Post questions, comments, reviews or page errors in the comment box below.
PDF Content Summary:
****** Page 1 ****** XDimpIex MINI CUBE AUS/NZ 08/51232/1 Issue 1
****** Page 2 ****** 330 205
****** Page 3 ****** IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE Important Safety Advice When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock and injury to persons, including the following: If the appliance is damaged, check with the supplier before installation and operation. Do not use outdoors. Do not use in the immediate surroundings of a bath, shower or swimming pool. Do not locate the heater immediately below a fixed socket outlet or connection box. Do not cover the heater. Do not place material or garments on thé heater, or obstruct the air circulation around the heater, for instance by curtains or furniture, as this could cause overheating and a fire risk. This appliance is not intended for use by children or other persons without assistance or supervision if their physical, sensory or mental capabilities prevent them from using it safely. Children should be supervised to ensure that they do not play with the appliance. Do not use this heater in series with a thermal control, a program controller, a timer or any other device that switches on the heat automatically, since a fire risk exists when the heater is accidentally covered or displaced. Ensure that furniture, curtains or other combustible material are positioned no closer than I metre from the heater. In the event of a fault unplug the heater. Unplug the heater when not required for long periods. Although this heater complies with safety standards, we do not recommend its use on deep pile carpets or on long hair type of rugs. The appliance must be positioned so that the plug is accessible. If the supply cord is damaged it must be replaced by the manufacturer or service agent or a similarly qualified person in order to avoid a hazard. Keep the supply cord away from the front of the heater. Warning: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility. General Unpack the heater carefully and retain lhe packaging for possible future use, in the event of moving or returning the fire to your supplier. These models are designed to be free standing and are normally positioned against a wall. The fire incorporates a flame effect, which can be used with or without heating, so that the comforting effect may be enjoyed at any time of the year Using the flame effect on its own only requires little electricity. A choice of 750W or 1500W heat output is provided by the fan heater, which is located at the bottom of the unit. Before connecting the heater check thal the supply voltage is the same as that statecl on the heater. Please note: Used in an environment where background noise is very low, it may be possible to hear a sound which is related to the operation ot the flame effect, This is normal and should not be a cause for concern. Electrical connection WARNING -THIS APPLIANCE MUST BE EARTHED. This heater must be used on an AC supply only and the voltage marked on the heater must correspond to lhe supply voltage, Before switching on, please read the safety warnings and operating instructions. Controls – see Fig. 2 Three switches provide a choice of heat settings. A switch is in the ON position when the side with the markings on (i.e. J, It or II) is pushed in. Switch 1 (I) Controls the electricity supply to the heater and flame effect. Note: This switch must be in lhe ON (l) position Ior heater to operate with or without heat. Switch 2 (l) Provides 750W heat output Switch 3 (II) Provides 1500W output with switch 2 Lamp Replacement – see Fig. 3, Fig. 4 and Fig. 5 The lamps are located behind the back panel. To gain access to lhe lamps, the screws indicated in Fig. 3 which secure the back panel. must be removed. Remove and slide out panel as indicated on Fig. 4. Remove the defective lamp by unscrewing it as shown in Fig. 5. Replace with a 60W E 14 SES Clear candle lamp. Take care not to over-tighten the lamp. Refit the back panel and secure with the screws. Thermal Safety Cut-out The built-in overheat cut-out switches off the appliance automatically in the event of a fault. Switch off the appliance or disconnect the mains plug from the socket After a short cooling down phase, the appliance is ready for use again. If the fault should occur again, see your local dealer. Maintenance WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE. Cleaning WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER. For general cleaning use a soft clean duster — never use abrasive cleaners, The glass viewing screen should be cleaned carefully with a soft cloth. DO NOT use proprietary glass cleaners. To remove any accumulation of dust or fluff the soft brush attachment of a vacuum cleaner should occasionally be used to clean the outlet grille of the fan heater. After Sales Service Please see the separate Warranty leaflet for details of your Warranty & after sales service including contact details. Should you require after sales service, please get in touch with the supplier through whom you purchased the appliance, or the contract number on your Warranty leaflet.
FREE ENGLISH PDF
USER GUIDE – USER MANUAL
OWNER GUIDE – OWNER MANUAL
REFERENCE GUIDE – REFERENCE MANUAL
INSTRUCTION GUIDE – INSTRUCTION MANUAL