Click here to download ELECTROLUX PLHV36W7CC (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** Electrolux OWNER’S GUIDE – Range Hood PLHV36W7CC READ AND SAVE THESE INSTRUCTIONS PLHV36W7CC O P/N 316137228 O (Pub. 5995392130)

****** Page 2 ****** Product Registration Register your Product The self-addressed PRODUCT REGISTRATION CARD should be filled in completelyt signed and retumed to ELECTROLUX Canada. This Owner’s Guide contains general operating instructions for your range hood and feature information forseveral models. Your range may not have all the described features Note: The instructions appearing in this Owners Guide are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when Installing. operating and maintaining any appliance Thank you for choosing this appliance. The information contained within this Owners Guide will instruct you on howto properly operate and care foryour range hood Please readthroughtheinformationcontained in your literature packtolearn more about your new appliance. Record Your Model and Serial Numbers Record in the space provided belowthe model and serial numbers found on the serial plate located on the right hand side of the range hood Model Number: Serial Number: Date of Purchase: 2

****** Page 3 ****** 1m portant Safety Instructions READ AND SAVE THESE INSTRUCTIONS Take care when using cleaning agents or detergents. Suitable for use in household cooking area CAUTION To reduce risk of fire and to properly exhaust air, be sure to duct air outside Do not vent exhaust air into spaces within walls or ceilings or into atticst crawl spacesj or garages CAUTION For General Ventilating use Only* Do Not use To Exhaust Hazardous Or Explosive Materials And Vapors. WARNING – TO REDUCE THE RISK OF FIREI ELECTRIC SHOCK* OR *NJURY TO PERSONS, OBSERVE THE FOLLOWING, a, Use this unit only in the manner intended by the manufacturer- If you have questionsr contact the manufacturer. bv Before servicing orcleaning unit, switch poweroffatservice panel and tockthe servicedisconnecting meansto prevent power from being switched on accidentally- When the service disconnecting means cannot be locked: securely fasten a prominent warning device, such as a tag* to the service panel WARNING TO REDUCE THE RSK OF A RANGE TOP GREASE FIRE av Never leave surface units unattended at high settings, Boifoverscausesmoking and greasyspilloversthat may ignite Heat oils slowly on low or medium settings. by Always tum hood ON when cooking at high heat orwhen cooking flaming foods. cv Clean ventilating fans frequently, Grease should not be allowed to accumulate on fan or filter, dy Use proper pan size. Always use cookware appropriate for the size of the surface element. WARNING -TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE* OBSERVE THE FOLLOW!NG SMOTHER FLAMES with a close-fitting cookie sheet: or metal then turn off the burner, BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately. EVACUATE AND CALL THE FIRE DEPARTMENT. NEVER PICK UP A FLAMING PAN -You may be burned. cy DO NOT USE WATER* including wet dishcloths ortowels —a violent steam explosion will result. dy Use an extinguisher ONLY if, 1. You know you have a Class ABC extinguisher, and you already know how to operate it. 2 The fire is small and contained in the area where it started 3. The fire department is being called. 4. You can fight the fire with your back to an exit. WARNING – TO REDUCE THE RISK OF FIREI ELECTRIC SHOCKI OR iNJURY TO PERSONS. OBSERVE THE FOLLOWING a) installation work and electrical wiring must be done byqualified person(s) in accordance with all applicable codes and standardsr including fire-rated construction b) Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipmentto prevent back drafting. Followthe heating equipment manufacturers gu ideline and safety standards such as those published by the National Fire Protection Association (NFPA)r and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE)$ and the local code authorities. c) When cutting or driiling into wall or ceiling do not damage electrical wiring and other hidden utilities. d) Ducted fans must always be vented to the outdoors. WARNING – TO REDUCE THE RESK OF FIRE USE ONLY METAL DUCTWORK A WARNING Electrical Shock Hazard – Can result in serious injury or death Disconnect appliance from electric power before servicing ff equipped, the fluorescent light bulb contains small amounts of mercury which must be recycled ordisposed of according to Local Stater and Federal Codes 3

****** Page 4 ****** Installation FOR RESIDENTIAL USE ONLY NOT TO BE INSTALLED OVER GAS GRILLS PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. INSTALLATION MUST COMPLY WITH ALL LOCAL CODES. IMPORTANT: Save these Instructions for the Local Electrical Inspector’s use. INSTALLER: Please leave these instructions with this unit forthe owner. OWNER: Please retain these instructions for future reference. Safety Warning: Turn off power circuit at the service entrance and lock out panel* before wiring this appliance. Requirement: 120 V 60 Hz 15 or 20 A Dimensions ww c w D Figure 1* Note• All dimensions are shown in inches. * Dimensions are given from base of hood to ceilingt and include clearance required for installation. Dimensions A (Range of adjustable ht) * B (Min. ht. with one cover)* C (ht. from glass to bottom)* W (widht) D (depth)* DD (depth of the cover)* WW (widht of the cover)* Weight 44 pounds Diameter of Transition 6″ 29 1/2 223/4 3 35 7/8 195/8 11 5/8 11 5/16 Diameter of exhaust Duct required 6′ Considerations before installing Hood 1 2 3 4 5 Grease filters are not mounted and are located inside the package with the hood Be sure to get them before disposing of your package For the most efficient air flow exhaustl use a straight run or as few elbows as possible CAUTION: Vent unit to outside of building, only. ff alEowed in your area, use metallic flex ducting only to connect rigid duct directly to transitions. COLD WEATHER installations should have an additional backdraft damper installed to minimize backward cold air flow and a nonmetallic thermal break to minimize conduction of outside temperatures as part of the ductwork The dampershoufd be on the cold air side of the thermal break The break should be as close as possible to where the ducting enters the heated portion ofthe house Hood installation height above cooktop is the users preference. The lower the hood abovethe cooktop, the more efficientthe capturing of cooking odors, grease and smoke. We recommend the hood be installed 30-36″ above the countertop The lower height may be inconvenient fortali people and large cooking vessels Check your ceiling height and the hood height maximum before you select your hood. 4

****** Page 5 ****** Tools required for installation Screwdriver (flat headi pozidrive n02 and torx 10) Alen key 4mm Electric drill with twist bit Ø 10 mm CEILING Upper Fastener Locati s min. 29 15/16″ o Celling Bracket trem Fastener Locations Figure 2 (j Hooks Preparation of mounting surface (Drywall) 1. Select a mounting height comfortable for the user and mark on wall behind cooktop 2. Mark center line of cooktop and draw vertical line from bottom of hood to the ceiling 3. Tape template, matching center-line and hood bottom as shown in Fig. 2Y Distance from bottom of template to the ceiling must be minimum 29 15/16% 4. Mark centers ofthe 6 fastener locationsthrough template on wall then remove template. 5. Mark wall with horizontal line 1 1′ above highest and 1 ” below lowest fastener location 6. Find studs behind drywall by tapping wall or using a stud finder Mark the center of the studs with a vertical tine to the right and left of the marked fastenerlocation Note: Each 2 x 6 must span at least 2 studs side to side 7. Cutout dryuall along marked lines. install each 2 x 6 between studs firmly flush with stud front. Make sure ail mounting screws will anchorto added lumber, Replace drywall and refinish. 8. Remark center line and hood bottom on same location as before and tape template on wall as in step 3 above 9. Mount2 mounting hookswith wood screws (supplied in mounting hardware kit) on locations marked on template. then remove template 10. install duct cover ceiling bracket to wall flush to ceiling with drywall anchors supplied 5

****** Page 6 ****** Installation Hooks Figure 3 Duct Figure 4 Appl iance Installation: 1. Hang hood on 2 mounting hooks through the rectangular cutouts on back of hood 2. Level the appliancel using a carpenters level across bottom of hood with leveling screws in rectangular cutouts 3. Secure hood with 2 screws on bottom and 2 on top. Leveling Screw Rectangular Cutouts Bottom Screws Leveling Screw Top Fixing Screws Fixing Collar 4. Connect ducting (Figure 4). Note. for blower serviceabilityi leave a gap of 1″ minimum between top of transition and sheet metal duct and cover gap with a starting collar wrapped around duct and transition- Locate collar screws so they fit into corner ofduct covers Secu re collarto transition and ductwith three sheet metal screws each Seal with duct tape. Be sure to locate screws below damper lines drawn on transition Mark onto exterior of transition the location of the damper within. Secure ducting to transition with three sheet metal screws each. Be sure to locate screws below damper lines drawn on transition Seal with duct tape. Note: Do not use duct smaller than the transition. Reardischarge: A 900 elbow may be installed immediately above the hood. For serviceabilityta mounting similar to the straight up discharge should be used 6

****** Page 7 ****** 112″ Conduit Junction Box Cover fixing screws Figure 5 Figure 6 Wiring to Power Supply WARNING! ELECTRICAL-GROUNDING INSTRUCTIONS THISAPPLIANCE IS FITTED WITHAN ELECTRICAL JUNCT*ON BOXWITH 3 WRES, ONE OF WHiCH (GREEN/YELLOW) SERVES TO GROUND THE APPLIANCE. TO PROTECT YOU AGAINST ELECTRIC SHOCK: THE GREENANDYELLOWWREMUSTBECONNECTEDTOTHEGROUNDING WRE IN YOUR HOME ELECTRICALSYSTEMANDITMUSTUNDER NO CIRCUMSTANCES BE CUT OR REMOVED. Warn ing: Turn off power ci rcu it at the service panel before wiring this unit. 1. 120 V 15 AMP branch circuit required. 2. Remove the junction box coven unscrewthe 4 screws that fix it to the body of the hood. 3. install the conduit connector (1/2″) in junction box. 4. Run 3 wires; black, white and green (wire gauge percode) in 1 [2″ conduit from service panel to junction box. 5. Connect black wire from service panel to black or red injunction box* white to white and green to green-yellowy 6. Close junction box cover. with its 4 screws. Check all light bulbs to make sure they are secure in their sockets, Turn power on in service panel. Check lights and blower operation per Care & Use section of this manual. install filters 7. Install duct cover as shown in Fig. 6 8. Fit the filters see Page 9. Rear discharge: A 900 elbow may be installed immediately above the hood. For serviceability* a mounting similar to the straight up discharge shown in Figure 4 should be used. 7

****** Page 8 ****** Use and Care Motor OFF button READ THE INSTRUCTIONS CAREFULLY BEFORE USING THE HOOD For satisfactory use of your hood: become familiarwith the various functions of the hood as described below Suction power 2 LED, this led is ON when suction power 2 is selected. o Suction power 3 LED, this led is ON when suction power 3 is selected. »1 2 ON button and motorsuction power selection button 1, 2, 3, 1,…. Suction power 1 LED, this led is ON when suction power 1 is selected. Intensive Suction power LED, this led is ON when the intensive suction power is selected. Light OFF button Light ON button Intensive Suction power button – this suction power will function for 10 mins. then the hood set again the preselected speed Figure 7 Grease Filter Saturation LED The Suction power 2 LED is marked with an F. This LED will flash to remind you when the grease filter needs to be cleaned after 40 hours use. Follow the instructions for cleaning filters in this booklet. Once the grease filters have been cleaned} reset the reminder by pressing Motor OFF button for about 3 seconds until you hear the signal (beep) Should the Suction power 3 LED starts to flash then push ON and power selection button and the Intensive Suction power button simultaneously for more than 3 seconds to stop flashes. Operating Instructions The blower should be turned on for about 5 minutes before cooking in order to establish air currents upward through the hood use the low speeds for normal use and the higher speeds for strong odors or fumes Minimize cross drafts which will reduce the effectiveness of the hood. 8

****** Page 9 ****** Hood Cleaning Figure 8 Lights replacement Figure 9 Turn off electric power to hood before removing light cover Light Light cover Figure 9 Be sure Eights are cool before cleaning the hood To Clean Filters The metal grease filters will last forever. They are made of anodized aluminum It is recommended that the filters be washed at least once a month; they can be washed by hand or in the dishwashec Drain waterthroug h edge holes and let each fitterdrythorough ty before replacing it To Remove The Metal Grease Filters Disconnect the hood from electricity Push clips towards the rear and pull the filters downward Disengage each filter from a side and remove it To Replace The Metal Grease Filters Reverse procedure To Clean Hood Surface For general caret wipe the outside of the stainless steel, white black or glass hood with sudsy water or household cleaners such as Fantastic@ or Formula 409% rinse well and dry with clean soft cloth to avoid water marks, Wipe and dry brushed stainless steel in the same direction as the grain Do not use abrasive products. To remove finger prints and give added shine use spray cleaners such as Stainless Steel Magic@ and ShimmerO NOTE: Turn blowerand lights off. Make sure the lights are cool. if new lights do not operate be sure lights are insetted correctly before calling service. Remove the light cover using a little flat screwdriver or similar tool as a lever, Remove the damaged light and replace with a new 12 Volt 20 Watt (maxim um) halogen light made for a G-4 base, Follow package directions and do not touch new light with bare handsy Reinstall the tight cover (snap into position) 9

****** Page 10 ****** RANGE HOOD WARRANTY Your range hood is protected by this warranty FULL ONE-YEAR WARRANTY LIMITED WARRANTY (Applicable to tho State of Alaska) WARRANTY PERIOD One year from original purchase date, Time periods listed above. THROUGH OUR AUTHORIZED SERVICERS, WE WILL: Pay all costs for repairing or replacing any parts of this appliance which prove to be defective in materials or workmanship. All of the provisions of the full and [mited warranties above and the exclusions listed below apply. THE CONSUMER WILL BE RESPONSIBLE FOR: Costs of service calls that are under NORMAL RESPONSIBILITIES OF THE CONSUMER.* Costs of the technician’s travel to the home and any costs for pick up and delivery of the appliance required because of service. In tho U.S.A.s your appiianoe is warranted by Eiecfroiux Homo Products Nonh America, a division of White Consolidated Inc. We authorize no person to change or add to any of our obiigations under this warranty. Our obligations for setvico and parts under this warranty must be performed by us or an authorized Electrolux Home Products North America servicer. In Canada, your appiianco is warranted by WCI Canada, Inc. *NORMAL RESPONSIBILITIES OF THE CONSUMER EXCLUSIONS IF YOU NEED SERVICE This warranty applies only to products in ordinary household use, and the consumer is responsible for the items listed below: 1 2 3. 4. 5. 6. Proper use of the appliance in accordance with provided with the pF0duot. Proper installation by an authorized servicer in acco$dance with instructions provided with the appliance and in accordance with alt iooal plumbing, eieotrical and/or gas codes. Proper connection to a grounded power suppty of sufficient voitage! replacement of blown fuses, repair of loose connections or defects in house wiring. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,etcv, which aæ not a part of the appliance when it was shipped from the factory. Damages to finish after installation. Replacement of fight bulbs and/0? fluorescent tubes (on models with these featues). This warranty does not cover the following: 1. 2 3. 4 CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY. NOTE: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you. Service calls which do not involve malfunction or defects in workmanship or materiaL or for appliances not in ordinary househo*d use. The consumer shall pay for such service calls. Damages calised by services peH0$med by serviceFs othe? than Electrolux Home Products North Ame?ica or its authoüod senjicers; use of pans other than genuine Eleotroiüx Home Products parts; obtained from persons other than such servicers; or externai causes such as abuse, misuse, inadequate power supply or acts of God Products with original serial numbers that have been removed ot altered and cannot be readily determined. Keep your bili of saley delivery slip, or some other appropriate payment record. The date on the bilf establishes the warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all receipts. This written warranty gives you specific legal rights. You may also have other rights that vary from state to state. Service under this warranty musi be obtained by contacting Electrolux Home Products: This warranty only applies in the 50 states of the U.S.A„ Puerto Rico, and Canada. Product features or specifications as described or iffustrated are subject to change without notice. wa$ranties are made by Electrolux Home Products Nonh America, a division of White Consolidated Industries, Inc. In Canada, your appliance is warranted by WCI Canada Inc. USA Electrolux Home Products North America PIO. Box 212378 Augusta, GA 309#7 03-U-Rl+02 Canada (English) (French) Electrolux Home Products North America 6150 McLaughlin Road Mississauga, OntaFi01 Canada L5R 402

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL



ELECTROLUX PLHV36W7CC (01) PDF MANUAL

Leave a comment, question, review or page error below. Account not required.

This site uses Akismet to reduce spam. Learn how your comment data is processed.