DELL 3200MP (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD DELL 3200MP (01) PDF MANUAL


PDF Content Summary: Dell™ 3200MP Projector User's Guide The information below is provided by the supplier of the referenced device without independent verification by Dell and is subject to the restrictions and disclaimers. Safety Instructions About Your Projector Installation Using Your Projector Troubleshooting Specifications Regulatory Notices Contacting Dell Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your projector. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death. Information in this document is subject to change without notice. ©2002 Coretronic Corporation. ©2002 Dell Computer Corporation. All rights reserved. Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden. Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Computer Corporation; DLP and Texas Instruments are trademarks of Texas Instruments Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation; Macintosh is a registered trademark of Apple Computer, Inc. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its own. Restrictions and Disclaimers The information contained in this document, including all instructions, cautions, and regulatory approvals and certifications, is based upon statements provided to Dell by the manufacturer and has not been independently verified or tested by Dell. Dell disclaims all liability in connection with any deficiencies in such information. All statements or claims regarding the properties, capabilities, speeds, or qualifications of the part referenced in this document are made by the manufacturer and not by Dell. Dell specifically disclaims any knowledge of the accuracy, completeness, or substantiation for any such statements. November 2002 Rev. A01 Back to Contents Page Safety Instructions: Dell™ 3200MP Projector CAUTION Use the following safety guidelines to help protect your projector from potential damage and to ensure your own personal safety: The lamp becomes very hot with use. Do not attempt to replace the lamp after use until the projector has been allowed to cool down for at least 30 minutes, and follow all instructions in "Changing the Lamp." Do not touch the bulb or the lamp glass at any time. The bulb may explode due to improper handling, including the touching of the bulb or the lamp glass. Remove lens cap before turning on projector. Failure to do so may cause the lens cap to reach high temperatures. To avoid damaging the projector and lamp, allow the cooling fan to run for 2 minutes before turning off the projector. The remote control is equipped with a Class II laser that emits laser radiation. To reduce the risk of injury, do not look directly into the laser light, and do not point the laser light into anyone's eyes. Do not block the ventilation slots and openings on the projector. Disconnect the power cord from the electrical outlet if the projector is not used for a long period of time. Do not use the projector in an extremely hot, cold, or humid environment. Do not use the projector in areas susceptible to excessive dust and dirt. Do not use the projector near any appliance that generates a strong magnetic field. Do not place the projector in direct sunlight. Do not look into the lens while the projector is on; the bright light may hurt your eyes. To reduce the risk of fire or electric shock, do not expose the projector to rain or moisture. To prevent electric shock, do not open or disassemble the projector further than what is needed for lamp replacement. To avoid damaging the projector, ensure that the zoom lens and elevator foot are fully retracted before moving the projector or placing the projector in its carrying case. Turn off the projector and disconnect it from the electrical outlet before cleaning it. Use a soft cloth moistened with mild detergent to clean the display housing. Do not use abrasive cleaners, waxes, or solvents. Back to Contents Page Back to Contents Page About Your Projector: Dell™ 3200MP Projector Features Equipment Main Unit Control Panel Connection Ports Remote Control With Mouse Function and Laser Pointer Features Single chip 0.7" Texas Instruments DLP™ technology High contrast, double data rate(DDR) digital micromirror device True XGA, 1024 x 768 addressable pixels 3.5 lb (1.6 kg) lightweight compact design 1300 ANSI lumens brightness(Max), 1200 ANSI lumens brightness (Average) Auto image re-sizing to 1024 x 768 full screen with scaling compression compatibility for UXGA, SXGA+, SXGA, XGA, SVGA, VGA, MAC State-of-the -art motion adaptive hardware deinterlacing with 3:2 and 2:2 pull down 150-watt, user-replaceable P-VIP lamp Compatibility with Macintosh® computers Compatibility with NTSC, NTSC4.43, PAL, PAL-M, PAL-N, SECAM, and HDTV (1080i, 720P, 576P, 480i/P) Remote control with mouse function and laser pointer M1-DA connection for digital and analog video connectivity. High-definition TV compatibility User-friendly, multi-language on-screen display (OSD) Advanced electronic keystone correction User-friendly control panel with backlight Carrying case included Equipment Your projector comes with all the items shown below. Ensure that you have all the items, and contact Dell if anything is missing. Main unit Power cord M1-A to VGA cable S-video cable RCA audio cable Composite video cable

M1-A signal cable for HDTV/component Mini pin to mini pin cable Batteries (2)

Remote control with mouse function and laser pointer Dell 3200MP Projector Safety and Dell 3200MP Projector User's Guide Dell 3200MP Projector Quick Start Card

Warranty Guide Owner's Manual Carrying case Main Unit 1 Control panel 2 Zoom ring 3 Focus ring 4 Zoom lens 5 Remote control receiver 6 Elevator button Control Panel 1 Power button 2 Four directional keys 3 Keystone adjustment 4 Temperature warning light 5 Lamp warning light 6 Re-sync 7 Menu 8 Keystone adjustment 9 Source Connection Ports 1 VGA Out (monitor loop-through) 2 Composite video connector 3 Audio input connector 4 S-video connector 5 Computer input and HDTV/ component video connector with remote mouse Remote Control With Mouse Function and Laser Pointer 1 Light 2 Power button 3 PU button (page up) 4 Laser pointer 5 Volume controls 6 Mute button 7 Freeze button 8 Directional pad 9 R-Sync button 10 Source button 11 PD button (page down) 12 Keystone correction 13 Zoom in/zoom out 14 Menu button CAUTION: The remote control has a Class II laser that emits radiation. To reduce the risk of injury to the eyes, do not look directly into the laser light on the remote control and do not point the laser light into anyone's eyes. Battery Disposal: Your projector remote control uses zinc-manganese batteries. If you need to replace the batteries, see your Dell 3200MP Projector Quick Start Card. Do not dispose of used batteries along with household waste. Contact your local waste disposal agency for the address of the nearest battery deposit site. Back to Contents Page Back to Contents Page Installation: Dell™ 3200MP Projector Connecting the Projector Powering On/Off the Projector Adjusting the Projected Image Changing the Lamp Connecting the Projector A. To Computer 1 Power cord 2&3 M1-A to combination VGA and USB cable B. To DVD Player: There are three possible methods of connecting to a DVD player. 1. Connecting with component cable: 1 Power cord 2 M1-A signal cable for HDTV/ component 2. Connecting with S-video cable: 1 Power cord 2 S-video cable 3. Connecting with composite cable: 1 Power cord 2 Composite video cable Powering On/Off the Projector Powering On the Projector NOTE: Turn on the projector before you turn on the source. 1. Remove the lens cap. 2. Ensure that the power cord and appropriate signal cable(s) are securely connected. The power button light blinks green. 3. Press the power button to turn on the projector. The Dell logo will be displayed for 30 seconds. 4. Turn on your source (computer, notebook, DVD, etc...). The projector automatically detects your source. If the "Searching for signal..." message appears on the screen, ensure that the appropriate signal cable(s) are securely connected. If you are connecting multiple sources to the projector simultaneously, press the Source button on the remote control or control panel to select the desired source. 1 Power button 2 Lens cap Powering Off the Projector DO NOT UNPLUG THE PROJECTOR BEFORE PROPERLY SHUTTING DOWN USING THE FOLLOWING STEPS. 1. Press the power button to turn off the projector. The "Power Off the Lamp?" message appears on the OSD. 2. Press the power button again. The cooling fans continue to operate for 2 minutes. 3. If the LAMP light is solid orange, replace the lamp. 4. If the TEMP light is solid orange, the projector has overheated. The display automatically shuts down. Try turning the display on again after the projector cools down. If the problem persists, contact Dell. 5. If the TEMP light is blinking orange, a projector fan has failed and the projector will automatically shut down, If this problem persists, contact Dell. 6. Disconnect the power cord from the electrical outlet and the projector. 7. If you press the power button while the projector is running, the "Power Off the Lamp?" message appears on the screen. To clear the message, press any button on the control panel or ignore the message; the message will disappear after 5 seconds. Adjusting the Projected Image Adjusting the Projector Height To raise the projector: 1. Press the elevator button. 2. Raise the projector to the desired display angle, and then release the button to lock the elevator foot into position. 3. Use the tilt adjustment wheel to fine-tune the display angle. To lower the projector: 1. Press the elevator button. 2. Lower the projector, and then release the button to lock the elevator foot into position. Notice: To avoid damaging the projector, make sure that the elevator foot is fully retracted before placing the projector in its carrying case. 1 Elevator button 2 Elevator foot 3 Tilt adjustment wheel Adjusting the Projector Zoom and Focus CAUTION: To avoid damaging the projector, ensure that the zoom lens is fully retracted before moving the projector or placing the projector in its carrying case. 1. Rotate the zoom ring to zoom in and out. 2. Rotate the focus ring until the image is clear. The projector focuses at distances from 4.0 ft to 39.4 ft (1.2 m to 12 m). 1 Zoom ring 2 Focus ring Adjusting Projection Image Size

Screen (Diagonal) Screen Size Max 29.7" 82.5" 135.2" 187.2" 240.0" 292.8" Min. 24.8" 68.8" 112.7" 156.0" 200.0" 244.0" Max. (WXH) 23.8"X17.8 66.0"X49.5" 108.2"X81.1" 149.8"X112.3" 192.0"X144.0" 234.2"X175.7" Min. (WXH) 19.8X14.9" 55.0"X41.3" 90.1"X67.6" 124.8"X93.6" 160.0"X120.0" 195.2"X146.4"

Distance 4.0' 11.1' 18.2' 25.2' 32.3' 39.4' * This graph is for user reference only. Changing the Lamp Replace the lamp when you see " Lamp is approaching the end of its useful life. Replacement suggested!" message on the screen by carefully following these instructions. If this problem persists, contact Dell. CAUTION: The lamp becomes very hot with use. Do not attempt to replace the lamp after use until the projector has been allowed to cool down for at least 30 minutes. Lamp Changing Procedure: 1. Turn off the projector and disconnect the power cord. 2. Let the projector cool for at least 30 minutes. 3. Lossen the two screws that secure the lamp cover, and remove the cover. 4. Remove the two screws that secure the lamp. 5. Pull up the lamp by its metal handle. 6. Reverse steps 1 through 5 to install the new lamp. 7. Reset the lamp by selecting the left Lamp Reset icon in the OSD Management tab. 8. Dell may require that lamps replaced under warranty are returned to Dell. Otherwise, contact your local waste disposal agency for the address of the nearest deposit site CAUTION: Do not touch the bulb or the lamp glass at any time. The bulb may explode due to improper handling, including the touching of the bulb or the lamp glass. Back to Contents Page Back to Contents Page Using Your Projector: Dell™ 3200MP Projector Control Panel Remote Control On-Screen Display Control Panel Power See "Powering On/Off the Projector." Source Press to step through Analog RGB, DVI, Composite, Component-I, S-video, and Analog YPbPr sources when multiple sources are connected to the projector. R-Sync (Resync) Press to synchronize the projector to the input source. R-Sync will not operate if the OSD is displayed. Menu Press to activate the OSD. An input signal is required to activate the OSD. Four Directional Keys The four directional keys can be used to toggle through the tabs in the OSD. Keystone Press or button to adjust image distortion caused by tilting the projector. (± 30 degrees) Remote Control If the remote control cover is closed: The R-Sync button functions as the right mouse button. The Enter button functions as the left mouse button. If the remote control cover is open, use the directional pad to navigate through the OSD tabs. 1 Directional pad 2 Enter button 3 Laser radiation caution Power See "Power On/Off the Projector." Source Press the Source button to choose Analog RGB, DVI, Composite, Component-I, S-video, and Analog YPbPr sources. R-Sync If the remote control cover is open, the R-Sync button synchronizes the projector to the input source. If the remote control cover is closed, the R-Sync button functions as the right mouse button. Directional Pad The directional pad can be used to control mouse movement when the remote control cover is closed. The mouse function is enabled using the USB connector on the M1-A to combination VGA and USB cable between your computer and the projector. Laser Aim the remote control at the screen, and press and hold the Laser button to activate the laser light. Page Up Press the PU button to page up. Page Down Press the PD button to page down. Menu Press the Menu button to activate the OSD. Use the directional pad and Enter button to navigate through the OSD. Zoom In/Out Press the In button to digitally magnify an image up to 32 times on the screen. Press the Out button to reduce the zoomed image. Freeze Press the Freeze button to temporarily stop motion video. Press the button again to resume . Mute Press the Mute button to mute or unmute the projector speaker. Volume Increases/decrease the speaker volume. Keystone Adjusts image distortion caused by tilting the projector. ( ± 30 degrees) Enter Activates the left mouse button when the remote control cover is closed. On-Screen Display The projector has a multi-language OSD that can only be displayed when an input source is present. The OSD allows you to make image adjustments and change a variety of settings. If the source is a computer, the OSD allows changes to the computer OSD. When using a video source, the OSD allows changes to the video OSD. The projector automatically detects the source. When the OSD is on the screen, press or to navigate through the OSD tabs. Example: All Images--> Computer Image--> Audio--> Management--> Language--> Factory Reset. To make a selection in a tab, press . Press or to make a selection and adjust the settings by pressing or on key pad or "Left" and "Right" button on the remote controller. When an item is selected, the color of the item changes from light blue to dark blue. To exit the OSD, press button on keypad or "Enter" button on the remote controller. All Images Menu Brightness Adjusts the brightness of the image. Press to darken the image. Press to lighten the image. Contrast Controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image. Press to decrease the contrast. Press to increase the contrast. Color Temp. Adjusts the color temperature. With the higher temperature, the screen looks colder; with the lower temperature, the screen looks warmer. User mode activates the values in the "color setting" menu. Color Setting This mode allows for manual adjustment of red, green, and blue color settings. Modifying these values will automatically change the color temperature to "user". Keystone Adjusts image distortion caused by tilting the projector. (± 30degrees) Zoom Press to digitally magnify an image up to 32 times on the projection screen. Press to reduce the zoomed image. Aspect Ratio Select this function to fit 1:1, 16:9 or 4:3 aspect ratio. The input must be a computer signal (through M1-A to VGA cable) less than XGA (1024 x 768), component 576p/ 480i / 480p, S-Video, or Video (composite). If the input signal is a computer signal greater than XGA or component 1080i / 720p, only 16:9 or 4:3 aspect ratio will be available. When an icon is selected, the color of the icon will change to dark blue. White Intensity White Intensity can be adjusted between 0 and 10. Setting 10 will maximize the brightness. Setting 0 will maximize color reproduction quality. Audio Menu Audio Volume Press to decrease the volume. Press to increase the volume. Treble Control the higher frequencies of your audio source. Press to decrease the treble. Press to increase the treble. Bass Control the lower frequencies of your audio source. Press to decrease the bass. Press to increase the bass. Mute Select the left icon to mute the volume. Select the right icon to unmute the volume. . Management Menu Management Menu Location Select the location of the OSD on the screen. Projection Mode Front Projection-Desktop The default setting. Rear Projection-Desktop The projector reverses the image so you can project from behind a translucent screen. Front Projection-Ceiling Mount The projector turns the image upside down for ceiling-mounted projection. Rear Projection-Ceiling Mount The projector simultaneously reverses and turns the image upside down. You can project from behind a translucent screen with a ceiling-mounted projection. Signal Type Manually select signal type RGB, YCbCr, YPbPr. Lamp Hour Displays operating hours since lamp timer reset. Lamp Reset Use this function only after a new lamp is installed in the projector. Select the left Lamp Reset icon (light bulb and arrow under the icon), and press the Enter button to reset the lamp timer. Power Saving Menu Power Saving Use this function to select the power saving delay period. Press "Yes" to go into the "set time" sub menu. Set Time(Min) Set the power saving delay period as you prefer. When the projector is not receiving an input signal for the selected period of time, the projector will automatically enter power saving mode, and turn off the lamp. After a one-minute cooling period, the projector will turn back on with detection of an input signal or by pressing the "Power" button. Language Menu Language Language Press or to select the language you prefer. Factory Reset Menu Factory Reset Select Yes to reset the projector to its factory default settings. Reset items include both computer image and video image settings. Computer Image Menu Computer Image- Note: this menu is only available with computer input signal. Frequency Change the display data frequency to match the frequency of your computer graphic card. If you experience a vertical flickering bar, use the frequency function to make an adjustment. Tracking Synchronize the signal timing of the display with that of the graphic card. If you experience an unstable or flickering image, use the tracking function to correct it. Hor. Position (Horizontal Position) Press to move the image left. Press to move the image right. Ver. Position (Vertical Position) Press to move the image down. Press to move the image up. Video Image Menu Video Image- Note: this menu is only available with S-video, video(composite) or component 480i signal. Color Saturation Adjust a video image from black and white to fully saturated color. Press to decrease the amount of color in the image. Press to increase the amount of color in the image. Sharpness Adjust the sharpness of the image. Press to decrease the sharpness. Press to increase the sharpness. Tint Adjust the color balance of red and green. Press to increase the amount of green in the image. Press to increase the amount of red in the image. Back to Contents Page Back to Contents Page Troubleshooting: Dell™ 3200MP Projector No image appears on the screen Partial, scrolling, or incorrectly displayed image The screen does not display your presentation Image is unstable or flickering Image has vertical flickering bar Image is out of focus The image is stretched when displaying 16:9 DVD Image is reversed Lamp is burned out or makes a popping sound Remote mouse function does not work If you experience problems with your projector, see the following troubleshooting tips. If the problem persists, contact Dell. No image appears on the screen Ensure that the lens cap is removed and the projector is turned on. Ensure the external graphics port is enabled. If you are using a Dell portable computer, press . For other computers, consult your owner's manual. Ensure that all the cables are securely connected as described in "Connecting the Projector." Ensure that the pins of the connectors are not bent or broken. Ensure that the lamp is securely installed (see "Changing the Lamp"). Partial, scrolling, or incorrectly displayed image Press the R-Sync button on the remote control or the control panel. If you are using a Dell portable computer (for other computers consult your owner's manual): 1. Set the resolution of the computer to XGA (1024 x 768): 1a) Right click on the unused portion of your Windows desktop-» Properties-» Settings tab. 1b) Verify the "Screen area" slide bar is set to 1024 x 768 pixels. 2. Press . If you experience difficulty in changing resolutions or your monitor freezes, restart all the equipment and the projector. The screen does not display your presentation If you are using a portable computer, press . Image is unstable or flickering Adjust the tracking in the OSD Computer Image tab. Image has vertical flickering bar Adjust the frequency in the OSD Computer Image tab. Image color is not correct If your graphic card output signal is "sync on Green", and you would like to display VGA at 60Hz signal, please go into "OSD--> Management --> Signal Type" and select "RGB". Image is out of focus Adjust the focus ring on the projector lens. Ensure that the projection screen is within the required distance from the projector (4.0ft [1.2m] to 39.4ft [12m]). The image is stretched when displaying 16:9 DVD The projector automatically detects 16:9 DVD and adjusts the aspect ratio to full screen with a 4:3 (letter-box) default setting. If the image is still stretched, adjust the aspect ratio as follows: If you are playing a 16:9 DVD, select 4:3 aspect ratio type on your DVD player if capable. If you cannot select 4:3 aspect ratio type on your DVD player, select 4:3 aspect ratio in the "All Images" menu within the OSD function. Image is reversed Select Management from the OSD and adjust the projection mode. Lamp is burned out or makes a popping sound When the lamp reaches its end of life, it may burn out and may make a loud popping sound. If this occurs, the projector will not turn back on until the lamp is replaced. To replace the lamp, see "Changing the Lamp". Remote mouse function does not work Ensure the remote is aimed at the remote mouse receiver. Replace batteries on remote if LED light does not operate when a remote button is pressed. Ensure the USB remote mouse cable is properly inserted in the computer. Power cycle the projector (power off projector->allow fans to run two minutes->unplug projector->plug in projector->power on projector). Back to Contents Page Back to Contents Page Specifications: Dell™ 3200MP Projector Light Valve single-chip DLP™ technology Contrast Ratio 1800:1 Typical (Full On/Full Off) Lamp 150-watt, user-replaceable P-VIP lamp Number of Pixels 1024 x 768 Displayable Color 16.7M colors Projection Lens F/2.44–2.69, f=28.8–34.5 mm with 1.2x manual zoom lens Projection Screen Size 25-293 inches (diagonal) Projection Distance 4.0–39.4 ft (1.2m–12m) Video Compatibility NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, SECAM, and HDTV (1080i, 720P, 576P, 480i/P)-compatibility Composite video and S-video capability H. Frequency 15kHz–100kHz horizontal scan V. Frequency 43Hz–120Hz vertical refresh Multimedia Audio one internal speaker with 2-watt output Power Supply universal 100–240V AC 50–60 Hz Power Consumption 210 watts at normal operation I/O Connectors power: AC power input socket computer input: M1-DA for analog/ digital/ component, HDTV and mouse input signal computer output: one 15-pin D-sub video input: one composite video RCA and one S-Video audio input: one phone jack Weight 3.5 lb (1.6 kg) Dimensions (W x H x D) External 9.4 x 7.4 x 2.9 ± 0.034 inches(234 x 189 x 74 ± 1mm) Environmental operating temperature: 10oC–40oC (50oF–104oF) humidity: 80% maximum storage temperature: –20oC to 60oC (–4oF to 140oF) humidity: 80% maximum FCC, CE, VCCI, UL, cUL, TUV GS, ICES-003, MIC, C-Tick,

Safety Regulation Compatibility Modes NEMKO, GOST, PCBC, CCC, PSB, EZU, IRAM, NOM, PSE, CB

Mode Resolution (ANALOG) (DIGITAL)

H. Frequency (KHz) VGA 640X350 V. Frequency (Hz) H. Frequency (KHz) V. Frequency (Hz)

70 31.5 70 31.5 VGA 640X350 85 37.9 85 37.9 VGA 640X400 85 37.9 85 37.9 VGA 640X480 60 31.5 60 31.5 VGA 640X480 72 37.9 72 37.9 VGA 640X480 75 37.5 75 37.5 VGA 640X480 85 43.3 85 43.3 VGA 720X400 70 31.5 70 31.5 VGA 720X400 85 37.9 85 37.9 SVGA 800X600 56 35.2 56 35.2 SVGA 800X600 60 37.9 60 37.9 SVGA 800X600 72 48.1 72 48.1 SVGA 800X600 75 46.9 75 46.9 SVGA 800X600 85 53.7 85 53.7 XGA 1024X768 43.4 35.5 - - XGA 1024X768 60 48.4 60 48.4 XGA 1024X768 70 56.5 70 56.5 XGA 1024X768 75 60.0 75 60.0 XGA 1024X768 85 68.7 - - *SXGA 1280X1024 60 63.98 - - *SXGA 1280X1024 75 79.98 - - *SXGA 1280X1024 85 91.1 - - *SXGA+ 1400X1050 60 63.98 - - *UXGA 1600X1200 60 75.0 - - MAC LC13* 640X480 66.66 34.98 - - MAC II 13* 640X480 66.68 35 - - MAC 16* 832X624 74.55 49.725 - - MAC 19* 1024X768 75 60.24 - - *MAC 1152X870 75.06 68.68 - - MAC G4 640X480 60 31.35 - - MAC G4 640X480 120 68.03 - - MAC G4 1024X768 120 97.09 - - IMAC DV 640X480 117 60 - - IMAC DV 800X600 95 60 - - IMAC DV 1024X768 75 60 - - IMAC DV 1152X870 75 68.49 - - IMAC DV 1280X960 75 75 - - IMAC DV 1280X1024 85 91.1 - - * Compression computer image. Back to Contents Page Back to Contents Page Regulatory Notices: Dell™ 3200MP Projector Federal Communications Commission (FCC) Notice (U.S. Only) FCC Declaration of Conformity CE Declaration of Conformity for a Class B Digital Device Canadian Regulatory Information (Canada Only) EN 55022 Compliance (Czech Republic Only) VCCI Class 2 Notice (Japan Only) MIC Notice (South Korea Only) Polish Center for Testing and Certification Notice NOM Information (Mexico Only) Regulatory Listing Federal Communications Commission (FCC) Notice (U.S. Only) NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received including interference that may cause undesired operation. Instructions to Users: This equipment complies with the requirements of FCC (Federal Communication Commission) equipment provided that the following conditions are met. 1. Power cable: Shielded power cable must be used. 2. Video inputs: The input signal amplitude must not exceed the specified level. NOTICE: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Declaration of Conformity According to 47 CFR, Part 15 of the FCC Rules * For the following named product: DLP Projector 3200MP/DELL CHC7229 * Manufactured at: Coretronic Corporation We hereby declare that this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. * FCC Rules: Tested to comply with FCC part 15, class B * Test site at: Advance Data Technology Corporation No.81-1, Lu Liao Keng, 9 Ling, Wu Lung Tsung, Chiung Lin Hsiang, Hsin Chu Hsien, Taiwan Coretronic Corporation

* Responsible Party for Product Compliance: No 11, Li Hsing Rd, Scienced-Based Industrial Park, Hsinchu, Taiwan Tel: 886-3-5772000 Fax: 886-3-5790066

* Manufacturer Information: Coretronic Corporation RD Center

No 11, Li Hsing Rd, Scienced based Industrial Park, Hsinchu, 300, Taiwan Technology Engineering Associate Vice President November 30, 2002

Hsinchu, November 30, 2002 Mr. Vincent Lin CE Declaration of Conformity for a Class B Digital Device Directives to which conformity is declared: EMC Directives 89/336/EEC and Amending Directive 92/31/EEC And Low Voltage Directive 73/23/EEC Standards to which conformity is declared EN55022: 1998; EN55024: 1998; EN60950: 2000; EN61000-3-2: 1995; EN61000-3-3: 1995 Manufacturer's Name: Coretronic Corporation Manufacturer's Address: No 11, Li Hsing Rd, Scienced-Based Industrial Park, Hsinchu, Taiwan Importer's Address: Dell Products Europe BV Raheen Industrial Estate, Limerick, Ireland Type of Equipment: DLP Projector Model Number(s): 3200MP Reference Report Number: Previously Declared Models: I, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s) and standards. Hsinchu, Taiwan November 30, 2002 Mr. Vincent Lin Head of RD Center Canadian Regulatory Information (Canada Only) This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Note that Industry Canada regulations provided, that changes or modifications not expressly approved by Dell Computer Corporation could void your authority to operate this equipment. This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe B respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada. EN 55022 Compliance (Czech Republic Only) This device belongs to Class B devices as described in EN 55022, unless it is specifically stated that it is a Class A device on the specification label. The following applies to devices in Class A of EN 55022 (radius of protection up to 30 meters). The user of the device is obliged to take all steps necessary to remove sources of interference to telecommunication or other devices. VCCI Class 2 Notice (Japan Only) This equipment complies with the limits for a Class 2 digital device (devices used in or adjacent to a residential environment) and conforms to the standards for information technology equipment that are set by the Voluntary Control Council for Interference for preventing radio frequency interference in residential areas. Class B ITE MIC Notice (South Korea Only) B Class Device Please note that this device has been approved for non-business purposes and may be used in any environment, including residential areas. Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source. The phasing conductor of the room's electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A). To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be located near the equipment and easily accessible. A protection mark "B" confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-42107 and PN-89/E-06251. NOM Information (Mexico Only) The following information is provided on the device(s) described in this document in compliance with the requirements of the official Mexican standards (NOM) Exporter: Dell Computer Corporation One Dell Way Round Rock, TX 78682 Importer: Dell Computer de México, Paseo de la Reforma 2620, 11th Floor Col. Lomas Altas México DF CP 11950 Ship to: Dell Computer de Mexico, S.A. de C.V. al Cuidado de Kuehne & Nagel de México S. de R.I., Avenida Soles No. 55 Col. Peñon de los Baños, 15520 Mexico, D.F. Supply voltage: > 100–240 VAC Frequency: 50–60 Hz Current consumption: 1.2 A Regulatory Listing Safety Certifications: UL 1950 cUL NOM CE Mark--EN60950: 2000 NEMKO EZU IEC 950 TUV GS PCBC GOST CCC PSB IRAM EMC Certifications: FCC Part 15 Class B CE Mark--EN55022:1998 Class B, EN61003-3:1995, EN55024:1998 ICES-003 EZU NEMKO PCBC C-Tick VCCI Class B ITE MIC Back to Contents Page Back to Contents Page Contacting Dell To contact Dell electronically, you can access the following websites: dell.com support.dell.com (technical support) premiersupport.dell.com (technical support for educational, government, healthcare, and medium/large business customers, including Premier, Platinum, and Gold customers) For specific web address for your country, find the appropriate country section in the table below. NOTE: Toll-free numbers are for use within the country for which they are listed. When you need to contact Dell, use the electronic addresses, telephone numbers, and codes provided in the following table. If you need assistance in determining which codes to use, contact a local or an international operator.

Country (City) International Access Code Country Code City Code Department Name or Service Area, Website and E-mail Address Area Code Local Numbers,and Toll-Free Numbers

Anguilla General Support toll free:800-335- 0031

Antigua and Barbuda Argentina General Support 1-800-805-5924 toll free: 0800 444

(Buenos Aires) International Access Code:00 Technical Support and Customer Care Sales 0733 toll free: 0810 444 3355

Country Code:54 Tech Support Fax 11 4515-7139 Customer Care Fax 11 4515-7138 Website: dell.com.ar

Aruba General Support toll-free:800-1578

Australia (Sydney) E-mail (Australia): au_tech_support@dell.com

International Access Code:0011 Country Code:61 Austria (Vienna) International Access Code:900 Country Code:43 E-mail (New Zealand): nz_tech_support@dell.com Home and Small Business 1-300-65-55-33 Government and Business toll free: 1-800-633- 559 Preferred Accounts Division (PAD) toll free: 1-800-060- 889 Customer Care toll free: 1-800-819- 339 Corporate Sales toll free: 1-800-808- 385 Transaction Sales toll free: 1-800-808- 312 Fax toll free: 1-800-818- 341 Switchboard 01 491 040 Home/Small Business Sales 01 795676-02 Home/Small Business Fax 01 795676-05 Home/Small Business Customer Care 01 795676-03 Preferred Accounts/Corporate Customer Care 0660-8056 Home/Small Business Technical Support 01 795676-04 Preferred Accounts/Corporate Technical Support 0660-8779 Website: support.euro.dell.com E-mail: tech_support_central_europe@dell.com

Bahama General Support toll-free:1-866-278- 6818 Barbados General Support 1-800-534-3142

Belgium (Brussels) International Access Code:00 Technical Support 02 481 92 88 Customer Care 02 481 91 19 Home/Small Business Sales toll free: 0800 16884

Country Code:32 Corporate Sales 02 481 91 00 Fax 02 481 92 99 Switchboard 02 481 91 00 Website: support.euro.dell.com E-mail: tech_be@dell.com E-mail for French Speaking Customers: support.euro.dell.com/be/fr/emaildell/ Bermuda General Support 1-800-890-0748 Bolivia General Support toll free: 800-10- 0238

Brazil International Access Customer Support, Technical Support toll free: 0800 90 3355

Code:00 Country Code:55 British Virgin Islands Technical Support Fax 51 481-5470 Customer Care Fax 51 481-5480 Sales toll free: 0800 90 3390 Website: dell.com/br General Support toll-free:1-866-278- 6820

Brunei Country Code:673 Customer Technical Support (Penang, Malaysia) Customer Service (Penang, Malaysia) Transaction Sales (Penang, Malaysia) 604 633 4966 604 633 4949 604 633 4955

Canada (North York, Ontario) International Access Code:011 Automated Order-Status System toll free: 1-800-433- 9014 AutoTech (Automated technical support) toll free: 1-800-247- 9362 Customer Service Home & Home Office & Small 1-800-847-4096

Business Customer Service Medium, Large, Commercial, Government (100+ Employees) Technical Support Home & Home Office & Small Business Technical Support Medium, Large, Commercial, Government (100+ Employees) 1-800-326-9463 1-800-847-4096 1-800-387-5757

Sales (General) 1-800-387-5752 TechFax toll free: 1-800-950- 1329 Cayman Islands General Support 1-800-805-7541

Chile (Santiago) Country Code:56 China (Xiamen) Country Code:86 Sales, Customer Support, and Technical Support Tech Support website: support.ap.dell.com/china Tech Support E-mail: cn_support@dell.com toll free: 1230-020- 4823

Tech Support Fax 818-1350 Home and Small Business Technical Support toll free: 800 858 2437 Corporate Accounts Technical Support toll free: 800 858 2333 Customer Experience toll free: 800 858 2060 Home and Small Business toll free: 800 858 2222 Preferred Accounts Division toll free: 800 858 2062 Large Corporate Accounts North toll free: 800 858

Large Corporate Accounts North Government and Education 2999 toll free: 800 858 2955

Large Corporate Accounts East toll free: 800 858 2020

Large Corporate Accounts East Government and Education toll free: 800 858 2669

Large Corporate Accounts Queue Team toll free: 800 858 2572 Large Corporate Accounts South toll free: 800 858 2355 Large Corporate Accounts West toll free: 800 858 2811 Large Corporate Accounts GCP toll free: 800 858 2055 Large Corporate Account Key Accounts toll-free:800-858- 2628 Large Corporate Accounts Spare Parts toll free: 800-858-- 2621 Colombia General Support 980-9-15-3978 Costa Rica General Support 0800-012-0435

Czech Republic (Prague) International Access Code:00 Country Code:420 Denmark (Horsholm) International Access Code:00 Technical Support 02 22 83 27 27 Customer Care 02 22 83 27 11 Fax 02 22 83 27 14 TechFax 02 22 83 27 28 Switchboard 02 22 83 27 11 Website: support.euro.dell.com E-mail: czech_dell@dell.com Technical Support 70230182 Customer Care(Relational) 70230184 Home/Small Business Customer Care 32875505 Switchboard (Relational) 32871200

Country Code:45Fax Switchboard (Relational) 32871201 Switchboard (Home/Small Business) 32875000 Fax Switchboard (Home/Small Business) 32875001 Website: support.euro.dell.com E-mail Support (portable computers): den_nbk_support@dell.com E-mail Support (desktop computers): den_support@dell.com E-mail Support (servers): Nordic_server_support@dell.com Dominica General Support toll free: 1-866-278- 6821

Dominican Republic General Support toll free: 1-800-156- 1588

Ecuador General Support toll-free 999-119 El Salvador General Support 01-889-753-0777

Finland (Helsinki) International Access Code:990 Country Code:358 France (Paris) (Montpellier) International Access Code:00 Technical Support 09 253 313 60 Technical Support Fax 09 253 313 81 Relational Customer Care 09 253 313 38 Home/Small Business Customer Care 09 693 791 94 Fax 09 253 313 99 Switchboard 09 253 313 00 Website: support.euro.dell.com E-mail: fin_support@dell.com Home and Small Business Technical Support 0825 387 270 Customer Care 0825 823 833

Country Code:33Switchboard 0825 004700 Switchboard (calls from outside of France) 04 99 75 40 00 Sales 0825 004 700 Fax (calls from outside of France) 04 99 75 40 001 Website: support.euro.dell.com E-mail: support.euro.dell.com/fr/fr/emaildell/ Corporate Technical Support 0825 004 719 Customer Care 0825 338 339 Fax 01 55 94 71 01 Switchboard 01 55 94 71 00 Sales 01 55 94 71 00

Germany (Langen) International Access Code:00 Country Code:49 Technical Support 06103 766-7200 Home/Small Business Customer Care 0180-5-224 400 Global Segment Customer Care 06103 766-9570 Preferred Accounts Customer Care 06103 766-9420 Large Accounts Customer Care 06103 766-9560 Public Accounts Customer Care 06103 766-9555 Switchboard 06103 766-7000 Website: support.euro.dell.com E-mail: tech_support_central_europe@dell.com

Grenda General Support toll free:1-866-540- 3355 Guatemala General Support 1-800-999-0136 Guyana General Support toll free:1-877-440- 6511

Hong Kong International Access Code:001 Country Code:852 Technical Support(Dimension™ and Inspiron™ ) Technical Support (OptiPlex™, Latitude ™ , and Dell Precision™ ) Customer Service (non-technical, post-sales issues) 296-93188 296-93191 800-93-8291

Transaction Sales toll free: 800 96 4109 Large Corporate Accounts HK toll free: 800 96 4108 Large Corporate Accounts GCP HK toll free: 800 90 3708 India Technical Support 1600-33-8045 Sales 1600-33-8044

Ireland (Cherrywood) International Access Code:16 Country Code:353 Italy (Milan) International Access Ireland Technical Support 1850 543 543 UK Technical Support (dial within UK only) 0870 908 0800 Home User Customer Care 01 204 4095 Small Business Customer Care 01 204 4444 Corporate Customer Care 01 204 4003 UK Customer Care (dial number within UK only) 0870 906 0010 Ireland Sales 01 204 4444 UK Sales (dial within UK only) 0870 907 4000 SalesFax 01 204 0144 Fax 01 204 5960 Switchboard 01 204 4444 Website: support.euro.dell.com E-mail: dell_direct_support@dell.com Home and Small Business Technical Support 02 577 826 90 Customer Care 02 696 821 14

Code:00 Country Code:39Fax 02 696 821 13 Switchboard 02 696 821 12 Website: support.euro.dell.com E-mail: support.euro.dell.com/it/it/emaildell/ Corporate Technical Support 02 577 826 90 Customer Care 02 577 825 55 Fax 02 577 035 30 Switchboard 02 577 821 Website: support.euro.dell.com E-mail: support.euro.dell.com/it/it/emaildell/ Jamaica General Support (dial from within Jamaica only) 1-800-404-9205

Japan (Kawasaki) International Access Code:001 Korea (Seoul) International Access Code:001 Country Code:82 Web site: support.jp.dell.com Technical Support toll free: 0120-981- 690 Technical Support outside of Japan 44 556-3468 Customer Care 44 556-4240 Technical Support toll free: 080-200- 3800 Sales toll free: 080-200- 3600 Customer Service (Penang, Malaysia) toll free: 604-633- 4949 Customer Service (Seoul, Korea) 080-200-3800 Fax 2194-6202 Switchboard 2194-6000 Latin America Customer Technical Support (Austin, Texas, U.S.A.) 512 728-4093

Customer Service (Austin, Texas, U.S.A.) 512 728-3619

Fax (Technical Support and Customer Service) (Austin, Texas, U.S.A.) 512 728-3883

Luxembourg International Access Code:00 Country Code:352 Macao Country Code:853 Malaysia (Penang) International Access Code:00 Country Code:60 Sales (Austin, Texas, U.S.A.) 512 728-4397 SalesFax (Austin, Texas, U.S.A.) 512 728-4600 or 728-3772 Technical Support (Brussels, Belgium) 02 481 92 88 Home/Small Business Sales (Brussels, Belgium) toll free: 080016884 Corporate Sales (Brussels, Belgium) 02 481 91 00 Customer Care (Brussels, Belgium) 02 481 91 19 Switchboard (Brussels, Belgium) 02 481 91 00 Fax (Brussels, Belgium) 02 481 92 99 Website: support.euro.dell.com E-mail: tech_be@dell.com Technical Support toll free: 0800 582 Customer Service (Penang, Malaysia) 604 633 4949 Transaction Sales toll free: 0800 581 Technical Support toll free: 1 800 888 298 Customer Service 4 633 4949 Transaction Sales toll free: 1 800 888 202 Corporate Sales toll free: 1 800 888 213

Mexico Customer Technical Support 001-877-384-8979 or 001-877-269- 3383 Sales 50-81-8800 or 01-800-888-3355 Customer Service 001-877-384-8979 or001-877-269-3383 Main 50-81-8800 or 01-800-888-3355 Montserrat General Support toll free:1-866-278- 6822

Netherlands Antilles Netherlands (Amsterdam) International Access Code:00 Country Code:31 General Support 001-800-882-1519 Technical Support 20 674 4500 Home/Small and Medium Business 20 674 5500 Home/Small and Medium Business Fax 20 674 4775 Home/Small and Medium Business Customer Care 20 674 4200 Corporate 20 674 5000 Corporate Fax 20 674 4779 Corporate Customer Care 20 674 4325 Website: support.euro.dell.com E-mail: support.euro.dell.com/nl/nl/emaildell/

New Zealand E-mail (New Zealand): nz_tech_support@dell.com E-mail (Australia): au_tech_support@dell.com Home and Small Business 0800 446 255 Government and Business 0800 444 617 Sales 0800 441 567 Fax 0800 441 566 Nicaragua General Support 001-800-220-1006

Norway (Lysaker) International Access Code:00 Technical Support 671 16882 Relational Customer Care 671 17514 Home/Small Business Customer Care 231 62298

Country Code:47Switchboard 671 16800 Fax Switchboard 671 16865 Website: support.euro.dell.com E-mail Support (portable computers): nor_nbk_support@dell.com E-mail Support (desktop computers): nor_support@dell.com E-mail Support (servers): nordic_server_support@dell.com Panama General Support 001-800-507-0962 Peru General Support 0800-50-669

Poland (Warsaw) International Access Code:011 Country Code:48 Portugal International Access Code:00 Country Code:47 Customer Service Phone 22 57 95 700 Customer Care 22 57 95 999 Sales 22 57 95 999 Switchboard 22 57 95 999 Customer Service Fax 22 57 95 806 Reception Desk Fax 22 57 95 998 Website: support.euro.dell.com E-mail: pl_support@dell.com Technical Support 35 800 834 077 Customer Care 800 300 415 or 800 834 075 Sales 800 300 410 or 800 300 411 or 800 300 412 or 121 422 07 10 Fax 35 121 424 01 12 E-mail: support.euro.dell.com/es/es/emaildell/

Puerto Rico General Support 1-800-805-7545 St. Kitts and Nevis General Support toll free:1-877-441- 4731 St. Lucia General Support 1-800-882-1521

St. Vincent and the Grenadines Singapore (Singapore) International Access Code:005 Country Code:65 South Africa (Johannesburg) International Access Code:09/091 Country Code:27 General Support toll free:1-877-441- 4740 Technical Support toll free: 800 6011 051 Customer Service (Penang, Malaysia) 604 633 4949 Transaction Sales toll free: 800 6011 054 Corporate Sales toll free: 800 6011 053 Technical Support 011 709 7710 Customer Care 011 709 7707 Sales 011 709 7700 Fax 011 706 0495 Switchboard 011 709 7700 Website: support.euro.dell.com E-mail: dell_za_support@dell.com

Southeast Asian/Pacific Countries Spain Customer Technical Support, Customer Service, and Sales (Penang, Malaysia) Home and Small Business 604 633-4810

(Madrid) International Access Code:00 Country Code:34 Technical Support 91 902 100 130 Customer Care 91 902 118 540 Sales 91 902 118 541 Switchboard 91 902 118 541 Fax 91 902 118 539 Website: support.euro.dell.com Sweden (Upplands Vasby) International Access Code:00 Country Code:46 Switzerland (Geneva) International Access Code:00 Country Code:41 E-mail: support.euro.dell.com/es/es/emaildell/ Corporate Technical Support 91 902 100 130 Customer Care 91 902 118 546 Switchboard 91 722 92 00 Fax 91 722 95 83 Website: support.euro.dell.com E-mail: support.euro.dell.com/es/es/emaildell/ Technical Support 08 590 05 199 Relational Customer Care 08 590 05 642 Home/Small Business Customer Care 08 587 70 527 Employee Purchase Program (EPP) Support 20 140 14 44 Fax Technical Support 08 590 05 594 Sales 08 590 05 185 Website: support.euro.dell.com E-mail: swe_support@dell.com E-mail Suport for Latitude and Inspiron: Swe-nbk_kats@dell.com E-mail Suport for OptiPlex: Swe_kats@dell.com E-mail Suport for Servers: nordic_server_support@dell.com Technical Support (Home and Small Business) 22 0844 811 411 Technical Support (Corporate) 22 0844 822 844 Customer Care (Home and Small Business) 22 0848 802 202 Customer Care(Corporate) 0848 821 721 Switchboard 22 799 01 01 Fax 22 799 01 90 Website: support.euro.dell.com E-mail:swisstech@dell.com

Taiwan International Access E-mail for French-speaking HSB and Corporate Customers: support.euro.dell.com/ch/fr/emaildell/ Technical Support (portable and desktop computers) toll free: 00801 86 1011

Code:002 Country Code:886 Thailand International Access Code:001 Country Code:66 Trinidad and Tobago Turks and Caicos Islands U.K. (Bracknell) International Access Code:44 Country Code:44 Technical Support (Servers) toll free: 0080 60 1256 Transaction Sales toll free:0800 651 228 or 0800 33 556 Corporate Sales toll free: 0080 651 227/ 0800 33 555 Technical Support toll free: 088 006 007 Customer Service (Penang, Malaysia) 604 633 4949 Sales toll free: 088 006 009 General Support 1-800-805-8035 General Support toll free:1-866-540- 3355 Technical Support (Corporate/Preferred Accounts/PAD [1000+ employees]) 0870 908 0500 Technical Support (Direct/PAD and general) 0870 908 0800 Global Accounts Customer Care 373 185 01344 or 373 186 Corporate Customer Care 0870 908 0500 Preferred Accounts (500-5000 employees) Customer Care 01344 373 196 Central Government Customer Care 01344 373 193 Local Government & Education Customer Care 01344 373 199

Health Customer Care 01344 373 194 Home/Small Business Sales 0870 907 4000 Home/Small Business Customer Care 0870 906 0010 Corporate/Public Sector Sales 01344 860 456 Website: support.euro.dell.com Customer Care website: dell.co.uk/lca/customerservices E-mail: dell_direct_support@dell.com Uruguay General Support toll free:000-413- 598-2521

U.S.A. (Austin, Texas) International Access Code:011 Country Code:1 Automated Order-Status System toll free: 1-800-433- 9014 AutoTech (portable and desktop computers) toll free: 1-800-247- 9362 Projectors Technical Support toll free: 1-877-459- 7298 Customer Service toll free: 1-800-624- 9897 Dell Sales toll free: 1-800-289- 3355 or toll free: 1-800- 879-3355 Dell Outlet Store (Dell refurbished computers) toll free: 1-888-798- 7561 Software and Peripherals Sales toll free: 1-800-671- 3355 Spare Parts Sales toll free: 1-800-357- 3355 Extended Service and Warranty Sales toll free: 1-800-247- 4618 Fax toll free: 1-800-727- 8320

Dell Services for the Deaf, Hard-of-Hearing, or Speech-Impaired toll free: 1-877- DELLTTY

(1-877-335-5889) U.S. Virgin Islands General Support 1-877-673-3355 Venezuela General Support 8001-3605 Back to Contents Page


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply