Click here to download ELATION PROFESSIONAL SIXPAR 300 (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** PROFESSIONAL .oQo ooo o oÖo QÖo• SIXPAR 300TM User manual z

****** Page 2 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL elationlighting.com 02015 ELATION PROFESSIONAL all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ELATION PROFESSIONAL logo and identifying product names and numbers herein are trademarks of ELATION PROFESSIONAL, Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged, All non-ELATION brands and product names are trademarks or registered trademarks of their respective companies, ELATION PROFESSIONAL and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and operation of this product, Elation Professional USA | 61 22 S, Eastern Ave, I Los Angeles, CA, 90040 323-582-3322 | 323-832-9142 fax I elationlighting.com I info@elationlighting.com Elation Professional B.V, I Junostraat 2 | 6468 EW Kerkrade, Netherlands +31 45 546 85 66 | +31 45 546 85 96 fax I elationlighting.eu I info@elationlighting.eu DOCUMENT VERSION Please check elationlighting.com for the latest revision/update of this manual. Document Version DMX Software Channel Modes Date 2/2015 Version 21.02 6/7/8/12 Initial release, 2 Notes SIXPAR 300TM User Manual Ver. I

****** Page 3 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL General Information Warranty Safety Instructions General Guidelines Fixture Overview Fixture Installation Understanding DMX Fixture Menu elationlighting.com DMX Channel Functions And Values Cleaning and Maintenance Technical Specifications Optional Accessories 3 4 6 7 8 9 10 12 15 18 21 22 24 SIXPAR 300TM User Manual Ver. I

****** Page 4 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL INTRODUCTION elationlighting.com Congratulations, you have just purchased one of the most innovative and reliable lighting fixtures on the market today! The SIXPAR 300TM has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit. These instructions contain important information regarding safety during use and maintenance, UNPACKING Thank you for purchasing the SIXPAR 300TM by Elation Professional@ Every SIXPAR 300TM has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your unit for damage and be sure all accessories necessary to operate the unit have arrived intact, In the event damage has been found or parts are missing, please contact our customer support team for further instructions. Please do not return this unit to your dealer without first contacting customer support at the number listed below, Please do not discard the shipping carton in the trash, Please recycle whenever possible. BOX CONTENTS (l) powerCON Cable Manual & Warranty Card 4 SIXPAR 300TM User Manual Ver. I

****** Page 5 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL CUSTOMER SUPPORT elationlighting.com Elation Professional@ provides a customer support line, to provide set up help and to answer any question should you encounter problems during your set up or initial operation. You may also visit us on the web at elationlighting.com for any comments or suggestions, For service related issue please contact Elation Professional@, ELATION SERVICE USA – Monday – Friday 8:OOam to 5:OOpm PST Voice: 323-582-3322 Fax: 323-832-9142 E-mail: support@elationlighting.com ELATION SERVICE EUROPE – Monday – Friday 08:30 to 17:00 CET Voice: +31 45 546 85 30 Fax: +31 45 546 85 96 E-mail: support@elationlighting.eu WARRANTY REGISTRATION Please fill out the enclosed warranty card to validate your purchase, All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (RIA,) number, The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A. number must also be written down on a piece of paper and included in the shipping container, If the unit is under warranty, you must provide a copy of your proof of purchase invoice. Items returned without a R.A. number clearly marked on the outside of the package will be refused and returned at customer’s expense. You may obtain a R.A. number by contacting customer support at 323-582-3322 IMPORTANT NOTICE! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself; doing so will void your manufactures warranty. Damages resulting from modifications to this fixture and/or the disregard of safety and general user instructions found in this user manual void the manufactures warranty and are not subject to any warranty claims and/or repairs. 5 SIXPAR 300TM User Manual Ver. I

****** Page 6 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL

elationlighting.com A, Elation Professional@ hereby warrants, to the original purchaser, Elation Professional@ products to be free of manufacturing defects in material and workmanship for a period of two years (730 days), and Elation Professional@ product rechargeable batteries to be free of manufacturing defects in material and workmanship for a period of six months (1 80 days), from the original date of purchase. This warranty excludes discharge lamps and all product accessories. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought. B. For warranty service, send the product only to the Elation Professional@ factory. All shipping charges must be pre-paid, If the requested repairs or service (including parts replacement) are within the terms of this warranty, Elation Professional@ will pay return shipping charges only to a designated point within the United States, If any product is sent, it must be shipped in its original package and packaging material. No accessories should be shipped with the product, If any accessories are shipped with the product, Elation Professional@ shall have no liability what so ever for loss and/or or damage to any such accessories, nor for the safe return thereof, C, This warranty is void if the product serial number and/or labels are altered or removed; if the product is modified in any manner which Elation Professional@ concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the Elation Professional@ factory unless prior written authorization was issued to purchaser by Elation Professional@; if the product is damaged because not properly maintained as set forth in the product instructions, guidelines and/or user manual, D, This is not a service contract, and this warranty does not include any maintenance, cleaning or periodic check-up. During the periods as specified above, Elation Professional@ will replace defective parts at its expense, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship, The sole responsibility of Elation Professional@ under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of Elation Professional@i All products covered by this warranty were manufactured after January 1, 1990, and bare identifying marks to that effect. E. Elation Professional@ reserves the right to make changes in design and/or performance improvements upon its products without any obligation to include these changes in any products theretofore manufactured. F, No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with the products described above, Except to the extent prohibited by applicable law, all implied warranties made by Elation Professional@ in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty periods set forth above And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said periods have expired. The consumer’s and/or dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall Elation Professional@ be liable for any loss and/or damage, direct and/or consequential, arising out of the use of, and/or the inability to use, this product, G. This warranty is the only written warranty applicable to Elation Professional@ products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published. 6 SIXPAR 300TM User Manual Ver. I

****** Page 7 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL SAFETY

INSTRUCTIONS elationlighting.com The SIXPAR 300TM is an extremely sophisticated piece of electronic equipment. To guarantee a smooth operation, it is important to follow the guidelines in this manual. The manufacturer of this device will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. This device falls under PROTECTION CLASS 1, It’s essential this device be grounded properly, Only qualified personnel should perform all electrical connections, A U I o N s KEEP THIS FIXTURE AWAY FROM RAIN AND MOISTURE! UNPLUG POWER BEFORE SERVICING FIXTURE NEVER TOUCH FIXTURE DURING OPERATION AS IT MAY BE HOT NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE SENSITIVE PERSONS MAY SUFFER AN EPILETIC SHOCK For proper operation, follow the Installation guidelines described in this manual. Only qualified and certified personnel should perform installation of this fixture and only the original rigging parts (brackets) included with this fixture should be used for installation, Any modifications will void the original manufactures warranty and increase the risk of damage and/or personal injury, Never look directly into the light source of this fixture to prevent risk of injury to your retina, which may induce blindness, Those suffering from EPILEPSY should avoid looking directly into the light source of this unit at all times. Always disconnect from main power source before performing any type of service and/or cleaning procedure. Only handle the power cord by the plug end, never pull out the plug by tugging the wire portion of the cord, Do not operate this fixture if the power cord has become frayed, crimped and/or damaged, If the power cord is damaged, replace it immediately with a new one of similar power rating 7 SIXPAR 300TM User Manual Ver. I

****** Page 8 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL elationlighting.com NEVER OPEN THIS FIXTURE WHILE IN USE! During the initial operation of this fixture, a light smoke or smell may emit from the interior of the fixture. This is a normal process and is caused by excess paint in the interior of the casing burning off from the heat associated with the lamp and will decrease gradually over time. This fixture is a professional lighting effect designed for INDOOR / DRY LOCATIONS ONLY on stage, in nightclubs, theatres, etc. Please make sure there are NO FLAMMABLE MATERIALS close to the fixture while operating, to prevent any fire hazard, Minimum distance of inflammable materials from the surface 1.6 feet (0.5m), DO NOT attempt installation and/or operation without knowledge how to do so. DO NOT allow operation by persons who are not qualified to operate this type of fixture, Most damages are the result of operations by nonprofessionals. Consistent operational breaks may ensure the fixture will function properly for many years to come, DO NOT shake fixture, avoid brute force when installing and/or operating fixture. Always install the fixture with an appropriate safety cable. When installing the fixture in a suspended environment, always use mounting hardware that is no less than MIO x 25 mm, also be sure the hardware is insert in the pre-arranged screw holes in the bracket of the fixture, Use the original packaging and materials to transport the fixture in for service. DO NOT TOUCH the housing bare-hand during its operation, Turn OFF the power and allow approximately 15 minutes for the fixture to cool down before replacing or serving, 8 SIXPAR 300TM User Manual Ver. I

****** Page 9 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL elationlighting.com 12 3456 9101112 2. 3. 5. 7. 10. 11. 12. Fuse powerCON IN MODE Button UP Button DOWN Button ENTER Button powerCON OUT LCD Menu Display 3Pin DMX IN 3Pin DMX OUT 5Pin DMX IN 5Pin DMX OUT SIXPAR 300TM User Manual Ver. I

****** Page 10 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL FIXTURE elationlighting.com INSTALLATION FLAMMABLE MATERIAL WARNING Keep fixture at least 5.0 ft (1.5m) away from any flammable materials, decorations, pyrotechnics, etc. A qualified electrician should be used for all electrical connections and/or installations. CAUTIONS For added protection, mount the fixture in areas outside walking paths, seating areas, or in areas were unauthorized personnel might reach the fixture, Min/Max ambient operating temperature for this fixture is 50F to 1 130F (-150C to 450C) Do not use the fixture under or above this temperature, Before mounting the fixture to any surface, make sure the installation area can hold a minimum point load of 10 times the weight of the fixture. 180 lbs / 81 kg) Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety cable. Never stand directly below the device when mounting, removing or servicing, POWER LINKING Max number of units that can be power linked is 5 units @1 IOV and 10 units @240V. CLAMP MOUNTING The SIXPAR 300TM provides a unique integrated Dual Yoke / Floor Stand. When mounting this fixture to truss be sure to secure an appropriately rated clamp using an MIO screw fitted through the center hole of the Dual Yoke / Floor Stand. SECURING Regardless of the rigging option you choose for your SIXPAR 300TM always be sure to secure your fixture with a safety cable. The fixture provides a built-in rigging point for a safety cable on the hanging bracket as illustrated above. Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle, 10 SIXPAR 300TM User Manual Ver. I

****** Page 11 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL MOUNTING POINTS elationlighting.com Overhead mounting requires extensive experience, including amongst others calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the device. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury. Fixture is fully operational in the specific mounting positions as illustrated below. 0 00 0 QÖe (JOO OoQoO OOD 00800 ooe oÖ ooÖ o Qöo• SAFETY CABLE Always use a Safety Cable whenever installing this fixture in a suspended environment to ensure the fixture will not drop if the clamp fails. SIXPAR 300TM User Manual Ver. I

****** Page 12 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL DMX-512 elationlighting.com DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers. DMX allows all makes and models of different manufactures to be linked together and operate from a single controller, This is possible as long as all the fixtures and the controller are DMX compliant. A DMX controller sends the DMX data instructions to the fixture allowing the user to control the different aspects of an intelligent light. DMX data is sent out as serial data that travels from fixture to fixture via data “IN” and data “OUT” XLR terminals located on the fixtures (most controllers will only have output jacks). DMX LINKING To ensure proper DMX data transmission, always use proper DMX cables and a terminator, When using several DMX fixtures try to use the shortest cable path possible, Never split a DMX line with a “Y” style connector, The order in which the fixtures are connected in a DMX line does not influence the DMX addressing, For example; a fixture assigned a starting DMX address of 1 may be placed anywhere in the DMX chain, at the beginning, at the end, or anywhere in the middle, The DMX controller knows to send data assigned to address 1 to that fixture no matter where it is located in the DMX chain. The SIXPAR 300TM can be controlled via DMX-512 protocol and the DMX address is set via the control menu. DATA CABLE (DMX Cable) REQUIREMENTS (For DMX and Master/Slave Operation) Your fixture and your DMX controller require a standard 3pin or 5pin XLR connector for data input and data output (see figure below), Also, remember that a DMX line must be daisy chained and cannot be split, SIXPAR 300TM User Manual Ver. I

****** Page 13 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL DMX-512 CONTROLLER CONNECTION elationlighting.com Connect the provided XLR cable to the female XLR output of your controller and the other side to the male XLR input of the SIXPAR 300TM The diagram below illustrates a typical DMX-512 connection when the fixture is in the 12 Channel Mode. You can chain multiple panels together through serial linking, Always be sure daisy chain your in and out data connections, never split or “Y” your DMX connections, ooe oÖ o oÖo Qöo• DMX CONTROLLER Address 1 ooe oÖ o oÖo Qöo• Address 13 ooe oÖ o oÖo Qöo• Address 25 DMX-512 CONNECTION WITH DMX TERMINATOR A DMX terminator should be used in all DMX lines especially in longer runs. The use of a terminator may avoid erratic behavior in your DMX line, A terminator is a 120 ohm 1/4 watt resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line. Using a line terminator will decrease the possibilities of erratic behavior, 1200 n I Termination reduces signal errors and avoids signal transmission problems and interference. It is always advisable to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3 (DMX +) of the last fixture. 13 SIXPAR 300TM User Manual Ver. I

****** Page 14 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL DMX ADDRESSING elationlighting.com All fixtures should be given a DMX starting address when using a DMX controller, so the correct fixture responds to the correct control signal, This digital starting address is the channel number from which the fixture starts to “listen” to the digital control information sent out from the DMX controller, The allocation of this starting DMX address is achieved by setting the correct DMX address on the digital display located on the back of the fixture, You can set the same starting address for all fixtures or a group of fixtures, or set different address for each individual fixture. Be advised that setting all fixtures to the same DMX address will subsequently control all fixtures in the same fashion, in other words, changing the settings of one channel will affect all the fixtures simultaneously, If you set each fixture to a different DMX address, each unit will start to “listen” to the channel number you have set, based on the quantity of control channels (DMX channels) of each fixture. That means changing the settings of one channel will only affect the selected fixture. In the case of the SIXPAR 300TM, when in the 12 Channel Mode you should set the starting DMX address of the first unit to 1, the second unit to 13 (1 + 12), the third unit to 25 (13 + 12), and so on. Note: During start-up the SIXPAR 300TM will automatically detect whether a DMX data signal is being received or not. If the fixture is not receiving a DMX signal please check the following: The 3pin or 5pin XLR input plug (cable with DMX signal from controller) is not connected or is not inserted completely into the DMX input jack of the fixture, The DMX controller is switched off or defective. The DMX cable or connector is defective, A DMX terminator has been inserted into the last fixture in your DMX chain. 14 SIXPAR 300TM User Manual Ver. I

****** Page 15 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL ON-BOARD SYSTEM MENU elationlighting.com The SIXPAR 300TM comes with an easy to navigate system menu. will cover how to access each menu function, LCD CONTROL PANEL DISPLAY The next sections The (4) button control panel (see image below) located on back of the fixture a lows you to access the main menu and make all necessary adjustments to the SIXPAR 300TM. During normal operation, pressing the MODE button will navigate through the different function menus. Once you reach a desired menu, press the ENTER button to select that menu. The variable field that can be adjusted within the selected menu will begin to flash. Using the UP or DOWN buttons, adjust the field until the desired value is displayed. For example, the CHANNEL CH: menu variable field can be set to 06, 07, 08, or 12. Pressing the ENTER button once will confirm your selected value. Exit at any time without making any adjustments by pressing the MODE button, MODE ADDRgj: DOWN ENTER INFORMATION DISPLAYED DURING INITIAL POWER ON When the fixture is initially powered ON, the display shows the following information: Update Wait… SIXPAR 300 15 100 VI .02 Fixture Software Version (Greater than or equal to) SIXPAR 300TM User Manual Ver. I

****** Page 16 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL LCD CONTROL PANEL LOCKOUT

When the Display ON menu is set to OFFL the LCD elationlighting.com display will turn OFF after 30 seconds and the (4) button Control Panel will be LOCKED. To unlock the (4) button LCD control panel follow these steps: 2. 3, 4. 5. 6. When locked, the display will show: Press UP, then the display will change to: LOCKED**** (one * disappears) Press DOWN, then the display will change to: LOCKED*** (two * disappear) Press UP, then the display will change to: LOCKED** (three * disappear) Press DOWN, then the display will change to: LOCKED* (4 * disappear) Press ENTER/ then the display will change to LOCKED and then become unlocked. ELATIONO SIXPAR SYSTEM MENU Specifications are subject to change without any prior written notice, MENU CHANNEL DMX MODE SLAVE MODE Display ON Internal Programs DimCurve NO DMX OPTIONS / VALUES CHI 06, 07, 08, 12 ADDR: OOI — 512 SALVE MODE ON OFF OFFI -MANUAL ROO-99 GOO-99 BOO-99 woo-99 UOO-99 soo-99 2.CHANGE SPOI -99 SOO-99 3.CHANG6 SPOI -99 SOO-99 4.FADE SPOI -99 soo-99 Standard, Stage, TV, Architect Theatre Blackout Hold Fade DESCRIPTION DMX Channel Mode DMX Address Setting Set Fixture A Slave Unit LCD Display Always ON LCD Display OFF after 30 seconds LCD Display OFF After 30 Seconds and LOCKED Manual Color Adjustment Adjust RED Brightness (00-99) Adjust GREEN Brightness (00-99) Adjust BLUE Brightness (00-99) Adjust WHITE Brightness (00-99) Adjust AMBER Brightness (00-99) Adjust UV Brightness (00-99) Adjust STROBE SPEED OO SLOW (0. I Hz) – 99 FAST (20Hz) 30 Color Chase Macro Adjust SPEED 01 SLOW – 99 FAST Adjust STROBE SPEED 00 SLOW (0.1 Hz) – 99 FAST (20Hz) 6 Color Chase Macro Adjust SPEED 01 SLOW – 99 FAST Adjust STROBE SPEED 00 SLOW (0.1 Hz) – 99 FAST (20Hz) Color Fade Macro Adjust SPEED 01 SLOW – 99 FAST Adjust STROBE SPEED OO SLOW (0.1 Hz) – 99 FAST (20Hz) Set Dimming Curve NO Output Hold Last Setting Fade SIXPAR 300TM User Manual Ver. I

****** Page 17 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL DIMMING CURVES

elationlighting.com The DimCurve menu allows you to select one of the following preset dimming curves: Standard, Stage, TV, Architec, or Theatre, (See diagram below for more details) Ramp Effect Standard Stage Architectural Theatre Dimmer 100% 780 1180 t 360 1580 OS (Fade Time) 1100 1520 1730 1940 1540 1860 2040 2230 IS (Fade Time) 1660 2120 2280 SIXPAR 300TM User Manual Ver. I

****** Page 18 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL

elationlighting.com ELATIONO SIXPAR DMX Channel Values / Functions (1 2 DMX Channels) Specifications are subject to change without any prior written notice, MODE / CHANNEL 6 CH 2 3 5 6 VALUE 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-31 32-95 96-127 128-159 160-191 192-223 224-255 FUNCTION 2 3 5 6 7 2 3 5 6 7 8 12 CH 2 3 5 6 7 8 RED Red (0-100%) GREEN Green (0-1000/0) BLUE Blue (0-100%) WHITE White (0-1000/0) AMBER Amber (0-100%) U. v. (0-100%) MASTER DIMMER Dimmer (0-100%) STROBE LED OFF (NO STROBE) Strobe Effect SLOW to FAST LED ON (NO STROBE) Strobe Pulse Effect In Sequences SLOW to FAST LED ON (NO STROBE) Random Strobe Effect SLOW to FAST LED ON (NO STROBE) 18 SIXPAR 300TM User Manual Ver. I

****** Page 19 ****** E’L¯ÅiiÖF’ 100-103 104-107 108-111 112-115 116-119 120-123 124-127 128-131 132-135 140-143 148-151 PPO”SS’ONAL

ELATION@ SIXPAR elationlighting.com DMX Channel Values / Functions (1 2 DMX Channels) Specifications are subject to change without any prior written notice, MODE / CHANNEL 12 CH 9 VALUE 0-3 4-7 12-15 16-19 20-23 24-27 28-31 32-35 36-39 40-43 44-47 48-51 52-55 56-59 60-63 64-67 68-71 72-75 76-79 80-83 84-87 88-91 92-95 96-99 FUNCTION COLOR MACROS OFF RED GREEN BLUE WHITE AMBER UV RED + GREEN RED + BLUE RED + WHITE RED + AMBER RED + UV GREEN + BLUE GREEN + WHITE GREEN + AMBER GREEN + W BLUE + WHITE BLUE + AMBER BLUE + UV WHITE + AMBER WHITE + UV AMBER + UV RED + GREEN + BLUE RED + GREEN + WHITE RED + GREEN + AMBER RED + GREEN + UV RED + BLUE + WHITE RED + BLUE + AMBER RED + BLUE + UV RED + WHITE + AMBER RED + WHITE + UV RED + AMBER + UV GREEN + BLUE + WHITE GREEN + BLUE + AMBER GREEN + BLUE + UV GREEN + WHITE + AMBER GREEN + WHITE + UV GREEN + AMBER + UV SIXPAR 300TM User Manual Ver. I

****** Page 20 ****** E’L¯ÅiiÖF’

PPO”SS’ONAL ELATION@ SIXPAR 300 TM 152-155 156-159 160-163 164-167 168-171 172-175 176-179 180-183 184-187 RED + GREEN + WHITE + UV 188-191 192-195 196-199 elationlighting.com DMX Channel Values / Functions (1 2 DMX Channels) Specifications are subject to change without any prior written notice, MODE / CHANNEL 7 CH 8 CH 12 CH 9 10 12 VALUE 200-203 204-207 208-211 212-215 216-219 220-223 224-227 228-231 232-235 236-239 240-243 244-247 248-251 252-255 00-20 21-40 41-60 61 -80 81-255 00-255 0-20 21-40 41 61-80 81-100 101-255 FUNCTION COLOR MACROS (continued) BLUE + WHITE + AMBER BLUE + WHITE + UV BLUE + AMBER + UV WHITE + AMBER + UV RED + GREEN + BLUE + WHITE RED + GREEN + BLUE + AMBER RED + GREEN + BLUE + UV RED + GREEN +WHITE + AMBER RED + GREEN + AMBER + UV RED + BLUE + WHITE + AMBER RED + BLUE + WHITE + UV RED + BLUE + AMBER + UV RED + WHITE + AMBER + UV GREEN + BLUE + WHITE + AMBER GREEN + BLUE + WHITE + W GREEN + BLUE + AMBER + UV GREEN + WHITE + AMBER + UV BLUE + WHITE + AMBER + UV RED + GREEN + BLUE + WHITE + AMBER RED + GREEN + BLUE + WHITE + UV RED + GREEN + BLUE + AMBER + UV RED + GREEN + WHITE + AMBER + UV RED + BLUE + WHITE + AMBER + W GREEN +BLUE + WHITE + AMBER + UV RED + GREEN + BLUE + WHITE + AMBER + UV COLOR CHASE MACROS NO Function 30 Color Chase 6 Color Chase Color Fade Chase NO Function COLOR CHASE MACROS SPEED Chase Speed of CHANNEL 10 – SLOW to FAST DIMMING MODES STANDARD STAGE ARCHITECTURAL THEATER NO Function 20 SIXPAR 300TM User Manual Ver. I

****** Page 21 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL CLEANING elationlighting.com O Disconnect power before cleaning or maintenance. Frequent cleaning is recommended to insure proper function, optimized light output, and an extended life. The frequency of cleaning depends on the environment in which the fixture operates: damp, smoky or particularly dirty environments can cause greater accumulation of dirt on the fixture’s optics. Clean the external lens surface at least every 20 days with a soft cloth to avoid dirt/debris accumulation. Never use alcohol, solvents, or ammonia based cleaners. MAINTENANCE Regular inspections are recommended to insure proper function and extended life, There are no user serviceable parts inside this fixture, please refer all other service issues to an authorized Elation service technician. Should you need any spare parts, please order genuine parts from your local Elation dealer. Please refer to the following points during routine inspections: A detailed electric check by an approved electrical engineer every 3 months, to make sure the circuit contacts are in good condition and prevent overheating, Be sure all screws and fasteners are securely tightened at all times, Lose screws may fall out during normal operation resulting in damage or injury, Check for any deformations on the housing, color lenses, rigging hardware and rigging points (ceiling, suspension, trussing). Deformations in the housing could a low for dust to enter into the fixture. Damaged rigging points or unsecured rigging could cause the fixture to fall and seriously injure a person(s). Inspect all moving parts and make sure there are no signs of wear and rotate/move without imbalances, Electric power supply cables must not show any damage, material fatigue or sediments. Never remove the ground prong from the power cable. 21 SIXPAR 300TM User Manual Ver. I

****** Page 22 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL FEATURES 50 Beam 250 Field Angles 5 Variable Dimming Curve Modes Dual Yoke / Floor Stand Multiple Unit Power Linking RDM – Remote Device Management Rugged Die-Cast Aluminum Exterior Flicker Free Operation for IV and FILM SOURCE (18) 12W 6-in-l RGBAW+UV LEDs 1 00, 000 Hour Average LED Life EFFECTS Electronic Strobe Color and Chase Macros Electronic Dimming: 0% – 100% 5 Variable Dimming Curve Modes CONTROL / CONNECTIONS (4) DMX Channel Modes (6 / 7 / 8/ 12) (4) Buffon Touch Control Panel LCD Menu Display 3pin & 5pin DMX and powerCON In/Out SIZE / WEIGHT Length: 12.3″ (313mm) Width: 4,9.” (125mm) Vertical Height: I I .8″ (300mm) Weight: 18,0 lbs. (8.1 kg) ELECTRICAL / THERMAL AC 10-250V – 50/60Hz 220W Max Power Consumption Power Linking: 5pcs @I IOV / I Opcs @240V 50F to 1 1 30F (-1 to 450C) APPROVALS / RATINGS elationlighting.com CE I IP20 c US Intertek Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice. 22 SIXPAR 300TM User Manual Ver. I

****** Page 23 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL PHOTOMETRIC DATA

elationlighting.com 150 250 Beam Field I 2m 0.64 0.88 lux 2, 1 70 2,490 2,930 823 510 8,500 (14.410) 3m 4m 9.8 5m Distance 1 50 Beam Diameter 250 Field Diameter RED LEDs GREEN LEDs BLUE LEDs WHITE LEDs AMBER LEDs UV LEDs FULL ON 16,4 0.4 0.45 lux 4,750 8,400 9,520 10,860 3,130 1,920 24,500 3.3 1.3 1.5 fc 441 780 884 1,009 291 178 2,276 6.6 2.1 2.9 fc 122 202 231 272 76 47 790 DIMENSIONAL DRAWINGS 365 mm 311 mm ooo O Coo oa DÖ ooo o QÖo• 125mm Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice. 23 SIXPAR 300TM User Manual Ver. I

****** Page 24 ****** E’L¯ÅiiÖF’ PPO”SS’ONAL ORDER CODE TRIGGER CLAMP SIXPAR300/GFH SIXPAR/BD300 LSF536 LSF537 LSF538 LSF559 EWDMXSYSTEM EWDMXT EWDMXR PLC3 PLC6 AC3PDMX5PRO AC5PDMX5PRO elationlighting.com ITEM Heavy Duly Wrap Around Hook Style Clamp Gel Frame and Holder Kit Barn Door (Gel Frame Holder Kit Required – Not Included) Light Shaping Filter 300 2011 x 2411 Sheet Light Shaping Filter 200 2011 x 2211 Sheet Light Shaping Filter 600 x 10 20″ x 24″ Sheet Light Shaping Filter 1 00 20″ x 24″ Sheet Wireless DMX System (l Transmitter, 1 Receiver) Wireless DMX Transmitter Receiver 3 (1 m) powerCON PRO Link Cable 6 (1 8m) powerCON PRO Link Cable 5 ft. (l .5m) 3pin PRO DMX Cable 5 ft. (l .5m) 5pin PRO DMX Cable Additional Cable Lengths Available SIXPAR 300TM User Manual Ver. I

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL



ELATION PROFESSIONAL SIXPAR 300 (01) PDF MANUAL

Leave a comment, question, review or page error below. Account not required.

This site uses Akismet to reduce spam. Learn how your comment data is processed.