Click here to download ELECTRIQ EIQ-65UHDT2SMH (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** electriU USER MANUAL ULTRA HD SMART LED TV eiQ-50UHDT2SMH eiQ-55UHDT2SMH eiQ-65UHDT2SMH eiQ-75UHDT2SMH I-±DTV

****** Page 2 ****** CONTENTS SAFETY INFORMATION CONNECTION AND PREPARATION OF TV WHAT IS INCLUDED INSTALLATION OF LEGS WALL MOUNTING BUTTONS AND INTERFACE CONNECTING TO EXTERNAL DEVICES REMOTE CONTROL INSTALLATION OF BATTERIES INITIAL SETUP BASIC OPERATION SETTING OF STANDBY MODE SETTING THE INPUT SOURCE TV MENU PICTURE SETUP SOUND SETUP CHANNEL SETUP SETTINGS TIME LOCK LAUNCHER TV App MEDIA TECHNICAL SPECIFICATION SUPPORTED SIGNAL MODES SIMPLE TROUBLESHOOTING MANUFACTURER SUPPORT 2 3 6 6 6 7 8 10 12 13 13 14 14 14 15 15 16 17 18 19 19 20 20 20 21 22 23 24 25

****** Page 3 ****** SAFETY INFORMATION Read these instructions All the safety and operating instructions should be read before this product is operated. Keep these instructions The safety and operating instructions should be retained for future reference. Heed all warnings —All warnings on the appliance and in the operating instructions should be adhered to. Follow all instructions —All operating and usage instructions should be followed. Do not use this equipment near water — The appliance should not be used near water or moisture e.g. in a wet basement or near a swimming pool. Clean only with a dry cloth. Do not use solvents or petroleum based fluids. Do not block any ventilation openings. Do not install near any heat sources such as radiators, stoves or other apparatus (including amplifiers) that produce heat. Do not tamper with the supplied plug. This plug is a BS1363 standard plug. Protect the power cord from being walked on or pinched, particularly at the plug and at the point where they exit from the appliance. Only use attachments/accessories specified by the manufacturer. Unplug the apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus or it has been exposed to rain or moisture, it does not operate normally or has been dropped. Please keep the unit in a well ventilated environment. The TV should only be connected to a mains power supply with AC 100- 240/- 50/60Hz To prevent overload, do not share the same power supply socket with too many other electronic components. Do not place any connecting wires where they may be stepped on or tripped over. Do not place heavy items on the cable as this may cause damage Hold the main plug, not the wires, when removing from a socket. Unplug immediately and seek professional help if the plug or cable is damaged, liquid has spilt onto the set, if accidentally exposed to water or moisture, if anything accidentally penetrates the ventilation slots or if the set does not work normally. Do not remove the safety covers. There are no user serviceable parts inside. To avoid battery leakage, remove exhausted batteries from the remote control when not in use for a long period. Do not block ventilation slots on the back cover. The TV can be placed in a 3

****** Page 4 ****** cabinet but ensure there is at least 5cm (2″) clearance all around. Do not tap or shake the TV screen, this may damage internal components. At full volume, prolonged listening may damage the users hearing. Diagrams within the manual are for illustrative purposes only, and as such there may be differences to the actual product received. WARNING Never place a television set in an unstable location. A television set may fall, causing serious personal injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such as: Use cabinets or stands recommended by the manufacturer of the television. Only use furniture that can safely support the television set. Ensure the television is not overhanging the edge of the supporting furniture. Do not place the television on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the television to a suitable support. Do not place the television set on cloth or other materials that may be located between the television set and the supporting furniture. Educate children about the dangers of climbing on furniture to reach the television or its controls. If your existing television set is being retained and relocated, the same considerations as above should be applied. WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and objects filled with liquids, such as vases, shall not be placed on or next to the apparatus. WARNING The wall plug socket is used as a disconnection device and should remain readily accessible. CAUTION Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type. Batteries shall not be exposed to excessive heat such as direct sunlight, fire or the like. Used batteries should be recycled appropriately. CAUTION To reduce the risk of electric shock, DO NOT remove the cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. 4

****** Page 5 ****** ATTENTION 10 cm Place the TV on a firm and flat surface, leaving a space of at least 10cm around the set and 30cm from the top of the set to the ceiling or cabinet. Ensure the TV is positioned close to the wall to avoid it falling when pushed. When lifting the TV, do not use one hand to handle it, you should lift the TV using two hands, ensuring pressure is not put on the screen itself. 5 30 cm 10 cm 10 cm When twisting the TV set, do not hold the top of the TV, you should twist from the base.

****** Page 6 ****** CONNECTION AND PREPARATION OF THE TV WHAT IS INCLUDED TV Set 4 Bolts INSTALLATION OF LEGS Remote Control (2 x AAA Batteries) 1 Place the TV with the front facing downwards on a soft cloth pads on a desk. 2 Insert the legs into the sockets on the base of the TV. 3 Insert the screws into the sockets and tighten them with a screwdriver. Do not use an electric screwdriver, or similar. 2 Legs løø gal o 0 electri(.å I-EOTV User Manual 0

****** Page 7 ****** WALL MOUNTING The TV is provided with mounting holes for a VESA approved wall mounting bracket (not supplied). The VESA mounting pattern is 50 Inch- 200x200mm and the size of the bolts for the top holes is 2 x M6 x 12(not supplied). The size of the screws for the bottom holes is 2 x T4 x 8(Supplied) 55 Inch- 200x200mm and the size of the bolts for the top holes is 2 x M6 x 12(not supplied). The size of the screws for the bottom holes is 2 x T4 x 8(Supplied) 65 Inch- 400x400mm and the size of the bolts is 4 x M6 x 12(not supplied). 75 Inch- 600x400mm and the size of the bolts is 4 x M8 x 25(not supplied). Do not use bolts longer than the size specified above for your model or damage will occur to the internal components. NOTES: Do not install this product until this manual has been read and understood thoroughly. Please keep these instructions for future reference. Due to the heavy weight and dimensions of the LCD screens and their fragile nature, we recommend that they are unpacked and assembled by 2 people and professional installers are used to wall mount them (Wall mounting is optional). If you do not understand the instructions, or are unsure how to install this product, please contact a professional for assembly advice and assistance. Careful consideration should be made regarding the location the television is to be wall mounted as some walls are not suitable for installation. If the television is to be mounted on drywall, the mount must be anchored into a wooden stud, concrete block or brick behind the drywall. Installing on drywall alone will not support the weight of the display. When drilling holes it is particularly important to take care of electrical cables, water or gas pipes in the wall. Please follow the instructions provided by the wall bracket manufacturer and ensure that all fixing screws supplied are used. electriQ and its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases any guarantee will expire. 7

****** Page 8 ****** 50″ and 55″ BUTTONS AND INTERFACE (SEE FOLLOWING PAGE FOR 65″ AND 75″) 2 4 5 6 7 8 9 MENU 3 or 4 5 6 7 8 9 10 RF IN RJ45 or 3 HDMII 2 HDM13 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. pr or 2 Remote Sensor Power Indicator Speaker Menu Button Program + Button Program — Button Volume + Button Volume — Button Source Button Standby Button Power Lead USB I/USB 2 RJ45 Network Port HDMI 1 HDMI 2 HDMI 3 Headphone Outpur AV Input RF IN (T 2) YPbPr (Component) Input OPTICAL Output USB2 USBI 5V 500mA HDM12 EARPHONE OPTICAL VIDEO

****** Page 9 ****** 65″ and 75″ BUTTONS AND INTERFACE (SEE PREVIOUS PAGE FOR 50″ AND 55″) 2 4 5 6 7 8 9 10 (jj 3 RJ45 or 4 5 6 7 8 9 10 HDMII or 3 2 EARPHONE PC(VGA) G 9 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. or 2 Remote Sensor Power Indicator Speaker Menu Button Program + Button Program — Button Volume + Button Volume — Button Source Button Standby Button Power Lead RJ45 Network Port HDMI 1 HDMI 2 VGA (PC) Input PC Audio Input AV Input RF / Aerial Input YPbPr (Component) Input Headphone / Speaker Out Optical Output USBI / 2 pr HDM12 OPTICAL PCAUDIO G USB2 USBI 5V 500mA VIDEO

****** Page 10 ****** 50″ and 55″ CONNECTING TO EXTERNAL DEVICES (SEE FOLLOWING PAGE FOR 65″ AND 75″) RJ4S Audio Amp or O O Soundbar coaxial cable cable W company HDMI cable Router Composite Component cable cable DVD Player oo cable receiver/satellite box

****** Page 11 ****** 65″ and 75″ CONNECTING TO EXTERNAL DEVICES (SEE PREVIOUS PAGE FOR 50″ AND 55″) Audio Amp or O 0 Soundbar coaxial cable cable W company R’45 Router VIOEO HDMI cable Composite Component cable cable DVD Player 00 cable receiver/satellite box 11

****** Page 12 ****** REMOTE CONTROL STANDBY SOURCE 4 6 5 11 13 1 19 21 2 23 2 2 28 31 3 FAV.LIST SUBTITLE AUDIO RECORD MIX TIMESHIFT 1 4 7 DISPLAY SIZE HOLD CANCEL REVEAL SU ENTER MUTE TV/RADIO 2 5 8 EPG CH 3 6 9 RECALL 1 14 16 18 20 24 2 2 33 l. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. STANDBY: Turn the TV On/Off SOURCE: Select the signal source GREEN: Access the green item or page YELLOW: Access the yellow item or page. RED: Access the red item or page. BLUE: Access the blue item or page. MOUSE: Turn the remote control mouse On/Off. HOME: Return to homepage. EXPLORER: Launch internet browser. TX T: Enter or exit teletext. FAV.LIST: Favourite channel list. MIX (within TX T): Setting transparency. RECORD: DTV mode record to USB stick. SUBTITLE: DTV mode select subtitle mode. SIZE (within TX T): Sets size of the characters. AUDIO: Select TV audio mode. CANCEL (within TXT): Cancel the TXT on screen. INDEX: Display the index page. (MEDIA mode): Fast rewind SUBPAGE: Enter sub page mode. * (MEDIA mode): Next file or chapter. HOLD: Hold the current page. (MEDIA mode): Fast forward. REVEAL: Reveal hidden information (MEDIA mode): Previous file or chapter. MENU: Enter or exit menu. EXIT: Exit the menu or current operation. DIRECTION BUTTONS: used for menu navigation. ENTER: Confirm or Enter. TIMESHIFT (Within DVR): Timeshift (MEDIA mode): Press to pause / play. EPG: Enter or exit the electronic program guide. O(MEDIA mode): Press to stop playback. VOL+: Increase the volume. CH A: Next channel. MUTE: Mute the sound. VOL -: Decrease the volume. CH V: Previous Channel. TV/RADIO: Change between TV or radio mode 0-9: Press the buttons to select a channel DISPLAY: Display the information for the current video / audio. RECALL: Return to previous channel.

****** Page 13 ****** INSTALLATION OF BATTERIES 1 2 3 Remove the battery cover from the rear of the remote control. Install two AAA 1.5V batteries. (Ensure the correct polarity of the batteries.) Replace the battery cover. Please take out of the batteries from the remote when it is not going to be used for a long period of time. If the remote control doesn’t work properly, please carry out the following checks. Check the TV is turned on. Check the polarity of the batteries are correct. Check the batteries and replace if necessary Check the plug is fully inserted and the socket is switched on. Check there are no special fluorescent light or neon light which could interfere with remote signals. INITIAL SETUP 2 1. 2. 3. 4. 1 Connect your TV to the power outlet. Connect your aerial and/or set top box to the television. Press the POWER button on the remote to turn on the TV. CAUTION: Always disconnect the TV from the power outlet when the TV will not be used for a long period of time. The POWER button on the television and remote is only used for switching the TV into standby and does not disconnect the device from the mains voltage. To completely disconnect the mains voltage, please remove the plug from the socket. Use the V/A/< / buttons on the remote to follow the setup guide on screen. 13 ****** Page 14 ****** BASIC OPERATION STANDBY MODE Press the STANDBY button to turn on the television. Press the STANDBY button again to return the television to standby mode. The power indicator will turn red. Be sure not to set your TV in standby mode for a long period of time. SELECT THE INPUT SOURCE USING THE REMOTE: Press the SOURCE button to display the input source list. Use the A and V buttons to select the input. Press the ENTER button on the remote to confirm USING THE TV CONTROLS: Press the SOURCE button repeatedly to scroll through the input source list ****** Page 15 ****** •rv MENU Press the MENU button to display the main menu. The menu is split into 6 sub menus: Picture Sound Channel Setting Time Lock Use the < and buttons to change between the sub menus. Once the required sub menu has been selected, use the A and V buttons to select the setting within the sub menu to change. Then use the < and buttons to amend the values. The MENU button can be pressed to navigate back a level in the menu, and the EXIT button can be used to exit the menu. PICTURE SETUP 9' (.•lvrg Picture Mode Vivid Picture PC Setting Color Temperature Aspect Ratio Noise Reduction MPEG NR Cold 16.•9 Middle Weak Choice of 8 different picture modes: Standard, Soft, User, Game, Vivid, Natural PICTURE Sports and Lightness. Individual picture settings are locked within each of the MODE modes apart from User. Within the User Picture mode the Contrast, Brightness, Hue, Sharpness and Saturation can be edited amend other settings, allowing the picture to be set to the users requirements. COLOR TEMPERATURE Used to set the colour temperature which is most comfortable. ASPECT RATIO NOISE REDUCTION MPEG NR Used to select the picture scale viewing mode required Used to reduce noise and improve picture quality Used to smooth the screen to reduce noise and improve image quality. 15 ****** Page 16 ****** SOUND SETUP Sound Sound Mode Bass Treble EQ Setting Balance Auto Volume AD Switch SOUND MODE EQ SETTING BALANCE AUTO VOLUME AD SWITCH HEARING IMPARED SURROUND SPDIF MODE 50 50 Standard Off Sound Balance Auto Volume AD Switch AD Volume Hearing Impaired Surround SPDIF Mode Off Off Off PCM Select the sound mode required. When set to User, the bass and Treble can be amended. Press to enter the equaliser to adjust the gain on individual frequency ranges. Ad'ust the balance of the out ut between the left and ri ht s eakers. Turn the auto volume control On / Off. When turned on if the volume exceeds a set value, it will be automatically reduced to protect the speakers / amplifier. Designed for eo le with visual im airment. This setting will make changes to the sound, improving the experience for users with hearing impairment. Turn surround sound On / Off Select the Coaxial output mode. 16 ****** Page 17 ****** CHANNEL SETUP Channel Antenna Type LCN Auto Tuning DTV Manual Tuning ATV Manual Tumnq Program Edit Signal Information Select the Antenna type between Air / Cable Select whether to use LCN to sort the channels. Choose the Automatic search in the submenu, select your country, the TV will then search for all channels currently available in your ANTENNA TYPE LCN AUTO TUNING DTV MANUAL TUNING PROGRAM EDIT SIGNAL INFORMATION area. Enter the sub menu to make changes to the tuning for individual channels. DTV Manual Tuning CH5 Frequency(Khz) Search Signal Strength Signal Quality DTV: DATA: o 177.50 MHz DIO: O Use the A and V buttons to select the channel you wish to edit. The selected channel can be moved, deleted, jumped, or added to modify your channel list. Displays information about the Strength and quality of the signal for each channel. 17 ****** Page 18 ****** SETTINGS Setting OSD Language Audio Language 2nd Audio Language Subtitle Subtitle Language 2nd Subtitle Language Teletext Language OSD LANGUAGE AUDIO LANGUAGE 2ND AUDIO LANGUAGE SUBTITLE SUBTITLE LANGUAGE 2ND SUBTITLE LANGUAGE TELETEXT LANGUAGE PVR FILE SYSTEM ENVIRONMENT BLUE SCREEN RESET English English glish Off nglish En West Set the OSD language. Set the audio language. Setting Subtitle Language 2nd Subtitle Language Teletext Language PVR File System Environment Blue Screen Reset English Englis West Home Mode Set the 2nd audio language. Turn subtitles On/Off. Set the ISt language for subtitles. Set the 2nd language for subtitles. Sets the language for teletext. Sets the file system used when recording within the PVR. Change the mode between "HOME MODE" and "SHOP MODE" Turn the blue screen (when no reception) on and off. Reset the TV to factory defaults. A dialogue box will request confirmation before reset. 18 ****** Page 19 ****** TIME Date / Time Sleep time Menu Time Standby Time LOCK Lock System Set Password Block Program Parental Guidance Button Lock Hotel Mode Time Date Current Time Sleep Time Menu Tin-te Standby Time 2017/01/01 92.02:2a Off Seconds 4 Hours Shows the current date and time Allows the system sleep time to be set. Select how long the menu will be displayed on the screen without input Select how long until the TV goes into standby when no input. Lock Lock System Set Password Block Program Parental Guidance Key Lock Hotel Mode Off Allows the system lock to be activated and deactivated. Enter to set a password for the lock Enter to select a program to block. Enter to set the parental guidance level. Press to lock the controls Enter to set Hotel Mode 19 ****** Page 20 ****** LAUNCHER Press the HOME button on the remote to enter the launcher. Press the DOWN button to select the icons at the bottom of the screen, then use the left and right buttons to move between the TV, APP and MEDIA sections of the launcher. Once the required section has been chosen, press the UP button to enter the section Press the EXIT button to exit the launcher. TV SECTION Use the left and right buttons to change between the different input sources. Press the ENTER button on the remote to select the input source in the centre of the screen. 01-01 HDM12 APP SECTION A pp •o All app DTV ATV Browser AV 01:55 Setting ALL APP FILE BROWSER SETTING View all apps installed on the TV Open the File manager to view files saved on the TV Use to access the internet. Access and modify the Android settings. 20 ****** Page 21 ****** SETTING Network Apps Device Network Preferences Apps 10 Storage & reset Storage and reset About Date and Time Language Keyboard MEDIA MEDIA Configure Network Settings View and remove apps installed on the TV Gives storage information and the option to reset SMART features to factory defaults System Info You can make the adjustment to the date and time; You can change the language that is displayed Configure the keyboard 02:18 01-01 o Video Audio Picture Within Media you can view Video, Audio and Pictures that have been saved to the TV or inserted memory stick. 21 ****** Page 22 ****** TECHNICAL SPECIFICATION Product Model Screen Size Aspect Ratio Power Supply Power Consumption TV System Audio Output Power 50UHDT2SMH 50" Diagonal 120W 55UHDT2SMH 55" Diagonal eiQ- 65UHDT2SMH 65" Diagonal 16:9 AC 100-240V, 50/60Hz 160W 220W eiQ- 75UHDT2SMH 75" Diagonal 320W PAL BIG D/K I,SECAM BIG D/K DVB-T/C/T2 (There is no DVB-C signal in some Countries or Areas.) NO NO 8Wx2 xl xl xl xl xl NO NO NO NO xl NO NO xl NO ooc 20% 80% Non-condensing xl xl 3 o (Internal) Antenna Input USB Input HDMI Input VGA Input PC AUDIO Input Audio Input ( L/R) Video Input YPbPr Input RJ45 Input Cl card In SCART In/Output DC In (12V) CARD SLOT Earphone Audio Line Out( Video Output Optical Coaxial out Working Temperature Working Humidity Note: Due to continued product development the specification shown above may change without notice. 22 ****** Page 23 ****** SUPPORTED SIGNAL MODES YPbPr MODE Resolution 480i 480p(720×480) 576i 576p(720×576) 720p(1280×720) 1080i 1080P(1920×1080) HDMI MODE Resolution 480 576 720 1 080i 1080p(1920×1080) 2160p(3840×2160) 2160 38402160 Horizontal Frequency (Khz) 15.734 31.468 15.625 31.25 37.50 45.00 28.13 33.75 67.50 56.25 Horizontal Fre uenc 31 .468 31 .25 45.00 33.75 67.50 67.50 135.00 Khz Vertical Frequency (Hz) 59.94 59.94 50.00 50.00 50.00 60.00 50.00 60.00 60.00 50.00 Vertical Fre uenc 59.94 50.00 60.00 60.00 60.00 30.00 60.00 When the signal received by the display is not within the allowed range, a warning message will appear on the screen. You can confirm the input signal format onscreen. VGA MODE (65" and 75" only) Resolution 640 x 480 800 x 600 1024 x 768 1366x 768 1920x 1080 Horizontal Frequency (Khz) 31 .50 35.16 37.90 48.40 47.85 67.50 Vertical Frequency (Hz) 60.00 56.25 60.00 60.00 60.00 60.00 Memo Full HD panel only Note: It is advised to use the VGA cable with a maximum length of 5 meters to maintain picture quality. 23 ****** Page 24 ****** SIMPLE TROUBLESHOOTING If the display fails or the performance changes dramatically, check the display in accordance with the following instructions. Remember to check the peripherals to pinpoint the source of the failure. Symptom Power cannot be turned on. (Power indicator does not illuminate.) No Input Signal message appears. The remote control does not function properly. Flashing spots or stripes appear on the screen. Image colour or quality deteriorates. Screen position and size are incorrect. Image or colour is incorrect. Display warning message. Solution -Check that both ends of the power cable are plugged into the socket appropriately and the wall socket is operational -Check that the aerial cable is connected properly. -Check that the power of the relevant peripherals is turned on. -Check that the selected source matches the input. -Check the batteries are not drained.(Use new batteries.) -Check that the remote control is within the operating range. -Check that the remote control is pointed to the remote control window on the display. -Check that there are no obstacles between the remote control and the remote control window. -Check that there are no emission (Car, HV cable or Neon lamp) or other possible interference sources. -Check that all the video settings are adjusted appropriately, such as brightness, contrast, colour etc. -For more information about video settings, refer to OSD Functions -Check that the screen position and size is adjusted appropriately. -Check that the signal line is connected properly. -When connecting to a PC, you can change the resolution of the PC to acquire the correct image. The discrepancy of the PC output signal may affect the display of the image. -Check that the input signal line is properly fixed. -Select the correct input signal. -For more information, refer to Supported Signal Modes ****** Page 25 ****** PRODUCT DISPOSAL Do not dispose this product as unsorted municipal waste. Collection of such waste must be handled separately as special treatment is necessary. Recycling facilities are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to participating civic amenity sites run by their local councils. Please remember that this equipment will be further handled during the recycling process, so please be considerate when depositing your equipment. Please contact the local council for details of your local household waste recycling centres. electriQ UK SUPPORT Complete online support form on electriQ.co.uWsupport Service Line: 0871 620 1057 Office hours: 9AM 5PM Monday to Friday Unit J6, Lowfields Business Park, Lowfields Way, Elland West Yorkshire, HX5 9DA 25

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL



ELECTRIQ EIQ-65UHDT2SMH (01) PDF MANUAL

Leave a comment, question, review or page error below. Account not required.

This site uses Akismet to reduce spam. Learn how your comment data is processed.