ECOPLUS ECO 7400 (01) PDF MANUAL

EcoPlus Submersible pumps are designed for both fresh and salt water.

Yes, the unit can be used both inside and outside of water.

These pumps are suitable for use in ponds, aquariums, fountains and in combination with filtration systems. Due to their high flow rate and total head, they can be used in settings ranging from large waterfalls to filtration systems.

The vortex impeller and ceramic components allow this unit to be both energy saving and efficient. The unique design of the impeller allows for a dramatic reduction in the frequency of cleaning.

Use with a 120 volt power source.

Yes, the pump is provided with a thermal protector that temporarily switches off the pump in case of overheating and the pump may automatically restart.

The pump has a thermally protected enclosure type 3 for indoor and outdoor use.

This pump has been evaluated for use with water only.

The EcoPlus Submersible pumps do not require lubrication or special maintenance beyond regular cleaning.

Make sure that the voltage and frequency of power supply comply with the specifications on the product. Check that the supply is rated and is correctly fused.

The pump is only suitable with a Fl-switch 30mA and has to be connected to a regular safety plug socket.

Never pull the pump or remove the pump by pulling the cord. Never remove the plug or shorten the cord.

The electricity cable cannot be replaced. If the cable becomes damaged, the pump should be discarded. Do not use this product if the electricity supply cable becomes damaged.

Install only on a circuit protected by a Ground-Fault Circuit-Interrupter (GFCI). This pump is supplied with a grounding conductor grounding-type attachment plug. To reduce the risk of electric shock, be certain that it is connected only to a properly grounded, grounding-type receptacle. For proper installation, see the instruction manual.

The electricity supply cord to the pump should extend below the 13-amp plug socket; this is to prevent water drops from making contact with the plug or electricity supply outlet.

We recommend the use of a ground fault circuit breaker <30mA with this pump and any other electrical products used in or around the aquarium or hydroponic system.

If the 13-amp supply plug gets wet DO NOT TOUCH THE PLUG. Turn off the electrical supply at the circuit breaker before removing the plug.

To avoid the possibility of the appliance plug or outlet getting wet, position the aquarium stand and tank to one side of a wall-mounted outlet to prevent water from dripping onto the outlet or plug. A “drip loop” should be arranged by the user for each cord connecting an aquarium appliance to an outlet. The “drip loop” is the part of the cord below the level of the outlet, or the connector if an extension cord is used, to prevent water traveling along the cord and coming in contact with the outlet.

If the plug or outlet does get wet, DON’T unplug the cord. Disconnect the fuse or circuit breaker that supplies power to the appliance. Then, unplug and examine for presence of water in the outlet.

The pump is not suitable for use in swimming pools, swimming ponds, or other situations where humans may make bodily contact with the water. This pump has not been investigated for use in swimming pool or marine areas.

Always turn the unit off before cleaning or removing the pump for maintenance.

To reduce the risk of electric shock, use only on portable self-contained fountains no larger than 5 feet in any dimension.

To avoid injury, do not contact moving parts or hot parts such as heater, reflectors, lamp bulbs, and the like.

Always unplug an appliance from an outlet when not in use, before putting on or taking off parts, and before cleaning. Never yank cord to pull plug from outlet. Grasp the plug and pull to disconnect.

Do not use an appliance for other than intended use. The use of attachments not recommended or sold by the appliance manufacturer may cause unsafe conditions.

Do not install or store the appliance where it will be exposed to the weather or temperatures below freezing. Also, do not use or leave the pump in freezing conditions.

Make sure appliance mounted on a tank is securely installed before operating it.

If an extension cord is necessary, a cord with a proper rating should be used. A cord rated for less than 120 volts may overheat. Care should be taken to arrange the cord so that it will not be tripped over or pulled.

No, do not connect your pump to the electricity supply while the unit is out of water.

Never let the pump run dry as this will damage the impeller and may also overheat the pump and burn out the electric coil. Never let the pump run dry.

If you intend to drain the aquarium or change some of the water you must disconnect the pump before starting work to allow the unit to cool down.

Always disconnect any electrical items from the electricity supply before working in your aquarium or hydroponic system.

Never let the water level in the aquarium fall below the top of the pump body.

Do not use this product if the body becomes damaged or cracked.

If the appliance shows any sign of abnormal water leakage, immediately unplug it from the power source. (Submersible equipment only)

Carefully examine the appliance after installation. It should not be plugged in if there is water on parts not intended to be wet.

Do not operate any appliance if it has a damaged cord or plug, or if it is malfunctioning or has been dropped or damaged in any manner. For such situations, do not attempt repairs by yourself; return the appliance to an authorized service facility for service or discard the appliance.

Yes, close supervision is necessary when any appliance is used by or near children.

Place the pump in the aquarium or hydroponic system attaching the unit to the side of the tank, using the sliding bracket (with the four suckers) provided with the unit.

Yes, the unit should be fully submersible in the water, as the water cools the pump. If used under water, the pump should be submerged no less than 6 inches below the water level.

Hang the attached airline with its filter outside the aquarium or hydroponic system in a position where it can draw clean air from outside the aquarium or tank to support air bleed.

Place the pump in an area of the aquarium or hydroponic system where the water can be circulated around in a circular motion.

If the pump is powering an under-gravel filter, make sure that the gravel is clean to ensure a good flow rate.

When reattaching the rotor to the pump body after cleaning, make sure the 2 holes on the impeller base and the 2 dowels on the pump body fit together for proper assembly. The hole and the dowel should be fit together.

Ensure that the pump unit is cleaned regularly. Clean the impeller at least every month.

The impeller is situated in the pump housing and can be accessed by holding the pump body and rotating the impeller cover and pulling the pump cover away from the main body.

When disassembling the impeller, please ensure that you do not lose the small plastic washers positioned at the top and bottom of the impeller, as these ensure the quiet and efficient operation of the pump.

Clean the impeller in fresh water, and the housing with cotton swabs or similar to remove all the accumulated debris from the pump and reassemble.

1. Turn off the power supply, move the pump to a dry location.

2. Loosen the screws from the impeller cover; remove the impeller cover from the pump body by lightly shaking the unit.

3. Pull the rotor assembly away from the pump body.

4. Wash parts with fresh water carefully.

5. Reattach the rotor to the pump body carefully after cleaning; make sure the 2 holes on the impeller base and the 2 dowels on the pump body fit together for proper assembly.

6. Turn the rotor by hand, the rotor should move freely.

7. Check the “O” ring of the pump body.

8. Replace the impeller cover on the pump body and tighten the stainless steel screws.

If the unit is used outside water, it should be no less than 6 inches lower than the surface of the water.

The water output from the pump usually slows down, indicating that the impeller needs cleaning.

The pump air bleed will stop working if the water flow from the pump is reduced. This may be caused by the gravel in the bed of the under-gravel filter becoming so dirty that it reduces flow to the pump.

If the pump becomes noisy, replace the impeller, as this component is a wearable part.

If your power head is not pumping water out, turn off the power and investigate the reason for the problem. Possible causes are dirty filter medium, broken impeller, dirty impeller, dirty impeller housing or the fuse in the plug may have blown.