DOMETIC DM-2912 (01) PDF MANUAL

Read and understand these instructions carefully before installing, using, servicing, or performing maintenance on this product. These instructions MUST stay with this product.

Read and follow all safety information and instructions to avoid possible injury or death.

Incorrect installation, operation, servicing, or maintaining of this product can lead to serious injury. Follow all instructions.

The installation MUST comply with all applicable local and national codes, including the latest edition of the following standards:

U.S.A. / CANADA

• UN 46.02, Directive EC 2003/97

This is the safety alert symbol. It is used to alert you to potential physical injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

A signal word identifies safety messages and property damage messages, indicating the degree or level of hazard seriousness.

WARNING indicates a hazardous situation that, if NOT avoided, could result in death or serious injury.

CAUTION indicates a hazardous situation that, if NOT avoided, could result in minor or moderate injury.

NOTICE is used to address practices NOT related to physical injury. Failure to obey NOTICE warnings could damage the product or property.

NOTICE: Failure to obey the following notices could damage product or property:

• It is recommended to NOT take vehicle through an automatic car wash with towing mirrors attached. Damage could result to vehicle mirrors.

(4) Mirror Clamp (pn DM-1960)

(2) Mirror Head (pn DM-2493)

(2) Slide Arm

(1) Storage Bag

• Phillips Screwdriver (#2)

The grand aero towing mirror will fit most vehicles. For grand aero towing mirror mounting purposes, the vehicle mirror must have a gap between the vehicle mirror and the vehicle mirror housing for the towing mirror clamps to mount to.

1. Using a #2 Phillips screwdriver, remove the truss head screw (4 mm x 28 mm) from the mirror head ball socket.

2. Slide the short end of the arm into the hole in the mirror head ball socket, aligning the cross hole in the arm with the screw hole in the mirror head ball socket. Select the desired arm position (right hand, left hand, etc.).

3. Assemble the screw to the mirror head ball socket and hand tighten with a #2 Phillips screwdriver, securing the mirror head to the arm.

4. Repeat steps (a) through (c) for the other mirror.

NOTE: To change from right hand to left hand, and left hand to right hand, rotate the arm in the ball socket 180°.

The grand aero towing mirror can be mounted above or below the vehicle mirror, whichever works best for your situation. On certain vehicles, it may only fit above or below the vehicle mirror.

1. Loosen thumb screws (“2” on thumb screw) and remove mirror clamps from the slide arm.

2. Loosen thumb screws (“1” on thumb screw).

3. Assemble (2) mirror clamps to the vehicle mirror, sliding the “foot” of the clamps between the vehicle mirror and the vehicle mirror housing. Slide clamps in as far as possible for maximum clamp contact.

4. Position the mirror clamps approximately 2″ to 4″ apart with the bar clamps in the outer hole position.

5. Tighten thumb screws (“1” on thumb screw) by hand, pressing the heel of the clamp against the vehicle mirror on both clamps.

NOTICE: Do NOT use tools to tighten thumb screws. Doing so could damage vehicle mirror housing.

NOTICE: Failure to obey the following instructions, by fitting the mirror with the clamps on the arm, may result in the loss of the mirror.

6. Select desired arm position altitude and angle and slide the arm into the clamps. The (2) bar clamps can be positioned up or down, therefore, the arm can be mounted in one of four positions, high, low, and for vehicles with tapered mirrors, it is possible to level the arm by positioning one bar clamp down and the other bar clamp up. NOTE: Rotate mirror so the longest edge is toward the vehicle, with the reflector outward.

7. Tighten thumb screws (“2” on thumb screw), securing mirror clamp position on slide arm.

8. Repeat steps (1) through (6) for the other mirror.

To make mirror adjustments, it is recommended that one person sit in the driver’s seat giving mirror adjustment directions while another person makes the mirror adjustments.

1. To remove towing mirrors from the vehicle, loosen thumb screws (“1” on thumb screw), allowing removal.

2. Place mirror assemblies in the storage bag.

1. Loosen thumb screws (“1” on thumb screw) and remove the mirror and components from the vehicle.

2. Unthread thumb screws (“1” on thumb screw) sufficiently to allow removal of the DM-1953 aero pad.

3. Pull the pad from the ball end of the thumb screw.

4. Assemble the replacement pad to the clamp, aligning the tab of the pad with the slot in the clamp housing and aligning the ball socket on top of the pad with the ball end of the thumb screw.

5. Press the pad onto the thumb screw.

NOTE: It may be helpful to tighten the thumb screw (“1” on thumb screw) until the ball end “snaps” into the ball socket of the pad.