ECHO POWER PRUNER PPT-266 (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD ECHO POWER PRUNER PPT-266 (01) PDF MANUAL


PDF Content Summary: Power PrunerTM Operator's Manual MODEL: PPT-266 PPT-266H PPT-266S WARNING Users of this equipment risk injury to themselves and others if the unit is used improp erly and/or safety precautions are not followed. ECHO provides an operator’s manual and a safety manual. Both must be read and understood for proper and safe operation. Failure to do so could result in serious injury.

X7702096004 X770001574 03/13

2 Introduction Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the job-dependability. Read and understand this manual and the SAFETY MANUAL. You will find both easy to use and full of helpful operations tips and SAFETY messages. the operator's manual Keep it in a safe place for future reference. Contains speci fications and information for safety, operation, maintenance, storage, and assembly specific to this product. the safety manual Keep it in a safe place for future reference. Explains pos sible hazards and the measures you should take to insure safe operation.

Table of Contents Introduction..........................................................................2 - The Operator's Manual .................................................2 - The Safety Manual.......................................................2 Safety ...................................................................................3 - Manual Safety Symbols and Important Information ..................................................................3 - International Symbols..................................................3 - Personal Condition and Safety Equipment ..................4 - Kickback ......................................................................6 - Equipment....................................................................7 Emission Control .................................................................8 Description...........................................................................8 Contents.............................................................................12 Assembly............................................................................12 - Handle Shaft/Drive Shaft (PPT-265) .........................12 - Handle Shaft/Power Head..........................................13 - Throttle Linkage and Ignition Leads..........................14 - Cutting Attachment to Drive Shaft Installation .........15 - Saw Chain Tension Adjustment .................................16 Operation............................................................................17 - Fuel ............................................................................17 - Lubricating the Guide Bar and Saw Chain ................19 - Adjusting Automatic Oiler.........................................19 - Starting Cold Engine..................................................20 - Starting Warm Engine................................................21 - Stopping Engine.........................................................22 - Pruning Techniques....................................................22 Copyright© 2013 By Echo, Incorporated All Rights Reserved. Maintenance.......................................................................23 - Skill Levels................................................................23 - Maintenance Intervals................................................23 - Air Filter.....................................................................24 - Fuel Filter...................................................................24 - Spark Plug..................................................................25 - Cooling System Cleaning ..........................................25 - Exhaust System..........................................................26 - Carburetor Adjustment...............................................28 - High Altitude Operation ..........................................28 - Lubrication.....................................................................29 - Guide Bar and Saw Chain Replacement........................30 - Filing Saw Chain........................................................33 Troubleshooting .................................................................34 Storage ...............................................................................35 Specifications.....................................................................36 Warranty Statements..........................................................37 Servicing Information ........................................................40 - Parts............................................................................40 - Service........................................................................40 - ECHO Consumer Product Support............................40 - Warranty Card............................................................40 - Additional or Replacement Manuals .........................40 Specifications, descriptions and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice. Illustrations may include optional equipment and accessories, and may not include all standard equipment.

Power PrunerTM Operator's Manual 3 Safety Manual Safety Symbols and Important Information Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages pre ceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you.

DANGER The safety alert symbol accompanied by the word “DANGER” calls attention to an act or condition which WILL lead to serious personal injury or death if not avoided. WARNING Circle and slash symbol This symbol means the specific action shown is prohibited. Ignoring these prohi bitions can result in serious or fatal injury. NOTE The safety alert symbol accompanied by the word “WARNING” calls attention to an act or condi tion which CAN lead to serious personal injury or death if not avoided. CAUTION The safety alert symbol accompanied by the word “CAUTION” calls attention to an act or condition which may lead to minor or moderate personal injury if not avoided. international symbols Symbol description/application Symbol form/shape Symbol Symbol form/shape description/application This enclosed message provides tips for use, care and maintenance of the unit. IMPORTANT The enclosed message provides information neces sary for the protection of the unit. Symbol description/application Symbol form/shape Symbol Symbol form/shape description/application

Read and understand Operator's Manual. Wear eyes, ears and head protection Fuel and oil mixture Finger Severing Wear hand DO NOT allow flames or sparks near fuel. Emergency stop Wear slip resistant foot wear. Ignition ON/OFF

Hot Surface Safety/Alert protection. Use two handed. DO NOT smoke Chain lubrication Primer bulb Carburetor adjustment

Avoid all power lines. This unit is not insu lated against electri cal current. Keep bystanders at least 15 meters (50 feet) away. near fuel. Do not operate closer than 15 M (50 ft.) from electrical haz ards. Plan retreat path from falling objects. Carburetor adjustment - Low speed mixture Carburetor adjustment - Idle speed Choke Control "Cold Start" Position (Choke Closed) - High speed mixture Choke Control "Run" Position (Choke Open)

4 personal condition AND safety equipment WARNING Users of this product risk injury to themselves and others if the unit is used improperly and/or safety precautions are not followed. Proper clothing and safety gear must be worn when operating unit.

Physical Condition Your judgment and physical dexterity may not be good: • if you are tired or sick, • if you are taking medication, • if you have taken alcohol or drugs. Operate unit only if you are physically and mentally well. Eye Protection Wear eye protection that meets ANSI Z87.1 or CE re quirements whenever you operate the unit Face and Head Protection When trimming overhead, always wear head protection meeting ANSI Z89.1 or CE requirements with a full face shield. Head protection with full face shield will help protect you from falling branches and debris. Hand Protection Wear no-slip, heavy duty work gloves to improve your grip on the unit handles. Gloves also reduce the transmis sion of machine vibration to your hands. WARNING Hearing Protection ECHO recommends wearing hearing protection when ever unit is used. Proper Clothing Wear snug fitting, durable clothing; • Pants should have long legs, shirts with long sleeves. • DO NOT WEAR SHORTS, • DO NOT WEAR TIES, SCARVES, JEWELRY, or clothing with loose or hanging items that could become entangled in moving parts or surrounding growth. Wear sturdy work shoes with nonskid soles; • DO NOT WEAR OPEN TOED SHOES, • DO NOT OPERATE UNIT BAREFOOTED. Wear no-slip, heavy duty work gloves. Keep long hair away from engine and air intake. Retain hair with cap or net. Hot Humid Weather Heavy protective clothing can increase operator fatigue which may lead to heat stroke. Schedule heavy work for early morning or late afternoon hours when temperatures are cooler.

The ignition components of this machine generate an electromagnetic field during operation which may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with pacemakers should consult with their physician and the pacemaker manufacturer before operating this machine. In the absence of such informa tion, ECHO does not recommend the use of ECHO products by anyone who has a pacemaker. Vibration and Cold It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sen sations followed by loss of color and numbness in the fingers. The following precautions are strongly recommended because the minimum exposure which might trigger the ailment is unknown. • Keep your body warm, especially the head, neck, feet, ankles, hands and wrists. • Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks and also by not smoking. • Limit the hours of operation. Try to fill each day with jobs where operating the unit or other hand-held power equipment is not required. • If you experience discomfort, redness, and swelling of the fingers followed by whitening and loss of feeling, consult your physician before further exposing yourself to cold and vibration. Power PrunerTM Operator's Manual 5 Repetitive Stress Injuries It is believed that overusing the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness, swelling, numbness, weakness and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years. To reduce the risk of RSI/CTS, do the following: • Avoid using your wrist in a bent, extended or twisted position. In stead try to maintain a straight wrist position. Also, when grasping, use your whole hand, not just the thumb and index finger. • Take periodic breaks to minimize repetition and rest your hands. • Reduce the speed and force with which you do the repetitive move ment. • Do exercises to strengthen the hand and arm muscles. • Immediately stop using all power equipment and consult a doctor if you feel tingling, numbness or pain in the fingers, hands, wrists or arms. The sooner RSI/CTS is diagnosed, the more likely permanent nerve and muscle damage can be prevented. danger All over head electrical conductors and communications wires can have electricity flow with high voltages. This unit is not insulated against electrical current. Never touch wires directly or indirectly when pruning, otherwise serious injury or death may result. warning Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. Read the Manuals • Provide all users of this equipment with the Operator’s Manual and Safety Manual for instructions on Safe Operation. Clear the Work Area • Spectators and fellow workers must be warned, and children and animals prevented from coming nearer than 15 m (50 ft.) while the unit is in use. Use Proper Clothing & Equipment • Always wear head protection with full face shield to help protect against falling branches and debris. Keep A Firm Grip • Grip Power PrunerTM with both hands with thumbs and fingers encir cling the handle, and shaft tube. 6 Keep A Solid Stance • Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not work in odd positions or on ladders. Do not overreach. • Operate the Power PrunerTM only from the ground or out of an ap proved bucket lift. • Always evaluate the branches to be pruned for hazards such as loose dead branches which may fall and strike the operator or helpers. Remove hazards before pruning. • Plan retreat path from falling objects. • Cut branches bounce when striking ground. • Check that shoulder harness is adjusted for safe, comfortable opera tion. See picture at right for proper adjustment. • Turn the Power PrunerTM off when moving from tree to tree. • Avoid any contact with saw chain. Avoid Hot Surfaces • Keep exhaust area clear of flammable debris. Avoid contact during and immediately after operation. kickback warning Kickback can lead to dangerous loss of control of the Power PrunerTM and result in serious injury to the operator or any one standing close by. Hold the Power PrunerTM firmly with both hands with thumbs and fingers encircling the front and rear handles. Be aware of the down and outward path the pruner will take after the cut is made. Kickback may occur when the moving saw chain at the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. In some cases this may cause a lightning-fast reverse action, kicking the guide bar and saw chain up and back or down and back towards the operator. Either of these reactions may cause the operator to lose control of the Power PrunerTM which could result in serious personal injury. With a basic understanding of kickback, you can reduce or eliminate the element of surprise which contributes to accidents. Avoid contact of the guide bar tip with any object while the saw chain is moving. Cut only wood. Avoid striking concrete, metal, wire, or other obstruc tions which could cause kickback or damage to the saw chain. If the saw chain does strike a foreign object, immediately stop the en gine, inspect and repair the Power PrunerTM if necessary. Power PrunerTM Operator's Manual 7 equipment WARNING Serious injury may result from the use of non approved guide bar and saw chain combinations. ECHO, INC. will not be responsible for the failure of cutting devices or accessories which have not been tested and approved by ECHO for use with this unit. Read and comply with all safety instructions listed in this manual. • Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed. Guide Bar and Saw Chain • Check that the cutting attachment, guide bar, and saw chain is firmly attached and in safe operating condition. • Use only one Echo-approved extension on the pruner. • Do not hit rocks, stones, tree stumps, and other foreign objects with the saw chain. • Do not cut into the ground with the saw chain. • If cutting attachment end strikes an obstruction, stop engine immediately and inspect saw chain for damage. • Do not operate with a dull, fractured, or discolored saw chain. • Remove all foreign objects from work area. • Always cover the guide bar and saw chain with guide bar cover during transportation and for storage. WARNING Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. • ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. • DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit. • NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings. WARNINg Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or leaks are found, do not use unit, otherwise serious personal injury or property damage may occur. Have unit repaired by an autho rized servicing dealer before using. 8 Emission Control (exhaust & evaporative) EPA 2010 and Later and/or C.A.R.B. TIER III The emission control system for the engine is EM (engine modification) and, if the second to last character of the Engine Family on the Emission Control Information label (sample below) is “C”, “K”, or “T”, the emission control system is EM and TWC (3-way catalyst). The fuel tank/fuel line emission control system is EVAP (evaporative emis sions). Evaporative emissions for California models are only applicable to fuel tanks. An Emission Control Label is located on the engine. (This is an EXAMPLE ONLY, information on label varies by engine FAMILY). PRODUCT EMISSION DURABILITY (EMISSION COMPLIANCE PERIOD) The 50 or 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emissions output meets applicable emissions regulations, provided that approved maintenance procedures are fol lowed as listed in the Maintenance Section of this manual. Description Locate this safety decal on your unit. Make sure the decals are legible and that you understand and follow the instruc tions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific information.

21 20 19 18 13 15 14 22 Hot Decal (near muffler)

16 17

8 7 6 5 4 8 7 6 9 9 Power PrunerTM Operator's Manual 9 PPT-266 10 11 12 1 2

5 4 10 11 2 PPT-266H 12 1

10 6 7 8 54 9 10 11 PPT-266S 1 12

3 2 Power PrunerTM Operator's Manual 11 1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Starter. 2. THROTTLE TRIGGER - Spring loaded to return to idle when released. During acceleration press trigger gradu ally for best operating technique. 3. SHOULDER HARNESS - An adjustable strap that suspends the unit from the operator. 4. CUTTING ATTACHMENT - Sealed, gear ratio is 1.5:1 reduction. 5. CUTTING SHOE - Used to capture and stabilize branch while cutting. Place cutting shoe against branch, acceler ate and lower saw chain into branch. 6. GUIDE BAR - 305 mm (12 in.) guide bar. 7. SAW CHAIN - Chain, serving as a cutting tool. 8. AUTOMATIC OILER ASSEMBLY - Self oiling. Use high quality, low viscosity, non detergent bar and chain oil. 9. LOWER SHAFT TUBE - Durable fiberglass mesh housing. 10. STOP SWITCH - Mounted on top of handle assembly. Move switch forward to run, back to stop. 11. THROTTLE TRIGGER LOCKOUT - This lever must be depressed before throttle trigger can be operated. 12. REAR HANDLE ASSEMBLY - Sturdy handle for right hand placement. Includes stop switch and throttle trigger. 13. TOP GUARD - Protects arm from hot engine. 14. RECOIL STARTER - Pull recoil handle slowly until starter engages, then quickly and firmly. When engine starts return handle slowly. DO NOT let handle snap back or damage will occur. 15. SPARK ARRESTOR - CATALYTIC MUFFLER / MUFFLER -The muffler or catalytic muffler controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Keep exhaust area clear of flammable debris. 16. FUEL TANK - Contains fuel and fuel filter. 17. FUEL TANK CAP - Covers and seals fuel tank opening. 18. CHOKE - Located above air cleaner housing. Move lever to starting position ( ) (close choke) and back to run position ( ) (open choke). 19. AIR CLEANER ASSEMBLY - Contains replaceable air filter elements. 20. PURGE BULB - Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging air from the carburetor. Pump purge bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump purge bulb an additional 4 or 5 times. 21. SPARK PLUG - Provides spark to ignite fuel mixture. 22. GUIDE BAR COVER - Used to cover guide bar and saw chain during transport and storage. Remove guide bar cover before using unit. 12 Contents Due to packaging restriction the ECHO product you have purchased requires some assembly. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts.

___ Power Head ___ Handle Shaft Assembly (PPT-266, PPT-266H Only) ___ Drive Shaft Assembly ___ Cutting Attachment W/ Guide Bar and Saw Chain ___ Operator's Manual ___ Emission Control Warranty Statement ___ Safety Manual ___ Warranty Registration Card ___ Assembly Tool (s) ___ Safety Glasses ___ Shoulder Harness ___ Guide Bar Cover Assembly Parts Required: Power Head, Handle Shaft Assembly, Drive Shaft Assembly, Cutting Attachment handle shaft / drive shaft (PPT-266, PPT-266H Models Only) 1. Remove protective caps from handle shaft assembly. 2. Loosen clamping bolts (A) on drive shaft. 3. Pull flexible drive shaft coupler (B) 2 -3 inches out of handle shaft. DECLARACIÓN DE GARANTÍA DE CONTROL DE EMISIONES DE ECHO INCORPORATED PARA LAS MARCAS ECHO Y SHINDAIWA La Agencia de Protección Medioambiental (EPA) y la Junta de Recursos de Aire de California (C.A.R.B.) y ECHO Incorporated (ECHO Inc.) tienen el placer de explicar la garantía del sistema de control de emisiones en su equipo o motor pequeño que no sea para desplazamiento por carretera (SORE) de 2010 o posteriores. Los nuevos equipos/SORE deben diseñarse, fabricarse y equiparse de modo que cumplan con las estrictas normas anticontami nación de EPA y CARB. ECHO Inc debe garantizar el sistema de control de emisiones en su equpo/SORE para los períodos citados a continuación, siempre que no haya habido ningún abuso, negligencia o mantenimiento indebido de su equipo/SORE. El sistema de control de emisiones puede incluir piezas tales como: carburador, sistema de inyección de combustible, sistema de encendido, convertidor catalítico/silenciador, depósito de combustible, líneas de alimentación de combustible, conjunto de tapa de combustible, bujías, filtros de aire y otros componentes relacionados. Donde exista una condición cubierta por la garantía, ECHO Inc reparará su equipo/SORE de forma gratuita, incluido el diagnóstico, las piezas y la mano de obra. La garantía del sistema de control de emisiones se extiende al propietario original incluidos todos los propietarios subsiguientes. COBERTURA DE GARANTÍA DEL FABRICANTE: El sistema de control de emisiones está garantizado durante 2 años o mientras dure la garantía de ECHO Inc, lo que sea más largo. Si cualquier pieza relacionada con las emisiones de su equipo es defectuosa, la pieza será reparada o reemplazada por ECHO Inc. o su representante de servicio autor izado. RESPONSABILIDADES DEL PROPIETARIO RELACIONADAS CON LA GARANTÍA: Como propietario del equipo/SORE, usted es responsable de llevar a cabo el mantenimiento requerido indicado en el manual del operador. ECHO Inc. recomienda que guarde todos los recibos de mantenimiento de su equipo/SORE, no obstante ECHO Inc. no puede negar la garantía solamente por falta de recibos o por no asegurarse de llevar a cabo todo el mantenimiento programado. Como propietario del equipo/SORE debe ser consciente de que ECHO Inc. puede rechazar su cobertura de garantía si su equipo/SORE o una pieza ha fallado debido abuso, negligencia, mantenimiento indebido o modificaciones no aprobadas. Usted es responsable de llevar a su equipo/SORE a un representante de servicio autorizado por ECHO Inc. tan pronto como surja un problema. Las reparaciones de garantía deben completarse en un período razonable, que no debe sobrepasar los 30 días. Si existe una condición cubierta por la garantía y no hay un distribuidor autorizado en un radio de 100 millas, ECHO Inc. pagará el envío de la unidad al distribuidor autorizado más cercano. Si tiene dudas sobre la cobertura de la garantía, debe ponerse en contacto con ECHO Inc. llamando al 1-800-673-1558, sitio web ECHO-USA. COM o ponerse en contacto con Shindaiwa al 1-877-986-7783, visitando el sitio web SHINDAIWA.COM. ¿QUE CUBRE ESTA GARANTÍA? ECHO Inc. garantiza que su equipo/SORE fue diseñado, fabricado y equipado para cumplir con las normas de emisiones de EPA y CARB correspon dientes y que su equipo/SORE no tiene defectos ni de material ni de elaboración que haga que no cumpla con los requisitos correspondientes durante 2 años o mientras dure la garantía de ECHO Inc., lo que sea más largo. El periodo de garantía empieza en la fecha en que el usuario final compre el producto. ¿CÓMO SE CORREGIRÁ UNA PIEZA CUBIERTA? Si hay un defecto en una pieza cubierta por esta garantía, cualquier Distribuidor de servicio autorizado de ECHO Inc. corregirá el defecto. No tendrá que pagar nada para ajustar, reparar o reemplazar la pieza. Esto incluye cualquier mano de obra y diagnóstico para reparaciones garantizadas por el distribuidor. Además estarán garantizadas las piezas de motor que no estén expresamente cubiertas por esta garantía pero cuya falla sea consecuencia de la falla de una pieza cubierta. ¿QUÉ PIEZAS ESTÁN CUBIERTAS? Cualquier pieza correspondiente relacionada con emisiones que no esté programada para el “mantenimiento requerido” será reparada o reemplazada en el período de garantía. La pieza reparada o reemplazada estará garantizada durante el resto del período de garantía de ECHO Inc. Cualquier pieza garantizada que esté programada solamente para su inspección regular en las instrucciones escritas proporcionadas está garantizada durante el período de garantía indicado arriba. Cualquier pieza reparada o reemplazada estará garantizada durante el resto del período de garantía de ECHO Inc. Cualquier pieza relacionada con emisiones programada para sustituirse durante el “mantenimiento requerido” estará garantizada durante el período antes del primer punto de sustitución programada para esa pieza. Cualquier pieza reparada o reemplazada cubierta por la garantía debe garantizarse durante el resto del período antes del primer punto de reemplazo programado para esa pieza. Cualquier pieza de repuesto aprobada por el fabricante puede usarse para llevar a cabo cualquier mantenimiento o reparaciones cubiertos por la ga rantía en las piezas relacionadas con las emisiones, y deben proveerse de forma gratuita si la pieza sigue cubierta por la garantía. Se puede usar cualquier pieza de repuesto que sea equivalente en rendimiento y durabilidad en el mantenimiento o reparaciones no cubiertos por la garantía y no debe reducir las obligaciones de la garantía del fabricante. Durante el peróodo de garantía del equipo/SORE, ECHO Inc. mantendrá un inventario de piezas garantizadas suficiente para cumplir con la demanda esperada de las mismas. PIEZAS GARANTIZADAS RELACIONADAS CON EMISIONES ESPECÍFICAS: • Sistema de encendido electrónico • Bujía • Conjunto de convertidor catalítico/silenciador • Carburador (conjunto completo o componentes de repuesto) • Estrangulado • Conjunto de inyección de combustible (o componentes de repuesto) • Depósito de combustible • Conjunto de tapa de combustible • Filtro de aire • Línea de alimentación de combustible (y abrazaderas/conectores relacionados correspondientes) ¿QUÉ NO ESTÁ CUBIERTO? Cualquier falla ocasionada por abuso, negligencia, mantenimiento indebido, modificaciones no aprobadas, uso de piezas agregadas no aprobadas/ piezas modificadas o accesorios no aprobados. Esta garantía de control de emisiones es válida solamente en EE.UU., sus territorios y Canadá. 99922201033 01/2010 A B

Power PrunerTM Operator's Manual 13 4. Align flexible drive shaft coupler with drive shaft socket and slide together until handle shaft is fully seated into drive shaft. 5. Tighten clamping bolts (A). A handle shaft / power head

1. Loosen two (2) clamping screws (A) and remove locating screw (B). 2. Pull flexible drive shaft coupler (C) 2-3 in. out of handle shaft as sembly. 3. Align flexible drive shaft coupler with engine socket and slide together until locating hole in shaft is visible through locating hole in engine housing. 4. Install locating screw (B) and tighten clamping bolts (A). AB C B A A

14 throttle linkage and ignition leads 1. Install throttle linkage cable into fan cover clip (A). A B D 2. Close choke and remove air filter cover. C 3. Place throttle linkage (B) through adjustment fixture (C) and install wire end into large carburetor throttle swivel hole (D). Check throttle for freedom of movement and that wide open throttle / low idle extremes are adjusted properly. The throttle linkage must be adjusted by moving the adjustment fixture (C). Consult with your Echo Dealer for correct adjustment procedure. E 4. Connect 2 ignition stop leads (E, F) from throttle cable tubing to 2 ignition leads (E, F) on engine. CAUTION: Assure ignition terminals are completely covered by clear plastic sleeves. F 5. Secure ignition leads against engine housing with clip (G). 6. Install air filter and cover. G Power PrunerTM Operator's Manual 15 cutting attachment to drive shaft installation warning Saw Chain is sharp! Always wear gloves when handling assembly, otherwise serious personal injury may result. 1. Loosen the two (2) screws (C) and locator screw (D) on cutting

attachment. 2. Loosen clamp knob (E) turning counter clockwise. 3. Pull upper tube (F) out of fiberglass lower tube 127-152 mm (5-6 in.), then slide (F) back into fiberglass lower tube exposing inner drive shaft (G). Align and join star shaped drive end of inner drive shaft (G) with cutting attachment shaft (H). 4. Align ridges (J) on upper tube with seams in cutting attachment. 5. Slide together aligning locator screw (D) in cutting attachment with locating hole (I) in upper tube. 6. Tighten locator screw (D). Tighten two (2) cutting attachment screws (C). C D F E G H J

G 7. Extend upper tube to desired length. Tighten clamp knob (E) turn ing clockwise. D I C 16 saw chain tension adjustment WARNING Always disconnect spark plug wire before servicing cutting attach ment. Wear gloves when handling saw chain, otherwise serious personal injury may result. To Adjust Saw Chain Tension 1. Move stop switch to STOP position. 2. Disconnect spark plug lead. 3. Loosen two guide bar nuts (A) until finger tight. IMPORTANT Always loosen guide bar nuts before turning the chain tension ad B juster, otherwise the clutch cover and tensioner will be damaged. A 4. Hold the bar nose up, and turn the adjuster screw (B) clockwise un til the chain fits snugly against the underside of the bar, as shown. Cold Chain Only - turn adjuster screw CW an additional 1/8 - 1/4 turn. 5. Tighten both guide bar nuts with nose held up. Tighten rear nut first. 6. Pull the chain around the guide bar by hand. Reduce the chain ten sion if you feel tight spots. 7. When chain is properly tensioned, tighten guide bar nuts securely. IMPORTANT Tighten guide bar nuts to 8 - 9 N•m (71 - 80 in. lbs.) DO NOT over-tighten nuts. Damage may result. 8. Keep chain properly tensioned at all times. NOTE All chains require frequent adjustment. 9. Connect spark plug lead. Power PrunerTM Operator's Manual 17 Operation WARNING Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. WARNING Operation of this equipment may create sparks that can start fires. This unit is equipped with a spark arrestor to prevent discharge of hot particles from the engine. Metal blade use also can create sparks if the blade strikes rocks, metal, or other hard objects. Contact local fire authorities for laws or regulations regarding fire prevention require ments. fuel NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage section of this manual. WARNING Alternative fuels, such as E-15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO requirements are NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels may cause performance prob lems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to, improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets, carbure tors and other engine components. Fuel Requirements Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol) is NOT approved. Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FD Standards must be used. Echo brand premium Power Blend X TM Universal 2-Stroke Oil meets these standards. Engine problems due to inadequate lubrication caused by failure to use an (ISO/CD 13738) and J.A.S.O. FD certified oil, such as Echo premium Power Blend X TM, will void the two-stroke engine warranty. IMPORTANT Echo premium Power Blend X TM Universal 2-Stroke Oil may be mixed at 50:1 ratio for application in all Echo en gines sold in the past regardless of ratio specified in those manuals. 18 Handling Fuel DANGER Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result. • Use an approved fuel container. • DO NOT smoke near fuel. • DO NOT allow flames or sparks near fuel. • Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize. • NEVER refuel a unit when the engine is HOT or RUNNING! • DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground. • DO NOT overfill fuel tank. Wipe up spills immediately. • Securely tighten fuel tank cap and close fuel container after refueling. • Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired. • Move at least 3m (10 ft.) from refueling location before starting the engine. Mixing Instructions 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of 2-stroke oil to gasoline. 3. Close container and shake to mix oil with gasoline. 4. Add remaining gasoline, close fuel container, and remix. IMPORTANT Spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-off containers to reduce fuel spillage. After use • DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel storage container. Storage - Fuel storage laws vary by locality. Contact your local govern ment for the laws affecting your area. As a precaution, store fuel in an approved, airtight container. Store in a well-ventilated, unoccupied building, away from sparks and flames. IMPORTANT Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added. IMPORTANT Stored two-stroke fuel may separate. ALWAYS shake fuel con tainer thoroughly before each use. Power PrunerTM Operator's Manual 19 lubricating the guide bar and saw chain Automatic Oiling System 1. Wipe debris from around oil fill cap. 2. Remove oil fill cap and fill reservoir with a quality, low viscosity guide bar and saw chain oil. NOTE The discharge volume of the automatic oiler is preset to deliver 3 to 4 cc/min. at normal operating RPM. During heavy or dry cutting conditions the oil discharge volume may be adjusted to assure ad equate lubrication. Refill the oil reservoir with each tank of fuel. IMPORTANT To prevent plastic deterioration, do not use synthetic or silicone based oil. adjusting automatic oiler 1. From bottom of gear case, turn adjustment screw (A) clockwise to decrease oil volume - counter clockwise to increase oil volume. A NOTE Very little visible oil on the saw chain will provide sufficient lubri cation.

20 starting cold engine WARNING The attachment will operate immediately when the engine starts, and could result in possible serious injury. Keep movable parts of the attachment away from objects that could become entangled or thrown, and surfaces that could cause loss of control. 1. Stop Switch Move stop switch button (A) forward away from the STOP position. 2. Choke Move choke (B) to “Cold Start” ( ) Position. 3. Purge Bulb Pump purge bulb (C) until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times. B 4. Recoil Starter Lay the unit on a flat, area and keep movable attachment parts clear of all obstacles. Firmly grasp right hand grip and throttle trigger lockout with left hand and fully depress throttle trigger to wide open position. Rapidly pull recoil starter handle/rope (D) until engine fires (or maximum five [5] pulls). 5. Choke After engine fires (or five [5] pulls), move choke lever back to “Run” ( ) position. Hold throttle trigger and throttle trigger lockout fully depressed and pull recoil starter handle/rope until engine starts and runs. Release throttle trigger and allow unit to warm up at idle for several minutes. NOTE If engine does not start with choke in “Run” position after 5 pulls, repeat instructions 2 - 5. 6. After engine warms up, gradually depress throttle trigger to in crease engine RPM to operating speed. A PPT-266 A PPT-266H/S D C PPT-266 PPT-266H/S D

Power PrunerTM Operator's Manual 21 starting warm engine The starting procedure is the same as Cold Start except DO NOT close the choke, and do not depress throttle trigger to wide open position. A PPT-266 WARNING The attachment should not move at idle, otherwise serious personal injury may result. NOTE

A If attachment moves, readjust carburetor according to “Carburetor Adjustment” instructions in this manual or see your ECHO Dealer. 1. Stop Switch. Move Stop Switch button (A) forward away from the STOP posi tion. 2. Purge Bulb Pump purge bulb (C) until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times. C 3. Recoil Starter. Lay the unit on a flat, clear area and firmly grasp right hand grip with left hand. Do not depress throttle trigger. Pull the recoil starter handle (D) until the engine fires. NOTE If engine does not start after 5 pulls, use Cold Start Procedure. D PPT-266H/S D PPT-266 PPT-266H/S 22 stopping engine 1. Throttle. Release throttle trigger, and allow engine to return to idle before stopping engine. 2. Stop Switch. Move stop switch button (A) backward to STOP position. A PPT-266

WARNING If engine does not stop when stop switch is moved to STOP posi tion, close choke - COLD START position - to stall engine. Have your ECHO dealer repair stop switch before using pruner again. pruning techniques WARNING Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause unconsciousness, serious in jury, or death. Exhaust can cause serious burns. ALWAYS position unit so that exhaust is directed away from your face and body. The Power PrunerTM is designed for light to medium trimming of limbs and branches up to 203 mm (8 in.) in diameter. Follow these tips for successful operation. • Plan cut carefully. Check direction branch will fall. • Plan retreat path from falling branch. Cut branches bounce when striking ground. • Long branches should be removed in several pieces. • Do not stand directly beneath branch being cut. • When ready to cut: Hold "cutting shoe" against branch. This will prevent whipping of the branch. DO NOT use back and forth sawing action. A CORRECT GUIDE AGAINST BRANCH NOT CORRECT PPT-266H/S

• Look out for branch immediately behind the branch being cut. If saw chain hits rear branch damage to saw chain may occur. • Accelerate to full throttle. • Apply cutting pressure. • Ease cutting pressure when nearing end of cut to maintain control. • When pruning a limb 102 mm (4 in.) diameter or larger cut as fol lows: 1. Under cut 1/4 limb diameter near tree trunk. 2. Finish top cut slightly farther out on limb. 3. Flush cut stub at trunk. • DO NOT use for felling or bucking. BLADE HITS REAR BRANCH NOT CORRECT

Power PrunerTM Operator's Manual 23 Maintenance WARNING Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Your ECHO Power PrunerTM is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your pruner achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOUR SELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed see your ECHO Dealer for repairs. skill level Level 1 = Easy to do. Common tools may be required. Level 2 = Moderate difficulty. Some specialized tools may be required. ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier. maintenance intervals

COMPONENT / SYSTEM MAINTENANCE PROCEDURE REQ'D SKILL LEVEL DAILY OR BEFORE USE EVERY REFUEL 3 MONTHS YEARLY

Air Filter Inspect/Clean 1 I / C * R * Choke Shutter Inspect/Clean 1 I / C Fuel Filter Inspect/Replace 1 I * I / R * Fuel Cap Gasket Inspect/Replace 1 I * R * Fuel System Inspect/Replace 1 I (2) * I (2) * Spark Plug Inspect/Clean/Replace 1 I/C/R * Cooling System Inspect/Clean 2 I / C Muffler Spark Arrestor Inspect/Clean/Replace 2 I/C/R * Cylinder Exhaust Port Inspect/Clean/Decarbon 2 I / C Drive Shaft (Flex Cable Models) Inspect/Grease 2 I (1) Guide Bar / Sprocket Nose Inspect/Clean/Lubricate 2 I / C * I Saw Chain Inspect/Sharpen/ Replace/Tension 2 I * I * Recoil Starter Rope Inspect/Clean 1 I / C * Screws/Nuts/Bolts Inspect/Tighten/Replace 1 I * MAINTENANCE PROCEDURE LETTER CODES: I = INSPECT, R = REPLACE, C = CLEAN IMPORTANT NOTE - Time intervals shown are maximum. Actual use and your experience will determine the frequency of required maintenance. MAINTENANCE PROCEDURE NOTES: (1) Apply grease every 25 hours of use. (2) Low evaporative fuel tanks DO NOT require regular maintenance to maintain emission integrity. * All recommendations to replace are based on the finding of damage or wear during inspection. 24 air filter Level 1. Parts required: REPOWERTM AIR & FUEL FILTER KIT. 1. Close choke (cold start position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumu lated dirt from air cleaner area. 2. Remove air filter cover and air filter retainer from inside cover. Brush dirt from inside cover. 3. Replace filter if it is damaged, very dirty, or the rubber sealing edges are deformed. 4. Remove foam pre-filter and air filter and clean as indicated below: Foam Pre-filter • Clean foam filter in water/detergent solution and rinse with clean water. • Wrap the filter in a clean, dry cloth and squeeze (do not wring) dry. Allow to dry completely before reuse. Do not oil. Dual Layer Air Filter • Lightly brush debris from filter. • Soak heavily soiled filters in water/detergent solution to loosen dirt, then brush lightly. • Rinse with clean water and allow to dry completely before reuse. 5. Place foam pre-filter over raised center and inside outer lip of air filter. Install air filter in air filter case. 6. Install air filter retainer on post in air filter cover, flat side up. 7. Install air filter cover and tighten cover knob securely. fuel filter Level 1. Parts required: REPOWERTM AIR & FUEL FILTER KIT. DANGER Fuel is VERY flammable. Use extreme care when mixing, storing or handling, or serious personal injury may result. 1. Use a clean rag to remove loose dirt from around fuel cap and empty fuel tank. 2. Use the “fuel line hook” to pull the fuel line and filter from the tank. 3. Remove the filter from the line and install the new filter. NOTE Federal EPA regulations require all model year 2012 and later gasoline powered engines produced for sale in the United States to be equipped with a special low permeation fuel supply hose between the carburetor and fuel tank. When servicing model year 2012 and later equipment, only fuel supply hoses certified by EPA can be used to replace the original equipment supply hose. Fines up to $37,500 may be enforced for using an un-certified replacement part. Power PrunerTM Operator's Manual 25 spark plug Level 2. Parts Required: REPOWERTM Tune-Up Kit IMPORTANT Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada) oth erwise severe engine damage may occur. 1. Remove spark plug and check for fouling, worn and rounded center electrode. 2. Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage engine. 0.65 mm

3. Adjust spark plug gap 0.65mm (0.026 in.) by bending outer elec trode. 4. Tighten spark plug to 150-170 kgf • cm (130-150 in • lbf). cooling system cleaning Level 2. Parts Required: None. IMPORTANT To maintain proper engine operating temperatures, cooling air must pass freely through the cylinder fin area. This flow of air carries combustion heat away from the engine. Overheating and engine seizure can occur when: • Air intakes are blocked, preventing cooling air from reaching the cylinder. • Dust and grass build up on the outside of the cylinder. This build up insulates the engine and prevents the heat from leaving. Removal of cooling passage blockages or cleaning of cooling fins is considered “Normal Maintenance.” Any failure attributed to lack of maintenance is not warranted. (0.026 in.)

26 1. Remove spark plug lead. 2. Remove air cleaner cover. 3. Remove muffler cover (A). 4. Remove engine cover (B). IMPORTANT DO NOT use a metal scraper to remove dirt from the cylinder fins. 5. Use brush to remove dirt from the cylinder fins. 6. Remove grass and leaves from the grid between the recoil starter and fuel tank. 7. Assemble components in reverse order. exhaust system Spark Arrestor Screen Level 2. Parts Required: Spark Arrestor Screen, Gasket 1. Remove muffler cover (A). 2. Place piston at Top Dead Center (TDC) to prevent carbon/dirt from entering cylinder. 3. Remove spark arrestor screen (B), gasket (C) and exhaust guide (D) from muffler body. 4. Clean carbon deposits from muffler components. NOTE When cleaning carbon deposit, be careful not to damage the cata A B A C

lytic element inside muffler. B D 5. Replace screen if it is cracked, plugged or has holes burned through. 6. Assemble components in reverse order. Power PrunerTM Operator's Manual 27 Exhaust Port Cleaning Level 2. Parts Required: As needed: Heat Shield

1. Remove spark plug lead from spark plug, and remove muffler cover. 2. Place piston at top dead center. Remove muffler (A) and heat shield (B). 3. Use a wood or plastic scraping tool to clean deposits from cylinder exhaust port. IMPORTANT Never use a metal tool to scrape carbon from the exhaust port. Do not scratch the cylinder or piston when cleaning the exhaust port. Do not allow carbon particles to enter the cylinder. 4. Inspect heat shield, and replace if damaged. 5. Install heat shield and muffler. 6. Tighten muffler mounting bolts (or nuts) to 60-70 in•lbf (70-80 kgf•cm). 7. Install muffler cover and attach spark plug lead. 8. Start engine, and warm to operating temperature. 9. Stop engine, and re-tighten mounting bolts (or nuts) to specifica tions. B A

28 carburetor adjustment Engine Break-In New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. During the break in period your engine performance will increase and exhaust emissions will stabilize. Idle speed can be adjusted as required. High Altitude Operation This engine has been factory adjusted to maintain satisfactory starting, emission, and durability performance up to 1,100 feet above sea level (ASL) (96.0 kPa). To maintain proper engine operation and emission compliance above 1,100 feet ASL the carburetor may need to be ad justed by an authorized ECHO service dealer. Important If the engine is adjusted for operation above 1,100 feet ASL, the carburetor must be re-adjusted when operating the engine below 1,100 feet ASL, otherwise severe engine damage may result. Level 2. Parts required: None. NOTE Every unit is run at the factory and the carburetor is set in compli ance with emission regulations. Carburetor adjustments, other than idle speed, must be performed by an authorized ECHO dealer. 1. Check idle speed and reset if necessary. If a tachometer is avail able, idle speed screw (A) should be set to the specifications found on "Specifications" page of this manual. Turn idle screw (A) clockwise to increase idle speed; counter clockwise to decrease A idle speed. WARNING When carburetor adjustment is completed, the cutting attachment should not turn at idle, otherwise serious personal injury may result. Power PrunerTM Operator's Manual 29 lubrication Flexible Drive Shaft Level 1. Parts required: POWER BLENDXTM 14 oz. or Lithium Based Grease. 1. Loosen clamping screws (A) on driveshaft coupling. 2. Remove handle and flexible drive shaft. 3. Remove flexible drive shaft (B).

4. Wipe flex shaft clean and apply a thin coating of grease. 5. Slide flex shaft into handle. Leave 2 - 3 inches of flex shaft ex posed. DO NOT get dirt on flex shaft. 6. Align flexible drive shaft with drive shaft socket, and slide together until handle is fully seated into drive shaft coupling. 7. Tighten clamping screws (A). A B B

30 guide bar and saw chain replacement WARNING Never try to replace or adjust guide bar and saw chain with engine running. Always disconnect spark plug wire before servicing guide bar and saw chain. This saw chain is VERY sharp, wear heavy gloves to protect your hands when handling it. Wear eye protection meeting CE or ANSI specification Z87.1. Guide Bar Replacement / Installation Level 2 1. Remove two (2) guide bar nuts (A), and unscrew sprocket cover screw (B).

2. Remove sprocket cover (D). 3. Remove guide bar and saw chain from gear case and sprocket. 4. Remove chain from guide bar and check guide bar for damage and excessive or uneven wear. Replace guide bar if necessary. 5. Install chain on guide bar with cutters on top of bar facing toward bar tip. 6. Install guide bar and chain on gear case, engaging chain with drive sprocket (E). 7. Turn tension adjustment screw (C) to ensure chain tension adjuster pin fits into the guide bar adjuster hole. 8. Install sprocket cover (D), tighten guide bar nuts (A) finger tight, and fasten sprocket cover screw (B). 9. Adjust chain tension. DB C E DB A

C A Power PrunerTM Operator's Manual 31 Sprocket Cover Cleaning

1. Remove two (2) guide bar nuts (A), and unscrew sprocket cover screw (B). 2. Remove sprocket cover (D). 3. Gently brush debris from inside guide bar cover and from around sprocket. 4. Turn tension adjustment screw (C) to ensure chain tension adjuster pin fits into the guide bar adjuster hole. 5. Install sprocket cover (D), tighten guide bar nuts (A) finger tight, and fasten sprocket cover screw (B). 6. Adjust chain tension. To Adjust Saw Chain Tension WARNING Always disconnect spark plug wire before servicing cutting attach ment. Wear gloves when handling saw chain, otherwise serious personal injury may result. To Adjust Saw Chain Tension 1. Move stop switch to STOP position. 2. Disconnect spark plug lead. 3. Loosen two guide bar nuts (A) until finger tight. IMPORTANT Always loosen guide bar nuts before turning the chain tension ad juster, otherwise the clutch cover and tensioner will be damaged. 4. Hold the bar nose up, and turn the adjuster screw (B) clockwise un til the chain fits snugly against the underside of the bar, as shown. Cold Chain Only - turn adjuster screw CW an additional 1/8 - 1/4 turn. 5. Tighten both guide bar nuts with nose held up. Tighten rear nut first. 6. Pull the chain around the guide bar by hand. Reduce the chain tension if you feel tight spots. 7. When chain is properly tensioned, tighten guide bar nuts securely. IMPORTANT Tighten guide bar nuts to 8 - 9 N•m (71 - 80 in. lbs.) DO NOT over-tighten nuts. Damage may result. 8. Keep chain properly tensioned at all times. NOTE All chains require frequent adjustment. 9. Connect spark plug lead. DB C B A A

32 Power Pruner B&C Combinations Bar P/N Chain P/N Chain Type Links Pitch Gauge Narrow Kerf 10" narrow bar P/N 10A4CD3739 90S39CQ 90 39 3/8" 0.043 12" narrow bar P/N 12A4CD3744 90S44CQ 90 44 3/8" 0.043 Regular 10" regular bar P/N 10A0CD3739 91VXL39CQ 91 39 3/8" 0.050 12" regular bar P/N 12A0CD3744 91VXL44CQ 91 44 3/8" 0.050 IMPORTANT Check bar Part Number on your Power Pruner. Chain and guide bar gauge size must be identical. Use Bar/Chain combinations shown in table above. Power PrunerTM Operator's Manual 33 filing saw chain

Level 2. 1 IMPORTANT Dull or damaged cutters will result in poor cutting performance, increased vibration, and premature saw chain failure. 2 WARNING Always stop engine and disconnect spark plug wire before servic ing guide bar and saw chain. Always wear gloves when filing saw chain, otherwise serious personal injury may result. 3 1. Set round file (A) in cutter at 30° angle. One fifth (1/5) of the file should be exposed above top cutter edge. 2. Keep file horizontal in cutter and file in one direction. 3. File until cutter top and side bevel edges are sharp without nicks. 4 4. Place depth gauge tool (B) firmly on top of cutter with .025 in. slot and end against front cutter raker. File cutter raker with flat file until flush with top of depth gauge. 5. Finish cutter sharpening by rounding front raker edge (C) with flat 5 file. 6 6. Properly filed cutter is as shown. 7. Apply clean oil and rotate saw chain slowly to wash away filings. 8. If saw chain is coated or clogged with resin, clean in kerosene, then 30° 90° (TOP PLATE ANGLE) (TOP PLATE CUTTING ANGLE) soak in oil. (DEPTH GAUGE)

34 Troubleshooting TRAHCGNITOOHSELBUORTMELBORPENIGNE

P k melbor C s ceh S e utat C y sua demeR

F r roterubractaleu N d oterubractaleufo eggolcreniartsleuF deggolcenilleuF roterubraC ecalperronaelC ecalperronaelC relaedohcEruoyeeS

enignE -sknarc /drahstrats t'nseod F r rednilyctaleu N r ednilyctaleufo C r oterubra elaedohcEruoyeeS M h leufhtiwtewrelffu F e cirooterutxiMleu kohcnepO retlifriaecalper/naelC roterubractsujdA relaedohcEruoyeeS

trats dnetakrapS eriwgulpfo N f krapso fohctiwspotS melborplacirtcelE hctiwskcolretnI NOothctiwsnruT relaedohcEruoyeeS relaedohcEruoyeeS

S k gulptakrap N t rapso cerrocnipagkrapS nobrachtiwderevoC leufhtiwdeluoF evitcefedgulP ).ni620.0(mm56.ottsujdA ecalperronaelC ecalperronaelC gulpecalpeR

A y retlifri A r tridretlifri N e aewlamro calperronaelC

,snurenignE roseidtub F y retlifleu F s tridretlifleu C n eudiser/stnanimatno i leuf F d tnevleu F n eggulptnevleu iseudiser/stnanimatnoC leuf ecalpeR ecalperronaelC

tonseod etarelecca ylreporp S n gulPkrap P r row/ytridgul N e aewlamro calperrotsujdadnanaelC C t roterubra I n nemtsujdareporpm V t oitarbi sujdA

C m metsySgniloo etsysgnilooC deggulp/ytrid ninoitarepodednetxE snoitacolytsud/ytrid naelC rotserrAkrapS neercS rotserrakrapS deggulpneercs N e raewlamro calpeR

seodenignE knarcton DANGER N A A/ N m / I r elborpenignelanretn elaedohcEruoyeeS

Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by ground ing spark plug near cylinder plug hole, otherwise serious personal injury may result. Power PrunerTM Operator's Manual 35 Storage warning During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result. Long Term Storage (over 30 days) Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage mainte nance which includes the following: 1. Store unit in a dry, dust free place, out of the reach of children. DANGER Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark or serious personal injury may result.

2. Place the stop switch in the "OFF" position. 3. Remove accumulation of grease, oil, dirt and debris from exterior of unit. IMPORTANT Some tree sap and resins are corrosive. Thoroughly wash the guide bar and sprocket areas after each use, then coat metal parts with light oil. 4. Perform all periodic lubrication and services that are required. 5. Tighten all the screws and nuts. 6. Drain fuel tank completely. Press purge bulb 6 -7 times to remove remaining fuel from carburetor then drain the tank again. Close choke, start and run the engine until it stops due to lack of fuel. 7. A. Allow engine to cool then remove the spark plug and pour 7 cc (1/4 oz.) of fresh, clean, two-stroke engine oil into the cylinder through the spark plug hole. B. Pull the recoil starter handle 2-3 times to distribute the oil inside the engine. C. Observe the piston location through the spark plug hole. Pull the recoil starter handle slowly until the piston reaches the top of its travel and leave it there. 8. Install the spark plug (do not connect spark plug cable). 9. Install the guide bar cover on the guide bar and saw chain during storage.

36 Specifications MODEL ---------------------------------------------------- PPT-266/H/S Length (Standard) (PPT-266/H) ------------------------- 2.72 m (8 ft. 11 in.) Length (Standard) (PPT-266S) --------------------------- 1.96 m (6 ft. 5 in.) Length (Extended) (PPT-266/H) ------------------------- 3.71 m (12 ft. 2 in.) Length (Extended) (PPT-266S) -------------------------- 2.41 m (7 ft. 11 in.) Length w/extension (PPT-266/H) ------------------------ 4.93 m (16 ft. 2 in.) Length w/extension (PPT-266S) ------------------------- 3.94 m (12 ft. 11 in.) Width (PPT-266/H) ---------------------------------------- .25 m (9.8 in.) Width (PPT-266S) ----------------------------------------- .25 m (9.8 in.) Height (PPT-266/H) --------------------------------------- .25 m (9.7 in.) Height (PPT-266S/H)-------------------------------------- .25 m (9.7 in.) Weight (dry) (PPT-266) ----------------------------------- 8.4 kg (18.5 lb.) Weight (dry) (PPT-266H) --------------------------------- 8.2 kg (18.0 lb.) Weight (dry) (PPT-266S) --------------------------------- 7.5 kg (16.5 lb.) Engine Type ------------------------------------------------ Air cooled, two-stroke, single cylinder gasoline engine Bore ---------------------------------------------------------- 34.0 mm (1.34 in.) Stroke -------------------------------------------------------- 28.0 mm (1.10 in.) Displacement ----------------------------------------------- 25.4 cc (1.55 cu. in.) Exhaust System -------------------------------------------- Spark arrestor - catalytic muffler / muffler Carburetor--------------------------------------------------- Diaphragm model w/purge pump Ignition System -------------------------------------------- CDI (capacitor discharge ignition) Spark Plug -------------------------------------------------- NGK BPM-8Y Gap 0.65 mm (0.026 in.) Fuel ---------------------------------------------------------- Mixed (Gasoline and Two-stroke Oil) Fuel/Oil Ratio ---------------------------------------------- 50 : 1 Power Blend X™ ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345- FD, two-stroke, air-cooled engine oil. Gasoline ----------------------------------------------------- Use 89 Octane unleaded. Do not use fuel containing methyl alcohol, more than 10% ethyl alcohol or 15% MTBE. Do not use alternative fuels such as E-15 or E-85. Oil ------------------------------------------------------------ Power Blend X TM Premium Universal 2-Stroke Oil Fuel Tank Capacity ---------------------------------------- 0.50 lit. (16.9 US fl. oz.) Starter System ---------------------------------------------- Automatic Recoil Starter Clutch-------------------------------------------------------- Centrifugal Type Sprocket Type ---------------------------------------------- 6 tooth spur, 9.53 mm (3/8 in.) pitch Power Transmission Shaft Assembly ------------------- Aluminum Extrusion Gear Case Ratio -------------------------------------------- 1.5:1 Oiling System ---------------------------------------------- Automatic Saw Chain Oil Capacity ---------------------------------- 225 ml (7.6 oz.) Handle ------------------------------------------------------- Right hand grip w/throttle trigger and lockout Shoulder Harness ------------------------------------------ Standard Idle Speed (RPM) ------------------------------------------ 2,850 Clutch Engagement Speed (RPM) ----------------------- 3,900 Wide Open Throttle Speed (RPM) ---------------------- 10,750 Guide Bar and Saw Chain (91) -------------------------- 305 mm (12 in.); 9.53 mm (3/8 in.) pitch, 0.050 gauge Power PrunerTM Operator's Manual 37 Warranty Statements ECHO LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO'S RESPONSIBILITY ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship. Under normal use and maintenance from date of purchase, ECHO agrees to repair or replace at ECHO’s discretion, any defective product free of charge at any authorized ECHO servicing dealer within listed below application time periods, limitations and exclusions. THIS LIMITED WARRANTY IS ONLY APPLICABLE TO ECHO PRODUCTS SOLD BY AUTHORIZED ECHO DEALERS. IT IS EXTENDED TO THE ORIGINAL PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any damage caused by improper installation or improper maintenance is not covered by this warranty. All parts or products replaced under warranty become the property of ECHO, Inc. This warranty is separate from the Emission control warranty statement supplied with your new product. Please consult the Emission Control Warranty Statement for details regarding emission related parts. For a list of Authorized ECHO Dealers refer to ECHO-USA.COM or call 1-800-432-ECHO. OWNER’S RESPONSIBILITY To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at ECHO-USA.COM or by fill ing out the warranty registration card supplied with your unit. Registering your product confirms your warranty coverage and provides a direct link if we find it necessary to contact you. The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in the operator’s manual. Should a product difficulty occur, you must, at your expense, deliver or ship your ECHO unit to an authorized ECHO servicing dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been made. For your nearest authorized ECHO servicing dealer, call ECHO’s Dealer Referral Center, at 1-800-432-ECHO or you can locate an ECHO servicing dealer at ECHO-USA.COM. Should you require assistance or have questions concerning ECHO’s Warranty Statement, you can contact our Consumer Product Support Department at 1-800-673-1558 or contact us through the web at ECHO-USA.COM. PRODUCT WARRANTY PERIOD RESIDENTIAL APPLICATION • 5 YEAR WARRANTY - All units for residential, or non-income producing use will be covered by this limited warranty for five (5) years from date of purchase. EXCEPTIONS: • For two-stroke engine powered products, the electronic ignition module, flexible drive cables, SRM solid drive shafts, and TC tines are warranted for the life* of the product on parts only. • Cutting attachments such as, but not limited to, bars, chains, sprockets, blades, and nylon trimmer heads for residential or non-income producing use will be covered for failures due to defects in material or workmanship for a period of 60 days from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty. • ECHO’s Rapid Loader String Head carries a lifetime warranty on the line locking system, parts only; no labor. Refer to your operator’s manual for string head installation and maintenance instructions. • All SB-Series and PRO ATTACHMENT SERIES Split Shaft attachments carry the same warranty duration as the units they are designed to fit. COMMERCIAL APPLICATION • 1 YEAR WARRANTY - All Chain Saws, QuikVent Saws, and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income producing use will be covered by this limited warranty for one (1) year from the date of purchase. • 2 YEAR WARRANTY - All other units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this limited warranty for two (2) years from the date of purchase. EXCEPTIONS: • For two-stroke engine powered products, the electronic ignition module, flexible drive cables, SRM solid drive shafts and TC tines, are warranted for the life* of the product on parts only. • Cutting attachments such as, but not limited to, bars, chains, sprockets, blades, and nylon trimmer heads for commercial, institutional, agricultural, industrial, rental, or income producing will be covered for failures due to defects in material or workmanship for a period of 30 days from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty. • ECHO’s Rapid Loader String Head carries a lifetime warranty on the line locking system, parts only; no labor. Refer to your operator’s manual for string head installation and maintenance instructions. • All SB-Series and PRO ATTACHMENT SERIES Split Shaft attachments carry the same warranty duration as the units they are designed to fit. RENTAL APPLICATION - 90 DAYS WARRANTY • Units for rental use will be covered against defects in material and workmanship for a period of 90 days from the date of purchase. * ECHO’s liability under the “Lifetime” coverage is limited to furnishing parts specified under the PROdUCT wARRANTy PERIOd section of this warranty statement for “Life” free of charge for a period of ten (10) years after the date of the complete unit’s final production. 38 PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES • 90-day residential, or non-income producing warranty • 30-day commercial, institutional, agricultural, industrial, income producing, or rental application warranty ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior performance. To help ensure the performance of the unit, it is required to use two-stroke oil which meets the ISO-L-EGD Standard per ISO/CD 13738 and JASO M345FD Standards. ECHO Power Blend™ Two-Stroke Oil is a premium two-stroke oil specifically formulated to meet ISO L-EGD (ISO/CD 13738) and JASO M345FD Standards. The use of two-stroke oils designed for other applications, such as for outboard motors or lawnmowers can result in severe engine damage, and will void your two-stroke engine limited warranty. THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY: • Lack of lubrication or engine failure, due to the use of two-stroke oils that do not meet the ISO-L-EGD (ISO/CD 13738) and JASO M345FD Standards. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD compliant and JASO M345FD registered oil, will void the two-stroke engine limited warranty. ECHO Power Blend™ Two-Stroke Oil meets the ISO-L-EGD and JASO M345FD Standard. Emission related parts are covered for 5 years residential use or 2 years commercial use regardless of two-stroke oil used, per the statement listed in the EPA or California Emission Defect Warranty Explanation. • damage caused by use of gasohol, containing methanol (wood alcohol), or gasoline containing less than 89 octane. Only use gasoline which contains 89 octane or higher. Gasohol which contains a maximum 10% ethanol (grain alcohol) or 15% MTBE (methyl/tertiary/butyl/ether) is also approved. The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator’s manual. • Engine damage caused by use of ether or any starting fluids. • damage caused by tampering with engine speed governor or emission components, or running engines above specified and recommended engine speeds as listed in your operator’s manual. • Operation of the unit with improperly maintained/removed cutting shield or removed/damaged air filter. • damage caused by dirt, pressure or steam cleaning the unit, salt water, corrosion, rust, varnish, abrasives, and moisture. • defects, malfunctions or failures resulting from abuse, misuse, neglect, modifications, alterations, normal wear, improper servicing, or use of unauthorized attachments. • Incorrect storage procedures, stale fuel, including failure to provide or perform required maintenance services as prescribed in the operator's manual. Preventative maintenance as outlined in the operators manual is the customer’s responsibility. • Failures due to improper set-up, pre-delivery service or repair service by anyone other than authorized ECHO servicing dealer during the warranty period. • Certain parts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups. • Use of spark plugs other than those meeting performance and durability requirements of the OEM spark plug listed in the Operator's Manuals. • Overheating or carbon scoring failures due to restricted, clogged exhaust port or combustion chamber, including damage to spark arrester screen. • Adjustments after the first (30) thirty days and beyond, such as carburetor adjustment and throttle cable adjustment. • damage to gears or gear cases caused by contaminated grease or oil, use of incorrect type or viscosity of lubricants, and/or failure to comply with recommended grease or oil change intervals. • damage caused by loading SHREd 'N' VAC® beyond recommended capacity. • damage caused by pump or sprayer running dry, pumping or spraying caustic or flammable materials, or lack of or broken strainers. • Additional damage to parts or components due to continued use after operational problem or failure occurs. Should operational problem or failure occur, the product should not be used, but delivered as is to an authorized ECHO servicing dealer. It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your ECHO product or by visiting ECHO-USA.COM. your receipt of purchase including date, model and serial number must be maintained and presented to an authorized ECHO servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so you may also have other specific legal rights which vary from state to state. This limited warranty is given by ECHO Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047. DISCLAIMER OF IMPLIED WARRANTIES This limited warranty is in lieu of all other expressed or implied warranties, including any warranty of FITNESS FOR A PARTICULAR PURPOSE OR USE and any implied warranty of MERCHANTABILITY otherwise applicable to this product. ECHO and its affiliated companies shall not be liable for any special incidental or consequential damage, including lost profits. There are no warranties extended other than as provided herein. This limited warranty may be modified only by ECHO. 99922201032 11/18/2011 Power PrunerTM Operator's Manual 39 notes

Servicing Information parts/serial number Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer. When you do need to buy parts always have the Model Num ber, Type and Serial Number of the unit with you. You can find these numbers on the engine housing. For future reference, write them in the space provided below. Model No. _________________SN. ___________________ service Service of this product during the warranty period must be performed by an Authorized ECHO Service Dealer. For the name and address of the Authorized ECHO Service Dealer nearest you, ask your retailer or call: 1-800-432-ECHO (3246). Dealer information is also available on our Web Site. When presenting your unit for Warranty service/repairs, proof of purchase is required. echo consumer product support If you require assistance or have questions concerning the applica tion, operation or maintenance of this product you may call the ECHO Consumer Product Support Department at 1-800-673-1558 from 8:30 am to 4:30 pm (Central Standard Time) Monday through Friday. Before calling, please know the model and serial number of your unit. warranty registration To ensure trouble free warranty coverage it is important that you regis ter your Echo equipment on-line at echo-usa.com or by filling out the warranty registration card supplied with your unit. Registering your product confirms your warranty coverage and provides a direct link between you and ECHO if we find it necessary to contact you. additional or replacement manuals DEALER? Call 1-800-432-ECHO 1-800-432-3246 or echo-usa.com CONSUMER PRODUCT SUPPORT 1-800-673-1558 8:30 - 4:30 Mon - Fri C.S.T.

Replacement Operator, Safety Manuals, and Parts Catalogs are available from your ECHO dealer or at echo usa.com or by contacting ECHO Inc., 400 Oakwood Road, Lake Zurich, IL 60047 (800-673-1558). Always check the ECHO Web Site for updated information. Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video. ECHO, INCORPORATED

E04111001001/E04111003677 E04212001001/E04212020704 400 Oakwood Road Lake Zurich, IL 60047 echo-usa.com (H) E04411001001/E04411001246 (H) E04512001001/E04512003183(S) E04711001001/E04711999999 (S) E04812001001/E04812999999


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply