Click here to download ELITE SCREENS EVANESCE (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** SCREENS In-Ceiling Front Projection Screen Evanesce Series User’s Guide Rev.012710-JA info@elitescreeens.com 1 info@elitescreens.com

****** Page 2 ****** Important Safety and Warning Precautions Be sure to read this user guide before use and follow the procedures below. Please retain this manual for future reference. To avoid any damage, do not use in conjunction with any accessories not recommended by the manufacturer. Handle the device carefully during transportation to avoid damage. To ensure safe and reliable operation, direct connection to a properly grounded power source is advised. The power outlet supplying power to the unit should be close to the unit and easily accessible. Do not install the device on uneven or inclined surfaces. Do not put heavy objects on the power cord and position it properly to avoid creating a trip obstacle. Never overload the power cord to prevent an electric shock or fire. Guard the device from any liquid or foreign objects to avoid electrical shock or fire due to loose contact or short circuit. There are no user serviceable parts in the device. Do not attempt to disassemble this device by yourself. No one except authorized technicians can open this device to make repairs. Make sure the power source this device is connected to has a continuous power flow. If there is a need to use an extension cord, make sure the cord has the same equal rating as the appliance to avoid overheat. Do not handle the power plug when your hands are wet or your feet are in contact with water. 2. Do not use this device under the following circumstances: Disconnect the power cord under the conditions of heavy rain, wind, thunder or lighting. Avoid direct sunshine, rain shower or moisture. Keep away from fire sources and high temperature to prevent this device from overheating. Cut off the power supply first before transportation or maintenance. Fully disconnect from the power supply when screen is not in use for a long period of time, as should be done with any other electric household appliance. To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is obvious damage or if there are any evident broken parts 2

****** Page 3 ****** Warning The screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra black top drop in the roller. Please be aware of this as it will void the limitation ofyour warranty. Changes or modifications (except cutting the power cord for hardwire installation) to this unit not expressly approved by Elite Screens is prohibited and will void the warranty. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Reorient or relocate the receiving antenna of the device which may be causing interference v’/ Increase the separation between the screen and the device’s receiver Connect the equipment into a different power outlet than the device’s Consult the dealer or an experienced Radio/TV technician for help Evanesce Standard Accessories A. IR Remote B. RF Remote C. 3-way switch F. Bubble level eye” receiver reen OV (-) Red 12V (+) E. 5-12 volt trigger adaptor cable Note: Contact your reseller for optional accessories or visit shop.elitescreens.com for accessories purchase. G. AAA Batteries 3

****** Page 4 ****** Control System 1. 5-12V Trigger: The built-in 5-12 V trigger input for your new CineTension2 allows your screen to synchronize its drop and rise with the projector’s power cycle. The screen drops when the projector powers up and retracts when the projector powers down. The 5-12 volt adaptor connects to your projectors trigger output via a separate cable that may or may not be provided by the projector manufacture. The trigger feature will not work without an output cable from the projector, but it can be tested using a 9-volt battery by simply connecting the Red (+) and Green (-) cable to the 9-volt battery. RJ-45 input for 5-12 v 5-12V RJ-45 cable To Projector Red DC12 Green OV 2. 3-way switch and IR (Infrared) Eye Receiver: The 3-way Wall Box switch enables the consumer to manually operate the screen’s drop/rise capabilities. The IR “eye” protrudes from the bottom ofthe casmg to present a low profile line-of-sight control option for your IR remote. It is a low-visibility alternative to using the 3-wall switch and its ability to protrude from the bottom of the screen allows line-of-sight control even in a recessed ceiling installation. pins ease Sena.0t 3. Infrared (IR) and Radio Frequency (RF) Remote Controls: Although the IR remote requires a direct line of sight with the IR sensor to function, the screen’s case can be hidden from sight and operated using the RF remote. When depressing the directional buttons you should hear a faint click signifying that the mechanism is working properly. This is the IR remote with a range of 25 Ft. Requires 2x AAA batteries. Stop IBII Thi is the RF remote with a range of 100 Ft. Requires 2x AAA batteries. ** Please remember to always point to the wall switch receiver when using the IR remote. The IR remote can also work with a Universal Learning Remote Control usually by programming the Screens IR codes into your Universal Learning Remote. 4

****** Page 5 ****** 4. In-wall RJ-45 Module: The RJ-45 module connects to a local wall switch for Up/Down control of your Evanesce electric projection screen. Please follow the picture diagram below for instructions on how to connect this accessory. Elite Screens In-Wall Switch Module ( ZIW-Module ) Ethernet (RJ45) network cable (not included) Yellowitemmanl Elite Electric/Motorized Screen Local wall switch In-wall switch module (ZIW-Module) Steps to attach Elite Screens Motorized Screen to vour local wall switch 1. 2. 3. Attach Elite Screens in-wall switch module (Part #: ZIW-Module) to your local wall switch as shown in diagram above Attach an RJ-45 Ethernet cable (not included) to the ZIW-Module and the other end to the RJ-45 input on your Elite electric screen After testing the connection, place the in-wall switch module in/on the wall and wire the Ethernet cable into the wall and complete the setup. Note: Please be aware that Ethernet cables have length limitations so please make a test first before concealing the cable into the wall. Installation l. Power: The Evanesce series screen includes a 3-prong power cord for using in a non-concealed power outlet. Ifyour installation however will be entirely concealed including the power outlet, we strongly recommend a hardwire connection. Please refer to the diagram below for wiring information for both I I Ov and 220v variants. 5 110 220V “3 ttlue

****** Page 6 ****** 2. Mounting Parts A E 4-6 pcs 8-10 pcs B F 4-6 pcs 4-6 pcs C 2-3 pcs D 4 pcs Please make sure all parts listed above are included. If any parts are missing please contact us right away. 3. Assembling the top bracket (C) I. Insert the hex screw (B) through the bracket’s screw hole II. Secure and screw the hex screw (B) with the hex nut (A) III. Slide the top bracket (C) through the railing on top of the case 4. Securing the Suspension Bar (D) I. Place the suspension bars (D) on the top bracket (C) and align with the hole as shown below. II. Insert hex screw (B) through the hole with a washer (E) and tighten it with the hex nut (B). III. Affix the suspension bars to your ceiling according to the distance of A and B.

****** Page 7 ****** 5. Optional installation (parts not included) Screw bolt X 4 Washer X 8 Nut x 8 I. Place the top brackets (C) in the desired location on the screen’s housing and measure the distance between them as depicted on L. II. Mark the location of where the screen will be installed according to the L distance and then secure the screw bolt to the ceiling. 112m III. Install the screen to the screw bolt as show in the figure below. 7

****** Page 8 ****** Eva neøee Serieø Table Sets-en 90 16 101 t 824′ 024 96 2226 u nga:h tlS t 18 118 118 46 3182 unci 92 4 64 2199 2144 am 8:29 itm 39 3b 92 0 1029 00 740 240 20 0 30 39 39 *Measurement dimensions are intended as a reference only and subject to change without notice. Note: Data Error may be II 3 4 tso 49 49 4b SO 49 49 49 01 II r—Al 83 8

****** Page 9 ****** Trouble Shooting Ifthe electric screen does not move, please check the following: 1. 2. 3. 4. Check the power supply first. The screen will understandably not move without power. Make sure the power cord is firmly plugged to the power outlet. Make sure that all cable connections are secure. Ifthe screen works well with the line switch but not with the remote control, please make sure the controls have fresh batteries or replace them with new ones. Change the battery every 6 remote Months to ensure proper operation of the remotes. 5. For all other problems, please contact us according to your country. Warranty Policy Two (2) year parts and labor warranty from purchase date as follows (except for refurbished units as specified below): Refurbished units carry a 90-day parts and labor warranty. Demo units or open box items are AS IS items and do not carry a warranty. Each party will be responsible for one way shipping during the warranty period. DOA (Defective On Arrival): Must be reported within 7 business days of receipt. An RMA (Return Merchandise Authorization) number must be issued in order to process a replacement. Elite Screens will replace the DOA (Defective On Arrival) unit with a brand new replacement *(see exceptions below) after the DOA unit is received and/or confirmed defective. Once the product is received, Elite Screens will send out a new* unit to the customer by ground service (based on stock availability). Should a problem be reported after the 7-day grace period, the item must be shipped to us for warranty repair. Missing Parts must be reported within the 7-day (DOA) grace period. If reported after 7 days, customer will be only responsible for shipping and handling fees. If reported after 30 days of receipt, customer is responsible for cost of the parts and shipping & handling fees. DO NOT return any unauthorized items to Elite Screens, as they will be refused at shipper’s expense. The RMA number must be included on the outside label of your shipping box and shipping documents. Our warehouse is not authorized to accept returns without an RMA number on the shipping label. RMA numbers are valid for 45 days from the date of issue. *A new or refurbished replacement will be sent out to the customer depending on the type of purchase (new or refurbished) or based on stock availability. Please visit elitescreens.com for Warranty Support and Warranty Service information. 9

****** Page 10 ****** REMEMBER TO REGISTER YOUR WARRANTY AT WWW.ELITESCREENS.COM/REGISTER.HTM US & Canada Tech Support & Warranty Claim Please contact us at service@elitescreens.com or call +1877-511-1211 #3 Service Europe Tech Support & Warranty Claim Please contact us at service@elitescreens.eu or call +49-(0) 40-30392958 Asia Tech Support & Warranty Claim Please contact us at service@elitescreens.com.cn or call +86-(0) 755-8461-7989 Taiwan Tech Support & Warranty Claim Please contact us at service@elitescreens.com.tw or call +886-(02) 2747-8979 America: Elite Screens lnc 16410 Manning Way Cerritos, CA 90703 USA Tel: +1-562-483-8198 (877-511-1211) Fax: +1-562-483-8498 info@elitescreens.com elitescreens.com Asia: Elite Screens China Corp. Longxi Duimianling Industry Zone Longcheng Longgang District, ShenZhen GuangDong, China Tel: Fax: info@elitescreens.com.cn elitescreens.com.cn Taiwan: Elite Screens Taiwan Co. Ltd. No.38, Alley 22, Lane 66, Sec. 5 Nanjing E. Rd., Songshan District Taipei City 105, Taiwan (R.O.C) Tel: Fax: info@elitescreens.com.tw elitscreens.com.tw Europe: Elite Screens Europe GmbH Lübecker Straße 1 22087 Hamburg, Germany Tel: +49-40-30392494 Fax: +49-40-49219200 info@elitescreens.eu elitescreens.eu Elite Screens France S.A.S 11, Allée William Penn 92150 Suresnes, France Tel: +33-1-45064735 Fax: +33-1-45064735 pascale.dautemer@elitescreens.com Latin America Contact: erik.garcia@elitescreens.com East Asia Contact: info.ea@elitescreens.com India Contact: info.india@elitescreens.com Japan Contact: info.japan@elitescreens.com 10

****** Page 11 ****** 11

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL



ELITE SCREENS EVANESCE (01) PDF MANUAL

Leave a comment, question, review or page error below. Account not required.

This site uses Akismet to reduce spam. Learn how your comment data is processed.