Click here to download ELATION PROFESSIONAL CUEPIX BLINDER WW4 (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** E-CÅ+iÖD PROFESSIONAL CUEPIX BLINDER ww4TM User manual z

****** Page 2 ****** A TION elationlighting.com 02014 ELATION PROFESSIONAL all rights reserved, Information, specifications, diagrams, images, and instructions herein are subject to change without notice, ELATION PROFESSIONAL logo and identifying product names and numbers herein are trademarks of ELATION PROFESSIONAL. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted, Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-ELATION brands and product names are trademarks or registered trademarks of their respective companies. ELATION PROFESSIONAL and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and operation of this product. Elation Professional USA | 6122 S. Eastern Ave. I Los Angeles, CA, 90040 323-582-3322 | 323-832-9142 fax I elationlighting.com I info@elationlighting.com Elation Professional B.V. I Junostraat 2 | 6468 EW Kerkrade, Netherlands +31 45 546 85 66 | +31 45 546 85 96 fax I elationlighting.eu I info@elationlighting.eu DOCUMENT VERSION Please check elationlighting.com for the latest revision/update of this manual. Document Date Version 11/2014 DMX Software Version .05 Channel Modes 1/2/4/ 5/7/9 2 Notes Initial release, CUEPIX BLINDER WW4TM User Manual Ver. I

****** Page 3 ****** A TION CONTENTS General Information Warranty Safety Instructions General Guidelines Fixture Overview Fixture Installation Understanding DMX Fixture Menu DMX Channel Functions And Values Cleaning and Maintenance Technical Specifications Optional Accessories 3 elation lighting 4 6 7 8 9 10 13 22 23 24 26 com CUEPIX BLINDER WW4TM User Manual Ver. I

****** Page 4 ****** A TION elationlighting.com INTRODUCTION Congratulations, you have just purchased one of the most innovative and reliable lighting fixtures on the market today! The CUEPIX BLINDER WW4TM has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit. These instructions contain important information regarding safety during use and maintenance. UNPACKING Thank you for purchasing the CUEPIX BLINDER WW4TM by Elation Professional@ Every CUEPIX BLINDER WW4TM has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping, If the carton appears to be damaged, carefully inspect your unit for damage and be sure all accessories necessary to operate the unit have arrived intact. In the event damage has been found or parts are missing, please contact our customer support team for further instructions. Please do not return this unit to your dealer without first contacting customer support at the number listed below. Please do not discard the shipping carton in the trash. Please recycle whenever possible. BOX CONTENTS (l) powerCON Cable Manual & Warranty Card 4 CUEPIX BLINDER WW4TM User Manual Ver. I

****** Page 5 ****** A TION CUSTOMER SUPPORT elationlighting.com Elation Professional@ provides a customer support line, to provide set up help and to answer any question should you encounter problems during your set up or initial operation, You may also visit us on the web at elationlighting.com for any comments or suggestions, For service related issue please contact Elation Professional@ ELATION SERVICE USA – Monday – Friday 8:OOam to 5:OOpm PST Voice: 323-582-3322 Fax: 323-832-9142 E-mail: support@elationlighting.com ELATION SERVICE EUROPE – Monday – Friday 08:30 to 1 7:00 CET Voice: +31 45 546 85 30 Fax: +31 45 546 85 96 E-mail: support@elationlighting.eu WARRANTY REGISTRATION The CUEPIX BLINDER WW4TM carries a two-year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A,) number, The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A. number must also be written down on a piece of paper and included in the shipping container. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. Items returned without a R.A. number clearly marked on the outside of the package will be refused and returned at customer’s expense. You may obtain a R.A. number by contacting customer support, IMPORTANT NOTICE! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself; doing so will void your manufactures warranty. Damages resulting from modifications to this fixture and/or the disregard of safety and general user instructions found in this user manual void the manufactures warranty and are not subject to any warranty claims and/or repairs. 5 CUEPIX BLINDER WW4TM User Manual Ver. I

****** Page 6 ****** A TION elation lighting com A, Elation Professional@ hereby warrants, to the original purchaser, Elation Professional@ products to be free of manufacturing defects in material and workmanship for a period of two years, (730 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories, It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought, Bi For warranty service, send the product only to the Elation Professional@ factory, All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, Elation Professional@ will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in its original package No accessories should be shipped with the producti If any accessories are shipped with the product, Elation Professional@ shall have no liability what so ever for loss of or damage to any such accessories, nor for the safe return thereof, C, This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which Elation Professional@ concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the Elation Professional@ factory unless prior written authorization was issued to purchaser by Elation Professional@; if the product is damaged because not properly maintained as set forth in the instruction manual, D. This is not a service contract, and this warranty does not include maintenance, cleaning or periodic check-up, During the period specified above, Elation Professional@ will replace defective parts at its expense, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship, The sole responsibility of Elation Professional@ under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of Elation Professional@. All products covered by this warranty were manufactured after January 1, 1990, and bare identifying marks to that effect. E, Elation Professional@ reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured, F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by Elation Professional@ in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall Elation Professional@ be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product, G, This warranty is the only written warranty applicable to Elation Professional@ Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published, 6 CUEPIX BLINDER WW4TM User Manual Ver. I

****** Page 7 ****** A TION SAFETY elation lighting com INSTRUCTIONS The CUEPIX BLINDER WW4TM is an extremely sophisticated piece of electronic equipment. To guarantee a smooth operation, it is important to follow the guidelines in this manual, The manufacturer of this device will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. This device falls under PROTECTION CLASS 1. It’s essential this device be grounded properly. Only qualified personnel should perform all electrical connections, KEEP THIS FIXTURE AWAY FROM RAIN AND MOISTURE! UNPLUG POWER BEFORE SERVICING FIXTURE NEVER TOUCH FIXTURE DURING OPERATION AS IT MAY BE HOT NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE SENSITIVE PERSONS MAY SUFFER AN EPILETIC SHOCK For proper operation, follow the Installation guidelines described in this manual, Only qualified and certified personnel should perform installation of this fixture and only the original rigging parts (brackets) included with this fixture should be used for installation, Any modifications will void the original manufactures warranty and increase the risk of damage and/or personal injury, Never look directly into the light source of this fixture to prevent risk of injury to your retina, which may induce blindness, Those suffering from EPILEPSY should avoid looking directly into the light source of this unit at all times. The fan and air inlets must remain clean and never blocked. Allow approx. 6″ (15cm) between this fixture and other devices or a wall for proper cooling Always disconnect from main power source before performing any type of service and/or cleaning procedure, Only handle the power cord by the plug end, never pull out the plug by tugging the wire portion of the cord, Do not operate this fixture if the power cord has become frayed, crimped and/or damaged, If the power cord is damaged, replace it immediately with a new one of similar power rating. 7 CUEPIX BLINDER WW4TM User Manual Ver. I

****** Page 8 ****** A TION elationlighting.com NEVER OPEN THIS FIXTURE WHILE IN USE! During the initial operation of this fixture, a light smoke or smell may emit from the interior of the fixture, This is a normal process and is caused by excess paint in the interior of the casing burning off from the heat associated with the lamp and will decrease gradually over time, This fixture is a professional lighting effect designed for INDOOR / DRY LOCATIONS ONLY on stage, in nightclubs, theatres, etc. Please make sure there are NO FLAMMABLE MATERIALS close to the fixture while operating, to prevent any fire hazard. The fixture must be installed in a location with adequate ventilation, at least 1.5 feet ( 15m) from adjacent surfaces, Be sure no air ventilation slots are blocked, DO NOT attempt installation and/or operation without knowledge how to do so. DO NOT permit operation by persons who are not qualified to operate this type of fixture. Most damages are the result of operations by nonprofessionals, Consistent operational breaks may ensure the fixture will function properly for many years to come. DO NOT shake fixture, avoid brute force when installing and/or operating fixture, Always install the fixture with an appropriate safety cable. When installing the fixture in a suspended environment, always use mounting hardware that is no less than MIO x 25 mm, also be sure the hardware is insert in the pre-arranged screw holes in the bracket of the fixture, Use the original packaging and materials to transport the fixture in for service. DO NOT TOUCH the housing bare-hand during its operation, Turn OFF the power and allow approximately 15 minutes for the fixture to cool down before replacing or serving. 8 CUEPIX BLINDER WW4TM User Manual Ver. I

****** Page 9 ****** A TION elationlighting.com 6 7 g 9 10 13 14 15 1. 2. 3. 4. 5. 6. 7. 8. 9. LCD Menu Control Display MODE/ESC Button UP Button DOWN Button ENTER Button Fuse powerCON IN 3pin DMX IN 5pin DMX IN 1 2345 9 10.RJ45 NET IN 11.RJ45 NET OUT 12.3pin DMX OUT 13.5pin DMX OUT 14.powerCON OUT 15. Safety Cable Rigging Point CUEPIX BLINDER WW4TM User Manual Ver. I

****** Page 10 ****** A TION FIXTURE elationlighting.com INSTALLATION Keep fixture at least 5.0 ft (1 -5m) away from any flammable materials, decorations, pyrotechnics, etc. A qualified electrician should be used for all electrical connections and/or installations. CAUTIONS For added protection, mount the fixture in areas outside walking paths, seating areas, or in areas were unauthorized personnel might reach the fixture. Ambient operating temperature range for this fixture is 50Fto 1130F (-150C to 450C). Do not use the fixture under or above this temperature, Before mounting the fixture to any surface, make sure the installation area can hold a minimum point load of 10 times the weight of the fixture, (210 lbs / 95 kg) Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety cable, Never stand directly below the device when mounting, removing or servicing. POWER LINKING Max number of units that can be power linked is 1 units @1 IOV and 4 units @220V CLAMP MOUNTING The CUEPIX BLINDER WW4TM provides an integrated yoke/rigging bracket, When mounting this fixture to truss be sure to secure an appropriately rated clamps to the yoke/rigging bracket using a MIO screw fitted through the center hole. 10 CUEPIX BLINDER WW4TM User Manual Ver, I

****** Page 11 ****** A TION MOUNTING POINTS elationlighting.com Overhead mounting requires extensive experience, including amongst others calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the device. If you lack these qualifications, do not attempt the installation yourself, Improper installation can result in bodily injury, Fixture is fully operational in the specific mounting positions as illustrated below, .1 r SAFETY CABLE Always use a Safety Cable whenever installing this fixture in a suspended environment to ensure the fixture will not drop if the clamp fails. CUEPIX BLINDER WW4TM User Manual Ver, I

****** Page 12 ****** A TION SECURING elation lighting com Regardless of the rigging option you choose for your CUEPIX BLINDER WW4TM always be sure to secure your fixture with a safety cable, The fixture provides a built-in rigging point for a safety cable on the base of the unit as illustrated below. Be sure to only use this designated rigging point to attach the safety cable, SAFETY CABLE RIGGING POINT 0000 CUEPIX BLINDER o 12 CUEPIX BLINDER WW4TM User Manual Ver, I

****** Page 13 ****** A TION elationlighting.com UNDERSTANDING DMX DMX-512 DMX is short for Digital Multiplex, This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers, DMX allows all makes and models of different manufactures to be linked together and operate from a single controller. This is possible as long as all the fixtures and the controller are DMX compliant, A DMX controller sends the DMX data instructions to the fixture allowing the user to control the different aspects of an intelligent light. DMX data is sent out as serial data that travels from fixture to fixture via data “IN” and data “OUT” XLR terminals located on the fixtures (most controllers will only have output jacks), DMX LINKING To ensure proper DMX data transmission, always use proper DMX cables and a terminator. When using several DMX fixtures try to use the shortest cable path possible. Never split a DMX line with a “Y” style connector. The order in which the fixtures are connected in a DMX line does not influence the DMX addressing, For example; a fixture assigned a starting DMX address of 1 may be placed anywhere in the DMX chain, at the beginning, at the end, or anywhere in the middle. The DMX controller knows to send data assigned to address 1 to that fixture no matter where it is located in the DMX chain. The CUEPIX BLINDER WW4TM can be controlled via DMX-512 protocol and the DMX address is set via the control menu. DATA CABLE (DMX Cable) REQUIREMENTS (For DMX and Master/Slave Operation) Your fixture and your DMX controller require a standard 3pin or 5pin XLR connector for data input and data output (see figure below). If you are making your own cables, be sure to use two conductor, shielded digital DMX cable rated at 1 20 ohms; this cable is designed for DMX transmission and may be purchased from your Elation dealer or at most professional lighting retailers. Your cables should be made with a male and female XLR connector on either end of the cable, Also, remember that a DMX line must be daisy chained and cannot be split, unless using an approved DMX splitter such as Elation’s Opto Branch ATM, Opto Branch 8TM, or DMX-Branch/4TM. 13 CUEPIX BLINDER WW4TM User Manual Ver, I

****** Page 14 ****** A TION DMX Output 3-Pin XLR Socket elationlighting DMX Input 3-Pin XLR Socket DMX Output 5-Pin XLR Socket DMX Input 5-Pin XLR Socket com 1 : Ground 2: Data (-) 3: Data (+) 4: Open 5: Open Be sure to follow the above figure when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR outer casing. Grounding the shield could cause a short circuit and erratic behavior. DMX-512 CONTROLLER CONNECTION Connect the provided XLR cable to the female XLR output of your controller and the other side to the male XLR input of the CUEPIX BLINDER WW4TM The diagram below illustrates a typical DMX-512 connection when the fixture is in the 9 Channel Mode, You can chain multiple panels together through serial linking. The cable that should be used is two conductor, shielded DMX cable with XLR input and output connectors, Always be sure daisy chain your in and out data connections, never split or “Y” your DMX connections unless you are using an approved DMX splitter such as Elation’s Opto Branch 4TM, Opto Branch 8TM, or DMX-Branch/4TM DMX CONTROLLER Address 1 Address 10 14 Address 19 CUEPIX BLINDER WW4TM User Manual Ver, I

****** Page 15 ****** A TION elationlighting.com DMX-512 CONNECTION WITH DMX TERMINATOR A DMX terminator should be used in all DMX lines especially in longer runs. The use of a terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line, Using a line terminator will decrease the possibilities of erratic behavior, 1200 spin XLR DMX CONNECTORS Termination reduces signal errors and avoids signal transmission problems and interference. It is always advisable to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3 (DMX +) of the last fixture. Some manufactures use 5pin XLR connectors for DATA transmission in place of 3pin, 5pin XLR fixtures may be implemented in a 3pin XLR DMX line. When inserting standard 5pin XLR connectors in to a 3pin line a cable adaptor must be used, these adaptors are readily available at most electric stores, The following chart details a proper cable conversion. 3-Pin XLR to 5-Pin XLR Conversion Conductor Ground/Shield Data Compliment (- signal) Data True (+ signal) Not Used Not Used 3-Pin XLR Female (Out) 5-Pin XLR Male (In) Pin 1 Pin 2 Pin 3 15 Pin I Pin 2 Pin 3 Pin 4 – Do Not Use Pin 5 – Do Not Use CUEPIX BLINDER WW4TM User Manual Ver, I

****** Page 16 ****** A TION DMX ADDRESSING elationlighting.com All fixtures should be given a DMX starting address when using a DMX controller, so the correct fixture responds to the correct control signal. This digital starting address is the channel number from which the fixture starts to “listen” to the digital control information sent out from the DMX controller. The allocation of this starting DMX address is achieved by setting the correct DMX address on the digital display located on the back of the fixture, You can set the same starting address for all fixtures or a group of fixtures, or set different address for each individual fixture. Be advised that setting all fixtures to the same DMX address will subsequently control all fixtures in the same fashion, in other words, changing the settings of one channel will affect all the fixtures simultaneously, If you set each fixture to a different DMX address, each unit will start to “listen” to the channel number you have set, based on the quantity of control channels (DMX channels) of each fixture, That means changing the settings of one channel will only affect the selected fixture. In the case of the CUEPIX BLINDER WW4TM, when in the 9 Channel Mode you should set the starting DMX address of the first unit to l, the second unit to 10 (l + 9), the third unit to 19 (10 + 9), and so on, Note: During start-up the CUEPIX BLINDER WW4TM will automatically detect whether a DMX data signal is being received or not, If the fixture is not receiving a DMX signal please check the following: The 3pin or 5pin XLR input plug (cable with DMX signal from controller) is not connected or is not inserted completely into the DMX input jack of the fixture, The DMX controller is switched off or defective. The DMX cable or connector is defective. A DMX terminator has been inserted into the last fixture in your DMX chain, 16 CUEPIX BLINDER WW4TM User Manual Ver, I

****** Page 17 ****** A TION ON-BOARD SYSTEM MENU elationlighting.com The CUEPIX BLINDER WW4TM comes with an easy to navigate system menu. next section will detail the functions of each command in the system menu, LCD MENU CONTROL PANEL The control panel (see image below) located on the top of the fixture allows you to access the main menu and make all necessary adjustments to the CUEPIX BLINDER WW4TM. During normal operation, pressing MODE button once will access the fixture’s main menu. Once in the main menu you can navigate through the different functions and access the sub-menus with the UP, and DOWN buttons. Once you reach a field that requires adjusting, press the ENTER button to activate that field and use the UP and DOWN buttons to adjust the field, Pressing the ENTER button once more will confirm your setting, You may exit the main menu at any time without making any adjustments by pressing the MODE button. NOTE: the LCD Menu Control Display will shut OFF and lockout after 30 seconds of no use. Press and hold the MODE button for 10 seconds to unlock the LCD display. DMX MODE ADDR:ØOI r.H: 0000 MODE DOWN tNttR INFORMATION DISPLAYED DURING INITIAL POWER ON When the fixture is initially powered ON, the display shows the following information: Software Update Please Wait… ELATION CUEPIX BLINDER aww VI .05 Fixture Software Version (Greater than or equal to) CUEPIX BLINDER WW4TM User Manual Ver, I

****** Page 18 ****** A TION MENU OPTIONS / VALUES DMX MODE ADDR:OOI -512 ADDR:xxx , 02, 04, 05, 07, 09 CH:xx SLAVE MODE AUTO RUN FQN:OI -99 FQN:xx , STATIC 01 -09 09.FLOW4 Standard, Stage, N, Architectural, Dim Curve Pixel Flip NO DMX MODE Ethernet Set Fixture ID Fixture ID Device IP Addr Fixture ID Ctrl Addr Fixture ID Universe Ethernet Set Protocol Set Ethernet Set Network Switch elationlighting ELATIONO CUEPIX BLINDER SYSTEM MENU Specifications are subject to change without any prior written notice com Theatre STANDARD, FLIP l, FLIP 2, FLIP 3, Hold, Blackout, Program Service PIN Password 050 ooo,ooo.ooo.ooo 000-255 Kling-Net, ArtNet ON, OFF FLIP 4 18 DESCRIPTION Set DMX Address, Set DMX Channel Mode. Set unit to Slave Mode, Set the number of times each internal macro will repeat before moving to the next macro, Select Internal Program Macro. See INTERNAL MACRO MENU. Set desired Dimming Curve, Set starting Pixel (COB module), See Pixel Flip Section. Define how fixture reacts when NO DMX signal present, Enter Service Password to access Ethernet Menus. Set IP address. (Need to enter Service PIN to access this menu) Set Subnet Mask, (Need to enter Service PIN to access this menu) Set DMX Universe number, (Need to enter Service PIN to access this menu) Set Protocoli Set Network switch. CUEPIX BLINDER WW4TM User Manual Ver, I

****** Page 19 ****** A TION MACRO 01 STATIC 02DREAM 03,METEOR oatFADE 05,CHANGE 06,FLOW I 07 FLOW 2 08,FLOW 3 09,FLOW 4 elation lighting ELATIONO CUEPIX BLINDER INTERNAL MACRO MENU Specifications are subject to change without any prior written notice. com OPTIONS / VALUES WI 000-255 W2:ooo-255 W3:ooo-255 W4:ooo-255 SpeedOO-99 SpeedOO-99 SpeedOO-99 SpeedOO-99 SpeedOO-99 SpeedOO-99 SpeedOO-99 SpeedOO-99 FlashOO-99 FlashOO-99 FlashOO-99 FlashOO-99 FlashOO-99 FlashOO-99 FlashOO-99 FlashOO-99 FlashOO-99 FlashOO-99 FlashOO-99 FlashOO-99 19 DESCRIPTION Seven Color Dreaming Speed & Flash Adjustable Dreaming Speed & Flash Adjustable Flow Speed & Flash Adjustable Fade Speed & Flash Adjustable Change Speed & Flash Adjustable Chase Speed & Flash Adjustable Chase Speed & Flash Adjustable Chase Speed & Flash Adjustable Chase Speed & Flash Adjustable CUEPIX BLINDER WW4TM User Manual Ver, I

****** Page 20 ****** A TION FLIP SETTING elationlighting.com Select the desired starting COB module and chase direction from one of the following modes below via UP/DOWN buttons and then press ENTER to confirm. STANDARD FLIP 2 FLIP 4 20 FLIP 1 FLIP 3 CUEPIX BLINDER WW4TM User Manual Ver, I

****** Page 21 ****** A TION DIMMING CURVES elationlighting.com The DimCurve menu allows you to select one of the following preset dimming curves: Standard, Stage, TV, Architectural, Theatre, or Default. Select the desired mode via UP/DOWN buttons and then press ENTER to confirm. (See diagram below for more details) 55 Ramp Effect Standard Stage Architectural Theatre Dimmer 100% 780 1180 1380 1580 5 OS (Fade Time) 1100 1520 1730 1940 Trv.g 1540 1860 2040 2230 IS (Fade Time) 1660 lg40 2120 2280 DMX WORKSHOPTM (alternative software option to configure network settings) DMX-WorkshopTM is a fully featured network management, analysis, configuration and diagnostics tool for Art-Net networks, It can be used to configure the Ethernet network settings on this fixture remotely such as the IP Address, Subnet Mask, and the DMX Universe, This software application is Windows XPTM and Windows 7TM compatible and is free of charge and available via download here. (See link below) affsficlicence.com/index.php?mode=products&sub=ovetview&action=&product id=351 21 CUEPIX BLINDER WW4TM User Manual Ver, I

****** Page 22 ****** FUNCTION 1 CH A TION MODE 2 3 2 elationlighting.com ELATIONO CUEPIX BLINDER WW4TM DMX Channel Values / Functions (9 DMX Channels) Specifications are subject to change without any prior written notice. *Control of (4) COB Modules chase direction depends on the Flip setting. CHANNEL 2 3 5 VALUE 7 CH 9 CH 2 3 5 6 0-255 0-255 2 0-255 3 0-255 0-255 5 6 8 9 0-20 21-42 65-81 88-1 111-123 124-146 147-169 70-192 193-255 0-255 0-255 0-31 32-63 64-95 96-12/ 128-159 160-191 192-223 224-255 0-20 21-40 41-60 61-80 81-100 101 -255 ALL (4) C Intensily O to 100% *COB MODULE DIMMER Intensily O to 100% *COB #2 MODULE DIMMER Intensily O to 100% *COB #3 MODULE DIMMER Intensily O to 000/0 *COB MODULE DIMMER Intensily O to 100% INTERNAL MACROS Normal DREAM METEOR FADE CHANGE FLOW I FLOW 2 FLOW 3 FLOW 4 NO Function MACRO SPEED MACRO Program Speed SLOW to FAST MASTER DIMMER Intensily O to 100% FLASH / STROBE COB OFF COB ON FLASH Strobe Effect SLOW to FAST COB ON PULSE Strobe Effect SLOW to FAST COB ON RANDOM Strobe SLOW to FAST COB ON DIMMING CURVE MODES STANDARD STAGE ARCHITECTURAL THEATRE Default to Unit Setting 22 CUEPIX BLINDER WW4TM User Manual Ver, I

****** Page 23 ****** A TION CLEANING c elationlighting.com O Disconnect power before cleaning or maintenance. Frequent cleaning is recommended to insure proper function, optimized light output, and an extended life, The frequency of cleaning depends on the environment in which the fixture operates: damp, smoky or particularly dirty environments can cause greater accumulation of dirt on the fixture’s optics. Clean the external lens surface at least every 20 days with a soft cloth to avoid dirt/debris accumulation, • Never use alcohol, solvents, or ammonia based cleaners. MAINTENANCE Regular inspections are recommended to insure proper function and extended life, There are no user serviceable parts inside this fixture, please refer all other service issues to an authorized Elation service technician. Should you need any spare parts, please order genuine parts from your local Elation dealer. Please refer to the following points during routine inspections: A detailed electric check by an approved electrical engineer every three months, to make sure the circuit contacts are in good condition and prevent overheating. Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall, Check for any deformations on the housing, color lenses, rigging hardware and rigging points (ceiling, suspension, trussing), Deformations in the housing could allow for dust to enter into the fixture. Damaged rigging points or unsecured rigging could cause the fixture to fall and seriously injure a person(s), Electric power supply cables must not show any damage, material fatigue or sediments. Never remove the ground prong from the power cable. 23 CUEPIX BLINDER WW4TM User Manual Ver, I

****** Page 24 ****** A TION FEATURES High Power Long Life Warm White COB LEDs 620 Beam Angle – 1 000 Field Angle Individual Control of Each COB Module 5 Variable Dimming Curve Modes RDM (Remote Device Management) Flicker FREE Operation for B/ and FILM SOURCE (4) OOW Warm White COB LEDs 100.000 Hour Average Life EFFECTS Strobe Variable and Selectable Dimming Curves CONTROL / CONNECTIONS 6 DMX Channel Modes (l /2/4/5/7 / 9) 4 Button Control Panel and LCD Menu Display ArtNet + KlingNET Protocol Support RDM (Remote Device Management) (2) RJ45 Ports 3pin and 5pin DMX In/Out RDM (Remote Device Management) powerCON Power In/Out SIZE / WEIGHT Length: 1 57″ (400 mm) Width: 6.9″ (1 74 mm) Horizontal Height: 17.4″ (441 mm) Weight: 21 .O lbs. (9,5 kg) ELECTRICAL / THERMAL AC 100-240V – 50/60Hz 427W Max Power Consumption Power Linking: I pcs OV / 4pcs @220V 50F to (-1 to 450C) APPROVALS / RATINGS CE I IP20 elationlighting com Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice. 24 CUEPIX BLINDER WW4TM User Manual Ver, I

****** Page 25 ****** A TION PHOTOMETRIC DATA Distance 62′ Beam Diameter Field Dameter 2.38 Photometrics lux elation lighting 9.8 com Beam 16.4 100′ Field I 2m 3.3 lux 4m 13.1 fc 5m lux lux lux ALL FULL ON 12,300 1 ‘143 DIMENSIONAL DRAWINGS 4 mm 37 Omn Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice. 25 CUEPIX BLINDER WW4TM User Manual Ver, I

****** Page 26 ****** A TION ORDER CODE TRIGGER CLAMP EWDMXSYSTEM EWDMXT EWDMXR PLC3 PLC6 AC3PDMX5PRO AC5PDMX5PRO elationlighting.com ITEM Heavy Duly Wrap Around Hook Style Clamp Wireless DMX System (1 Transmitter, 1 Receiver) Wireless DMX Transmitter Wireless DMX Receiver 3 (l m) powerCON PRO Link Cable 6 (1 18m) powerCON PRO Link Cable 5 ft. (l .5m) 3pin PRO DMX Cable 5 ft. (l .5m) 5Pin PRO DMX Cable Additional Cable Lengths Available 26 CUEPIX BLINDER WW4TM User Manual Ver, I

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL



ELATION PROFESSIONAL CUEPIX BLINDER WW4 (01) PDF MANUAL

Leave a comment, question, review or page error below. Account not required.

This site uses Akismet to reduce spam. Learn how your comment data is processed.