Click here to download ELITE SCREENS F84NWH (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** Portable Floor Pull-Up Screen Elite ez Cinema Series FOR MODELS: F60NWV / F72NWV / F84NWV / FIOONWV F84NWH FIOONWH USER’S GUIDE MATTE WHITE Rev. 1.0

****** Page 2 ****** PARTS IDENTIFICATION: Front Bleck edge ffhite screen(for project-ion Upper scroll Hanging hook Black screen materiel Pull hook Brecket hook Small aupport rod Locking a]eeve Lock Base foot Box Big support rod Cover of the box Back Rev. 1.0

****** Page 3 ****** Precautions: Warning! Screen damage can result from product mishandling if the enclosed precautions are not followed. In accordance with practicing home fire safety and to avoid screen damage, do not place the screen near or beside a fireplace or high temperature appliances such as a gas stove, BBQ or heater. (Fig. l) Fig.l Place the screen beyond the reach of children. (Fig.2) Operational Instructions: Installation: Fig.2 The EZ-Cinema screen is designed to be used as an easy to operate portable screen for a variety of presentation environments. Its design enables it to be versatile for use in either classroom, conference room, home or patio presentations. When packed, the unit carries with ease and opens up for projection presentations within seconds. As a general rule, portable projector screens should be installed in an area free from wind and heat or open flame sources such as a heater, BBQ grill or fireworks display. Extend the base feet: Locate the base feet on the bottom of the box cover at each end and rotate the base foot until it forms a right angle between the footboard and the cover box. Rev. 1.0

****** Page 4 ****** Open the box cover: Unlatch the buckles on both ends of the box and open the box cover. Next, secure the box with one hand while removing the support rod with your other hand. Installing the support rod: First, make sure that the hanging hook is pointing toward the front facing the same direction as the screen, then insert the square end of the support rod into the support plate as shown below. Support Plate Pull up the screen: Hold the pull hook with one hand, pull the screen up gently and hang it on the bracket hook. Vertical Adjustment: First loosen the locking sleeve, and then hold the small support rod with the left hand so as to slowly raise it upwards until the screen is fully stretched to the desired position. Rev. 1.0

****** Page 5 ****** Adjusting the screen: Hold the screen with the left hand when the screen has been stretched to the desired position, and then rotate the locking sleeve clockwise with the right hand until the rod is properly locked into position. Screen completely assembled Rev. 1.0

****** Page 6 ****** Preparing screen for storage l. Pulling down the screen: First, hold the telescoping support rod with the left hand and loosen the locking sleeve counter-clockwise with the right hand. Then shorten the telescoping support rod slowly into the full retracted position and tighten the locking sleeve to secure it in place. 2. Retract the screen: Remove the pull hook from the support bracket by lifting it about 2 cm up and then hold on to the pull hook and lower the screen gently into the box. 3. Pulling out the support rod: After telescoping the small supporting rod to its shortest position and tightening the locking sleeve, take out the supporting rod from the support plate. Rev. 1.0

****** Page 7 ****** 4. Storing the support rod: Properly center the supporting rod in the middle to maintain the weight balance in the box when carrying. 5. Draw the base feet back: Slightly lift each end of the box in turn rotating the two base feet underneath until they are back into alignment with the box. 6. Storing the screen: The recommended place for storage would be a corner of the room or in a closet, but the ultimate choice is up to you. Rev. 1.0

****** Page 8 ****** The following points should be noted to assure the sound performance of the screen l. Never use your hand to touch the screen surface. 2. Never scrabble on the screen with anything. 3. Don’t touch the screen with hard or sharp objects. 4. Please use a clean cotton cloth or soft dust brush to remove any dust particles on the screen. 5. The screen material may be cleaned arranty Policy Manual, Tripod, Pull-up Floor, and Fixed Frame Screens *Warranty policy applies to claims made in the United States of America. Warranty issues outside of the US must go through their international distributor. Two (2) year warranty parts and labor from purchase date as follows (except for refurbished units as specified below): Refurbished units carry a 90-day parts and labor warranty. Demo units or open box items are AS IS items and do not carry a warranty. Elite Screens will cover ground shipping charges on warranty claims made within 7 days of receiving per our DOA (Defective On Arrival) policy Each party will be responsible for one way shipping during the regular warranty period if the claim is made after the 7 day DOA period. An RIMA (Return Merchandise Authorization) number must be issued in order to process a replacement. Elite Screens will either replace or repair the defective unit with a brand new replacement *(see exceptions below) after the defective unit is received and/or confirmed defective. Once the product is received, Elite Screens will send out a new *unit to the customer by ground service (subject to inventory availability). Missing Parts must be reported within the 7-days of receipt. If reported after 7 days, customer will only be responsible for shipping and handling fees. If reported after 30 days of receipt, the customer is responsible for cost of the parts and shipping & handling fees. Please visit the link below for full warranty information elitescreens.com/services.html *A new or refurbished replacement will be sent out to the customer depending on the type of purchase (new or refurbished) and is based on stock availability. Rev. 1.0

****** Page 9 ****** Two WAY TO REGISTER YOUR WARRANTY WITH ELITE SCREENS INC. A. On Line (Faster and Easier) elitescreens.com/register.html B. Fill out & Fax to (562) 483-8498, Attn: Customer Service Dept. *Your Name: Address: City/State/Zip *Email Address: *Phone: *Screen Model: *Serial Number: *Date of Purchase: *Dealer / Reseller Purchased from (name of the reseller): What is your Projector Model : Application: Ilome Others Education Corporation Government 0k Improvement needed flow would you rate this screen? Excellent Good Comments: Contact info: If you have pictures of your screen you’d like to share with us, please email your pictures to eliteinfo@elitescreens . com or call us at 877-511-1211 elitescreens.com For any technical inquiries, techsupport@elitescreens.com Rev. 1.0

****** Page 10 ****** Portable Floor Pull-Up Screen Elite ez Cinema Plus Series FOR MODELS: F68xws1 / F60XWV1 F84XWV1 / F74XCH1 / F84XCH1 USER’S GUIDE rtro’:•• Matte White Rev 1.0

****** Page 11 ****** Precautions: Warning! Screen damage can result from operational errors if the enclosed precautions are not followed. In accordance with practicing home fire safety and avoiding screen damage, do not place the screen near or beside a fireplace or high temperature objects such as a gas stove, BBQ or heater. Place the screen beyond the reach of children. Fig. I Black Screen Material White Screen Box (casing) Base Feet ——–…………………………………………………………………+ Fig. 3 Fig. 2 Flex Bar* Top Support Bar Box Cover (Lid) *Note: The Flex Bar is a feature designed to evenly distribute the tension of the screen out to the sides. The Flex Bar is designed to “bow” out from the Top Support Bar. It may bow out a few inches depending on the size of the screen. (Fig.3) Rev 1.0

****** Page 12 ****** O erational Instructions: Installation The screen should be installed in an area free of very strong wind and away from any fire activity such as a heater, BBQ grill or fireworks display. 1. Extend base feet: Locate the base feet on the bottom of the box at each end and rotate them until they form right angles. 2. Open the box cover: Unlatch the buckles at both ends of the box and open the box cover. 3. Pulling up the screen: Carefully lift the screen by its handle and stop at the desired height position. The screen’s “scissor back” spring configuration will support it. Pull Note: The screen will only stop shortly after the bottom black rise has been exposed. Rev 1.0

****** Page 13 ****** Putting screen away 1. Retract the screen into case: Press the screen’s handle slowly in a downward motion and allow the screen to retract back gently into the housing. 2. Closing it up: Snap the buckles into place at both ends and verify that the screen’s box is closed securely. 3. Draw the base feet back: Slightly lift one end of the box at a time and rotate the two feet on the bottom of the box until they are in parallel alignment with the box. Rev 1.0

****** Page 14 ****** 4. Storing the screen: The recommended place for storage would be a corner spot or in a closet, but the ultimate choice is up to you. The following points should be noted to assure the sound performance of the screen. l. Never use your hand to touch the screen surface. 2. Never scrabble on the screen. 3. Don’t touch the screen with hard or sharp objects. 4. Please use clean cotton cloth or soft dust brush to remove dust particles from the screen. Warran Polic Manual, Tri od, Pull-u Floor, and Fixed Frame Screens Two (2) year warranty parts and labor from purchase date as follows (except for refurbished units as specified below): Refurbished units carry a 90-day parts and labor warranty. Demo units or open box items are AS IS items and do not carry a warranty. Each party will be responsible for one way shipping during the warranty period. DOA (Defective On Arrival): Must be reported within 7 business days of receipt. A RMA (Return Merchandise Authorization) number must be issued in order to process a replacement. Elite Screens will replace the DOA (Defective On Arrival) unit with a brand new replacement *(see exceptions below) after the DOA unit is received and/or confirmed defective. Once the product is received, Elite Screens will send out a new *unit to the customer by ground service (subject to inventory availability). Should a problem be reported after the 7-day grace period, the item must be shipped to us for warranty repair. Missing Parts must be reported within the 7-day (DOA) grace period. If reported after 7 days, customer will be only be responsible for shipping and handling fees. If reported after 30 days of receipt, customer is responsible for cost of the parts and shipping & handling fees. Rev 1.0

****** Page 15 ****** Two WAY TO REGISTER YOUR WARRANTY WITH ELITE SCREENS INC. A. On Line (Faster and Easier) elitescreens.com/register.html B. Fill out & Fax to (562) 483-8498, Attn: Customer Service Dept. *Your Name: Address: City/State/Zip *Email Address: *Phone: *Screen Model: *Serial Number: *Date of Purchase: *Dealer / Reseller Purchased from (name of the reseller): What is your Projector Model : Application: Home Others Education Corporation Government 0k Improvement needed flow would you rate this screen? Excellent Good Comments: Contact info: If you have pictures ofyour screen you’d like to share with us, please email your pictures to eliteinfo@elitescreens.com or call us at Elite$C#ääN$ elitescreens.com For any technical inquiries, techsupport@elitescreens.com Rev 1.0

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL



ELITE SCREENS F84NWH (01) PDF MANUAL

Leave a comment, question, review or page error below. Account not required.

This site uses Akismet to reduce spam. Learn how your comment data is processed.