Post questions, comments, reviews or page errors in the comment box below.
PDF Content Summary:
****** Page 1 ****** Dimplex Better solutions through innovation 08/53541/0 (AU/NZ) Iss 4 OCN11654 Owner’s Manual Model BLF3451-AU/ PRISM 34″ EN IMPORTANT SAFETY INFORMATION: Always read this manual first before attempting to install or use this fireplace. For your safety, always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage.
****** Page 2 ****** Table of Contents @Welcome & Congratulations. . IMPORTANT INSTRUCTIONS Q] Quick Reference Guide Fireplace Installation Site Selection Surface Installation In-wall Recessed Installation – 100mm Deep Flush Mounted Installation – 200mm Deep Front Glass Installation Operation Maintenance 3 .4 7 8 8 9 10 11 13 15 19 Always use a qualified technician or service agency to repair this fireplace. • NOTE: Procedures and tech- niques that are considered important enough to emphasize. CAUTION: Procedures and tech- niques which, if not carefully followed, will result in damage to the equip- ment. A WARNING: Procedures and techniques which, if not carefully followed, will expose the user to the risk of fire, serious injury, or death.
****** Page 3 ****** Welcome & Congratulations Thank you and congratulations for choosing to purchase an electric fireplace from Dimplex, the world leader in electric fireplaces. Please carefully read and save these instructions. CAUTION: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible electric shock, fire hazard and will void the warranty. Please record your model and serial numbers below for future reference: model and serial numbers can be found on the Model and Serial Number Label of your fireplace. Serial Number Label NO NEED TO RETURN l’ TO THE STORE Questions With the Assembly? Require Parts Information? Product Under Manufacturer’s Warranty? call 1300 556 816 Please have your model number and product serial number ready. (See below) Rating Label with Model Number 3
****** Page 4 ****** IMPORTANT SAFETY INSTRUCTIONS Read all instructions before using this appliance. When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock and injury to persons, including the following: 1. If the appliance is damaged, check with the supplier before installation and operation. 2. Do not use outdoors. 3. Do not use in the immediate surroundings of a bath, shower or swimming pool. 4. Do not locate the appliance immediately below a fixed socket outlet or connection box. 5. This appliance can be used by children aged form 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by Children without supervision. 6. Children of less than 3 years should be kept away unless continuously supervised. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understanding the hazards involved. Children aged from 3 years and less than 8 years shall
****** Page 5 ****** A IMPORTANT SAFETY INSTRUCTIONS not plug in, regulate and clean the appliance or perform user maintenance. 7. Do not use this appliance in series with a thermal control, a program controller, a timer or any other device that switches on the heat automatically, since a fire risk exists when the appliance is accidentally covered or displaced. 8. Ensure that furniture, curtains or other combustible material are positioned no closer than 1 metre from the appliance. 9. In the event of a fault unplug the appliance. 10. Unplug the appliance when not required for long periods. 11 . Although this appliance complies with safety standards, we do not recommend its use on deep pile carpets or on long hair type of rugs. 12. The appliance must be positioned so that the plug is accessible. 13. If the supply cord is damaged it must be replaced by the manufacturer or service agent or a similarly qualified person in order to avoid a hazard. 14. Keep the supply cord away from the front of the appliance. A WARNING: In order to avoid overheating, do not cover the appliance. Do not place material or garments on the appliance, or obstruct the air circulation around the appliance, for instance by curtains or furniture, as this could cause overheating and a fire risk. 5
****** Page 6 ****** IMPORTANT SAFETY INSTRUCTIONS WARNING: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility. CAUTION: Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present. The heater carries the Warning Symbol indicating that it must not be covered SAVE THESE INSTRUCTIONS
****** Page 7 ****** Quick Reference Guide O The electrical information regarding your electric fireplace can be found on the rating label located on the front of the unit, behind the glass. Before installation, please record your fireplace’s serial number below for future reference. @ If you have any technical questions or concerns regarding the operation of your electric fireplace, or require service contact customer service. @ For dimensions of your fireplace, refer to Figure 1. Figure 1 6.8 in. (172 mm) 3.8 in. (95 mm 16.0 in. 18.0 in. (406 mm) (457 mm) 32.4 in. (823 mm) 30.0 in. (761 mm) (179 mm) 34.1 in. (867 mm) 19.4 in. (494 mm) 7
****** Page 8 ****** Site Selection Review and consider all of the following conditions for installation: • Dimensions of the unit: 870mm x 495mm • Unit requires a minimum of three (3) wall studs in order to ensure a secure installation Three possible installation methods: • Installation method: Surface mount; In-wall Recessed; or Flush mount • Hardwired or plug-in method WARNING: Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire, electric shock or injury to persons. Construction and electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electric shock and injury to persons. Select a location that is not susceptible to moisture and is away from drapes, furniture and high traffic. Fireplace Installation 1. 2. For ease of electrical hook up you may wish to locate the fireplace near an existing outlet (for plug-in convenience). ! NOTE 1: AIOAmp, 230- 240 Volt circuit is required. A dedicated circuit is preferred but not essential in all cases. A dedicated circuit will be required if, after installation, the circuit breaker trips or fuse blows on a regular basis when the heater is operating. Additional appliances on the same circuit may exceed the current rating of the circuit breaker. 3. Remove fireplace, front glass and hardware from box and remove all packaging materials before installation. 4. Store the fireplace in a safe, dry and dust free location until you are ready to install the fireplace.
****** Page 9 ****** Fireplace Installation The fireplace is packaged with a three prong plug installed for Figure 2 plug-in convenience. Hard wiring wall Mounting the fireplace is also an option by removing the plug from the factory fitted cord and completing the wiring according to National and Local Elecrical Codes. A WARNING: Do not attemptto wire your own new outlets or circuits. To reduce the risk of fire, electric shock or injury to persons, always use a licensed electrician. A WARNING: Ensure that the 3-Position Switch is set to the Off position (“O”) and that the circuit on which the fireplace is to be installed has the power cut off at the service panel until installation is complete. Surface Installation CAUTION: Two people will be required for various steps of this procedure. 1. Determine the mounting location of the unit so that the wall-mounting bracket can be installed into 3 wall studs. ! NOTE: It is recommended that the mounting bracket be installed 56 in. (1420mm) off of the ground to maintain an optimized viewing angle of the flame. Bracket Bottom Support Bracket 2. 3. 4. 5. Hold the wall mounting brack- et, with the bubble level on the top, on the wall so that the bubble on the level is centered between the two black lines. Mark the 4 mounting screw locations, on the wall, ensur- ing that the wall bracket stays level. (Figure 2) In locations where the screws are being installed only into drywall, install the supplied wall anchors before installing the screw (predrill if required). Secure the wall bracket to the wall using the supplied 11/2 in. (38mm) mounting screws and washers into the wall and/or wall anchors. 9
****** Page 10 ****** •X Fireplace Installation Figure 3 6. Install the bottom support bracket to the wall centered with the wall mounting bracket, using the appropriate mount- ing hardware, 13 %” (350mm) below the wall mounting brack- et. (Figure 2) 7. Remove the center screw from the bottom of the fireplace. (Figure 3) 8. Hang the fireplace from the bracket. 9. Install the removed screw through the bottom support bracket into the fireplace. 10.Refer to Front Glass Installa- tion section final installation procedures. In-wall Recessed Installation – 100mm Deep CAUTION: Two people may be required for various steps of this procedure. 1. Prepare a wall with a framed opening of 775mm wide x 420 mm high (Figure 4). ! NOTE: The sizing has allowed for 7mm around the fireplace insert for ease of installation. This fireplace does not require any additional venting. 2. Choose your method of supplying power to the unit: • Plug in (you may run the power cord out of the framed wall opening to an existing outlet or install an outlet on a nearby wall stud within the wall). • Hard wire the fireplace. ! NOTE: Hard wiring can be done by removing the plug from the factory fitted cord and completing the wiring according to National and Local Elecrical Codes. WARNING: Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric shock or injury to persons, always use a licensed electrician.
****** Page 11 ****** •X Fireplace Installation Ensure that the 3-Position Switch is set to the Off position (“O”) and that the circuit on which the fireplace is to be installed has the power cut off at the service panel until installation is complete. 3. 4. 5. 6. Lift fireplace and insert into opening (Figure 5). Use bubble level (supplied) to level the fireplace within the framing. Adjust as required. Drive four (4) supplied mounting screws through the four (4) mounting holes located in each comer of the fireplace chassis, into wall studs (Figure 6). Refer to Front Glass Installation section, for final installation procedures. Flush Mounted Installation – 200mm Deep CAUTION: Two people may be required for various steps of this procedure. 1. Prepare a wall with a framed opening of 837mm wide x 470 mm high (Figure 7). ! NOTE: The sizing has allowed for approx 7mm around the fireplace insert for ease of installation. This fireplace does not require any additional venting. Figure 4 11
****** Page 12 ****** •X Fireplace Installation Figure 6 Mounting hole the circuit on which the fireplace is to be installed has the power cut off at the service panel until installation is complete. 2. 3. 4. 5. Choose your method of supplying power to the unit: • Plug in (you may run the power cord out of the framed wall opening to an existing outlet or install an outlet on a nearby wall stud within the wall). • Hard wire the fireplace. Lift fireplace and insert into opening. The fireplace’s mounting trim should be flush against the wall (Figure 8). Use bubble level (supplied) to level the fireplace within the framing. Adjust as required. Drive four (4) supplied mounting screws through the four (4) mounting holes located on the inside surface of the fireplace chassis, into wall studs (Figure 8). ! NOTE: Hard wiring can be done by removing the plug from the factory fitted cord and completing the wiring according to National and Local Elecrical Codes. A WARNING: Do attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric shock or injury to persons, always use a licensed electrician. Ensure that the 3-Position Switch is set to the Off position (“O”) and that Figure 7
****** Page 13 ****** •X Fireplace Installation 6. Refer to Front Glass Installation section, for final installation procedures. Front Glass Installation Figure 8 Wall surface Mounting hole 1. 2. 3. 4. 5. Evenly distribute supplied glass rock on the front tray of the fireplace (Figure 9). Carefully mount front glass assembly so that the front glass hooks (4) hang on the front glass mounts on the fireplace (4) (Figure 9). Use the supplied two (2) Phillips sheet metal screws to Mounting hole fasten the glass assembly tabs to the fireplace (Figure 11). Ensure the fireplace’s 3-Position Switch is switched to the Off position (“O”). If unit is not hard-wired, plug fireplace into a 10 Amp, 230- 240 Volt outlet.(refer to NOTE 1). 13
****** Page 14 ****** •X Fireplace Installation Figure 9 Front glass assembly Hooks (4) Mounts (4) Front tray Figure 10 Tab
****** Page 15 ****** Operation Figure 11 A Figure 12 c D Floating DisplayTM c!) c A WARNING: This electricfirebox must be properly installed before it is used. The unit can be controlled by either the manual controls which are located on the upper right of the fireplace or the remote (Figure 11 & 12). The fireplace is supplied with an IR multifunction remote control. ! NOTE: To operate correctly, the remote control must be pointed towards the Floating DisplayTM. A. O Standby Turns the unit On and Off. -+ Activated by pressing the Standby button on the remote or the unit. • The unit will turn on with the same functions that it was set to when it was turned Off and the intake temperature will be indicated on the Floating DisplayTM. ! NOTE: When any button is pressed the intake temperature will be displayed on the Floating DisplayTM for 5 seconds. B. — Flame Effects Turns the flame effect On and Off. —i Activated by pressing the button on the remote. C. Heat ON/OFF Turns the heater On and Off. —Y Activated by pressing the button on the unit or the remote. 15
****** Page 16 ****** Operation • Indicated by the icon and the intake temperature being displayed on the Floating DisplayTM for 5 seconds before turning off. ! NOTE: After the heater is switched off, there is a 60 second fan delay, where the fan will continue running before turning off. ! NOTE: The unit can be operated in Heat Only Mode. When the unit is only running with the heater, the icon will continuously be displayed on the Floating DisplayTM. ! NOTE: The heater may emit a slight, harmless odor when first used. This odor is a normal condition caused by initial heating of internal heater parts and will not occur again. D & E. Thermostat Controls Adjusts the temperature set point to your individual requirements. Once the desired set temperature is reached the heater will turn off. The heater will cycle on and off to maintain the desired set temperature. The default temperature setting is 720F (220C). n Adjusted by pressing the to decrease the setpoint and the to increase the setpoint on the unit or the remote. • The Floating DisplayTM will indicate the temperature setpoint as it is adjusted. ! NOTE: Holding the +8 and 8- the buttons down for two seconds, on the unit, will change the temperature from oc to OF, or vice versa. Disable Heat If desired, depending on the season, the heater on the unit can be disabled. The unit will operate in the same fashion, with remainder of the controls. Pressing the and buttons on the unit at the same time and holding for 2 seconds will disable and enable the heater. ! NOTE: When the heater has 8- been disabled and either the or the is pressed the Floating DisplayTM will indicate ‘ F. g Color Themes Different presets of ambient lighting color combinations contained in the unit.
****** Page 17 ****** Operation -+ Changed by repeatedly pressing the corresponding button on the remote or the unit. Cycles through the different preset ambient lighting settings of the unit, this includes different combinations of colours of the flame base and media lighting. ! NOTE: The last theme of the cycle is a prism where the unit cycles through a variety of colours. Pressing the * button stops the cycling and holds the unit on the preferred color, indicated by a “U” – Unfreeze or a “F” – Freeze on the display. G. * Brightness Changes the brightness of the lights in the unit. —Adjusted by repeatedly pressing the corresponding button on the remote. • Indicated by the second digit on the Floating Display TM changing to show: “H” (high), and “L” (low). H. X Sleep Timer The Sleep Timer can be set to automatically shut off the fireplace after a preset time (from 30 minutes to 8 hours). -+ To set the timer press the timer button on the remote, repeatedly, until the desired time is displayed. • The Floating DisplayTM will display the different times as it is adjusted. Once the timer has begun, pressing the button will display the time remaining before the unit turns Off. ! NOTE: The Sleep Timer can be cancelled at any time by pressing the button repeatedly until the sleep timer displays nothing. Resetting the Temperature Cutoff Switch Should the heater overheat, an automatic cut out will turn the whole unit off and it will not come back on without being reset. It can be reset by turning the unit off at the main disconnect panel and waiting 5 minutes before turning the unit back on. 17
****** Page 18 ****** Operation Remote Control Battery Replacement To replace the battery: 1. Slide battery cover open on the remote control. 2. Correctly install one 3 Volt (CR2032 [longer life] or CR2025) battery in the battery holder. 3. Close the battery cover. Battery must be recycled or disposed of properly. Check with your Local Authority or Retailer for recycling advice in your area
****** Page 19 ****** / Maintenance A WARNING: Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electric shock or damage to persons. Partially Reflective Glass Cleaning The partially reflective glass is cleaned in the factory during the assembly operation. During shipment, installation, handling, etc., the partially reflective glass may collect dust particles; these can be removed by dusting lightly with a clean dry cloth. To remove fingerprints or other marks, the partially reflective glass can be cleaned with a damp cloth. The partially reflective glass should be completely dried with a lint free cloth to prevent water spots. To prevent scratching, do not use abrasive cleaners. Contact Details Glen Dimplex Australia Pty Ltd 8 Lakeview Drive, Scoresby, VIC 3179 Australia Fireplace Surface Cleaning Use only a damp cloth to clean painted surfaces of the fireplace. Do not use abrasive cleaners. Servicing Except for installation and cleaning described in this manual, an authorized service representative should perform any other servicing. Glen Dimplex Australaasia Ltd 38 Harris Road East Tamaki, Auckland 2013 New Zealand Phone: Email: Web: 1300 556 816 email@example.com dimplex.com.au Email: Web: +61 09 274 8265 firstname.lastname@example.org dimplex.co.nz 19
FREE ENGLISH PDF
USER GUIDE – USER MANUAL
OWNER GUIDE – OWNER MANUAL
REFERENCE GUIDE – REFERENCE MANUAL
INSTRUCTION GUIDE – INSTRUCTION MANUAL