Click here to download ELECTROLUX EFT 535 (01) PDF MANUAL

PDF Content Summary:

****** Page 1 ****** Electrolux Montage- und Gebrauchsanweisung , Installatie- en gebruiksaanwijzing EFT 630 – EFT 635 EFT 530 – EFT 535 Notice d’utilisation et d’installation, Operating and Installation Instructions

****** Page 2 ****** Contents Safety warnings 32 For the installer For the user Description of the Appliance Extractor version Recirculation Version Control Panel Correct ventilation Maintenance and Care Cleaning the hood Metal grease filter Paper grease filter Charcoal filter Changing the light bulb Something Not Working 32 32 33 33 33 34 34 35 .35 .35 .36 . 36 36 37 Special accessories 37 Service and Spare Parts 38 Guarantee Conditions 39 Technical Specifications 40 Installation 40 Unpacking Fitting Electrical connection Mounting accessories included Wall unit mounting Wall mounting . 40 40 40 41 41 41 Before installing or using this appliance please read this instruction book carefully paying particular attention to the safety warnings on the following page. If you have any queries regarding this appliance please contact Customer Care for advice. Please keep this instruction book for future reference and pass it on to any future owner of the appliance. 31

****** Page 3 ****** Safety warnings For the installer When used as an extractor unit, the hood must be fitted with a 125mm diameter hose. Attention: The hose is not supplied and must be purchased separately. When installing the hood, make sure you respect the following minimum distance from the top edge of the cooking hob/ring surfaces: electric cookers gas cookers coal and oil cookers 600 mm 650 mm 800 mm min. The national Standard on fuel-burning systems specifies a maximum depression of 0.04 mbar in such rooms. The air outlet must not be connected to chimney flues or combustion gas ducts. The air outlet must under no circumstances be connected to ventilation ducts for rooms in which fuel-burning appliances are installed. The air outlet installation must comply with the regulations laid down by the relevant authorities. When the unit is used in its extractor version, a sufficiently large ventilation hole must be provided, with dimensions that are approxi- mately the same as the outlet hole. National and regional building regulations impose a number of restrictions on using hoods and fuel-burning appliances connected to a chimney, such as coal or oil room-heaters and gas fires, in the same room. Hoods can only be used safely with appliances connected to a chimney if the room and/or flat (air/environment combination) is ventilated from outside using a suitable ventilation hole approximately 500-600 cm2 large to avoid the possibility of a depression being created during operation of the hood. If you have any doubts, contact the relevant controlling authority or building inspector’s office. Since the rule for rooms with fuel burning appliances is “outlet hole of the same size as the ventilation hole”, a hole of 500-600 cm2, which is to say a larger hole, could reduce the performance of the extractor hood. If the hood is used in its filtering function, it will operate simply and safely in the above conditions without the need for any of the aforementioned measures. When the hood is used in its extractor function, the following rules must be followed to obtain optimal operation: — short and straight outlet hose — keep bends in outlet hose to a minimum — never install the hoses with an acute angle, they must always follow a gentle curve. €—, keep the hose as large as possible (preferably the same diameter as the outlet hole). Failure to observe these basic instructions will drastically reduce the performance and increase the noise levels of the extractor hood. For the user The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. Always cover lighted elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames. Also, when frying, keep the deep frying pan on the cooker top/cooker under careful control. The hot oil in the frying pan might ignite due to overheating. The risk of self-ignition increases when the oil being used is dirty. It is extremely important to note that overheating can cause a fire. Never carry out any flambé cooking under the hood. Always disconnect the unit from the power supply before carrying out any work on the hood, including replacing the light bulb (take the cartridge fuse out of the fuse holder or switch off the automatic circuit breaker). It is very important to clean the hood and replace the filter at the recommended intervals. Failure to do so could cause grease deposits to build up, resulting in a fire hazard. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance. WARNING – Ensure that the appliance is switched off before replacing the lamp to avoid the possibility of electric shock. 32

****** Page 4 ****** Description of the Appliance The hood is supplied as an extractor unit and can also be used with a filtering function by fitting one charcoal filter. • You will need an original Electrolux charcoal filter for this function (Available from your local Electrolux Service Force Centre). ONLY for: EFT 630 W/GB / 942 120 776 EFT 630 B/GB / 942 120 777 EFT 635 X/GB / 942 120 779 The cooker hood is supplied ready for use as a recirculation hood and may be used for extraction by removing the charcoal filter which has been fitted inside the cooker hood. Extractor version In this version fumes are extracted to the outside via a hose connected to the coupling ring. Attention: The hose is not supplied and must be purchased separately. In order to obtain the best performance the hose should have a diameter equal to the outlet hole. Recirculation Version The air is filtered through a charcoal filter and returned to the kitchen through the front grid. Move the lever to position F. You will need an original Electrolux charcoal filter for this function (Available from your local Electrolux Service Force Centre). To the outside Coupling ring (Bayonet and screw fitting) Fig. 1 – Extractor version Charcoal Filter Hos Front grid Lever Fig. 2- Recirculation version 33

****** Page 5 ****** Control Panel Best results are obtained by using a low speed for normal conditions and a high speed when odours are more concentrated. Turn the hood on a few minutes before you start cooking, you will then get an under pressure in the kitchen. The hood should be left on after cooking for about 15 minutes or until all the odours have disappeared. The control switches are located on the unit’s front panel: the light switch switches the hood lamp on and off the motor switch switches the motor on and off, enabling you to select one of the three different speeds. Correct ventilation If the cooker hood is to work correctly there must be an under pressure in the kitchen. It is important to keep the kitchen windows closed and have a window in an adjacent room open. Light switch Motor switch Fig. 3 – Control panel 34

****** Page 6 ****** Maintenance and Care The hood must always be disconnected from the electricity supply before beginning any maintenance work. Cleaning the hood Clean the outside of the hood using a damp cloth and a mild detergent. Never use corrosive, abrasive or flammable cleaning products. Never insert pointed objects in the motor’s protective grid. Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders. Only ever clean the switch panel and filter grille using a damp cloth and delicate detergents. It is extremely important to clean the unit and change the filters at the recommended intervals. Failure to do so will cause grease deposits to build up that could constitute a fire hazard. Metal grease filter (EFT 635-535) The purpose of the grease filters is to absorb grease particles which form during cooking and it must always be used, either in the external extraction or internal recycling function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. Removing the metal grease filter First pull the latches backwards (a), then extract the grille outwards (b). Hand washing Soak grease filters for about one hour in hot water with a little washing-up liquid added, then rinse off thoroughly with hot water. Repeat the process if necessary. Refit the grease filters when they are dry. Dishwasher Place grease filters in the dishwasher. Select most powerful washing programme and highest temperature, at least 650C. Repeat the process. Refit the grease filters when they are dry. When washing the metal grease filter in the dishwasher a slight discolouration of the filter can occur, this does not have any impact on its performance. Clean the inner housing using a hot detergent solution only (never use caustic detergents, abrasive powders or brushes). Warning • Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations. Latch – EFT 630 – EFT 530 Latch – EFT 635 – EFT 535 a b a a Fig. 4 -Removing the metal grease filter Latch Grid Latch Grease filter Stops Fig. 5 – 2 Paper Grease filter 35

****** Page 7 ****** Paper grease filter (EFT 630-530) The purpose of the grease filters is to absorb grease particles which form during cooking and it must always be used, either in the external evacuation or internal recycling function. The paper grease filter is very thin (approx. I mm) and positioned on the inside of its related support grille. The filter should be changed once a month. The grille should be cleaned with luke warm water and non-abrasive detergent when you change the filter. The grease filter can be ordered from your local Electrolux Service Force Centre. Opening the grille Open the latch and swing the grille downwards. To remove the grille, pull it forwards from the right and release it. Removing the filter Open the grille and remove the stops to take out the filter. Charcoal filter The charcoal filter should only be used if you want to use the hood in the recirculation function. To do this you will need an original Electrolux charcoal filter (available from your local Service Force Centre). The charcoal filter cannot be washed nor regenerated. The charcoal filter should be replaced every 12 months under normal use. Replacement filters are available from your local Service Force Centre. Fitting Remove the cover by rotating the knobs to 900, put the charcoal filter inside and fix it by rotating the knob to 900 then close the cover. To remove proceed in the reverse order. Always specify the hood model code number and serial number when ordering replacement filters. This information is shown on the registration plate located on the inside of the unit. The charcoal filter can be ordered from your local Electrolux Service Force Centre. Changing the light bulb Disconnect the cooker hood from the mains supply. Remove the grid or the metal grease filter. Replace the old bulb with a new one of the same type. Remount the grid or the metal grease filter. If the light does not come on, make sure the bulb has been inserted correctly before contacting your local Service Force Centre. Latch Grill 2 Fig. 5 – Paper Grease filter Knobs 900 Move the lever Latch Grease filter Stops knob Cover Charcoal filter to position F Fig. 6 – Charcoal Filter – Fitting 36

****** Page 8 ****** Something Not Working If your appliance fails to work properly please carry out the following checks. Symptom The cooker hood will not start. The cooker hood is not working The cooker hood has switched off during operation. Solution Check that: The hood is connected to the electricity supply. Check that a fan speed has been selected Check that: The fan speed is set high enough for the task. The grease filters are clean. The kitchen is adequately vented to allow the entry of fresh air. If set up for recirculation, check that the charcoal filter is still effective. If set up for extraction, check that the ducting and outlets are not blocked. The safety cut-out device has been tripped. Turn off the hob and then wait for the device to reset. If the hood has been installed below the heights indicated in the installation instructions the motor will cut-out frequently which will damage the hood. If after all these checks, the problem persists, contact your local Service Force Centre, quoting the model and serial number. Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. Special accessories Charcoal filter TYPE 10 E-Nr. 942 120 770 37

****** Page 9 ****** Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, contact your local Electrolux Service Force Centre by telephoning: 08705 929 929 Your telephone call will be automatically routed to the Service Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at Please ensure that you have read the section „Something Not Working” as the engineer will make a charge if the fault is not a mechanical or electrical breakdown even the appliance is under warranty. Please note that proof of purchase is required for in-guarantee service calls. Help us to help you Please determine your type of enquiry before writing or telephoning. When you contact us we need to know: Your name Address and post code Telephone number Clear and concise details of the fault Name and model of the appliance* E number* * This information can be found on the rating plate, which can be seen when the grease filters are removed. CUSTOMER CARE DEPARTMENT For general enquiries concerning your Electrolux appliance or for further information on Electrolux products, please contact our Customer Care Department by letter or telephone at the address below or visit our website at Customer Care Department Electrolux 55-77 High Street Slough Berkshire SLI IDZ 08705 950950 * calls to this number may be recorded for training purposes. 38

****** Page 10 ****** Guarantee Conditions Standard guarantee conditions We, Electrolux, undertake that if within 12 months of the date of the purchase this Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: The appliance has been correctly installed and used only on the electricity supply stated on the rating plate. The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s instructions. The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. All service work under this guarantee must be undertaken by an Electrolux Service Force Centre. Any appliance or defective part replaced shall become the Company’s property. This guarantee is in addition to your statutory and other legal rights. Home visits are made between and 5.30pm Monday to Friday. Visits may be available outside these hours in which case a premium will be charged. Exclusions This guarantee does not cover: Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or removable parts of glass or plastic. Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the European Community (EC) or European Free Trade Area. Appliances found to be in use within a commercial environment, plus those which are subject to rental agreements. Products of Electrolux manufacture which are not marketed by Electrolux. European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications: The guarantee starts from the date you first purchased your product. The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products. This guarantee relates to you and cannot be transferred to another user. Your new home is within the European Community (EC) or European Free Trade Area. The product is installed and used in accordance with our instructions and is only used domestically, i.e. a normal household. The product is installed taking into account regulations in your new country. Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances. France Germany Italy Sweden Senlis Nürnberg Pordenone Stockholm Slough +33 (0)3 44 62 20 13 +49 (0)800 234 7378 +39 (0) 800 117511 +46 (0)20 78 77 50 +44 (0) 1753 219898 39

****** Page 11 ****** Technical Specifications Model Dimensions (in cm): Height (cm) Width (cm) Depth (cm) Maximum absorbed power: Motor absorption: Lighting: Length of the cable: Electrical connection: EFT 630 – EFT 635 13 59,8 51 160W 1 x 120 W 1 x 40 W 150 cm 220 – 240 v Subject to change without notice. Installation Unpacking Check that the cooker hood has no damages. Transportation damages should immediately be reported to the company responsible for the transportation. Damages, faults and eventually missing details should immediately be reported to the retailer. Take care of the packing materials so that small children cannot play with them. Fitting The hood is to be mounted on the wall. When installed, the hood must be not less than 60 cm. above electric burners or 65 cm. above gas or mixed-fuel burners. The hood can be installed above these heights but for optimum performance it should be installed at the distance quoted for the appropriate heat source. Electrical connection (not for UK) Safety warnings for the electrician Before connecting the appliance to the power supply, check that the voltage indicated on the rating plate corresponds to the mains power supply available. Appliances fitted with a plug can be connected to any standard power socket within easy access. Should it be necessary to provide a fixed connection, the hood must only be installed by an electrician authorised by the local electricity board. When installing, a double pole switch with a distance of at least 3 mm between contacts must be provided. Fixed connection of the appliance must only be carried out by an authorised electrician. EFT 530 – EFT 535 13 49,8 51 160 w 1 x 120 w 1 x 40 w 150 cm 220 – 240 v • . Fitting EFT 630/GB – EFT 635/GB 13 59,8 51 180 w 1 x 120 W 2 x 40 w 150 cm 220 – 240 v Min Min 65 cm 60 cm Electrical connection for UK only Safety warnings for the electrician Connect the hood to the mains supply via a double pole switch which has 3 mm minimum separation between the contacts. The switch must be accessible at all times. The following is valid in the United Kingdom only: the wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black, the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. 40

****** Page 12 ****** Installation Mounting accessories included 4 screws 5 x 45 mm 4 wall plugs (brick fixing) Ø 8 mm 4 screws 4,2 x 35 mm I flange Ø 125 mm I allen spanner (for TORX screws) I screw 2.9 x 13 Wall unit mounting Make the holes on the bottom of the cupboard (2), using the drilling template (1). Make a hole for the exhaust pipe (4) if the hood is to be used in the extraction version (3). From inside the cupboard, insert the 4 supplied screws (5) and tighten them in the appropriate holes on the appliance. Wall mounting Mark a centre line on the wall (1). Fit the template onto the wall (2). Fix the drilling template to the wall. Make 3 Ø 8mm holes in the wall (3), 2 at upper points, I as desired at lower points. Insert the three Ø 8mm expansion plugs into the wall (4) (brick fixing only).. Insert 2 5×45 screws (5) but do not tighten them completely, hang the hood (6). Adjust the unit so that it is positioned at a right angle to the wall by turning the two screws on lower side (7). Tighten the 2 upper screws (8). From inside the hood, insert the third 5×45 screw into the lower hole (9) and tighten (10). 3 4 5 2 1 5 5 2 3 5 4 3 Fig. 8 – Wall unit mounting 5! 5 6 7 4 fig 9- 6 7 10 8 . Wall mounting 41

****** Page 13 ****** 42

****** Page 14 ****** 43

****** Page 15 ****** Electrolux The Electrolux Group. The world’s No. 1 choice. The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world. O Electrolux plc 2003 Li12QB Ed. 03/03








Leave a comment, question, review or page error below. Account not required.

This site uses Akismet to reduce spam. Learn how your comment data is processed.