DELL LATITUDE E6320 (01) PDF MANUAL


Post questions, comments, reviews or errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD DELL LATITUDE E6320 (01) PDF MANUAL


PDF Content Summary: Dell Latitude E6320 Owner's Manual Regulatory Model P12S Regulatory Type P12S001 Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Information in this publication is subject to change without notice. © 2011 Dell Inc. All rights reserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: DellTM, the DELL logo, Dell PrecisionTM, Precision ONTM,ExpressChargeTM, LatitudeTM, Latitude ONTM, OptiPlexTM, VostroTM, and Wi-Fi CatcherTM are trademarks of Dell Inc. Intel®, Pentium®, Xeon®, CoreTM, AtomTM, Centrino®, and Celeron® are registered trademarks or trademarks of Intel Corporation in the U.S. and other countries. AMD® is a registered trademark and AMD OpteronTM, AMD PhenomTM, AMD SempronTM, AMD AthlonTM, ATI RadeonTM, and ATI FireProTM are trademarks of Advanced Micro Devices, Inc. Microsoft®, Windows®, MS-DOS®, Windows Vista®, the Windows Vista start button, and Office Outlook® are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. Blu-ray DiscTM is a trademark owned by the Blu-ray Disc Association (BDA) and licensed for use on discs and players. The Bluetooth® word mark is a registered trademark and owned by the Bluetooth® SIG, Inc. and any use of such mark by Dell Inc. is under license. Wi-Fi® is a registered trademark of Wireless Ethernet Compatibility Alliance, Inc. Other trademarks and trade names may be used in this publication to refer to either the entities claiming the marks and names or their products, Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own. 2011 – 07 Rev. A00 Contents Notes, Cautions, and Warnings..................................................................2 1 Working on Your Computer......................................................................9 Before Working Inside Your Computer.............................................................................9 Recommended Tools.......................................................................................................10 Turning Off Your Computer..............................................................................................11 After Working Inside Your Computer..............................................................................11 2 ExpressCard..............................................................................................13 Removing The ExpressCard............................................................................................13 Installing the ExpressCard..............................................................................................13 3 Secure Digital (SD) Card.........................................................................15 Removing The Secure Digital (SD) Card.........................................................................15 Installing the Secure Digital (SD) Card............................................................................15 4 Battery........................................................................................................17 Removing The Battery.....................................................................................................17 Installing The Battery......................................................................................................17 5 Subscriber Identity Module (SIM) Card...............................................19 Removing The Subscriber Identity Module (SIM) Card..................................................19 Installing the Subscriber Identity Module (SIM) Card....................................................20 6 Hard Drive..................................................................................................21 Removing The Hard Drive................................................................................................21 Installing The Hard Drive.................................................................................................22 7 Optical Drive..............................................................................................23 Removing The Optical Drive............................................................................................23 Installing The Optical Drive.............................................................................................25 8 Base Cover................................................................................................27 Removing The Base Cover..............................................................................................27 Installing The Base Cover...............................................................................................28 9 Memory Card............................................................................................29 Removing The Memory...................................................................................................29 Installing The Memory.....................................................................................................30 10 Coin-Cell Battery....................................................................................31 Removing The Coin-Cell Battery.....................................................................................31 Installing The Coin-Cell Battery.......................................................................................32 11 Wireless Local Area Network (WLAN) Card.....................................33 Removing The Wireless Local Area Network (WLAN) Card...........................................33 Installing The Wireless Local Area Network (WLAN) Card............................................34 12 Wireless Wide Area Network (WWAN) Card...................................35 Removing The Wireless Wide Area Network (WWAN) Card.........................................35 Installing The Wireless Wide Area Network (WWAN) Card..........................................36 13 Keyboard Trim.........................................................................................37 Removing The Keyboard Trim.........................................................................................37 Installing The Keyboard Trim..........................................................................................38 14 Keyboard..................................................................................................39 Removing The Keyboard.................................................................................................39 Installing The Keyboard..................................................................................................41 15 Palm Rest.................................................................................................43 Removing The Palmrest Assembly..................................................................................43 Installing The Palmrest Assembly...................................................................................45 16 Bluetooth Card........................................................................................47 Removing The Bluetooth Card.........................................................................................47 Installing The Bluetooth Card..........................................................................................48 17 LED Board................................................................................................49 Removing The LED Board................................................................................................49 Installing The LED Board.................................................................................................51 18 Smart Card Reader.................................................................................53 Removing The Smart Card Reader..................................................................................53 Installing The Smart Card Reader...................................................................................55 19 Media Board...........................................................................................57 Removing The Media Board............................................................................................57 Installing The Media Board.............................................................................................59 20 Display Hinges........................................................................................61 Removing The Display Hinge Covers..............................................................................61 Installing The Display Hinge Covers................................................................................62 21 Display Assembly...................................................................................63 Removing The Display Assembly....................................................................................63 Installing The Display Assembly.....................................................................................67 22 System Board..........................................................................................69 Removing The System Board..........................................................................................69 Installing The System Board...........................................................................................72 23 Heat Sink..................................................................................................75 Removing The Heat-Sink Assembly................................................................................75 Installing The Heat-Sink Assembly.................................................................................77 24 Input/Output Panel.................................................................................79 Removing The Input/Output Panel..................................................................................79 Installing The Input/Output Panel....................................................................................81 25 Speaker....................................................................................................83 Removing The Speakers..................................................................................................83 Installing The Speakers...................................................................................................85 26 DC-In Port................................................................................................87 Removing The DC-In Port................................................................................................87 Installing The DC-In Port.................................................................................................89 27 Display Bezel...........................................................................................91 Removing The Display Bezel...........................................................................................91 Installing The Display Bezel............................................................................................92 28 Display Panel..........................................................................................93 Removing The Display Panel...........................................................................................93 Installing The Display Panel............................................................................................94 29 Camera.....................................................................................................95 Removing The Camera....................................................................................................95 Installing The Camera.....................................................................................................96 30 Specifications.........................................................................................97 Technical Specifications.................................................................................................97 31 System Setup........................................................................................103 Overview.......................................................................................................................103 Entering System Setup..................................................................................................103 System Setup Menu Options.........................................................................................103 32 Diagnostics............................................................................................115 Device Status Lights......................................................................................................115 Battery Status Lights.....................................................................................................115 LED Error Codes............................................................................................................115 33 Contacting Dell.....................................................................................117 Contacting Dell..............................................................................................................117 8 Working on Your Computer 1 Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have performed the steps in Working on Your Computer. • You have read the safety information that shipped with your computer. • A component can be replaced or--if purchased separately--installed by performing the removal procedure in reverse order. WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at http://www.dell.com/regulatory_compliance. CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface, such as a connector on the back of the computer. CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins. CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and aligned. 9 NOTE: The color of your computer and certain components may appear differently than shown in this document. To avoid damaging your computer, perform the following steps before you begin working inside the computer. 1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched. 2. Turn off your computer (see Turning Off Your Computer). 3. If the computer is connected to a docking device (docked) such as the optional Media Base or Battery Slice, undock it. CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device. 4. Disconnect all network cables from the computer. 5. Disconnect your computer and all attached devices from their electrical outlets. 6. Close the display and turn the computer upside-down on a flat work surface. NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer. 7. Remove the main battery. 8. Turn the computer top-side up. 9. Open the display. 10. Press the power button to ground the system board. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the display. CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components. 11. Remove any installed ExpressCards or Smart Cards from the appropriate slots. Recommended Tools The procedures in this document may require the following tools: • Small flat-blade screwdriver 10 • #0 Phillips screwdriver • #1 Phillips screwdriver • Small plastic scribe • Flash BIOS update program CD Turning Off Your Computer CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer. 1. Shut down the operating system: • In Windows Vista : Click Start • In Windows XP: Click Start → Turn Off Computer → Turn Off . The computer turns off after the operating system shutdown process is complete. 2. Ensure that the computer and all attached devices are turned off. If your computer and attached devices did not automatically turn off when you shut down your operating system, press and hold the power button for about 4 seconds to turn them off. After Working Inside Your Computer After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on your computer. CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries designed for other Dell computers. 1. Connect any external devices, such as a port replicator, battery slice, or media base, and replace any cards, such as an ExpressCard. 2. Connect any telephone or network cables to your computer. 11 , then click the arrow in the lower-right corner of the Start menu as shown below, and then click Shut Down. CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the computer. 3. Replace the battery. 4. Connect your computer and all attached devices to their electrical outlets. 5. Turn on your computer. 12 ExpressCard 2 Removing The ExpressCard 1. Follow the procedures in Before Working On Your Computer. 2. Press in on the ExpressCard to release it from the computer. 3. Slide the ExpressCard out of the computer. Installing the ExpressCard 1. Slide the ExpressCard into its slot until it clicks into place. 2. Follow the procedures in After working inside your computer. 13 14 Secure Digital (SD) Card 3 Removing The Secure Digital (SD) Card 1. Follow the procedures in Before Working On Your Computer. 2. Press in on the SD card to release it from the computer. 3. Slide the SD card out of the computer. Installing the Secure Digital (SD) Card 1. Slide the Secure Digital (SD) card into its slot until it clicks into place. 2. Follow the procedures in After working inside your computer. 15 16 Battery 4 Removing The Battery 1. Follow the procedures in Before Working On Your Computer. 2. Slide the battery latches to unlock the battery. 3. Slide the battery out and remove it from the computer. Installing The Battery 1. Slide the battery into its slot until it clicks into place. 2. Follow the procedures in After working inside your computer. 17 18 Subscriber Identity Module (SIM) Card 5 Removing The Subscriber Identity Module (SIM) Card 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Press in on the SIM card to release it from the computer. 4. Slide the SIM card out from the computer. 19 Installing the Subscriber Identity Module (SIM) Card 1. Slide the SIM card into its compartment. 2. Install the battery. 3. Follow the procedures in After Working Inside Your Computer. 20 Hard Drive 6 Removing The Hard Drive 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the screws that secure the hard drive to the computer. 4. Slide and remove the hard drive out of the computer. 5. Remove the screw that secures the hard-drive caddy to the hard drive. 21 6. Pull and remove the hard-drive caddy away from the hard drive. Installing The Hard Drive 1. Attach the hard-drive caddy to the hard drive. 2. Tighten the screws to secure the hard-drive caddy to the hard drive. 3. Slide the hard drive into the computer. 4. Replace and tighten the screws that secure the hard drive to the computer. 5. Install the battery. 6. Follow the procedures in After working inside your computer. 22 Optical Drive 7 Removing The Optical Drive 1. Follow the procedures in Before Working On Your Computer. 2. Press and release the optical drive latch. 3. Pull the optical drive out of the computer. 4. Pull the optical drive door from one side to release it. 5. Pull the other side of the optical drive door to release it completely from the optical drive. 23 6. Remove the screw that secures the drive latch to the optical drive. 7. Remove the drive latch from the optical drive. 8. Remove the screws that secures the drive latch bracket to the optical drive. 24 9. Remove the drive latch bracket from the optical drive. Installing The Optical Drive 1. Insert the drive latch bracket into the optical drive. 2. Tighten the screws to secure the drive latch bracket to the optical drive. 3. Insert the drive latch into the optical drive. 4. Tighten the screw to secure the drive latch to the optical drive. 5. Push the optical drive door to insert it completely into the optical drive. 6. Push the optical drive door from the other side till it clicks into place. 7. Insert the optical drive using the drive latch. 8. Push the drive latch in to secure it into its slot. 9. Follow the procedures in After working inside your computer. 25 26 Base Cover 8 Removing The Base Cover 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) Card. 4. Remove the screws that secure the base cover to the computer. 5. Lift the base cover up and away from the computer. 27 Installing The Base Cover 1. Place the base cover to align the screw holes correctly with the computer. 2. Replace and tighten the screws to secure the base cover to the computer. 3. Install the Secure Digital (SD) Card. 4. Follow the procedures in After Working Inside Your Computer. 28 Memory Card 9 Removing The Memory 1. Follow the procedures in Before Working On Your Computer 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the base cover. 5. Pry the retention clips away from the memory module until it pops up. 6. Remove the memory module from the computer. 29 Installing The Memory 1. Insert the memory module into the memory slot. 2. Press the clips to secure the memory module to the system board. 3. Install the base cover. 4. Install the Secure Digital (SD) card. 5. Install the battery 6. Follow the procedures in After Working Inside Your Computer. 30 Coin-Cell Battery 10 Removing The Coin-Cell Battery 1. Follow the procedures in Before Working on Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the base cover. 5. Disconnect the coin-cell battery cable from the system board. 6. Release and remove the coin-cell battery from the computer. 31 Installing The Coin-Cell Battery 1. Place the coin-cell battery in its location. 2. Connect the coin-cell battery cable to the system board. 3. Install the base cover. 4. Install the Secure Digital (SD) card. 5. Install the battery 6. Follow the procedures in After working inside your computer. 32 Wireless Local Area Network (WLAN) Card 11 Removing The Wireless Local Area Network (WLAN) Card 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the base cover. 5. Disconnect the antenna cables from the WLAN card. 6. Remove the screw that secures the WLAN card to the computer. 7. Remove the WLAN card from its slot on the system board. 33 Installing The Wireless Local Area Network (WLAN) Card 1. Insert the WLAN card into its connector at a 45–degree angle. 2. Replace and tighten the screw that secures the WLAN card to the computer. 3. Connect the antenna cables according to the color code on the WLAN card. 4. Install the base cover. 5. Install the Secure Digital (SD) card. 6. Install the battery 7. Follow the procedures in After Working Inside Your Computer. 34 Wireless Wide Area Network (WWAN) Card 12 Removing The Wireless Wide Area Network (WWAN) Card 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the base cover. 5. Disconnect the antenna cables from the WWAN card. 6. Remove the screw that secures the WWAN card to the computer. 7. Remove the WWAN card from the computer. 35 Installing The Wireless Wide Area Network (WWAN) Card 1. Insert the WWAN card into its connector at a 45–degree angle. 2. Replace and tighten the screw to secure the WWAN card to the computer. 3. Connect the antenna cables according to the color code on the WLAN card. 4. Install the base cover. 5. Install the Secure Digital (SD) card. 6. Install the battery 7. Follow the procedures in After Working Inside Your Computer. 36 Keyboard Trim 13 Removing The Keyboard Trim 1. Follow the procedures in Before Working On Your Computer. 2. Using a plastic scribe, pry under the keyboard trim to release it from the computer. 3. Lift the keyboard trim to release the tabs and remove it from the computer. 37 Installing The Keyboard Trim 1. Align the keyboard trim with the keyboard and snap it into place. 2. Follow the procedures in After Working Inside Your Computer. 38 Keyboard 14 Removing The Keyboard 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the keyboard trim. 4. Remove the screws that secure the keyboard to the computer. 5. Remove the screws that secure the keyboard to the palmrest assembly. 6. Flip the keyboard over and lay it toward the display. 39 7. Lift the clip to release the keyboard cable and disconnect it from the computer. 8. Remove the keyboard from the computer. 40 9. Remove the tape securing the keyboard cable from the keyboard. 10. Disconnect and remove the keyboard cable from the keyboard. Installing The Keyboard 1. Connect the keyboard cable and secure it to the keyboard using the tape. 2. Connect the keyboard cable to its connector on the system board. 3. Turn the keyboard over and lay it on the palmrest. 4. Replace and tighten the screws to secure the keyboard to the palmrest assembly. 5. Replace and tighten the screws to secure the keyboard to the computer. 6. Install the battery. 7. Install the keyboard trim 8. Follow the procedures in After Working Inside Your Computer. 41 42 Palm Rest 15 Removing The Palmrest Assembly 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the base cover. 6. Remove the ExpressCard. 7. Remove the hard drive. 8. Remove the keyboard trim. 9. Remove the keyboard. 10. Remove the screws that secure the palmrest assembly to the computer. 11. Flip the computer and disconnect the following cables from the system board: • LED board • touchpad • bluetooth • contactless smart card reader • ExpressCard • fingerprint reader 43 12. Remove the screws to release the palmrest assembly from the system board. 13. Lift the palmrest assembly along the edges to unlock the tabs and remove it away from the computer. 44 Installing The Palmrest Assembly 1. Align the palmrest assembly with the computer and snap it into place. 2. Replace and tighten the screws to secure the palmrest assembly to the system board. 3. Connect the following cables to the system board: • LED board • touchpad • bluetooth • contactless smart card reader • Express Card • fingerprint reader 4. Replace and tighten the screws to secure the palmrest assembly to the computer. 5. Install the keyboard. 6. Install the keyboard trim. 7. Install the hard drive. 8. Install the ExpressCard. 9. Install the base cover. 10. Install the optical drive. 11. Install the Secure Digital (SD) card. 12. Install the battery. 13. Follow the procedures in After Working Inside Your Computer. 45 46 Bluetooth Card 16 Removing The Bluetooth Card 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the base cover. 6. Remove the ExpressCard. 7. Remove the hard drive. 8. Remove the keyboard trim. 9. Remove the keyboard. 10. Remove the palmrest assembly. 11. Remove the screws that secure the bluetooth card to the palmrest assembly. 12. Remove the bluetooth card from the palmrest assembly. 47 13. Release and remove the bluetooth cable from the bluetooth card. Installing The Bluetooth Card 1. Connect the bluetooth cable to the bluetooth card. 2. Place the bluetooth card on the palmrest assembly. 3. Replace and tighten the screw to secure the bluetooth card to the palmrest assembly. 4. Install the palmrest assembly. 5. Install the keyboard. 6. Install the keyboard trim. 7. Install the hard drive. 8. Install the ExpressCard. 9. Install the base cover. 10. Install the optical drive. 11. Install the Secure Digital (SD) card. 12. Install the battery. 13. Follow the procedures in After Working Inside Your Computer. 48 LED Board 17 Removing The LED Board 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the base cover. 6. Remove the ExpressCard. 7. Remove the hard drive. 8. Remove the keyboard trim. 9. Remove the keyboard. 10. Remove the palmrest assembly. 11. Release the LED board cable from the routing channel. 12. Remove the screw that secures the LED board to the palm rest assembly. 49 13. Remove the LED board from the palm rest assembly. 50 Installing The LED Board 1. Align the LED board on the palmrest. 2. Replace and tighten the screw that secure the LED board to the palmrest. 3. Route the LED board cable to its original position. 4. Install the palmrest assembly. 5. Install the keyboard. 6. Install the keyboard trim. 7. Install the hard drive. 8. Install the ExpressCard. 9. Install the base cover. 10. Install the optical drive. 11. Install the Secure Digital (SD) card. 12. Install the battery. 13. Follow the procedures in After Working Inside Your Computer. 51 52 Smart Card Reader 18 Removing The Smart Card Reader 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the base cover. 6. Remove the ExpressCard. 7. Remove the hard drive. 8. Remove the keyboard trim. 9. Remove the keyboard. 10. Remove the palmrest assembly 11. Disconnect the smart card reader cable from the system board. 12. Remove the screws that secure the smart card reader to the computer. 53 13. Lift and remove the smart card reader from the computer. 54 Installing The Smart Card Reader 1. Place the smart card reader to its original position on the computer. 2. Replace and tighten the screws to secure the smart card reader to the computer. 3. Connect the smart card reader cable to the system board. 4. Replace and tighten the screws to secure the palmrest assembly to the computer. 5. Install the palmrest assembly. 6. Install the keyboard. 7. Install the keyboard trim. 8. Install the hard drive. 9. Install the ExpressCard. 10. Install the base cover. 11. Install the optical drive. 12. Install the Secure Digital (SD) card. 13. Install the battery. 14. Follow the procedures in After Working Inside Your Computer. 55 56 Media Board 19 Removing The Media Board 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the base cover. 6. Remove the ExpressCard. 7. Remove the hard drive. 8. Remove the keyboard trim. 9. Remove the keyboard. 10. Remove the palmrest assembly. 11. Disconnect the media board cable from the system board. 12. Remove the screws that secures the media board to the computer. 57 13. Remove the media board from the computer. 58 Installing The Media Board 1. Align the media board to its original position on the computer. 2. Replace and tighten the screws to secure the media board to the computer. 3. Connect the media board cable to the system board. 4. Install the palmrest assembly. 5. Install the keyboard. 6. Install the keyboard trim. 7. Install the hard drive. 8. Install the ExpressCard. 9. Install the base cover. 10. Install the optical drive. 11. Install the Secure Digital (SD) card. 12. Install the battery. 13. Follow the procedures in After Working Inside Your Computer. 59 60 Display Hinges 20 Removing The Display Hinge Covers 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the base cover. 6. Remove the ExpressCard. 7. Remove the hard drive. 8. Remove the keyboard trim. 9. Remove the keyboard. 10. Remove the palmrest assembly. 11. Remove the screws that secure the display hinge covers to the computer. 12. Remove the display hinge covers from the computer. 61 Installing The Display Hinge Covers 1. Place the display hinges in the appropriate positions. 2. Replace and tighten the screws to secure the display hinge covers to the computer. 3. Install the palmrest assembly. 4. Install the keyboard. 5. Install the keyboard trim. 6. Install the hard drive. 7. Install the ExpressCard. 8. Install the base cover. 9. Install the optical drive. 10. Install the Secure Digital (SD) card. 11. Install the battery. 12. Follow the procedures in After Working Inside Your Computer. 62 Display Assembly 21 Removing The Display Assembly 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the base cover. 6. Remove the ExpressCard. 7. Remove the hard drive. 8. Remove the keyboard trim. 9. Remove the keyboard. 10. Remove the palmrest assembly. 11. Remove the display hinge covers. 12. Release the antenna cables from the computer. 13. Remove the screws that secure the display assembly to the computer. 63 14. Pull out the antenna cables from their routing channels? 15. Remove the screws that secure the display cable bracket to the system board. 64 16. Remove the display cable bracket from the computer. 17. Pull the display cable to disconnect it from the system board. 18. Remove the screw that secures the display assembly to the computer. 65 19. Remove the display assembly from the computer. 66 Installing The Display Assembly 1. Align the display assembly into its original position on the computer. 2. Replace and tighten the screw to secure the display assembly to the computer. 3. Replace and connect the display cable to the system board. 4. Align the display cable bracket to its original position. 5. Replace and tighten the screws to secure the display cable bracket to the system board. 6. Route the antenna cables through the system board. 7. Replace and tighten the screws to secure the display panel to the computer. 8. Route the antenna cables to their original position. 9. Install the display hinge covers. 10. Install the palmrest assembly. 11. Install the keyboard. 12. Install the keyboard trim. 13. Install the hard drive. 14. Install the ExpressCard. 15. Install the base cover. 16. Install the optical drive. 17. Install the Secure Digital (SD) card. 18. Install the battery. 19. Follow the procedures in After Working Inside Your Computer. 67 68 System Board 22 Removing The System Board 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the subscriber identity module (SIM) card. 6. Remove the base cover. 7. Remove the ExpressCard. 8. Remove the hard drive. 9. Remove the keyboard trim. 10. Remove the keyboard. 11. Remove the wireless local area network (WLAN) card. 12. Remove the wireless wide area network (WWAN) card. 13. Remove the coin-cell battery. 14. Remove the media board. 15. Remove the palmrest assembly. 16. Remove the display hinge covers. 17. Remove the display assembly. 18. Disconnect and release the smart card and the speaker cables from the system board. 69 19. Remove the screws that secure the system board to the computer. 20. Lift the system board to locate the power supply cable. 21. Disconnect the power supply cable from the system board. 70 22. Lift and remove the system board from the computer. NOTE: Steps 23 and 24 are applicable for computers that shipped in the United States of America. 23. Flip the system over and remove the screw that secures the TAA board. 71 24. Remove the TAA board from the system. Installing The System Board 1. Place the TAA board to its original position. 72 NOTE: Steps 1 and 2 are applicable for computers that shipped in the United States of America. 2. Replace and tighten the screw to secure the TAA board to the computer. 3. Align the system board into its original position on the computer. 4. Connect the power supply cable. 5. Replace and tighten the screws to secure the system board to the computer. 6. Route and connect the smart card and speaker cables to the system board. 7. Install the display assembly. 8. Install the display hinge covers. 9. Install the palmrest assembly. 10. Install the keyboard. 11. Install the keyboard trim. 12. Install the hard drive. 13. Install the ExpressCard. 14. Install the base cover. 15. Install the optical drive. 16. Install the Secure Digital (SD) card. 17. Install the battery. 18. Follow the procedures in After Working Inside Your Computer. 73 74 Heat Sink 23 Removing The Heat-Sink Assembly 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the subscriber identity module (SIM) card. 6. Remove the base cover. 7. Remove the ExpressCard. 8. Remove the hard drive. 9. Remove the keyboard trim. 10. Remove the keyboard. 11. Remove the wireless local area network (WLAN) card. 12. Remove the wireless wide area network (WWAN) card. 13. Remove the coin-cell battery. 14. Remove the media board. 15. Remove the palmrest assembly. 16. Remove the display hinge covers. 17. Remove the display assembly. 18. Remove the system board. 19. Disconnect the heat-sink cable from the system board. 75 20. Loosen the screws that secure the heat-sink assembly to the system board. 21. Remove the heat-sink assembly from the system board. 76 Installing The Heat-Sink Assembly 1. Align the heat-sink assembly to its original position on the system board. 2. Tighten the screws to secure the heat-sink assembly to the system board. 3. Connect the heat-sink cable to the system board. 4. Install the heat-sink assembly. 5. Install the display assembly. 6. Install the display hinge covers. 7. Install the palmrest assembly. 8. Install the keyboard. 9. Install the keyboard trim. 10. Install the hard drive. 11. Install the ExpressCard. 12. Install the base cover. 13. Install the optical drive. 14. Install the Secure Digital (SD) card. 15. Install the battery. 16. Follow the procedures in After Working Inside Your Computer. 77 78 Input/Output Panel 24 Removing The Input/Output Panel 1. Follow the procedures in Before Working On Your Computer. 2. Remove the battery. 3. Remove the Secure Digital (SD) card. 4. Remove the optical drive. 5. Remove the subscriber identity module (SIM) card. 6. Remove the base cover. 7. Remove the ExpressCard. 8. Remove the hard drive. 9. Remove the keyboard trim. 10. Remove the keyboard. 11. Remove the wireless local area network (WLAN) card. 12. Remove the wireless wide area network (WWAN) card. 13. Remove the coin-cell battery. 14. Remove the media board. 15. Remove the palmrest assembly. 16. Remove the display hinge covers. 17. Remove the display assembly. 18. Remove the screw that secures the I/O panel to the computer. 79 19. Remove the I/O panel from the computer. 80


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply