DSC PC6311 (01) PDF MANUAL


Post questions, comments, reviews or errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD DSC PC6311 (01) PDF MANUAL


PDF Content Summary: Limited Warranty DSC warrants that for a period of one year from the date of purchase, the product shall be free of defects in material and workmanship under normal use and that in fulfillment of any breach of such warranty, DSC shall, at its option, repair or replace the defective equipment upon return of the equipment to its repair depot. This warranty applies only to defects in materials and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond the control of DSC, such as lightning, excessive voltage, mechanical shock, water dam- age or damage arising out of abuse, alteration or improper application of the product. The foregoing warranty shall apply only to the original buyer, and shall be in lieu of any and all other warranties, whether expressed or implied and of all other obligations or liabilities on the part of DSC. This warranty contains the entire warranty. DSC neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf, to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. In no event shall DSC be liable for any direct, indirect or consequential damages, loss of antic- ipated profits, loss of time or any other losses incurred by the buyer in connection with the pur- chase, installation or operation or failure of this product. Important! DSC recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to but not limited to criminal tampering or electrical dis- ruption, it is possible for this product to fail to perform as expected. PC6311 v1.0 Backbone Repeater Installation Instructions The PC6311 backbone repeater extends the backbone bus up to 305 meters (1000 feet) and pro- vides isolation from downstream short circuits. A maximum of three modules may be connected in series from the signal source. The maximum distance between two communicating devices can not exceed 1220m (4000ft) in a ‘Star’ or ‘Daisy Chain’ configuration. Two LEDs located on the module are provided for diagnostics. CH1 CH1 CH2 CH2 LED's Mounting Holes for Standoffs CH2 CH2 RED1 BLK1 YEL1 GRN1 RED2 BLK2 YEL2 GRN2 • Compatible cabinets RED2 BLK2 YEL2 GRN2 • Compatible cabinets FCC COMPLIANCE STATEMENT CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursu- ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television recep- tion, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‘ Re-orient the receiving antenna. ‘ Increase the separation between the equipment and receiver. ‘ Connect the equipment into an outlet on a circuit different from that to which the receiver is con- nected. ‘ Consult the dealer or an experienced radio/television technician for help. The user may find the following booklet prepared by the FCC useful: “How to Identify and Resolve Radio/Television Interference Problems”. This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4. ©2001 Digital Security Controls Ltd. Toronto • Canada • 1-800-387-3630 • dsc.com Printed in Canada 29005849 R002 Specifications • Voltage...12VDC ( 9-15VDC) • Current...10mA (nom.) • Maximum distance between two repeat- ers, or repeater and control panel... 305m (1000 ft) • Maximum capacitance...50 nF/305M • Maximum signal path distance with repeaters ...1220m (4000ft) RED2 BLK2 YEL2 GRN2 • Compatible cabinets RED2 BLK2 YEL2 GRN2 • Compatible cabinets • PC4002C/5C/6C • PC4002C/5C/6C • PC5001CP (plastic) • PC5001CP (plastic) • Compatible devices • Compatible devices • PC6010 - control panel • PC6010 - control panel • PC6442 - APS interface • PC6442 - APS interface • PC6443 - ODS interface • PC6443 - ODS interface LED Diagnostics Two LED’s located on the module light when activity is detected at the input of the associated channel. This activity is normally ‘data packets’ from the preceding repeater or control panel, but may indicate electrical noise if levels are significant. Refer to the troubleshooting guide below. Observed Activity Likely Cause LEDs are off most of the time LEDs appear to light simultaneously Normal Operation One LED appears to light periodically Electrical interference - May affect communications. One LED remains off Relocate wiring if possible. One LED lights continuously Electrical interference - Communications affected. One LED remains off Wiring must be relocated. Installation Refer to Figure 1 and Control Panel Installation Manual for wiring details. 1. Remove power from the system. 2. Locate cabinet not greater than 305m (1000ft) from the control panel or repeater. 3. Insert the three standoffs into the cabinet. Press firmly until standoffs click into place. 4. Align the module mounting holes over the standoffs. Press module firmly into place. 5. Route bus wire to the module in accordance with local requirements. 6. Insert required wiring into terminals and secure in place with a flatblade screwdriver. 7. Apply power to system and observe LED activity as indicated above. 8. Allow system to run for 15 minutes minimum. If a communication problem is present a ‘Back- bone Fault’ will be generated within the time period.

PC6311 Figure1 PC6311 Typical Configuration Interconnect Diagram NOTES Backbone devices may be connected in any combination but must not deviate from the following guidelines: *The longest communication path on the backbone between any two communicating devices must not exceed 1220m (4000ft). The maximum distance between two series-connected communicating devices must not exceed 305m (1000ft). The communication path must not have more than three PC6311 repeaters in a series. 305m (1000ft) max. between devices PC6311 Extended Range (Termination) 900m max. NC 800m max. NC 120Ω PC6010 PC6311 Interconnections must be wired using 0.6439mm (22AWG) copper wire. Capacitance must not exceed 50nF/305m. DO NOT use shielded wire. 305m (1000ft) max. 305m (1000ft) max. between devices between devices *PC6010PC6311 PC6311 PC6311 1220m (4000ft) maximum between any two communicating devices PC6442 305m (1000ft) maximum between devices *PC6443 PC6010 PC6311 PC6010 PC6311 PC6442 PC6311 120Ω 120Ω 120Ω For installations where a great distance is required between two devices,120Ω (1/4W, 5%) terminating resistors can be connected between the YEL and GRN terminals of each device as shown above. Note: For each distance indicated above, no other device can be added to the backbone.


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply