaseT port is not available. a Turn off the projector and HDBaseT transmitter. a Make sure the projector and HDBaseT transmitter are turned off when connecting or disconnecting a network cable between the two devices. b Connect one end of the network cable to the HDBaseT port on the transmitter. c Connect the other end to the projector's HDBaseT port. a See the documentation that came with the HDBaseT transmitter for instructions on connecting it to your video device or computer. d Turn on the projector and HDBaseT transmitter. g Related Links • "Projector Setup Settings - Extended Menu" p.158 Connecting to External Output Devices Follow the instructions in these sections to connect external devices to the projector. g Related Links • "Connecting to a VGA Monitor" p.28 • "Connecting to External Speakers" p.28

Projector Connections 28

Connecting to a VGA Monitor If you connected the projector to a computer using a Computer port, you can also connect an external monitor to the projector. This lets you see your presentation on the external monitor even when the projected image is not visible. a • If you want to output images to an external monitor when the projector is turned off, select Always On as the A/V Output setting in the projector's Extended menu. s Extended > A/V Settings > A/V Output • To output images to an external monitor, set Monitor Out Port to Monitor Out in the projector's Extended menu. s Extended > Operation > Monitor Out Port • Monitors that use a refresh rate of less than 60 Hz may not be able to display images correctly. a Make sure your computer is connected to the projector's Computer port. a • If there are two computer ports, make sure you use the Computer1 port. • Only analog RGB signals from the Computer1 port can be output to an external monitor. You cannot output signals input from other ports or component video signals. b Connect the external monitor's cable to your projector's Monitor Out port. g Related Links • "Projector Setup Settings - Extended Menu" p.158 Connecting to External Speakers To enhance the sound from your presentation, you can connect the projector to external self-powered speakers. You can control the volume using the projector's remote control. To output audio from external speakers, select Projector as the Audio Out Device setting in the projector's Settings menu. When an audio/video system is not connected to the projector, audio is output from the external speakers even if Audio Out Device is set to AV System. s Settings > HDMI Link > Audio Out Device a • If you want to output audio from the external speakers when the projector is turned off, select Always On as the A/V Output setting in the projector's Extended menu. s Extended > A/V Settings > A/V Output • You can also connect the projector to an amplifier with speakers. • The projector's built-in speaker system is disabled when you connect external speakers.

Projector Connections 29 a Make sure your computer or video source is connected to the projector with both audio and video cables as necessary. b Locate the appropriate cable to connect your external speakers, such as a stereo mini-jack-to-pin-jack cable, or another type of cable or adapter. c Connect one end of the cable to your external speakers as necessary. d Connect the stereo mini-jack end of the cable to your projector's Audio Out port. g Related Links • "Projector Setup Settings - Extended Menu" p.158 Attaching and Removing the Cable Cover 30

When suspending the projector from a ceiling, you can attach the cable cover that came with your projector to hide the attached cables from view (EB‑L615U/EB‑L610U/EB‑L510U/EB‑L610W/EB‑L610). a Pass a commercially available cable tie through the cable holder and tie the cables together. Caution Do not bundle the power cord to the other cables. Otherwise, a fire may occur. b Place the cable cover on the projector as shown, guiding the cables through the notch on the base of the cable cover. c Tighten the cable cover screws. To remove the cover, loosen the cover screws and pull the cover off of the projector.

Attaching the Zoom Ring Locks 31 Make sure you attach the zoom ring locks that come with the projector to prevent the zoom ring from moving unexpectedly after adjusting the projected image (EB‑L500W/EB‑L500). Installing Batteries in the Remote Control 32

The remote control uses the two AA batteries that came with the projector. Attention Make sure you read the Safety Instructions before handling the batteries. a Remove the battery cover as shown. b Remove the old batteries, if necessary. a Dispose of used batteries according to local regulations. c Insert the batteries with the + and – ends facing as shown. Warning Check the positions of the (+) and (–) marks inside the battery holder to ensure the batteries are inserted the correct way. If the batteries are not used correctly, they could explode or leak causing a fire, injury, or damage to the product. d Replace the battery cover and press it down until it clicks into place.

Installing Batteries in the Remote Control 33 g Related Links • "Remote Control Operation" p.33 Remote Control Operation The remote control lets you control the projector from almost anywhere in the room. Make sure that you aim the remote control at the projector's receivers within the distance and angles listed here. a Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you are not going to use the remote control for a long time, remove the batteries. Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features. g Related Links • "Turning On the Projector" p.35 • "Turning Off the Projector" p.37 • "Setting the Date and Time" p.38 • "Selecting the Language for the Projector Menus" p.40 • "Projection Modes" p.41 • "Setting the Screen Type" p.42 • "Adjusting the Image Position Using Lens Shift" p.44 • "Displaying a Test Pattern" p.46 • "Adjusting the Image Height" p.48 • "Image Shape" p.49 • "Resizing the Image with the Zoom Ring" p.54 • "Focusing the Image Using the Focus Ring" p.55 • "Selecting an Image Source" p.56 • "Image Aspect Ratio" p.58 • "Color Mode" p.63 • "Adjusting the Image Color" p.65 • "Adjusting the Brightness" p.68 • "Controlling the Volume with the Volume Buttons" p.71 Turning On the Projector 35

Turn on the computer or video equipment you want to use after you turn on the projector. a Connect the power cord to the projector's power inlet and plug it into an electrical outlet. The projector's power indicator turns blue. This indicates that the projector is receiving power, but is not yet turned on (it is in standby mode). b Press the power button on the control panel or remote control to turn on the projector. The projector beeps and the status indicator flashes blue as the projector warms up. Once the projector is warmed up, the status indicator stops flashing and turns blue. a • When Quick Startup is enabled in the projector's Extended menu, the projector becomes ready for use in several seconds the next time you press the power button. s Extended > Operation > Quick Startup Try the following if you do not see a projected image. • Turn on the connected computer or video device. • Change the screen output from the computer when using a laptop computer. • Insert a DVD or other video media, and press play (if necessary). • Press the [Source Search] button on the control panel or remote control to detect the source. • Press the button for the desired video source on the remote control. • If the Home screen is displayed, select the source you want to project. Warning • Never look into the projector lens when the light source is on. This can damage your eyes and is especially dangerous for children. • When turning on the projector at a distance using the remote control, make sure there is no one looking into the lens. • During projection, do not block the light from the projector with a book or other objects. If the light from the projector is blocked, the area on which the light shines becomes hot which could cause it to melt, burn, or start a fire. Also, the lens may get hot due to the reflected light which could cause the projector to malfunction. To stop projection, use the A/V Mute function, or turn off the projector. a • When the Direct Power On setting is set to On in the projector's Extended menu, the projector turns on as soon as you plug it in. Note that the projector also turns on automatically in cases such as recovery from a power outage. s Extended > Operation > Direct Power On • If you select a specific port as the Auto Power On setting in the projector's Extended menu, the projector turns on as soon as it detects a signal or cable connection from that port. s Extended > Operation > Auto Power On g Related Links • "Home Screen" p.36 • "Projector Setup Settings - Extended Menu" p.158

Turning On the Projector 36

Home Screen The Home screen feature allows you to easily select an image source and access useful functions. You can display the Home screen by pressing the [Home] button on the remote control. The Home screen is also displayed when you turn on the projector and no signal is being input. Press the arrow buttons on the control panel or remote control to select a menu item, and then press [Enter]. A Selects the source you want to project. B Displays the Connection Guide. You can select the wireless connection methods according to the devices you are using, such as smartphones or computers. C Indicates the projector is in Content Playback mode. D Displays the Help screen. E Displays the projector's menu. F Performs menu options assigned to Home Screen in the projector's Extended menu. G Selects the brightness for the light source. H Changes the projector's color mode. a The Home screen disappears after 10 minutes of inactivity. g Related Links • "Image Shape" p.49 • "Projector Setup Settings - Extended Menu" p.158 • "Using a QR Code to Connect a Mobile Device" p.114 • "Using the Projector's Menus" p.149 • "Using the Projector Help Displays" p.192 • "Projecting Two Images Simultaneously" p.73

Turning Off the Projector 37 Turn off the projector after use. a • Turn off this product when it is not in use to prolong the life of the projector. Light source life varies depending on the mode selected, environmental conditions, and usage. Brightness decreases over time. • Automatic light source calibration starts periodically when you turn off the projector. However, this does not start automatically in the following situations: • If you use the projector continuously for more than 24 hours in the Constant Brightness mode • If you regularly turn off the projector by shutting off the power outlet (direct shutdown) Schedule periodic Light Source Calibration events in the projector's Extended menu. s Extended > Schedule Settings • Since the projector supports the direct shutdown feature, it can be turned off directly using the breaker. a Press the power button on the control panel or remote control. The projector displays a shutdown confirmation screen. b Press the power button again. (To leave it on, press any other button.) The projector beeps twice, the light source turns off, and the status indicator turns off. c To transport or store the projector, make sure the power indicator is blue (but not flashing) and the status indicator is off, then unplug the power cord. Setting the Date and Time 38

You can set the date and time for the projector. a Turn on the projector. b Press the [Menu] button on the control panel or remote control. c Select the Extended menu and press [Enter]. d Select the Operation setting and press [Enter]. e Select the Date & Time setting and press [Enter]. You see this screen: f Select the Date & Time setting and press [Enter]. You see this screen: g Select Date, press [Enter], and use the displayed keyboard to enter today's date. h Select Time, press [Enter], and use the displayed keyboard to enter the current time. i Select Time Difference (UTC), press [Enter], and set the time difference from Coordinated Universal Time. j When you are finished, select Set and press [Enter]. k To activate daylight saving time, select the Daylight Saving Time setting and press [Enter]. Then select settings. l When you are finished, select Set and press [Enter].

Setting the Date and Time 39 m To update the time automatically through an Internet time server, select the Internet Time setting and press [Enter]. Then select settings. n When you are finished, select Set and press [Enter]. o Press [Menu] or [Esc] to exit the menus. Selecting the Language for the Projector Menus 40 If you want to view the projector's menus and messages in another language, you can change the Language setting. a Turn on the projector. b Press the [Menu] button on the control panel or remote control. c Select the Extended menu and press [Enter]. d Select the Language setting and press [Enter]. e Select the language you want to use and press [Enter]. f Press [Menu] or [Esc] to exit the menus. Projection Modes 41

Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly. • Front (default setting) lets you project from a table in front of the screen. • Front/Ceiling flips the image over top-to-bottom to project upside-down from a ceiling or wall mount. • Rear flips the image horizontally to project from behind a translucent screen. • Rear/Ceiling flips the image over top-to-bottom and horizontally to project from a ceiling or wall mount and behind a translucent screen. g Related Links • "Changing the Projection Mode Using the Menus" p.41 • "Projector Setup and Installation Options" p.19 Changing the Projection Mode Using the Menus You can change the projection mode to flip the image over top-to-bottom and/or left-to-right using the projector menus. a Turn on the projector and display an image. b Press the [Menu] button on the control panel or remote control. c Select the Extended menu and press [Enter]. d Select Projection and press [Enter]. e Select a projection mode and press [Enter]. f Press [Menu] or [Esc] to exit the menus.

Setting the Screen Type 42

You can use the Screen Type setting to match the aspect ratio of the displayed image to the screen you are using. a This setting is unavailable when using one of the following input sources: • USB • LAN a Turn on the projector and display an image. b Press the [Menu] button on the control panel or remote control. c Select the Extended menu and press [Enter]. d Select Display > Screen > Screen Type. You see this screen: e Select your screen's aspect ratio and press [Enter]. f Press [Menu] to exit the menus. g Adjust the aspect ratio for the projected image, if necessary. g Related Links • "Adjusting the Image Position Using Screen Position" p.42 Adjusting the Image Position Using Screen Position You can adjust the image position if there are margins between the edge of the image and the projected screen frame. a • You cannot adjust the screen position if the Screen Type setting is set to 16:10 for a WXGA/WUXGA projector model or 4:3 for a XGA projector model. a Turn on the projector and display an image. b Press the [Menu] button on the control panel or remote control.

Setting the Screen Type 43 c Select the Extended menu and press [Enter]. d Select Display > Screen > Screen Position. e Use the arrow buttons on the control panel or remote control to adjust the position of the image. f When you are finished, press [Menu]. Adjusting the Image Position Using Lens Shift 44

If you cannot install the projector directly in front of the screen, you can adjust the position of the projected image using the lens shift feature (EB‑L615U/EB‑L610U/EB‑L510U/EB‑L610W/EB‑L610). a • Wait 20 minutes after turning on the projector before setting the focus, zoom, and lens shift for maximum accuracy. • Keep the vertical and horizontal lens shift dials in their center positions for the clearest picture. a Turn on the projector and display an image. b Turn the vertical and horizontal lens shift dials on the projector to adjust the position of the projected image as necessary. • EB‑L615U/EB‑L610U/EB‑L510U/EB‑L610W A Center of lens B Projected image when the lens is set to the home position C Maximum range: V × 50%

Adjusting the Image Position Using Lens Shift 45 D When the horizontal direction is at the maximum value: V × 12% • EB‑L610 A Center of lens B Projected image when the lens is set to the home position C Maximum range: V × 50% D When the horizontal direction is at the maximum value: V × 5% a You cannot move the image horizontally when the lens is shifted vertically all the way. Displaying a Test Pattern 46

You can display a test pattern to adjust the projected image without connecting a computer or video device. a The test pattern's shape is determined by the Screen Type setting. Be sure to set the correct screen type before adjusting with the test pattern. s Extended > Display > Screen > Screen Type a Turn on the projector. b Press the down arrow button on the control panel. a You can also display the Test Pattern setting in the projector's Settings menu. The test pattern is displayed. c Press the down arrow button on the control panel again, and then press [Enter] to display the pattern you want. d While the pattern is displayed, press the left or right arrow button on the remote control or press [Enter] to cycle through the available test patterns. e Adjust the image as necessary. f Press [Esc] to clear the test pattern. g Related Links • "Available Test Pattern Image Adjustments" p.46 Available Test Pattern Image Adjustments You can adjust the following settings while the test pattern is displayed.

Displaying a Test Pattern 47 Menu Settings Image Color Mode White Balance Advanced • Gamma * • RGBCMY ** Settings Geometry Correction Extended Multi-Projection a To set menu items that cannot be set while the test pattern is being displayed or to fine-tune the projected image, project an image from the connected device. * Except for custom Gamma settings ** Except for the Color Uniformity setting Adjusting the Image Height 48

If you are projecting from a table or other flat surface and the image is too high or low, you can adjust the image height using the projector's adjustable feet. The larger the angle of tilt, the harder it becomes to focus. Locate the projector so that it only needs to be tilted at a small angle. a Turn on the projector and display an image. b To adjust the image height, rotate the front foot to extend or retract it. A Extend the front foot B Retract the front foot c If the image is tilted, rotate the rear feet to adjust their height. A Extend the rear foot B Retract the rear foot If the projected image is unevenly rectangular, you need to adjust the image shape. g Related Links • "Image Shape" p.49

Image Shape 49

You can project an even, rectangular image by placing the projector directly in front of the center of the screen and keeping it level. If you place the projector at an angle to the screen, or tilt it up or down, or off to the side, you may need to correct the image shape. g Related Links • "Correcting Image Shape with H/V Keystone" p.49 • "Correcting the Image Shape with Quick Corner" p.51 • "Correcting Image Shape with Arc Correction" p.52 Correcting Image Shape with H/V Keystone You can use the projector's H/V-Keystone setting to correct the shape of an image that is unevenly rectangular on the sides. a You cannot combine H/V-Keystone correction with other image shape correction methods. a Turn on the projector and display an image. b Press the [Menu] button on the control panel or remote control. c Select the Settings menu and press [Enter]. d Select Geometry Correction and press [Enter]. a You can also access the Geometry Correction screen by pressing the up arrow button on the control panel. e Select H/V-Keystone and press [Enter]. Then press [Enter] again. You see the H/V-Keystone adjustment screen:

Image Shape 50

f Use the arrow buttons on the projector or the remote control to select between vertical and horizontal keystone correction and to adjust the image shape as necessary. • V-Keystone • H-Keystone a If you have adjusted the position of the projected image by using the lens shift feature, adjust the V-Balance and H-Balance settings as necessary (EB-L615U/EB-L610U/EB-L510U/EB L610W/EB-L610). • V-Balance • H-Balance g When you are finished, press [Esc]. After correction, your image is slightly smaller. g Related Links • "Projector Feature Settings - Settings Menu" p.155

Image Shape 51

Correcting the Image Shape with Quick Corner You can use the projector's Quick Corner setting to correct the shape and size of an image that is unevenly rectangular. a Turn on the projector and display an image. b Press the [Menu] button on the control panel or remote control. c Select the Settings menu and press [Enter]. e Select Quick Corner and press [Enter]. Then press [Enter] again if necessary. You see the area selection screen. f Use the arrow buttons to select the corner of the image you want to adjust. Then press [Enter]. a To reset the Quick Corner corrections, hold down [Esc] for about two seconds while the area selection screen is displayed, and then select Yes. g Press the arrow buttons to adjust the image shape as necessary. To return to the area selection screen, press [Enter].

d Select Geometry Correction and press [Enter]. Image Shape 52

a • If you see this screen, you cannot adjust the shape any further in the direction indicated by the gray triangle. h Repeat steps 6 and 7 as needed to adjust any remaining corners. i When you are finished, press [Esc]. g Related Links • "Projector Feature Settings - Settings Menu" p.155 Correcting Image Shape with Arc Correction You can use the projector's Arc Correction setting to adjust the shape of an image projected on a curved or spherical surface. a Turn on the projector and display an image. b Press the [Menu] button on the control panel or remote control. c Select the Settings menu and press [Enter]. d Select Geometry Correction and press [Enter].

Image Shape 53

e Select Arc Correction and press [Enter]. You see the area selection screen. f Use the arrow buttons to select the area of the image you want to adjust, then press [Enter]. a To reset the Arc Correction settings, hold down [Esc] for about two seconds while the area selection screen is displayed, and then select Yes. g Press the arrow buttons to adjust the image shape of the selected area as necessary. To return to the area selection screen, press [Enter]. a If you see this screen, you cannot adjust the shape any further in the direction indicated by the gray triangle. h Repeat steps 7 and 8 as needed to adjust any remaining areas. i When you are finished, press [Esc].

Resizing the Image with the Zoom Ring 54 You can resize the image using the projector's zoom ring. a Wait 20 minutes after turning on the projector before setting the focus, zoom, and lens shift for maximum accuracy. a Turn on the projector and display an image. b Rotate the zoom ring to enlarge or reduce the image. Focusing the Image Using the Focus Ring 55 You can correct the focus using the focus ring. a Wait 20 minutes after turning on the projector before setting the focus, zoom, and lens shift for maximum accuracy. Selecting an Image Source 56

When multiple image sources are connected to the projector, such as a computer and DVD player, you can switch from one image source to the other. a Make sure the connected image source you want to use is turned on. b For video image sources, insert a DVD or other video media and press play. c Do one of the following: • Press the [Source Search] button on the control panel or remote control until you see the image from the source you want. a This screen is displayed when no image signal is detected. Check the cable connections between the projector and image source. • Press the button for the source you want on the remote control. If there is more than one port for that source, press the button again to cycle through the sources. • Press the [Home] button on the remote control.

Selecting an Image Source 57 Then select the source you want to use from the screen displayed. a • HDBaseT is available only with the EB‑L615U/EB‑L610U/EB‑L510U/EB‑L610W. • Screen Mirroring is available only with the EB‑L615U/EB‑L610U. g Related Links • "Projector Parts - Control Panel" p.14 Image Aspect Ratio 58

The projector can display images in different width-to-height ratios called aspect ratios. Normally, the input signal from your video source determines the image's aspect ratio. However, you can change the aspect ratio for certain images to fit your screen. If you always want to use a particular aspect ratio for a certain video input source, you can select it using the projector's Signal menu. g Related Links • "Changing the Image Aspect Ratio" p.58 • "Available Image Aspect Ratios" p.58 • "Projected Image Appearance with Each Aspect Mode" p.59 • "Input Signal Settings - Signal Menu" p.153 Changing the Image Aspect Ratio You can change the aspect ratio of the displayed image. a • Set the Screen Type setting in the projector's Extended menu before changing the aspect ratio. s Extended > Display > Screen > Screen Type • This setting is available only when the Scale Mode setting is set to Full Display. s Signal > Scale > Scale Mode a Turn on the projector and switch to the image source you want to use. b Press the [Aspect] button on the remote control. The shape and size of the displayed image changes, and the name of the aspect ratio appears briefly on the screen. c To cycle through the available aspect ratios for your input signal, press the [Aspect] button repeatedly. a To display images without black bars, set Resolution to Wide or Normal in the projector’s Signal menu according to the computer’s resolution. g Related Links • "Input Signal Settings - Signal Menu" p.153 Available Image Aspect Ratios You can select the following image aspect ratios, depending on the selected Screen Type setting and the input signal from your image source. a • The available aspect ratio setting varies depending on the input signal. • Note that using the aspect ratio function of the projector to reduce, enlarge, or split the projected image for commercial purposes or for public viewing may infringe upon the rights of the copyright holder of that image based on copyright law. Aspect mode Description Auto Automatically sets the aspect ratio according to the input signal and the Resolution setting. Normal Displays images using the full projection area and maintains the aspect ratio of the image. 4:3 Converts the aspect ratio of the image to 4:3. 16:9 Converts the aspect ratio of the image to 16:9.

Image Aspect Ratio 59

Aspect mode Description Full Displays images using the full size of the projection area, but does not maintain the aspect ratio. Aspect mode Aspect ratio for input signals 16:10 16:9 4:3 16:9

H-Zoom V-Zoom Displays images using the full width (H-Zoom) or full height (V-Zoom) of the projection area and maintains the aspect ratio of the image. Areas that exceed the edges of the projected screen are not projected.

Native Displays images as is (aspect ratio and resolution are maintained). Areas that exceed the edges of the projected screen are not projected. Projected Image Appearance with Each Aspect Mode Black bands and cropped images may project in certain aspect ratios, depending on the aspect ratio and resolution of your input signal. See the following table to confirm the position of black bands and cropped images. a The image for Native varies depending on the input signal. EB‑L615U/EB‑L610U/EB‑L510U/EB‑L610W/EB‑L400U/EB‑L500W Screen type setting: 16:10 Aspect mode Aspect ratio for input signals 16:10 16:9 4:3 Normal Auto Full H-Zoom V-Zoom Native Screen type setting: 16:9 Aspect mode Aspect ratio for input signals 16:10 16:9 4:3 Normal Auto

Image Aspect Ratio 60

Aspect mode Aspect ratio for input signals 16:10 16:9 4:3 Full H-Zoom V-Zoom Native Screen type setting: 4:3 Aspect mode Aspect ratio for input signals 16:10 16:9 4:3 Normal Auto 4:3 * Aspect mode Aspect ratio for input signals 16:10 16:9 4:3 16:9 H-Zoom V-Zoom Native ** * When inputting an HDTV signal (720p/1080i/1080p), the aspect ratio of the signal is maintained, while the image is trimmed on the left and right and displayed. ** Only computer images and images from the HDMI ports or the HDBaseT port. The image may differ depending on the resolution of the input signal.

Image Aspect Ratio 61

EB‑L610/EB‑L500 Screen type setting: 4:3 Aspect mode Aspect ratio for input signals 16:10 16:9 4:3 Normal Auto 4:3 * 16:9 H-Zoom V-Zoom Native ** * When inputting an HDTV signal (720p/1080i/1080p), the aspect ratio of the signal is maintained, while the image is trimmed on the left and right and displayed. ** Only computer images and images from the HDMI ports or the HDBaseT port. The image may differ depending on the resolution of the input signal. Screen type setting: 16:9 Aspect mode Aspect ratio for input signals 16:10 16:9 4:3 Normal Auto Full H-Zoom V-Zoom Native

Image Aspect Ratio 62 Screen type setting: 16:10 Aspect mode Aspect ratio for input signals 16:10 16:9 4:3 Normal Auto 16:9 Full H-Zoom V-Zoom Native Color Mode 63

The projector offers different color modes to provide optimum brightness, contrast, and color for a variety of viewing environments and image types. You can select the mode designed to match your image and environment, or experiment with the available modes. g Related Links • "Changing the Color Mode" p.63 • "Available Color Modes" p.63 • "Turning On Automatic Luminance Adjustment" p.63 Changing the Color Mode You can change the projector's Color Mode using the remote control to optimize the image for your viewing environment. a Turn on the projector and switch to the image source you want to use. b Press the [Color Mode] button on the remote control to change the Color Mode. The name of the Color Mode appears briefly on the screen and then image appearance changes. c To cycle through all of the available color modes for your input signal, press the [Color Mode] button repeatedly. a You can also set the Color Mode setting in the projector's Image menu. g Related Links • "Image Quality Settings - Image Menu" p.151 Available Color Modes You can set the projector to use these color modes, depending on the input source you are using: Color mode Description Dynamic This is the brightest mode. Best for prioritizing brightness. Presentation Best for projecting vivid images. Cinema Best for enjoying content such as movies. sRGB Best for faithfully reproducing the color of the source image. DICOM SIM Best for projecting X-ray photographs and other medical images. This mode is for reference purposes only and should not be used to make medical diagnoses. Multi-Projection Best for projecting from multiple projectors (reduces the color tone difference between images). Turning On Automatic Luminance Adjustment You can turn on Dynamic Contrast to automatically optimize the image luminance. This improves the image contrast based on the brightness of the content you project. This setting is available for Dynamic or Cinema color modes.

Color Mode 64 a Turn on the projector and switch to the image source you want to use. b Press the [Menu] button on the control panel or remote control. c Select the Image menu and press [Enter]. d Select Dynamic Contrast and press [Enter]. e Choose one of the following options and press [Enter]: • Normal for standard brightness adjustment. • High Speed to adjust brightness as soon as the scene changes. f Press [Menu] or [Esc] to exit the menus. Adjusting the Image Color 65

You can fine-tune various aspects of how colors are displayed in your projected images. g Related Links • "Adjusting the Hue, Saturation, and Brightness" p.65 • "Adjusting the Gamma" p.65 Adjusting the Hue, Saturation, and Brightness You can adjust the Hue, Saturation, and Brightness settings for individual image colors. a Turn on the projector and switch to the image source you want to use. b Press the [Menu] button on the control panel or remote control. c Select the Image menu and press [Enter]. d Select Advanced and press [Enter]. e Select RGBCMY and press [Enter]. f Select the color to adjust, and press [Enter]. g Do the following as necessary for each setting: • To adjust the overall hue of the color, bluish - greenish - reddish, adjust the Hue setting. • To adjust the overall vividness of the color, adjust the Saturation setting. • To adjust the overall color brightness of the color, adjust the Brightness setting. h Press [Menu] or [Esc] to exit the menus. Adjusting the Gamma You can correct differences in projected image colors that occur between different image sources by adjusting the Gamma setting. a Turn on the projector and switch to the image source you want to use.

Adjusting the Image Color 66

b Press the [Menu] button on the control panel or remote control. c Select the Image menu and press [Enter]. d Select Advanced and press [Enter]. e Select Gamma and press [Enter]. f Select and adjust the correction value. When you select a smaller value, you can reduce the overall brightness of the image to make the image sharper. When you select a larger value, the dark areas of images become brighter, but the color saturation for lighter areas may become weaker. a • If you selected DICOM SIM as the Color Mode setting in the projector's Image menu, select the adjustment value according to the projection size. • If the projection size is 80 inches or less, select a small value. • If the projection size is 80 inches or more, select a large value. • Medical images may not be reproduced correctly depending on your settings and screen specifications. g If you want to make finer adjustments, select Customized and press [Enter].

Adjusting the Image Color 67 h Press the left or right arrow buttons to select the color tone you want to adjust on the gamma adjustment graph. Then press the up or down arrow button to adjust the value and press [Enter]. i Press [Menu] or [Esc] to exit the menus. g Related Links • "Image Quality Settings - Image Menu" p.151 Adjusting the Brightness 68

You can adjust the brightness of your projector's light source. a Turn on the projector and switch to the image source you want to use. b Press the [Menu] button on the control panel or remote control. c Select the Settings menu and press [Enter]. d Select Brightness Settings and press [Enter]. e Select Light Source Mode and press [Enter]. f Select one of the following options: • Normal lets you set the brightness to the maximum level. This makes the estimated life span of the light source approximately 20,000 hours. • Quiet lets you set the brightness to 70% and reduces fan noise. This makes the estimated life span of the light source approximately 20,000 hours. • Extended lets you set the brightness to 70% and extends the life expectancy of the light source. This makes the estimated life span of the light source approximately 30,000 hours. • Custom lets you to select a custom brightness level between 70 to 100%. g If you selected Custom, select Brightness Level from the Brightness Settings screen and use the left and right arrow buttons to select the brightness. h To maintain consistent brightness, turn on the Constant Brightness setting. a If you turn on Constant Brightness, you cannot change the Light Source Mode and Brightness Level settings. If you turn off Constant Brightness, the Brightness Level setting changes according to the status of the light source.

Adjusting the Brightness 69

i Press [Menu] or [Esc] to exit the menus. a Schedule periodic Light Source Calibration events in the projector's Extended menu in the following situations: • If you use the projector continuously for more than 24 hours in the Constant Brightness mode • If you regularly turn off the projector by shutting off the power outlet Otherwise, the Constant Brightness setting may not work properly. s Extended > Schedule Settings g Related Links • "Light Source Life Span" p.69 Light Source Life Span The estimated life span of the light source varies depending on the Brightness Level setting and whether Constant Brightness is on or off. a • The light source life span varies depending on the environmental conditions and usage. • The hours listed here are an approximate and are not guaranteed. • After 20,000 hours of use, you may need to replace parts in the projector. • If Constant Brightness is turned on, and you have exceeded the usage hours listed here, you may not be able to select a high Brightness Level setting. Constant Brightness off A Brightness level B Time before the brightness of the light source is reduced by half (approximate) Brightness Level setting Hours 100% 20000 hours 90% 21000 hours 80% 24000 hours 70% 30000 hours Constant Brightness on A Brightness level B Time the projector can maintain constant brightness (approximate) EB‑L615U/EB‑L610U/EB‑L610W/EB‑L610/EB‑L400U

Adjusting the Brightness 70 Brightness Level setting Hours 85% 6000 hours 80% 10000 hours 75% 14000 hours 70% 19000 hours EB‑L510U/EB‑L500W/EB‑L500 Brightness Level setting Hours 85% 17000 hours 80% 19000 hours 75% 22000 hours 70% 24000 hours Controlling the Volume with the Volume Buttons 71 The volume buttons control the projector's internal speaker system. You can also control the volume of any external speakers you connected to the projector. You must adjust the volume separately for each connected input source. a Turn on the projector and start a presentation. b To lower or raise the volume, press the [Volume] buttons on the remote control as shown. A volume gauge appears on the screen. c To set the volume to a specific level for an input source, select Volume in the projector's Settings menu. Caution Do not start a presentation at a high volume setting. Sudden loud noises may cause hearing loss. Always lower the volume before powering off, so that you can power on and then gradually increase the volume. g Related Links • "Projector Feature Settings - Settings Menu" p.155 Adjusting Projector Features Follow the instructions in these sections to use your projector's adjustment features. g Related Links • "Projecting Two Images Simultaneously" p.73 • "Projecting a PC Free Presentation" p.76 • "Projecting in Content Playback Mode" p.81 • "Shutting Off the Image and Sound Temporarily" p.85 • "Stopping Video Action Temporarily" p.86 • "Zooming Images" p.87 • "Using the Remote Control as a Pointer" p.88 • "Saving a User's Logo Image" p.89 • "Saving Settings to Memory and Using Saved Settings" p.91 • "Using Multiple Projectors" p.92 • "Projector Security Features" p.99 Projecting Two Images Simultaneously 73

You can use the split screen feature to simultaneously project two images from different image sources. You can control the split screen feature using the remote control or the projector menus. a • While using the split screen feature, other projector features may not be available and some settings may be automatically applied to both images. a Press the [Split] button on the remote control. The currently selected input source moves to the left of the screen. a You can perform the same operations from Split Screen in the projector's Settings menu. b Press the [Menu] button. You see this screen:

Projecting Two Images Simultaneously 74

c To select an input source for the other image, select the Source setting, press [Enter], select the input source, select Execute, and press [Enter]. a • You can only select input sources that can be combined. • While using the split screen feature, the Source screen appears when you change the input source from the remote control. d To switch images, select Swap Screens and press [Enter]. The projected images on the left and right are swapped. e To enlarge one image while reducing the other image, select Screen Size, press [Enter], select a size, and press [Enter]. To exit the menu, press [Menu]. a Depending on the video input signals, the images may not appear at the same size even if you select Equal. f To select the audio, select Audio Source, press [Enter], select an audio option, and press [Enter]. To exit the menu, press [Menu]. a Select Auto to hear audio from the largest screen or the left screen. g To align the projected images, select Align, press [Enter], select the setting, and press [Enter] again. To exit the menu, press [Menu]. h To exit the split screen feature, press [Split] or [Esc]. g Related Links • "Unsupported Input Source Combinations for Split Screen Projection" p.74 • "Split Screen Projection Restrictions" p.75 Unsupported Input Source Combinations for Split Screen Projection These input source combinations cannot be projected on a split screen.

Projecting Two Images Simultaneously 75

• Computer1 and Computer2 • USB and LAN Split Screen Projection Restrictions Operating restrictions The following operations cannot be performed during split screen projection. • Setting the projector's menu • E-Zoom • Switching the aspect mode (the aspect mode is set to Normal) • Operations using the [User] button on the remote control • Dynamic Contrast Image restrictions • If you make adjustments such as Brightness, Contrast, Color Saturation, Tint, and Sharpness in the projector's Image menu, you can apply them only to the image on the left. Default adjustments are applied to the image on the right. Adjustments that affect the entire projected image such as Color Mode and Color Temp. are applied for both left and right images. • Even if you make adjustments for Noise Reduction and Deinterlacing in the projector's Image menu, Noise Reduction is set to 0 and Deinterlacing is set to Off for the image on the right. s Image > Image Enhancement > Noise Reduction s Image > Advanced > Deinterlacing • Even if you set Display Background to Logo in the projector's Extended menu, the blue screen appears when no image signal is being input. g Related Links • "Image Aspect Ratio" p.58 • "Color Mode" p.63 • "Projector Feature Settings - Settings Menu" p.155 • "Input Signal Settings - Signal Menu" p.153 • "Projector Setup Settings - Extended Menu" p.158 • "Zooming Images" p.87 • "Adjusting the Image Color" p.65

Projecting a PC Free Presentation 76

You can use your projector's PC Free feature whenever you connect a USB device that contains compatible presentation files. This lets you quickly and File contents File type (extension) Details

easily display a presentation and control it using the projector's remote control. g Related Links • "Supported PC Free File Types" p.76 • "Precautions on PC Free Projection" p.76 Image .jpg Make sure the file is not: • CMYK format • Progressive format • Highly compressed • Above 8192 × 8192 resolution .bmp Make sure the file is not: • Above 1280 × 800 resolution .gif Make sure the file is not: • Above 1280 × 800 resolution • Animated • Interlaced .png Make sure the file is not: • Above 1280 × 800 resolution * • Interlaced

• "Starting a PC Free Slide Show" p.77 • "Starting a PC Free Movie Presentation" p.78 • "PC Free Display Options" p.79 Supported PC Free File Types Movie .avi (Motion JPEG) Supports only AVI 1.0. Make sure the file is not: • Saved with an audio codec other than PCM or ADPCM • Above 1280 × 720 resolution • Larger than 2 GB

You can project these types of files using the projector's PC Free feature. a • For best results, place your files on media that is formatted in FAT16/32. • If you have trouble projecting from media formatted for non Windows file systems, try formatting the media for Windows instead. * When you use a projector with a resolution of WUXGA, you can project a file with a maximum resolution of 1920 × 1200. Precautions on PC Free Projection Note the following precautions when using PC Free features. • You cannot use a USB key for PC Free features. • Do not disconnect the USB storage device while it is being accessed; otherwise, PC Free may not operate correctly.

Projecting a PC Free Presentation 77

• You may not be able to use the security features on certain USB storage devices with PC Free features. • When connecting a USB device that includes an AC adapter, connect the AC adapter to an electrical outlet when you use the device with your projector. • Some commercially available USB card readers may not be compatible with the projector. • The projector can recognize up to 5 cards inserted into the connected card reader at one time. • You cannot correct keystone distortion while projecting in PC Free, so correct the image shape before you begin your presentation. • You can use the following functions while projecting in PC Free. • Freeze • A/V Mute • E-Zoom • Pointer g Related Links • "Stopping Video Action Temporarily" p.86 • "Shutting Off the Image and Sound Temporarily" p.85 • "Zooming Images" p.87 • "Using the Remote Control as a Pointer" p.88 Starting a PC Free Slide Show After connecting a USB device to the projector, you can switch to the USB input source and start your slide show. a • You can change the PC Free operation options or add special effects by highlighting Option at the bottom of the screen and pressing [Enter]. a Press the [USB] button on the remote control. The PC Free file list screen is displayed. a • If the Select Drive screen is displayed, press the arrow buttons to select the drive and press [Enter]. • To display images on the other USB drive, highlight Select Drive at the top of the file list screen and press [Enter]. b Do one of the following to locate your files: • If you need to display files inside a subfolder on your device, press the arrow buttons to highlight the folder and press [Enter]. • To move back up a folder level on your device, highlight Back to Top and press [Enter]. • To view additional files in a folder, highlight Next Page or Previous Page and press [Enter], or press the [Page] up or down buttons on the remote control. c Do one of the following: • To display an individual image, press the arrow buttons to highlight the image and press [Enter]. (Press the [Esc] button to return to the file list screen.)

Projecting a PC Free Presentation 78

• To display a slide show of all the images in a folder, press the arrow buttons to highlight the Slideshow option at the bottom of the screen and press [Enter]. a • You can change the image switching time by highlighting Option at the bottom of the screen and pressing [Enter]. • If any file names are longer than the display area or include unsupported symbols, the file names may be shortened or changed only on the screen display. d While projecting, use the following commands to control the display: • To rotate a displayed image, press the up or down arrow button. • To move to the next or previous image, press the left or right arrow button. e To stop the display, follow the on-screen instructions or press the [Esc] button. You return to the file list screen. f Turn off the USB device, if necessary, and then disconnect the device from the projector. g Related Links • "PC Free Display Options" p.79 • "Connecting to a USB Device" p.26 Starting a PC Free Movie Presentation After connecting a USB device to the projector, you can switch to the USB input source and start your movie. a • You can change the PC Free operation options by highlighting Option at the bottom of the screen and pressing [Enter]. a Press the [USB] button on the remote control. The PC Free file list screen is displayed.

Projecting a PC Free Presentation 79

a • If the Select Drive screen is displayed, press the arrow buttons to select the drive and press [Enter]. • To display movie files on the other USB drive, highlight Select Drive at the top of the file list screen and press [Enter]. b Do one of the following to locate your files: • If you need to display files inside a subfolder on your device, press the arrow buttons to highlight the folder and press [Enter]. • To move back up a folder level on your device, highlight Back to Top and press [Enter]. • To view additional files in a folder, highlight Next Page or Previous Page and press [Enter], or press the [Page] up or down buttons on the remote control. c To play back a movie, press the arrow buttons to highlight the file and press [Enter]. a • If any file names are longer than the display area or include unsupported symbols, the file names may be shortened or changed only on the screen display. • If you want to play back all the movies in a folder in sequence, select the Slideshow option at the bottom of the screen. d To stop movie playback, press the [Esc] button, highlight Exit, and press [Enter]. You return to the file list screen. e Turn off the USB device, if necessary, and then disconnect the device PC Free Display Options You can select these display options when using PC Free. To access this screen, highlight Option at the bottom of the PC Free file list screen and press [Enter]. Setting Options Description Display Order Name Order Displays files in name order Date Order Displays files in date order Sort Order In Ascending Sorts files in first-to-last order In Descending Sorts files in last-to-first order Continuous Play On Displays a slide show continuously Off Displays a slide show once

from the projector. g Related Links • "PC Free Display Options" p.79 • "Connecting to a USB Device" p.26 Screen Switching Time No Does not display the next file automatically 1 Second to 60 Seconds Displays files for the selected time and switches to the next file automatically; high resolution images may switch at a slightly slower rate

Projecting a PC Free Presentation 80 Setting Options Description Effect No No effect Wipe Transitions between images using a wipe effect Dissolve Transitions between images using a dissolve effect Random Transitions between images using a random variety of effects


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply