Click here to download ELO IDS 6553L (01) PDF MANUAL

PDF Content Summary:

****** Page 1 ****** elo User Manual – IDS ET6553L USER MANUAL Elo TOUCh Solutions DS 65531 Monitor UM600326 Rev A, page I of 37

****** Page 2 ****** Copyright 0 2019 Elo Touch Solutions, Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc. Disclaimer The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its Affiliates (collectively “Elo”) makes no representations or warranties with respect to the contents herein, and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose. Elo reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of Elo to notify any person of such revisions or changes. Trademark Acknowledgments Elo, Elo (logo), Elo Touch, Elo Touch Solutions, and EloView are trademarks of Elo and its Affiliates. User Manual – IDS ET6553L UM600326 Rev A, page 2 of 37

****** Page 3 ****** Table of Contents Section 1: Introduction Section 2: Unpacking Section 3: IDS Touchmonitor Installation Section 4: Mounting Information Section 5: Operation Rev A page f 37 Section 6: Maintenance Information . Section 7: Technical Support Section 8: Regulatory Information 11 14 25 26 Section 9: Warranty Information………………………………………………………………………………………………………………………………………………………………………………………34 Section 10: Appendix A 35 User Manual – IDS ET6553L UM600326 3

****** Page 4 ****** Section 1: Introduction Product Description Your new Interactive Digital Signage (IDS) touchmonitor combines Elo Touch Solutions reliable performance with the latest developments in touchscreen technology and display design. This combination of features creates a natural flow of information between a user and the touchmonitor. This touchmonitor incorporates a 10-bit color, active matrix thin-film-transistor, and digital signage LCD panel to provide superior display performance. It outputs 4K resolution (3840 x2160) suitable for displaying graphics and images. Other features that enhance this LCD monitor’s performance are Plug & Play compatibility, built-in speakers and headphone output capability, Touch On Screen Display (OSD) controls, and a family of IDS computer modules. Elo Computer modules can be installed to the back of the monitor to convert the digital signage touchmonitor into an IDS All-in-One touchcomputer. Precautions Follow all warnings, precautions and maintenance as recommended in this user manual to maximize the life of your unit and prevent risks to user safety. For your health and safety, it is strongly recommended that at least two people handle, lift, and/or move these touchmonitors. This manual contains information that is important for the proper setup and maintenance of the IDS monitor. Before setting up and powering on your new touchmonitor, read through this manual, especially the Installation, Mounting, and Operation chapters. CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the Instructions. User Manual – ET6553L UM600326 Rev A, page 4 of 37

****** Page 5 ****** Section 2: Unpacking Unpacking the Interactive Digital Signage Touchmonitor To unpack the IDS, follow these steps: 1. The carton should be oriented in the manner according to its labeling. The hinged plastic locks should be at the ‘bottom’. 2. Open and remove all 4 hinged plastic locks. User Manual – ET6553L UM600326 Rev A, page 5 of 37

****** Page 6 ****** 3. Once the locks are removed, lift the cartons top lid off the bottom frame. 4. With the top lid removed, you now have access to the IDS touchmonitor and the included accessories. User Manual – ET6553L UM600326 Rev A, page 6 of 37

****** Page 7 ****** Verify that the box contains: 6553 Touchmonitor: • HDMI 2.0 cable USB 3.0 cable (Type A plug to Type B plug) power cable, IEC 60320-C13 to NA plug power cable, IEC 60320-C13 to EU/KR plug power cable, IEC 60320-C13 to I-JK plug Serial 3.5mm male to Serial DB9 female cable Energy label according to EU Regulation 1062/2010 2x Stylus Active or Passive depending on the monitors touch technology. o Active stylus for Projected Capacitance model o Passive Stylus for Infrared model Quick Install Guide On Screen Display (OSD) Remote (via RJ45 connector) User Manual – ET6553L UM600326 Rev A, page 7 of 37

****** Page 8 ****** 3 IOS 10 U iosxoxxoioo chion onnecor ? ane access JSB OS as-ot JM600326 p

****** Page 9 ****** IDS Touchmonitor: Connecting to an External Computer 1. 2. 3. 4. 5. Connect the included HDMI cable (or your own or DisplayPort cable) between the monitor and the video source. Connect the USB touch cable between the monitor and your host PC. Select the correct power cable for your region. Connect it between the AC power source and the touchmonitors POWER IN connector. As soon as power is detected, the monitor will turn on. In order to access the OSD menu, press the Menu button located behind the hidden door on the right side of the monitor. Power User Manual Video Select OSD Menu – ET6553L UM600326 Rev A, page 9 of 37

****** Page 10 ****** IDS Touchmonitor: Connecting to the Elo Computer Module (ECM) 1. 2. 3. 4. 5. Remove the cover in order to expose the computer module docking area. Slide the Elo Computer Module into the bay and secure the ECM with the locking screws. Select the correct power cable for your region. Connect it between the AC power source and the touchmonitors POWER IN connector. a. Note: The ECM can be plugged in while there is power the monitor. As soon as video is detected, the monitor will begin to display the content. In order to access the OSD menu, press the Menu button located behind the hidden door on the right side of the monitor. Visit the Elo Touch Solutions website for: Updates to the monitor firmware Detailed driver installation guides Touch drivers for other operating systems TouchPro and Infrared units are HID compatible and do not require an Elo touch driver. If an Elo touch driver has previously been installed on the host computer, remove this driver by opening Control Panel and selecting the option to remove the driver completely. User Manual – ET6553L UM600326 Rev A page 10 of 37

****** Page 11 ****** Section 4: Mounting Information Note: It is strongly recommended that at least two people handle, lift, or move these touchmonitors. Note: Do not leave the monitor facing down for long periods of time as this will cause permanent damage to the panel. Mounting Orientations The following mounting orientations are supported: landscape and portrait. Landscape When mounting the monitor in landscape mode, ensure that the Elo logo appears in the same location as the pictures below. User Manual – ET6553L UM600326 Rev A page I I of 37

****** Page 12 ****** Portrait Mode When rotating the monitor to portrait mode, ensure that the Elo logo appears in the same location as the pictures below. The 10 ports will be located at the bottom of the monitor. Rear VESA Mount A four-hole, 600x600mm and 400x400mm mounting pattern is provided on the rear of the monitor. The VESA FDMl-compliant mounting are coded VESA MOUNT PER MIS-F, 400 x M6 VESA MOUNT PER MIS-F, 600 x 600mm, M8 Refer to for dimensional drawings. User Manual – ET6553L UM600326 Rev A page 12 of 37

****** Page 13 ****** Optional Mounting Methods Elo Wall mount kit: PN E282876 An optional Wall Mount kit is available for the IDS6553L monitors. Detailed information is available on the marketing specification drawing MS602094 at Consult the wall mount user guide for detailed installation information. User Manual – ET6553L UM600326 Rev A page 13 of 37

****** Page 14 ****** Section 5: Operation Power To turn the touchmonitor on or off, press the touchmonitor power button once. If a computer module is installed, then the computer module will also turn on with the monitor. To gracefully shut down the computer module, follow the computer modules operating systems normal power off procedure. The system consumes low power when in SLEEP and OFF modes. For detailed power consumption specifications, refer to technical specifications available on the Elo website Touching the screen will bring the system out of MONITOR SLEEP mode. If long periods of disuse are planned, unplug the AC power cable to save power. The maximum voltage, frequency and current for the touchmonitor are provided in the power ratings table below: Operating Voltage Range 100 – 240Vac Usage Duty Cycle Operating Frequency Range 50/60 Hz In order to save energy and extend life of the display, Elo recommends shutting off the display when not in use. A number of tools, such as Content Management System (CMS) player applications, Operating System settings and the Real Time Clock feature on the On-Screen Display Menu (OSD) within the IDS display can be used for this task. Touch Technology When connected to Windows 10 computer, the touchmonitor will report simultaneous touches per the product specification. The monitors product specification can be found by visiting User Manual – ET6553L UM600326 Rev A page 14 of 37

****** Page 15 ****** Video Information An LCD panels native resolution is its width and height measured in number of pixels. In almost all cases, an image displayed on an LCD monitor will look best when your computers output resolution matches the LCD panels native resolution. See the display specifications on the Elo website to find your touchmonitors native resolution. Operating in other resolutions will degrade video performance and is not recommended. For computer output resolutions at non-native resolutions, the monitor will scale the video to panel’s native resolution. For smaller input video resolutions, this involves “stretching” the input image in the X- and Y-dimensions to fit the panel. For larger input video resolutions, this involves “compressing” the input image in the X- and Y-dimensions to fit the panel. An unavoidable byproduct of the scaling algorithms is a loss of fidelity when the computers output video image is scaled by the monitor to fit the display. This loss of fidelity is most apparent when viewing feature-rich images at close distances (for example images containing small-font text). Your touchmonitor will likely not require any video adjustments. Touch On-Screen Display (OSD) This monitor uses an easy-to-navigate Touch OSD interface. Use the settings menu in the sidebar to make adjustments to the monitor display settings Example of the Popup OSD Menu: Aspect Ratio Black Level Offset Brightness Contrast Sharpness Fill Screen O Standard 40% 40% Fill Aspect Direct O User Manual Select the desired OSD Setting Menu from here – ET6553L Video O Color Audio Information Power Time On Screen Display Conference 1 O 5% O Video Source Scan Video Port Discovery Brightness Sensor Active Video Resolution: 3840×2160, 60Hz Change Brightness by sliding this green bar. UM600326 Rev A page 15 of 37

****** Page 16 ****** All touchmonitor adjustments made through the OSD are automatically stored as soon as they are entered. This feature saves you from having to reset your choices every time the touchmonitor is unplugged or powered off and on or if there is a power failure. User Manual – ET6553L UM600326 Rev A page 16 of 37

****** Page 17 ****** Parameter Let’s Get Started Video Port Discovery Brightness Brightness Sensor Contrast Black Level Sharpness Aspect Ratio Color Temperature Color Sensor User Preset User Manual On Boot Up Video Color – ET6553L Available Adjustment On first boot up, the Language, Time and Time Zone must be selected When enabled, the monitor will automatically switch if a new video port is connected. Default: Enabled Adjust the brightness of the display. Default: 100 The light sensor can be toggled on or off. When the light sensor is enabled, the brightness cannot be changed manually. Table for light sensor is in Section 10: Appendix A Adjust the contrast of the display. Default: 50 The user can choose between Standard, 5%, 10% or 15% black level offset. The saturation level of the colors change according to the chosen black level offset. Adjusts sharpness of the displayed images. Default: no sharpness adjustment Sharpness function is disabled when the input source ratio is the same as the panels native ratio Adjusts aspect ratio of the display. Default: Fill Screen Fill Screen scales the X- and Y-dimensions of the input video (up or down as needed) to the display’s native resolution. Fill Aspect Ratio — Assuming a landscape orientation and an input video with aspect ratio smaller than 16:9, scales the Y-dimension of the input video (up or down as needed) to the display’s Y-resolution, and scales the X-dimension to maintain the aspect ratio (and fills the rest of the display with equal black bars on the left and right). Direct Output — 1: 1, Depends on whether the scalar can support it Adjusts color temperature. Color temperature options shall be 9300K, 7500K, 6500K, 5500K, and User Defined. Default: User Defined Adjust the color based on ambient colors If the User Preset option is selected, the user can change the color temperature by changing individual R, G, and B gains on a scale from 0 to 100. UM600326 Rev A page 17 of 37

****** Page 18 ****** Picture Modes HDMI Full Color Range Audio Selections Power Loss Behavior Power Lock Energy Savings Mode Power Status Light Time Set On/Off Schedule User Manual Audio Power Time – ET6553L If the color space is YUV mode, then Hue and Saturation can be varied in this menu. Preset color modes that change the color parameters to enhance color definitions. Available modes are: Standard, Movie, Gaming, Photo, Line mode, Color Enhance Default: Standard When enabled, displays full color range of HDMI (0-255) When disabled, displays the legacy color range (16-255) Default: enabled Audio Output: Sets where audio should play from When set to internal-PC, the audio comes out from the line out on the ECMG4 When set to Monitor, the audio comes out from the line out on the monitor Mute: enables or disables the audio Default Off Volume: Adjust the audio from 0 100 Default: 50 When power to the monitor is lost and regained, the behavior that is chosen will be executed. Always On Always Off Last State Default: Last State When enabled, the monitor will remain ON even if the power button is pressed. If this feature is enabled and power to the monitor is lost, when power is regained, pressing the power button will turn on the monitor. Default: Disabled When Enabled, the monitor must adhere to Energy Star regulations. Default: Enabled Enable or disable the power status light Default: Enabled Option to set the current time Set the monitor to turn off and on at specific times. Default: Everyday Off: 01 On: UM600326 Rev A page 18 of 37

****** Page 19 ****** Recall Defaults OSD Timer On Screen Display OSD Language User Manual Information Conference – ET6553L OSD Lock OSD Portrait Rotation Monitor Information System Temperature Help & Support Screen Share Power Behavior Selecting “Recall Defaults” restores all factory default settings for OSD-adjustable parameters (except OSD Language and OSD Time Settings) and for Preset Video Mode timings. Adjusts how long a period of OSD button inactivity the touchmonitor will wait before closing the OSD. The adjustable range is between 5 and 60 seconds. Default: 15 seconds Selects which language the OSD information is displayed in. The available languages are: English, French, Italian, German, Spanish and Russian. Default: English. When selected, the OSD will not popup when the Menu button is pressed. If the OSD needs to be unlocked, press and hold the Menu button for five (5) seconds. This will cause the monitor to unlock the OSD menu. Adjusts the OSD orientation between Portrait and Landscape mode Displays the touchmonitor model and the monitor and touchscreen serial # information Displays the real-time temperature of the Video Board Note: CPU Sensor temperature is only available if the feature is supported by the computer module. Display information regarding Elo Touch Solutions contact information. When an active video signal is connected to the conference HUB (via HDMI or USB type C), the video signal will be automatically displayed within the ECMG4’s operating system at full screen Default: Enabled When enabled, the conference hub will remain ON even if the monitor is in sleep mode. Default: Disabled UM600326 Rev A page 19 of 37

****** Page 20 ****** On-Screen Display (OSD) – Connected Through the RJ45 Connection Five OSD buttons can be found on the OSD remote. There is an LED light which shows the current state of the monitor. The following are the functions that relate to the designated button. Note: Opening the OSD menu from the remote will disable the touch functions on the OSD menu. MENU The buttons and their functionality are: Button Menu User Manual – ET6553L Function when OSD is not displayed: Display OSD main menu n/a Power for the monitor n/a Function when OSD is displayed: Return to previous OSD menu Increase value of selected parameter / select next menu item Toggles the power status of the monitor Decrease value of selected parameter / select revious menu item UM600326 Rev A page 20 of 37

****** Page 21 ****** Audio Audio can be output from the following locations: 1. From the monitor speakers via the video channel 2. The Line Out port on the monitor 10 ports 3. If an Elo Computer Module is installed, then then from the computers Line Out port See the “Audio” OSD parameter for details. Note: When headphones are plugged into the headphone output jack, the internal speakers turn off and audio is played over the headphones. Volume and muting of the speaker and headphone outputs are controlled by the OSD. Controlling the monitor remotely The touchmonitor has the ability to allow remote access from a host application. This is done through the use of either the VESA Display Data Channel Command Interface (DDC/CI) or the Multiple Display Control command sets. Users can communicate with the monitor through either of these protocols. The host application can send a variety of different commands which will be executed on the touchmonitor. For detailed information regarding the command set, refer to the application note available here. CEC Functionality (Consumer Electronic Control) The touchmonitor is equipped with CEC capability. If a host device (with CEC built in) is connected to the monitor through HDMI, the monitor can be turned on by only turning the host device on. Real Time Clock (RTC) Functionality This touchmonitor has real time clock functionality which will help to prolong the lifetime of the touchmonitor. In the OSD menu, there is a sub-menu called RTC Settings. To utilize the RTC functionality: The user must set up the Time setting for their specific time zone. User Manual – ET6553L UM600326 Rev A page 21 of 37

****** Page 22 ****** When the On/Off Schedule is Enabled, the user can choose when to leave the monitor on and when it should be off. Individual or multiple days can be chosen. Example: Have the monitor ON for Monday, Wednesday and Friday between 9:00AM and 5:00PM. All other days and time, the monitor shall be OFF. O o o Enable the On/Off Schedule Select M W F Set the ON time for and the OFF time for *Note that all of time settings operate on the 24-hour clock. Wake-On-Touch The touch display supports wake-on-touch functionality when the PC is in sleep mode. To enable this, please ensure that the BIOS settings have enabled USB support during the S4 sleep cycle. Intelligent Brightness Control and Color Sensor Functionality This touchmonitor includes a light and color sensor that can adjust the brightness of the screen and the color of the display to meet the ambient light and color levels. Details of the functionality can be found in the Section 10, Appendix A. User Manual – ET6553L UM600326 Rev A page 22 of 37

****** Page 23 ****** Energy Saving Mode This monitor can meet Energy Star 7.0 requirements, if Energy Saving Mode is enabled. When Energy Saving Mode is enabled, maximum brightness will be limited to 65%. To restore full functionality of the touchmonitor, disable the Energy Saving Mode. Stylus (Active and Passive) Elo provides active stylus pens that can be used on the projected capacitance version of the monitor. Elo Active Stylus Part Number: E216215 Please visit for Stylus API’s. Elo also provides passive stylus pens that be used on the Infrared version of the monitor which can be used simultaneously with finger for touch. Elo Active stylus Part Number: E727568 Edge Connect microUSB Peripheral Ports Available on all four sides of the monitor are microUSB ports designed for Elo’s optional peripheral ports. See for the optional peripherals that work with the ET6553L display. The pinout is as follows: Pini: 5V Power Pin2: USB D- Pin3: USB D+ Pin4: USB OTG Pin5: Ground If the trigger function is required (such as a bar code reader peripheral), contact Elo Touch Solutions for the available APIs. User Manual – ET6553L UM600326 Rev A page 23 of 37

****** Page 24 ****** Camera (Optional) Elo provides an optional camera module which has a built-in microphone and proximity detection sensor. This camera is designed for video conferencing meetings and supports 1080P Full HD video output. User Manual – ET6553L UM600326 Rev A page 24 of 37

****** Page 25 ****** Section 6: Maintenance Information To avoid risk of electric shock, follow all safety notices and do not disassemble the touchmonitor or Computer Module. They are not user- serviceable. Do not block or insert anything inside any of the ventilation slots. The touchmonitor is equipped with a 3-wire, grounding power cord. The power cord plug only fits into a grounded outlet. Do not fit or modify the plug into an outlet that has not been configured for this purpose. Do not use a damaged power cord. Only use the power cord that came with your Elo Touchmonitor. Use of an unauthorized power cord may invalidate your warranty. Ensure that the system is maintained and runs within the specified environmental conditions listed in the products specifications available on the Elo Touch Solutions website User Manual – ET6553L UM600326 Rev A page 25 of 37

****** Page 26 ****** Section 7: Technical Support Technical Assistance Technical Specifications visit for technical specifications for this device Refer to last page for worldwide technical support phone numbers. User Manual – ET6553L Support visit for technical support UM600326 Rev A page 26 of 37

****** Page 27 ****** Section 8: Regulatory Information Waste Electrical & Electronic Equipment Directive (WEEE) This product should not be disposed of with household waste. It should be deposited at a facility that enables recovery and recycling. Elo has put in place recycling arrangements in certain parts of the world. For information on how you can access these arrangements, please visit Electrical Safety Information Compliance is required with respect to the voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified herein will likely result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. There are no operator serviceable parts inside this equipment. There are hazardous voltages generated by this equipment which constitute a safety hazard. Service should be provided only by a qualified service technician. Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment to mains power. Emissions and Immunity Information Notice to Users in the United States. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with Part 15C of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference; and 2) This device must accept any interference, including interference that may cause undesired operation of the device. User Manual – ET6553L UM600326 Rev A page 27 of 37

****** Page 28 ****** Notice to Users in Canada: This equipment complies with the Class A limits for radio noise emissions from digital apparatus as established by the Radio Interference Regulations of Industrial Canada. CAN This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’lndustrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage;et (2) liutilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, méme si le brouillage est susceptible djen compromettre le fonctionnement. Notice to Users in the European Union: Use only the provided power cords and interconnecting cabling provided with the equipment. Substitution of provided cords and cabling may compromise electrical safety or CE Mark Certification for emissions or immunity as required by the following standards: This Information Technology Equipment (IT E) is required to have a CE Mark on the Manufacturer’s label which means that the equipment has been tested to the following Directives and Standards: This equipment has been tested to the requirements for the CE Mark as required by EMC Directive 2014/30/ EU as indicated in European Standard EN 55032 Class A and the Low Voltage Directive 2014/35/EU as indicated in European Standard EN 60950-1. General Information to all Users: This equipment generates, uses and can radiate radio frequency energy. If not installed and used according to this manual, the equipment may cause interference with radio and television communications. There is, however, no guarantee that interference will not occur in any particular installation due to site-specific factors. User Manual – ET6553L UM600326 Rev A page 28 of 37

****** Page 29 ****** 1. In order to meet emission and immunity requirements, the user must observe the following: a. Use only the provided 1/0 cables to connect this digital device with any computer. b. To ensure compliance, use only the provided manufacturer’s approved line cord. c. The user is cautioned that changes or modifications to the equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 2. If this equipment appears to cause interference with radio or television reception, or any other device: a. Verify as an emission source by turning the equipment off and on. If you determine that the equipment is causing the interference, try to correct the interference by using one or more of the following measures: i. Move the digital device away from the affected receiver. ii.Reposition (turn) the digital device with respect to the affected receiver. iii. Reorient the affected receiver’s antenna iv. Plug the digital device into a different AC outlet so the digital device and the receiver are on different branch circuits. v. Disconnect and remove any 1/0 cables that the digital device does not use. (Unterminated 1/0 cables are a potential source of high RF emission levels.) vi. Plug the digital device into only a grounded outlet receptacle. Do not use AC adapter plugs. (Removing or cutting the line cord ground may increase RF emission levels and may also present a lethal shock hazard to the user.) If you need additional help, consult your dealer, manufacturer, or an experienced radio or television technician. User Manual – ET6553L UM600326 Rev A page 29 of 37

****** Page 30 ****** Agency Certifications The following certifications and marks have been issued or declared for the IDS 6553L monitor: UL, FCC (US) – Class A CUL, IC (Canada) CB (International safety) CE (Europe) – Class A RCM (Australia) VCCI (Japan) CCC (China) (for TouchPro version only) User Manual – ET6553L UM600326 Rev A page 30 of 37

****** Page 31 ****** China RoHS In accordance to Chinese law (Management Methods for the Restriction of the Use of Hazardous Substances in Electrical and Electronic Products), the section below lists out the name and amount of the toxic and/or hazardous materials that this product may contain. Hazardous Substances Component Name Plastic Parts Wire and Cable Assembly PCBA Lead (Pb) o o x Mercury (Hg) O O O Cadmium(Cd) o o o Hexavalent Chromium (Cr6+) o O o Polybrominated Biphenyls (PBB) o O o Polybrominated Diphenyl Ethers (POE) o O o This table is prepared in accordance with the provisions of SJ/T 1 1364 O: Indicates that said hazardous substance contained in all homogenous materials for this part is below the limit requirement of GB/T 26572. X: Indicates that said hazardous substance contained in at least one of the homogenous materials used for this part is above the limit requirement of GB/T 26572. For items marked with X, exemptions were taken according to EU RoHS. User Manual – ET6553L UM600326 Rev A page 31 of 37

****** Page 32 ****** Explanation of Markings In accordance with the SJ/TI 1364 requirement, electrical and electronic products are marked with the following pollution control logo. The Environment-Friendly Use Period for this product is 10 years. The product will not leak or mutate under normal operating conditions listed below, so that the use of this electronic information product will not result in any severe environmental pollution, any bodily injury, or damage to any assets. Operating Temperature: See chart below Storage Temperature: See chart below It is encouraged and recommended that product packaging be recycled and reused according to local laws. User Manual – ET6553L UM600326 Rev. A, page 32 of 37

****** Page 33 ****** Power Specifications Electrical Ratings Input 1 00 – 240 VAC 50/60Hz Operating & Storage Conditions Operating Conditions Temperature Humidity Storage Conditions Temperature Humidity User Manual – ET6553L ooc – 400C 20% to 80% (non-condensing) -200C – 500C to 95% (non-condensing) UM600326 Rev. A, page 33 of 37

****** Page 34 ****** Section 9: Warranty Information For warranty information, go to User Manual ET6553L UM600326 Rev. A, page 34 of 37

****** Page 35 ****** Section 10: Appendix A Light Sensor Curve Brightness Curve c User Manual 300 250 200 150 100 50 10 ET6553L 15 20 25 30 35 40 45 50 55 60 Light Sensor Value 65 70 75 80 85 90 95 100 100 UM600326 Rev. A, page 35 of 37

****** Page 36 ****** Color Sensor The color sensor functions according to the following chart: Tungsten Candle Halogen Noon Sunlight Household Shade Infrared Embers 800’K 1800*K Incandescent 2800*K 3200’K 5500K Fluorescent Monitors 65WK 80000K User Manual ET6553L Skylight Ultraviolet 12-20.000*K UM600326 Rev. A, page 36 of 37

****** Page 37 ****** Visit our website for the latest Product Information Specifications Upcoming Events Press Releases Software Drivers Touchmonitor Newsletter To find out more about our extensive range of Elo touch solutions, go to, or call the office GIO nearest you. North America Tel +1 408 597 8000 Fax +1 408 597 8001 Europe Tel +32 6 70 45 OO Fax +32 70 45 49 Asia-Pacific Tel +86 (21) 3329 1385 Fax +86 (21) 3329 1400 User Manual ET6553L Latin America Tel 786-923-0251 Fax UM600326 Rev. A, page 37 of 37








Leave a comment, question, review or page error below. Account not required.

This site uses Akismet to reduce spam. Learn how your comment data is processed.