DELFIELD F18WR39 (01) PDF MANUAL


Post questions, comments, reviews or errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD DELFIELD F18WR39 (01) PDF MANUAL


PDF Content Summary: F18 SERIES Service and Installation Manual Please read this manual completely before attempting to install or operate this equipment! Notify carrier of damage! Inspect all components immediately.Refrigerated Work Tables, Salad Tables & Freezer Bases Important Information Read Before Use Please Save These Instructions! July 2013 F18 Series Service and Installation Manual Important Warning And Safety Information WARNING Read This Manual Thoroughly Before Operating, Installing, Or Performing Maintenance On The Equipment. WARNING Failure To Follow Instructions In This Manual Can Cause Property Damage, Injury Or Death. WARNING Do Not Store Or Use Gasoline Or Other Flammable Vapors Or Liquids In The Vicinity Of This Or Any Other Appliance. WARNING Unless All Cover And Access Panels Are In Place And Properly Secured, Do Not Operate This Equipment. WARNING This Appliance Is Not Intended For Use By Persons Who Lack Experience Or Knowledge, Unless They Have Been Given Supervision Or Instruction Concerning Use Of The Appliance By A Person Responsible For Their Safety. WARNING This Appliance Is Not To Be Played With. WARNING Do Not Clean With Water Jet. WARNING Do Not Use Electrical Appliances Inside The Food Storage Compartment Of This Appliance. CAUTION Observe the following: • Minimum clearances must be maintained from all walls and combustible materials. • Keep the equipment area free and clear of combustible material. • Allow adequate clearance for air openings. • Operate equipment only on the type of electricity indicated on the specification plate. • Unplug the unit before making any repairs. • Retain this manual for future reference. 2For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com F18 Series Service and Installation ManualContents Receiving & Inspecting .........................................................3 Serial Number Location ........................................................4 Warranty Information ............................................................4 Regulatory Certifications .......................................................4 Specifications .................................................................... 5-7 Installation ............................................................................8 Operation ..............................................................................9 Temperature Settings ..........................................................10 Maintenance .................................................................. 11-12 Wiring Diagrams ........................................................... 13-16 Replacement Part Lists ................................................. 17-20 Replacement Part Assemblies ...................................... 21-24 Standard Labor Guidelines ..................................................25 Notes ............................................................................ 26-27 Receiving and Inspecting the Equipment Even though most equipment is shipped crated, care should be visually inspect the refrigeration package. Be sure lines are taken during unloading so the equipment is not damaged while secure and base is still intact. being moved into the building. 7. Freight carriers can supply the necessary forms upon request. 1. Visually inspect the exterior of the package an skid or 8. Retain all crating material until an inspection has been container. Any damage should be noted and reported to made or waived. the delivering carrier immediately. 2. If damaged, open and inspect the contents with the carrier. Uncrating the Equipment 3. In the event that the exterior is not damaged, yet upon opening, there is concealed damage to the equipment notify the carrier. Notification should be made verbally as well as in written form. First cut and remove the banding from around the crate. Remove the front of the crate material, use of some tools will be required. If the unit is on legs remove the top of the crate as well and lift the unit off the skid. If the unit is on casters it can 4. Request an inspection of the concealed equipment. This be "rolled" off the skid. should be done within 10 days from receipt of the equipment. 5. Check the lower portion of the unit to be sure legs or casters are not bent. 6. Also open the compressor compartment housing and For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com 3 F18 Series Service and Installation Manual Serial Number Location The serial number on all self-contained F18 Series refrigerated work tables and freezer bases is located on the electrical specifications tag affixed inside the compressor section next to the pressure control. On remote refrigerated bases with doors, the tag is inside the unit on the coil side. On remote refrigerated bases with drawers, the tag is affixed to the drawer divider. On remote freezer bases, the tag is located on the inside back of the unit. Always have the serial number of your unit available when calling for parts or service. A complete list of authorized Delfield parts depots is available at delfield.com. ©2013 The Delfield Company. All rights reserved. Reproduction without written permission is prohibited. “Delfield” is a registered trademark of The Delfield Company. Warranty Information Visit delfield.com/minisite/service/warranty_info to: • Register your product for warranty. • Verify warranty information. • View and download a copy of your warranty. Regulatory Certifications Models are certified by: National Sanitation Foundation (NSF) Underwriters Laboratories (UL) Underwriters Laboratories of Canada (ULC) 4For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com F18 Series Service and Installation ManualSpecifications Remote Refrigerated Work Tables Model # Of Doors Base FTVolume 3 Area Shelf FT2 Volts/Hertz/ Phase Amps BTU Load EVAP. BTU/°TD F18WR31 (1) 19” 70 7.56 2.56 115/60/1 3.0 383 120/3° F18WR39 (1) 27” 124 10.23 3.95 115/60/1 3.0 465 120/4° F18WR44 (2) 19” 70 12.14 5.12 115/60/1 3.0 605 120/5° F18WR52 (1) 19” & (1) 27” 70/124 15.12 6.51 115/60/1 3.0 686 120/6° F18WR60 (2) 27” 124 18.10 7.90 115/60/1 3.0 768 120/6° F18WR70 (2) 32” 140 21.23 9.64 115/60/1 3.0 869 120/7° F18WR79 (2) 27” & (1) 19” 124/70 24.48 10.29 115/60/1 6.0 1050 240/4° F18WR87 (3) 27” 124 27.46 11.85 115/60/1 6.0 1131 240/5° Self-Contained Refrigerated Work Tables Model # Of Doors For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com 5 Shelf Max Load (lbs) R-404A oz. H.P. NEMA Plug F18WC39 (1) 19” 70 7.56 2.56 115/60/1 8.0 383 1462 16 1/5 5-15P F18WC47 (1) 27” 124 10.23 3.95 115/60/1 8.0 465 1462 16 1/5 5-15P F18WC52 (2) 19” 70 12.14 5.12 115/60/1 8.0 605 1462 16 1/5 5-15P F18WC60 (1) 19” & (1) 27” 70/124 15.12 6.51 115/60/1 8.0 686 1462 16 1/5 5-15P F18WC68 (2) 27” 124 18.10 7.90 115/60/1 10.0 768 1462 16 1/4 5-15P F18WC78 (2) 32” 140 21.23 9.64 115/60/1 10.0 869 1994 16 1/4 5-15P F18WC87 (2) 27” & (1) 19” 124/70 24.48 10.29 115/60/1 10.0 1050 2261 16 1/4 5-15P F18WC95 (3) 27” 124 27.46 11.85 115/60/1 10.0 1131 2261 16 1/4 5-15P Remote Refrigerated Mega Top Salad Tables Model # Of Doors Load Shelf (lbs) Max Base FTVolume 3 Area Shelf FT2 Volts/Hertz/ Phase Amps BTU Load BTU System Cap. EVAP. BTU/°TD Base/Rail F18MR31A (1) 19” 70 4.14 6 115/60/1 3.0 280/265 120/2°/12/22° F18MR44A (2) 19” 70 7.15 6 115/60/1 3.0 444/265 120/4°/12/22° F18MR44D (2) 19” 70 7.15 12 115/60/1 3.0 444/529 120/4°/22/25° F18MR52A (1) 19” & (1) 27” 70/124 8.97 6 115/60/1 3.0 515/265 120/4°/12/22° F18MR52D (1) 19” & (1) 27” 70/124 8.97 12 115/60/1 3.0 515/529 120/4°/22/25° F18MR52E (1) 19” & (1) 27” 70/124 8.97 18 115/60/1 3.0 515/794 120/4°/31/26° Self-Contained Refrigerated Mega Top Salad Tables Model # Of Doors Load Shelf (lbs) Max Base FTVolume 3 Volts/Hertz/ # of Pans Phase BTU Load Amps Base/Rail Load Shelf (lbs) Max Base FTVolume 3 Volts/Hertz/ # of Pans Phase BTU Load BTU System Cap. R-404A NEMA Amps Base/Rail Base/Rail oz. H.P. Plug F18MC39A (1) 19” 70 4.14 6 115/60/1 10.0 280/265 1903/925 16 1/4 5-15P F18MC39D (1) 19” 70 4.14 12 115/60/1 10.0 280/529 1903/1156 16 1/4 5-15P F18MC52A (2) 19” 70 7.15 6 115/60/1 10.0 444/265 1903/925 16 1/4 5-15P F18MC52D (2) 19” 70 7.15 12 115/60/1 10.0 444/529 1903/1156 16 1/4 5-15P F18MC52E (2) 19” 70 7.15 18 115/60/1 10.0 444/794 1903/1321 16 1/4 5-15P F18MC60A (1) 19” & (1) 27” 70/124 8.97 6 115/60/1 10.0 515/265 2314/864 16 1/4 5-15P F18MC60D (1) 19” & (1) 27” 70/124 8.97 12 115/60/1 10.0 515/529 2314/1141 16 1/4 5-15P F18MC60E (1) 19” & (1) 27” 70/124 8.97 18 115/60/1 10.0 515/794 2314/1361 16 1/4 5-15P F18MC60F (1) 19” & (1) 27” 70/124 8.97 24 115/60/1 10.0 515/1058 2314/1540 16 1/4 5-15P F18 Series Service and Installation Manual Specifications Remote Refrigerated Salad Top Tables Model # Of Doors 6For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com BTU Load Base/Rail Evap. BTU/°TD Base/Rail F18SR31A (1) 19” 70 4.14 6 115/60/1 3.0 280/265 120/2°/13/21° F18SR44A (2) 19” 70 7.15 6 115/60/1 3.0 491/441 120/4°/13/21° F18SR44B (2) 19” 70 7.15 8 115/60/1 3.0 491/441 120/4°/16/22° F18SR44C (2) 19” 70 7.15 10 115/60/1 3.0 491/441 120/4°/19/23° F18SR52A (1) 19” & (1) 27” 70/124 8.97 6 115/60/1 3.0 532/529 120/4°/13/21° F18SR52B (1) 19” & (1) 27” 70/124 8.97 8 115/60/1 3.0 532/529 120/4°/16/22° F18SR52C (1) 19” & (1) 27” 70/124 8.97 10 115/60/1 3.0 532/529 120/4°/19/23° F18SR52D (1) 19” & (1) 27” 70/124 8.97 12 115/60/1 3.0 532/529 120/4°/23/23° Self-Contained Refrigerated Salad Top Tables Model # Of Doors Shelf Max Load (lbs) Base FTVolume 3 # of Pans Volts/Hertz/ Phase Amps R-404A oz. H.P. NEMA Plug F18SC39A (1) 19” 70 4.14 6 115/60/1 10.0 280/265 1903/745 16 1/4 5-15P F18SC39B (1) 19” 70 4.14 8 115/60/1 10.0 280/353 1903/867 16 1/4 5-15P F18SC52A (2) 19” 70 7.15 6 115/60/1 10.0 444/265 1903/745 16 1/4 5-15P F18SC52B (2) 19” 70 7.15 8 115/60/1 10.0 444/353 1903/867 16 1/4 5-15P F18SC52C (2) 19” 70 7.15 10 115/60/1 10.0 444/441 1903/971 16 1/4 5-15P F18SC52D (2) 19” 70 7.15 12 115/60/1 10.0 444/529 1903/1061 16 1/4 5-15P F18SC60A (1) 19” & (1) 27” 70/124 8.97 6 115/60/1 10.0 515/265 2314/667 16 1/4 5-15P F18SC60B (1) 19” & (1) 27” 70/124 8.97 8 115/60/1 10.0 515/353 2314/798 16 1/4 5-15P F18SC60C (1) 19” & (1) 27” 70/124 8.97 10 115/60/1 10.0 515/441 2314/916 16 1/4 5-15P F18SC60D (1) 19” & (1) 27” 70/124 8.97 12 115/60/1 10.0 515/529 2314/1023 16 1/4 5-15P Remote Refrigerated Reduced Height Rail Model # Of Doors Shelf Max BTU Load (lbs) Base FTVolume 3 # of Volts/Hertz/ BTU Load System Pans Phase Amps Base/Rail Cap. Base/Rail Evap. BTU/°TD Base/Rail F18DR44 (2) 19” 70 9.54 5.12 10 115/60/1 3.0 547/441 120/5°/19/23° F18DR52 (1) 19” & (1) 27” 70/124 13.89 6.51 12 115/60/1 3.0 625/529 120/5°/23/23° F18DR60 (2) 27” 124 16.64 7.9 16 115/60/1 5.0 703/617 120/6°/26/24° F18DR70 (2) 32” 140 22.96 9.64 18 115/60/1 5.0 800/794 120/7°/32/24° F18DR79 (1) 19” & (2) 27” 70/124 22.47 10.29 18 115/60/1 5.0 962/882 240/4°/36/25° F18DR87 (3) 27” 124 25.22 11.85 22 115/60/1 5.0 1032/970 240/4°/39/25° Self-Contained Refrigerated Reduced Height Rail Model # Of Doors Shelf Max Load (lbs) Base FTVolume 3 Area Shelf FT2 # of Pans Volts/Hertz/ Phase BTU Load Amps Base/Rail Shelf Max NEMA Load (lbs) Base FTVolume 3 Area Shelf FT2 # of Pans Volts/Hertz/ BTU Load BTU System R-404A Phase Amps Base/Rail Cap. Base/Rail oz. H.P. Plug F18DC52 (2) 19” 70 9.54 5.12 12 115/60/1 10.0 547/529 1903/1061 16 1/4 5-15P F18DC60 (1) 19” & (1) 27” 70/124 13.89 6.51 14 115/60/1 12.0 625/617 2314/1121 24 1/3 5-15P F18DC68 (2) 27” 124 16.64 7.9 18 115/60/1 12.0 703/794 2314/1544 24 1/3 5-15P F18DC82 (2) 32” 140 22.96 9.64 20 115/60/1 14.0 800/882 3097/1648 32 1/2 5-20P F18DC91 (1) 19” & (2) 27” 70/124 22.47 10.29 22 115/60/1 14.0 962/1058 3807/1839 32 1/2 5-20P F18DC99 (3) 27” 124 25.22 11.85 24 115/60/1 14.0 1032/1147 3807/1839 32 1/2 5-20P F18 Series Service and Installation ManualSpecifications Remote Refrigerated Reduced Height Rail BTU Load Evap. BTU/°TD Model # Of Doors Base/Rail Base/Rail For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com 7 # of Pans F18RR44 (2) 19” 70 9.49 5.12 115/60/1 3.0 547/441 120/5°/19/23° 10 F18RR52 (1) 19” & (1) 27” 70/124 11.81 6.51 115/60/1 3.0 625/529 120/5°/23/23° 12 F18RR60 (2) 27” 124 14.14 7.9 115/60/1 5.0 703/617 120/6°/26/24° 16 F18RR70 (2) 32” 140 17.05 9.64 115/60/1 5.0 800/794 120/7°/32/24° 18 F18RR79 (1) 19” & (2) 27” 70/124 18.68 10.29 115/60/1 5.0 962/882 240/4°/36/25° 18 F18RR87 (3) 27” 124 21.30 11.85 115/60/1 5.0 1032/970 240/4°/39/25° 22 Self-Contained Refrigerated Reduced Height Rail Model # Of Doors Shelf Max Load (lbs) Base FTVolume 3 Area Shelf FT2 Volts/Hertz/ Phase Amps R-404A oz. H.P. NEMA Plug F18RC52 (2) 19” 70 9.49 5.12 115/60/1 10.0 547/529 1903/1061 12 16 1/4 5-15P F18RC60 (1) 19” & (1) 27” 70/124 11.81 6.51 115/60/1 12.0 625/617 2314/1121 14 24 1/3 5-15P F18RC68 (2) 27” 124 14.14 7.9 115/60/1 12.0 703/794 2314/1544 16 24 1/3 5-15P F18RC82 (2) 32” 140 17.05 9.64 115/60/1 14.0 800/882 3097/1648 20 32 1/2 5-20P F18RC91 (1) 19” & (2) 27” 70/124 18.68 10.29 115/60/1 14.0 962/1058 3807/1839 22 32 1/2 5-20P F18RC99 (3) 27” 124 21.30 11.85 115/60/1 14.0 1032/1147 3807/1839 24 32 1/2 5-20P Remote Freezer Base Model # Of Doors Load Shelf (lbs) Max Base FTVolume 3 Area Shelf FT2 Volts/Hertz/ Phase BTU Load BTU System # of Amps Base/Rail Cap. Base/Rail Pans BTU Load Base/Rail Evap. BTU/°TD F18FR35 (1) 19” 70 5.58 2.56 115/60/1 10.0 943 160/6° F18FR50 (2) 19” 70 12.21 5.12 115/60/1 10.0 1471 160/9° F18FR58 (1) 19” & (1) 27” 70/124 15.00 6.51 115/60/1 10.0 1844 160/10° F18FR66 (2) 27” 124 17.79 7.9 115/60/1 10.0 2020 160/11° F18FR76 (2) 32” 140 21.28 9.64 115/60/1 10.0 2437 160/13° Self-Contained Freezer Base Model # Of Doors Load Shelf (lbs) Max Base FTVolume 3 Area Shelf FT2 Volts/Hertz/ Phase Amps NEMA Plug F18FC43 (1) 19” 70 5.58 2.56 115/60/1 10.0 943 1558 1/3 24 5-15P F18FC62 (2) 19” 70 12.21 5.12 115/60/1 12.0 1471 1776 1/2 40 5-15P F18FC70 (1) 19” & (1) 27” 70/124 15.00 6.51 115/60/1 16.0 1647 2713 3/4 56 5-20P F18FC78 (2) 27” 124 17.79 7.9 115/60/1 16.0 1824 2713 3/4 56 5-20P F18FC88 (2) 32” 140 21.28 9.64 115/60/1 16.0 2045 2713 3/4 56 5-20P Self-Contained Dual Rails Model # Of Doors Load Shelf (lbs) Max Base FTVolume 3 Area Shelf FT2 Volts/Hertz/ Phase BTU Load BTU System R-404A Amps Base/Rail Cap. Base/Rail H.P. oz. Load Shelf (lbs) Max Base FTVolume 3 Area Shelf FT2 Volts/Hertz/ Phase BTU Load BTU System R-404A NEMA Amps Base/Rail Cap. Base/Rail H.P. oz. Plug F18PD48 (1) 27” 124 9.38 3.95 115/60/1 10.0 424/1058 2001/1865 1/5, 1/3 40 5-20P F18PD72 (2) 27” 124 16.64 7.90 115/60/1 12.7 703/1588 2001/3174 1/5. 1/2 48 5-20P F18 Series Service and Installation Manual Installation Location These units are intended for indoor use only. Be sure the location chosen has a floor strong enough to support the total weight of the cabinet and contents. A fully loaded 72” (183cm) long model may weigh as much as 1500 pounds (680kg)! Reinforce the floor as necessary to provide for maximum loading. It is very important to allow for proper air flow, both inside and outside. Avoid hot corners and locations near stoves, ovens and other pieces of cooking equipment. It is recommended that the unit be installed no closer than 1” (2.54cm) from any wall. Do not install the unit near any combustible material or object affected by heat or moisture. PDL models also require 14" (36cm) clearance at the top and 6" (15cm) clearance at the bottom (casters). Leveling A level cabinet looks better and will perform better because the drain pan will drain properly, the doors will line up with the frames properly, and the cabinet will not be subject to undue strain. A unit on legs will have an adjustable bullet foot on each leg, adjust each for a level unit. A unit on casters will not be adjustable. Be sure the unit is on a level floor, make necessary changes to the floor for proper level. Lock all front casters to ensure the stability of the unit. 8 For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com Plumbing Self-contained models are standard with a condensate evaporator. If, for some reason a unit does not have a condensate evaporator, or if the evaporator fails, the unit’s drain must have an outlet to an appropriate drainage area or container. A refrigerated rail will have a 1" (2.54cm) drain which will need to be run to an appropriate floor drain or container. The drain will be stubbed to the bottom of the machine compartment. Either run drain to a floor drain or add a valve to the base of the machine compartment and drain the rail to a container when convenient. The LiquiTec option will NOT have a drain available. Moisture collecting from improper drainage can create a slippery surface on the floor and a hazard to employees. It is the owner’s responsibility to CAUTION provide a container or outlet for drainage. Electrical connection Refer to the specification pages amperage data, the serial tag, your local code or the National Electrical Code to be sure the unit is connected to the proper power source. A protected circuit of the correct voltage and amperage must be run for connection of the line cord, or permanent connection of the unit. Self-contained units with a cord and plug have an ON/OFF switch located directly behind the louvered panel covering the compressor section. Simply turn the switch to ON to begin operation. The power switch must be turned to OFF and the unit disconnected from the power source whenever performing service or maintenance functions. Never operate the unit without the louvered panel in place! If electrical receptacles are to be mounted in the unit’s backsplash, they must be wired independently from the existing unit wiring. F18 Series Service and Installation Manualquality in the rail it is recommended that product be rotated every four hours. If adding any item to the unit, be sure to keep in mind the location of the refrigeration lines on wrapped rail units. A refrigeration leak in a rail is extremely difficult and costly to repair. In some cases it cannot be repaired at all. Refrigerator Evaporator Fan Operation When the refrigerator is initially powered up or immediately following a power outage the unit will begin cooling after a 3-6 minute delay. During normal operation the evaporator fan pulses independently of the compressor as dictated by the controller as follows: 1. During the cooling mode, compressor and evaporator fan run simultaneously. 2. During the compressor off mode, evaporator fan pulses three minutes on and three minutes off. 3. During an actual defrost event other than the off-cycle defrost, compressor stays off but the evaporator fan runs continuously. Cooling Cycle Defrost Cycle Compressor On Compressor Off Compressor Off Evap Fan Evap Fan On Off For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com 9 Evap Fan On Evap Fan Off Refrigerator Operation Power up the unit by turning ON the unit’s ON/OFF switch. Delfield refrigerated bases are designed to maintain an operational temperature of 36°F to 40°F (2°C to 4°C). Temperature in the salad top and refrigerated rail opening is 33°F to 41°F (0°C to 5°C) with pans recessed 2” (5.1cm) on a standard wrapped refrigerated rail or flush with the LiquiTec option at 86°F (30°C) ambient room temperature. Do not place hot pans on/against the blue ABS liner. Do not throw items into the storage area. Failure to heed these recommendations could result in damage to the interior of the cabinet or to the blower coil. Overloading the storage area, restricting the air flow, and continuous opening and closing of the doors and drawers will hamper the units ability to maintain operational temperature. Refrigerated rail units Product in the rail should be removed to the refrigerated base at the end of the day. This allows you to turn the rail off at night to save energy and the rail will have time to defrost as needed. It also helps maintain product quality. The standard wrapped refrigerated units are controlled by the pressure control which is set to maintain the proper rail temperature. An on/off switch is also provided for the rail and is required to be shut off at night. The rail switch shuts off the rail only. With a LiquiTec rail a thermostat is provided to maintain rail temperature as well as the rail on/off switch. The LiquiTec rail is required to be shut Evap Fan On off at night as well to allow for defrosting. To ensure product Evap Fan Off X Cycles On 3-Min, Off 3-Min X Freezer Operation Power up the unit by turning ON the unit’s ON/OFF switch. Delfield freezer bases are designed to maintain an operational temperature of 0°F (-18°C). Do not place hot pans on/against the blue ABS liner. Do not throw items into the storage area. Failure to heed these recommendations could result in damage to the interior of the cabinet or to the blower coil. Overloading the storage area, restricting the air flow, and continuous opening and closing of the doors and drawers will hamper the units ability to maintain operational temperature. Freezer Evaporator Fan Operation The evaporator fan(s) and condenser fan will cycle off and on with the compressor to conserve energy. The temperature control will cycle the compressor and condenser fan motor and evaporator fan motor to maintain box temperature at the control setting. Cooling Cycle Defrost Cycle All Freezers Self-Contained Freezers Remote Freezers Compressor On Compressor Compressor Compressor Off On Off Evap Fan On Evap Fan Off Evap Fan Off Evap Fan Off Freezer Defrost Self-contained models use hot gas to defrost the evaporator coils. Remote freezers use electric defrost. F18 Series Service and Installation Manual Temperature Control Settings A thermostat controls temperature in the self-contained Please make small incremental adjustments if F18WC, F18FC, F18MC base, F18SC base, F18RC base, a temperature adjustment is necessary. It may F18DC base, F18PD base and F18PD rails. take an hour or longer to realize the temperature Thermostats are located in the machine compartment. They are field adjustable and do not require a service agent. The change depending on the application and location of the unit. factory setting is 2.5. Set toward 1 for higher temperatures Contact the service department at Delfield +1 and toward 7 for lower temperatures. (989) 773-7981 or your local service agent A thermostat controls temperature in the remote F18FR. The temperature control is located in the machine compartment. It is field adjustable and does not require a service agent. for additional assistance. Delfield is not responsible for charges incurred while adjusting the thermostat. The factory setting for a remote freezer is 0°F cut-in with a 5°F differential. Pressure Control Settings A pressure control controls temperature in the F18MC mega top, F18SC salad top, F18RC rail and F18DC rail. The factory recommended low-pressure control settings are: 55psi cut-in and 30psi cut-out to maintain proper temperature for product. The interior temperature is controlled by the thermostat mounted in the mechanical compartment. A pressure control is located in the machine compartment. An adjustable control has the word COLDER on the knob, with an arrow to indicate the adjustment direction. These controls are field adjustable and do not require a service agent. In attempting to adjust the pressure control, you can do damage to your unit by accidentally adjusting the differential. Please make small incremental adjustments if a temperature adjustment is necessary. It may take an hour or longer to realize the temperature change depending on the application and location of the unit. Please contact the service department at Delfield (800) 733-8829 or your local service agent. Delfield is not responsible for charges incurred while having the pressure control adjusted. 10For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com F18 Series Service and Installation Manual Maintenance Door Gasket Maintenance Reassembly Door gaskets require regular cleaning to prevent mold and mildew Push the drawer tracks into the drawer cage. The blue safety clip build up and also to retain the elasticity of the gasket. Gasket cleaning must remain pushed towards the back. Lift up and slide the drawer can be done with the use of warm soapy water. Avoid full strength track all the way into the drawer cage. The blue safety clip will lock cleaning products on gaskets as this can cause them to become in place automatically. Once all tracks are replaced, insert the drawer brittle and crack. Never use sharp tools or knives to scrape or clean box. Rest the drawer box bottom track on the front track roller. Then the gasket. Gaskets can be easily replaced and do not require the use push the drawer back in place SLOWLY. When the drawer box is about of tools or an authorized service person. The gaskets are “Dart” style half way in you will hit a STOP. You must lift the front of the drawer up and can be pulled out of the groove in the door and new gaskets can approximately 1⁄2” (1.3cm) to continue inward. Clean tracks as often be “pressed” back into place. as possible. The cleaner the tracks are the better they will operate. Drain Maintenance - Base Caster Maintenance Each unit has a drain located inside the unit that removes the Wipe casters with a damp cloth monthly to prevent corrosion. condensation from the evaporator coil and routes it to an external condensate evaporator pan. Each drain can become loose or disconnected during normal use. If you notice water accumulation on the inside of the unit be sure the drain tube is connected to the evaporator drain pan. If water is collecting underneath the unit make The power switch must be turned to OFF and the unit disconnected from the power source whenever performing service, maintenance functions or cleaning the refrigerated area. sure the end of the drain tube is in the condensate evaporator in the Refrigerators and Freezers machine compartment. The leveling of the unit is important as the units are designed to drain properly when level. Be sure all drain lines are free of obstructions. The interior and exterior can be cleaned using soap and warm water. If this isn’t sufficient, try ammonia and water or a nonabrasive liquid cleaner. When cleaning the exterior, always rub with the “grain” of Drawer Maintenance the stainless steel to avoid marring the finish. Do not use an abrasive Drawer Assembly Cleaning cleaner because it will scratch the stainless steel and can damage the The drawer assembly is designed to be cleaned easily. Both drawer breaker strips and gaskets. and tracks are removable without tools. The drawer tracks are Stainless Steel Care and Cleaning dishwasher safe or can be cleaned in a sink with detergents and a soft bristle brush. Drawers and tracks should be cleaned on a weekly basis. To prevent discoloration of rust on stainless steel several important steps need to be taken. First, we need to understand the properties of stainless steel. Stainless steel contains 70- 80% iron, which will Remove Drawers Pull the drawer box out until it stops. Lift up on the drawer front and pull the drawer box completely out. Using a soft bristle brush, clean the track on the bottom of the drawer box. When finished, it should be wiped clean of all food and debris. rust. It also contains 12-30% chromium, which forms an invisible passive film over the steels surface, which acts as a shield against corrosion. As long as the protective layer is intact, the metal is still stainless. If the film is broken or contaminated, outside elements can begin to breakdown the steel and begin to form discoloration of rust. Proper cleaning of stainless steel requires soft cloths or plastic Tracks scouring pads. The drawer box assembly must be removed. Pull the drawer tracks NEVER USE STEEL PADS, WIRE BRUSHES OR SCRAPERS! out until they hit a stop. Locate blue safety clips towards the back of each drawer track. Blue safety clips have a tab on the top. Push the tab back until it clicks. Lift up and pull the drawer tracks all the way out of the drawer cage. The drawer tracks are dishwasher safe or can be cleaned in a sink with detergents and a soft bristle brush. Drawers and tracks should be cleaned on a weekly basis. Using a soft bristle brush, wash the track making sure each roller is thoroughly cleaned. The drawer cage should be cleaned with a soft bristle brush, removing any food and debris gathered on the bottom Cleaning solutions need to be alkaline based or non-chloride cleaners. Any cleaner containing chlorides will damage the protective film of the stainless steel. Chlorides are also commonly found in hard water, salts, and household and industrial cleaners. If cleaners containing chlorides are used be sure to rinse repeatedly and dry thoroughly. Routine cleaning of stainless steel can be done with soap and water. Extreme stains or grease should be cleaned with a non-abrasive tab on top of blue safety clip cleaner and plastic scrub pad. Always rub with the grain of the steel. There are stainless steel cleaners available which can restore and preserve the finish of the steels protective layer. Early signs of stainless steel breakdown are small pits and cracks. If this has begun, clean thoroughly and start to apply stainless steel cleaners in attempt to restore the passivity of the steel. ledge. Once it’s cleaned thoroughly with a soft bristle brush, wipe Never use an acid based cleaning solution! Many food remaining debris clean with a soft towel. products have an acidic content, which can deteriorate the finish. Be sure to clean the stainless steel surfaces of ALL food products. Common items include, tomatoes, peppers and other vegetables. For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com 11 F18 Series Service and Installation Manual Maintenance, continued Cleaning the Condenser Coil Preventing blower coil corrosion In order to maintain proper refrigeration performance, the To help prevent corrosion of the blower coil, store all acidic items, condenser fins must be cleaned of dust, dirt and grease regularly. such as pickles and tomatoes, in sealable containers. Immediately It is recommended that this be done at least every three months. wipe up all spills. If conditions are such that the condenser is totally blocked in three months, the frequency of cleaning should be increased. Clean the condenser with a vacuum cleaner or stiff brush. If extremely dirty, a commercially available condenser cleaner may be required. Units with pans should be operated with pans in place. Operating the unit without all pans in place will lower efficiency and may damage the unit. Failure to maintain a clean condenser coil can initially cause high temperatures and excessive run times. Continuous operation with a dirty or clogged condenser coil can result in compressor failure. Neglecting the condenser coil cleaning procedures will void any warranties associated with the compressor and cost to replace the Continuous opening and closing of the doors will hamper the unit’s ability to maintain optimum refrigeration temperature. Top section is not intended for overnight storage. Product should be removed from pans. Pans can remain in unit while empty. compressor.Never use a high-pressure water wash for this cleaning procedure as water can damage the electrical components located near or at the condenser coil. Doors/Hinges Over time and with heavy use doors the hinges may become loose. If this happens tighten the screws that mount the hinge brackets to the frame of the unit. Loose or sagging doors can cause the hinges to pull out of the frame, which may damage both the doors and the hinges. In some cases this may require qualified service agents or maintenance personnel to perform repairs. Do not place hot pans on/against the blue ABS liner. Do not throw items into the storage area. Failure to follow these recommendations could result in damage to the interior of the cabinet or to the blower coil. Overloading the storage area, restricting the airflow, and continuous opening and closing of the doors and drawers will hamper the units ability to maintain operational temperature. Refrigerated rail units Product in the rail should be removed to the refrigerated base at the end of the day. This allows you to turn the rail off at night to save energy and to defrost the rail. It also helps maintain product quality. The standard wrapped refrigerated rail units are controlled by a low- pressure control that is set to maintain the proper rail temperature. An on/off switch is also provided for the rail and is required to be shut off at night. With a LiquiTec rail a thermostat is provided to maintain rail temperature as well as the rail on/off switch. The LiquiTec rail is required to be shut off at night as well to allow for defrosting. To ensure product quality in the rail it is recommended that product be rotated every four hours. If adding any item to the unit, be sure to keep in mind the location of the refrigeration lines on wrapped rail units. A refrigeration leak in a rail is extremely difficult and costly to repair. In some cases it cannot be repaired at all. 12For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com Wiring Diagram, F18WC Wiring Diagram, F18WR F18 Series Service and Installation Manual 13 For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com F18 Series Service and Installation Manual For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com 14Wiring Diagram, F18MC, F18SC, F18DC & F18RC Wiring Diagram, F18MR, F18SR, F18DR & F18RR Wiring Diagram, F18FC Wiring Diagram, F18FR F18 Series Service and Installation Manual 15 For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com F18 Series Service and Installation Manual For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com 16Wiring Diagram, F18PD

F18 Series Service and Installation Manual Replacement Parts F18DC 3516053 Coil, solenoid, 120V/50/60HZ (rail) *000-248-0030 Coil assembly, R404A *000-BN5-0035 Condensing unit, 1/2hp, R404a *000-BN5-0037 Condensing unit, 1/3hp, R404a *000-BN5-0030 Condensing unit, 1/4hp, R404a 9321040 Shelf support screw (coil side) 9321132 Shelf support screw (wall side) 2190154 Switch, rocker 2194201 Thermostat, rail 3516225 Valve, expansion (rail) 3516102 Valve, solenoid (rail) 2194824 Control, Danfoss, GDM, 115V 2193927 Control, pressure, low F18FC 3234392 Hinge, pan cover, center *000-BN5-0053 Condensing unit, 1/3HP, w/rec, hg 3234282 Hinge, pan cover, left *000-BN5-0054 Condensing unit, 1/2HP, low temp, hg 3234266 Hinge, pan cover, right *000-BN5-0055 Condensing unit, 3/4HP, low temp, hg 9321374 Hinge, pin (for pan cover) *000-249-0004 Coil, assembly, freezer, R404a 0160179 Hinge Kit 2194758-4 Control, Danfoss, Freezer, 115V 3234645 Leg, 6", s/s 0160179 Hinge Kit 3977984 Shelf, 19" door 3234645 Leg, 6", s/s 3977998 Shelf, 24" door 9321040 Shelf support screw (coil side) 3978014 Shelf, 27" door 9321132 Shelf support screw (wall side) 3977983 Shelf, 32" door 3234290 Shelf support, 1" blue 2190154 Switch, rocker 3977984 Shelf, 19" door 3516225 Valve, expansion (rail) 3977998 Shelf, 24" door 3516102 Valve, solenoid (rail) 3978014 Shelf, 27" door 3234290 Shelf support, 1" blue 3977983 Shelf, 32" door 9321040 Shelf support screw (coil side) 2190154 Switch, rocker 9321132 Shelf support screw (wall side) F18FR F18DR *000-249-0006 Coil assembly, frz evap, remote 3516053 Coil, solenoid, 120V/50/60HZ (rail) 3516053 Coil, solenoid, 120V/50/60HZ *000-248-0030 Coil assembly, R404A 3516056 Control, Temperature *000-248-0037 Coil assembly, R404A, Fan Lt 0160179 Hinge Kit 2194824 Control, Danfoss, GDM, 115V 3234645 Leg, 6", s/s 3234392 Hinge, pan cover, center 9321040 Shelf support screw (coil side) 3234282 Hinge, pan cover, left 9321132 Shelf support screw (wall side) 3234266 Hinge, pan cover, right 3234290 Shelf support, 1" blue 9321374 Hinge, pin (for pan cover) 3977984 Shelf, 19" door 0160179 Hinge Kit (left or right hinged) 3977998 Shelf, 24" door 3234645 Leg, 6", s/s 3978014 Shelf, 27" door 3977984 Shelf, 19" door 3977983 Shelf, 32" door 3977998 Shelf, 24" door 2194151 Timer, Paragon, #8145-00 3978014 Shelf, 27" door 3516102 Valve, solenoid 3977983 Shelf, 32" door 3234290 Shelf support, 1" blue *Replacement part assemblies on pages 19-22. For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com 17

F18 Series Service and Installation Manual Replacement Parts, continued F18MC F18PD48 030-209-0030 Angle, Coil, Top Baffle *000-248-0037 Coil assembly, R404A, Fan Lt 3516053 Coil, solenoid, 120V/50/60HZ (rail) *000-BN5-0040 Condensing Assembly, 1/3-1/5 Stacked *000-248-0030 Coil assembly, R404A 2194824 Control, Danfoss, GDM, 115V *000-248-0037 Coil assembly, R404A, Fan Lt 2194938 Control, Tstat, Danfoss, Etc1h-1 *000-BN5-0030 Condensing unit, 1/4hp, R404a *000-402-0056 Cover Assembly, hinged, 6 pan, l/t 2194824 Control, Danfoss, GDM, 115V *000-187-006B Door Assembly, ref, 27x26, lt 2193927 Control, pressure, low 3234645 Leg, 6, s/s, removable Foot 3234392 Hinge, pan cover, center *356-478-0038 Panel, louver, 14.0, sw Cut, lh 3234282 Hinge, pan cover, left 3978014 Shelf, wire, coated 3234266 Hinge, pan cover, right 3234290 Support, shelf, plastic 9321374 Hinge, pin (for pan cover) 2190154 Switch, rocker, 20a/125v 0420068 Hinge kit, lo profile (left or right) 3516135 Thermometer, hanging, 4 2190154 Switch, rocker 3516225 Valve, expansion (rail) 3516102 Valve, solenoid (rail) F18PD72 3234645 Leg, 6", s/s *000-248-0030 Coil assembly, R404A *000-BN5-003Y Condensing Assembly, 1/2-1/5 Stacked 2194824 Control, Danfoss, GDM, 115V F18MR 2194938 Control, Tstat, Danfoss, Etc1h-1 030-209-0030 Angle, Coil, Top Baffle *000-402-0056 Cover Assembly, hinged, 6pan, l/t 3516053 Coil, solenoid, 120V/50/60HZ (rail) *000-187-006B Door Assembly, ref, 27x26, lt *000-248-0030 Coil assembly, R404A *000-187-006A Door Assembly, ref, 27x26, rt *000-248-0037 Coil assembly, R404A, Fan Lt 3234645 Leg, 6, s/s, removable Foot 2194824 Control, Danfoss, GDM, 115V *356-478-0039 Panel, louver, 18.0, sw Cut, lh 3234392 Hinge, pan cover, center 3978014 Shelf, wire, coated 3234282 Hinge, pan cover, left 3234290 Support, shelf, plastic 3234266 Hinge, pan cover, right 2190154 Switch, rocker, 20a/125v 9321374 Hinge, pin (for pan cover) 3516135 Thermometer, hanging, 4 0420068 Hinge kit, lo profile (left or right) 3234645 Leg, 6", s/s 9321041 Nut, acorn (for pan cover) 2190154 Switch, rocker 2194201 Thermostat, rail 3516225 Valve, expansion (rail) 3516102 Valve, solenoid (rail) *Replacement part assemblies on pages 19-22. 18For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com F18 Series Service and Installation Manual Replacement Parts, continued F18RC 3516053 Coil, solenoid, 120V/50/60HZ (rail) *000-248-0030 Coil assembly, R404A *000-BN5-0035 Condensing unit, 1/2hp, R404a *000-BN5-0037 Condensing unit, 1/3hp, R404a *000-BN5-0030 Condensing unit, 1/4hp, R404a 9321040 Shelf support screw (coil side) 9321132 Shelf support screw (wall side) 2190154 Switch, rocker 2194201 Thermostat, rail 3516225 Valve, expansion (rail) 3516102 Valve, solenoid (rail) 2194824 Control, Danfoss, GDM, 115V 2193927 Control, pressure, low F18SC 3234392 Hinge, pan cover, center 030-209-0030 Angle, Coil, Top Baffle 3234282 Hinge, pan cover, left 3516053 Coil, solenoid, 120V/50/60HZ (rail) 3234266 Hinge, pan cover, right *000-248-0030 Coil assembly, R404A 9321374 Hinge, pin (for pan cover) *000-248-0037 Coil assembly, R404A, Fan Lt 0160179 Hinge Kit *000-BN5-0030 Condensing unit, 1/4hp, R404a 3234645 Leg, 6", s/s 2194824 Control, Danfoss, GDM, 115V 3977984 Shelf, 19" door 2193927 Control, pressure, low 3977998 Shelf, 24" door 3234392 Hinge, pan cover, center 3978014 Shelf, 27" door 3234282 Hinge, pan cover, left 3977983 Shelf, 32" door 3234266 Hinge, pan cover, right 3234290 Shelf support, 1" blue 9321374 Hinge, pin (for pan cover) 9321040 Shelf support screw (coil side) 0420068 Hinge kit, lo profile (left or right) 9321132 Shelf support screw (wall side) 3234645 Leg, 6", s/s 2190154 Switch, rocker 2190154 Switch, rocker 3516225 Valve, expansion (rail) 3516225 Valve, expansion (rail) 3516102 Valve, solenoid (rail) 3516102 Valve, solenoid (rail) F18RR 3516053 Coil, solenoid, 120V/50/60HZ (rail) *000-248-0030 Coil assembly, R404A *000-248-0037 Coil assembly, R404A, Fan Lt 2194824 Control, Danfoss, GDM, 115V 3234392 Hinge, pan cover, center 3234282 Hinge, pan cover, left 3234266 Hinge, pan cover, right 9321374 Hinge, pin (for pan cover) 0160179 Hinge Kit 3234645 Leg, 6", s/s 3977984 Shelf, 19" door 3977998 Shelf, 24" door 3978014 Shelf, 27" door 3977983 Shelf, 32" door 3234290 Shelf support, 1" blue *Replacement part assemblies on pages 19-22. For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com 19

F18 Series Service and Installation Manual Replacement Parts, continued F18SR 030-209-0030 Angle, Coil, Top Baffle 3516053 Coil, solenoid, 120V/50/60HZ (rail) *000-248-0030 Coil assembly, R404A *000-248-0037 Coil assembly, R404A, Fan Lt 2194824 Control, Danfoss, GDM, 115V 3234392 Hinge, pan cover, center 3234282 Hinge, pan cover, left 3234266 Hinge, pan cover, right 9321374 Hinge, pin (for pan cover) 0420068 Hinge kit, lo profile (left or right) 3234645 Leg, 6", s/s 2190154 Switch, rocker 2194201 Thermostat, rail 3516225 Valve, expansion (rail) 3516102 Valve, solenoid (rail) F18WC *000-248-0030 Coil assembly, R404A *000-248-0037 Coil assembly, R404A, Fan Lt *000-BN5-0030 Condensing unit, 1/4hp, R404a *000-BN5-0031 Condensing unit, 1/5hp, R404a 2194810 Control, Danfoss, GDM, 115V 0160179 Hinge Kit 3234645 Leg, 6", s/s 3977984 Shelf, 19" door 3977998 Shelf, 24" door 3978014 Shelf, 27" door 3977983 Shelf, 32" door 2190154 Switch, rocker 3234290 Shelf support, 1" blue 9321040 Shelf support screw (coil side) 9321132 Shelf support screw (wall side) 20For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com F18WR *000-248-0030 Coil assembly, R404A *000-248-0037 Coil assembly, R404A, Fan Lt 2194810 Control, Danfoss, GDM, 115V 0160179 Hinge Kit (left or right hinged) 3234645 Leg, 6", s/s 3977984 Shelf, 19" door 3977998 Shelf, 24" door 3978014 Shelf, 27" door 3977983 Shelf, 32" door 3234290 Shelf support, 1" blue 9321040 Shelf support screw (coil side) 9321132 Shelf support screw (wall side) *Replacement part assemblies on pages 19-22.

F18 Series Service and Installation Manual Replacement Part Assemblies 3 4 1 2 3 4 5 5 2 1 7 6 6 8 8 10 9 9 7 Key Part Number Description Key Part Number Description - 000-249-0004 Coil Assembly, Evap, Freezer - 000-249-0006 Coil Assembly, Freezer Evap, Remote 1 030-262-0001 Side, evaporator 1 030-262-0001 Side, evaporator 2 2160023 Fan, axiel 2 2160023 Fan, axiel 3 2160024 Guard, fan, 4.7", SC120-W2 4 030-260-0001 Top, frz, evaporator 5 030-259-0000 Front, enclosure 6 3516271 Valve, expansion, R404a 7 265-261-0001 Pan, freezer evaporator 8 3516073 Coil, Evaporator 9 030-263-0001 Back, evaporator - 2184318 Harness, coil, frz, male - 2194808 Probe, Defrost, Danfoss, Control - 2194809 Probe, Temp, Sensor, Danfoss 3 2160024 Guard, fan, 4.7", SC120-W2 4 030-260-0001 Top, frz, evaporator 5 030-259-0000 Front, enclosure 6 3516271 Valve, expansion, R404a 7 3516073 Coil, Evaporator 8 2194034 Heater, Defrost 9 265-261-0001 Pan, freezer evaporator 10 030-263-0001 Back, evaporator - 2194046 Control, Limit, Fan Delay/Defrost - 2194631 Fuse, Defrost Heater, 7 Amp - 2184323 Harness, coil, frz, male, remote 1 2 4 1 2 4 3 3 5 6 6 5 7 98 7 Key Part Number Description - 000-248-0037 Coil Assembly, R404A, Ref, Fan Lt Key Part Number Description - 000-248-0030 Coil Assembly, R404A, Ref 1 2160024 Guard, fan, 4.7" 2 2160023 Fan, axiel, 120V 3 3516095 Coil, evaporator 4 030-232-0003 Back, evaporator, enclosure 5 3516273 Expansion valve, 1/4, R-404a 6 030-233-0001 Side, coil, angled 7 075-231-0033 Drip pan, evaporator 8 030-234-0003 Front, coil - 2184317 Harness, coil - 2194808 Probe, Defrost, Danfoss, Control 8 1 2160024 Guard, fan, 4.7" 2 2160023 Fan, axiel, 120V 3 3516095 Coil, evaporator 4 030-232-0003 Back, evaporator, enclosure 5 000-BNH-0030 Drip pan, evaporator 6 030-233-0038 Side, coil, angled, Rt, Blank 7 3516273 Expansion valve, 1/4, R-404a 8 030-234-0003 Front, coil 9 030-233-0039 Side, Coil, Angled, Lt, 2Fan - 2184317 Harness, coil - 2194808 Probe, Defrost, Danfoss, Control - 2194809 Probe, Temp, Sensor, Danfoss - 2194809 Probe, Temp, Sensor, Danfoss For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com 21

F18 Series Service and Installation Manual Replacement Part Assemblies, continued 2 2 3 4 3 4 1 1 5 5 6 6 7 7 8 8 Key Part Number Description Key Part Number Description - 000-BN5-0030 Assembly, 1/4 HP Condensing Unit - 000-BN5-0031 Assembly, 1/5 Condensing Unit 1 2160028 Fan, Axial, 5.5", 120V 1 2160028 Fan, Axial, 5.5.", 120V 2 2160030 Guard, Fan, 6.0" 2 2160030 Guard, Fan, 6.0" 3 026-C58-0037 Shroud, Condenser Coil 3 026-C58-0037 Shroud, Condenser Coil 4 3526999 Compressor, Danfoss, NF5.5CLX 4 3526997 Compressor, Danfoss, TF4CLS 5 2194787 Start Capacitor 5 2194787 Start Capacitor 3516444 Comp, Relay, Overload, NF5.5CLX 3516446 Comp, Relay, Danfoss 6 3516322 Filter Dryer 6 3516322 Filter Dryer 7 075-231-0030 Condensate Pan 7 075-231-0030 Condensate Pan 8 3516454 Condenser Coil 8 3516454 Condenser Coil 5 7 8Key Part Number Description - 000-BN5-0054 Assembly, 1/2HP Cond, Low, Hot gas 1 3516554 Blade, Fan, 9.00” 2 2160019 Guard, Fan, Wire 3 2162716 Motor, Fan, 16W, 115V, CW 4 3516324 Cutout, High Pressure 5 3527001 Compressor, SC12CLX.2,115/60HZ 6 3516322 Drier, Filter, (2)Inlet 7 2194789 Capacitor, Start, 240MFD 8 3516441 Relay, Comp, SC12CLX.2 9 3516455 Coil, Condenser, 1/2 HP - 024-034-0031 Pan, Comp, 18.00 22For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com 6 1 2 4 3 2 1 3 9 4 Key Part Number Description - 000-BN5-0055 Assembly, 3/4 HP Cond, Low, Hot gas 1 2160019 Guard, fan condenser 2162716 Motor, condenser fan 16W, 155V 3516433 Blade, fan 10” CW 2 3527002 Compressor, SC18CLS.2, 115V60hz 3516442 Capacitor, start, run assembly 3 3516322 Filter drier 4 3516456 Coil, condenser, 3/4hp

F18 Series Service and Installation Manual Replacement Part Assemblies, continued 5 6 2 4 1 2 3 3 4 1 7 5 7 6 8 9 8 9 Key Part Number Description Key Part Number Description - 000-BN5-0035 Assembly, 1/2HP Condenser, Med - 000-BN5-0037 Assembly, 1/3 Condensing Unit 1 3516554 Condenser fan blade 1 2160028 Fan, Axial, 5.5", 120V 2 2160019 Condenser fan guard 2 2160030 Guard, Fan, 6.0" 3 2162716 Condenser fan motor, 115V 3 026-C58-0037 Shroud, Condenser Coil 4 3516462 Capacitor, start-run assy 4 3527000 Compress, Danfoss, NF7CLS 5 3527026 Compressor, Danfoss, SC12MLX 5 2194788 Start Capacitor 6 3516331 Hi pressure switch 3516438 Relay, overload, compressor 7 3516322 Filter Drier 6 3516322 Filter Drier 8 075-231-0031 Pan, Condensate 7 3516458 Receiver tank 9 3516455 Condenser coil 8 075-231-0030 Pan, Condensate 9 3516454 Condenser Coil 2 3 4 7 8 5 6 1 9 10 11 Key Part Number Description - 000-BN5-0053 Assembly, 1/3HP Cond, w/rec, hg 1 2160028 Fan, Axial, 5.5", 120V 2 2160030 Guard, Fan, 6.0" 3 3516053 Coil, Solenoid, 120V 4 3516102 Valve, Solenoid, 1/4ODF 5 3527000 Compressor, NF7.0,115/60HZ, Danfoss 6 3516438 Relay, Comp, ovld 2194788 Capacitor, Start, 320MFD 7 000-998-0030 High Pressure Assembly, 8Amp 8 3516397 Accumulator 9 3516322 Filter Drier, (2)Inlet 10 3516458 Receiver 11 3516454 Coil, Condenser For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com 23

F18 Series Service and Installation Manual Replacement Part Assemblies, continued 000-BN5-003Y Assembly, 1/2-1/5 Stacked, 3516457 Blade, Fan, 7.25 Dia., 3516433 Blade, fan, 25deg, 10", cw 2194789 Capacitor, start, 240mfd 359-478-003E Panel, louver, 15.0, ptb 2194787 Capacitor, start, 280mfd 359-478-003D Panel, louver, 18.0, ptb 3516454 Coil, Condenser, 1/5, 1/4, 356-478-0038 Panel, louver, 14.0, sw Cut,lh 3516455 Coil, Condenser, 1/2 Hp 356-478-0039 Panel, louver, 18.0, sw Cut, lh 3526997 Compressor, 1/5hp, 115/60, r404a 3527001 Compressor, sc12clx.2, 115/60hz, 3516322 Drier, filter, (2)inlet 2160020 Guard, Fan, 7.25 2160019 Guard, fan, wire 2162717 Motor, fan, 9w, 115v, cw 2162513 Motor, fan, 35w, blast 3516193 Regulator, pressure, 1/2 3516446 Relay, Compressor, Danfoss 3516441 Relay, compressor, sc12clx.2 3516225 Valve, expansion, frz, 1/4ton 000-187-0081 Door Assembly, ref, 27x26, rt, 430 000-187-0082 Door Assembly, ref, 27x26, lt, 430 000-187-006B Door Assembly, ref, 27x26, lt 000-187-006A Door Assembly, ref, 27x26, rt 1701185 Gasket, door, 27, mark7 0420067 Hinge Kit 000-BN5-0040 Assy, 1/3-1/5 Stacked, 3516457 Blade, Fan, 7.25 Dia. 2194787 Capacitor, start, 280mfd 2194788 Capacitor, start, 320mfd 3516454 Coil, Cond., 1/5, 1/4 3526997 Comp, 1/5hp, 115/60, r404a 3527000 Comp, nf7cls, 115v/60hz 3516322 Drier, filter, (2)inlet 2160020 Guard, Fan, 7.25 2162717 Motor, fan, 9w,115v,cw 000-402-0054 Cover Assembly, hinged, 6 Pan, ptl 000-402-0056 Cover Assembly, hinged, 6pan, l/t 3516193 Regulator, pressure, 1/2 9321374 Pin, hinge, salad Pan 3516446 Relay, Comp, Danfoss 3234266 Hinge, pan Cover, end, rh, 3516438 Relay, comp, ovld, nf7clx 3516225 Valve, exp, frz, 1/4ton 3234282 Hinge, pan Cover, end, lh, 3234392 Hinge, pan Cover, 24For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com

F18 Series Service and Installation Manual Standard Labor Guidelines To Repair Or Replace Parts On Delfield Equipment Advice and recommendations given by Delfield Service Technicians do not constitute or guarantee any special coverage. • A maximum of 1-hour is allowed to diagnose a defective component. • A maximum of 1-hour is allowed for retrieval of parts not in stock. • A maximum travel distance of 100 miles round trip and 2-hours will be reimbursed. • Overtime, installation/start-up, normal control adjustments, general maintenance, glass breakage, freight damage, and/or correcting and end-user installation error will not be reimbursed under warranty unless pre-approved with a Service Work Authorization from Delfield. You must submit the number with the service claim. Labor Of 1-Hour Is Allowed To Replace: • Thermostat • Contactor/Relay • Infinite Switch • Transformer • Door Jamb Switch • Evaporator/Condenser Fan Motor and Blade • Solenoid Coil • Circulating Fan Motor and Blade • Hi-limit/Thermal Protector Switch • Microprocessor Control • Fan Delay/Defrost Termination Switch • Water Level Sensor/Probe • Compressor Start Components and Overload Protector • Door Hinges, Locks, and Gaskets • Defrost Timer • Condensate Element • Thermometer • Springs/Lowerator • Gear Box Labor Of 2 Hours To Replace: • Drawer Tracks/Cartridges • Defrost Element • Pressure Control • Heating Element • Solenoid Valve • Locate/Repair Leak Labor Of 3 Hours To Replace: • EPR or CPR Valve • Condenser or Evaporator Coil • Expansion Valve Labor Of 4 Hours To Replace: • Compressor This includes recovery of refrigerant and leak check. $55.00 maximum reimbursement for refrigerant recovery (includes recovery machine, pump, torch, oil, flux, minor fittings, solder, brazing rod, nitrogen, or similar fees.) Refrigerants: • R22 A maximum of $4.00/lb. or 25¢/oz. will be reimbursed. • R134A A maximum of $5.00/lb. or 31¢/oz. will be reimbursed. • R404A A maximum of $16.00/lb. or $1.00/oz. will be reimbursed.

For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com 25

F18 Series Service and Installation Manual For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com 26Notes Notes F18 Series Service and Installation Manual 27 For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, delfield.com

Covington, TN Mt. Pleasant, MI

Thank you for choosing Delfield! Help is a phone call away. Help our team of professional, courteous customer service reps by having your model number and serial number available at the time of your call (800) 733-8829. Model: _______________________ S/N: ______________________ Installation Date: _______________ For a list of Delfield’s authorized parts depots, visit our website at delfield.com 980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (989) 773-7981 or (800) 733-8829 • Fax (989) 773-3210 • delfield.com Delfield reserves the right to make changes in design or specifications without prior notice. ©2013 The Delfield Company. All rights reserved. Printed in the U.S.A. DM18 07/13 9291454 Register your Delfield warranty online. Go to delfield.com under the service tab to complete.


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply