ELECTROLUX ANIMAL 800 (01) PDF MANUAL

Accessories may vary from model to model.

It takes approximately 2.5 hours to fully charge the battery.

The battery level is indicated by LED lights on the unit:

4 lights: 100% charged

3 lights: 75-100% charged

2 lights: 50-75% charged

1 light: 25-50% charged

1 flashing light: 0% charged

The compatible charger models are ADC-42FMG-35 35042EPG and ADC-42FMG-35 35042EPB.

1. Attach the tube to the main handheld unit until it clicks.

2. Attach the desired floor nozzle to the end of the tube until it clicks.

Accessories like the crevice tool or brush can be attached directly to the handheld unit or to the end of the tube until they click into place.

1. Choose a suitable location on the wall near a power outlet.

2. Use the provided template (if available) or hold the mount against the wall and mark the screw hole positions.

3. Drill holes and insert wall plugs if necessary (depending on wall type).

4. Screw the wall mount securely to the wall.

5. Connect the charger cable to the wall mount.

You can store the vacuum cleaner by placing it on the floor stand (if included) or by hanging it on the installed wall mount. Accessories can often be stored on the floor stand or wall mount as well. Ensure the vacuum is switched off before storing.

1. Detach the handheld unit from the tube (if attached).

2. Press the release button to detach the dustbin from the handheld unit.

3. Hold the dustbin over a trash receptacle.

4. Open the dustbin lid (usually via another release button or latch).

5. Empty the contents into the trash.

6. Close the lid securely before reattaching the dustbin.

Ensure you do not fill the dustbin beyond the Max line.

1. Empty the dustbin.

2. Remove the filter assembly from the dustbin.

3. Separate the pre-filter (mesh or cyclone part) from the fine dust filter.

4. Tap the filters gently to remove loose dust.

5. The pre-filter and fine dust filter can be rinsed under lukewarm tap water (Max 40°C). Do not use detergents.

6. Shake off excess water and allow the filters to air dry completely for at least 24 hours before reassembling and putting them back into the vacuum. Ensure they are completely dry.

Filters should be cleaned regularly for best performance. The fine dust filter should be washed periodically (e.g., monthly, depending on usage). It is recommended to replace the fine dust filter every 6 months (6M) to 1 year (1Y), depending on usage.

1. Turn off the vacuum cleaner.

2. Detach the floor nozzle from the tube.

3. Locate the brush roll release mechanism (usually a latch or button on the side of the nozzle).

4. Remove the brush roll from the nozzle housing.

5. Use scissors or your fingers to carefully remove tangled hair, threads, and debris from the brush roll and its end caps.

6. Some models feature a Brush Roll Clean function: Reassemble the vacuum, turn it on, place the nozzle on a hard floor, and press the Brush Roll Clean pedal on the nozzle for 5-30 seconds. Blades inside will cut the hair/fibers.

7. Wipe the brush roll and the inside of the nozzle housing clean if needed.

8. Reinsert the brush roll correctly into the nozzle housing until it clicks into place.

1. Turn off the vacuum cleaner.

2. Detach the PetPro+ nozzle.

3. Locate the release mechanism for the brush roll.

4. Remove the brush roll.

5. Remove tangled hair and debris using scissors or your fingers.

6. Wipe the brush roll and housing clean.

7. Reinsert the brush roll until it clicks into place.

1. Attach the cleaning pads (standard or delicate) to the bottom of the mop nozzle.

2. Open the water tank cap.

3. Fill the tank with clean water only (Max 40°C). Do not use detergents or hazardous liquids.

4. Close the cap securely.

5. Attach the water tank to the mop nozzle.

6. Attach the mop nozzle to the vacuum tube until it clicks.

7. Turn on the vacuum. The pads will rotate and dampen the floor as you vacuum.

1. Detach the pads from the mop nozzle.

2. Rinse the pads under water or wash them by hand or in a washing machine (Max 40°C).

3. Do not use fabric softener.

4. Allow the pads to air dry completely before reuse.

1. Press the ON/OFF button to start or stop the vacuum cleaner.

2. Press the (-/+) button to cycle through the power modes: MIN, MID, TURBO.

3. Some models feature an AUTO mode. In AUTO mode, the vacuum automatically adjusts suction power based on the floor type detected.

4. The selected mode is usually indicated by lights on the control panel.

1. Check if the battery is empty and needs recharging.

2. Check if the dustbin is full and needs emptying.

3. Check if the filters are clogged and need cleaning.

4. Check the nozzle, tube, and hose inlet for any blockages. Remove any obstructions found.

5. Check if the brush roll in the nozzle is jammed with hair or debris. Clean the brush roll.

6. If using the Brush Roll Clean feature, ensure it’s used correctly and check if the brush roll is free afterward.

7. Ensure the nozzle is not completely sealed against a surface like a very thick carpet, preventing airflow.

Availability may vary. Some available accessories and kits include:

ESKW4 (900 923 436): Yearly performance Kit

KIT23 (900 923 383): Home and car kit

KIT22 (900 923 354): Duster kit

ZE150 (900 923 377): Battery – 2.5Ah

ZE155 (900 923 379): PetPro+ nozzle

ZE149 (900 923 380): BedProPower+ nozzle

ZE149A (900 923 381): BedProPowerUV+ nozzle

ZE157 (900 923 438): PowerPro mop nozzle

ZE158 (900 923 440): Standard pads (for mop nozzle)

ZE159 (900 923 442): Delicate pads (for mop nozzle)

ZE146 (900 923 361): Duster

ZE156 (900 923 369): PowerPro hard floor nozzle

Accessories can be purchased at http://www.shop.electrolux.com.