Click here to download DEGELMAN LANDROLLER LRX 46 (01) PDF MANUAL
PDF Content Summary:
****** Page 1 ****** Oegellflöll LANDROUER LRK LAØOLLEß LM51 LRK36141146151 DEGELMAN INDUSTRIES LTD. BOX 830-272 INDUSTRIAL DRIVE, REGINA, SK, CANADA, S 4 P 3B 1 FAX 306.543.2140 PH 306.543.4447 1.800. 667.3545 DEGELMAN.COM OPERATOR a PARTS MANUAL 743375 v7.o LANDROLLER LRX LRX 36/41/46/51
****** Page 3 ****** QUICK-START GUIDE* for LRX LANDROLLERS * Refer to operators manual for complete safety and operation info. Oegelman REMEMBER! You must complete Product Registration to be eligible for Warranty. A Connect Hydraulics O LATCH & END WHEELS….Latch & End Wheel Cylinders O SWING ARM CIRCUIT Power-fold Cylinders @ CTR WHEEL & FLOAT….Hitch & Center Wheel Cylinders B Opening into Field Position 1) Drive the LRX Landroller onto an area of level ground large enough to open the wings. Ensure the Landroller is positioned straight behind the tractor. 2) Remove the four Red Transport Bars from the End Wheel & Center Wheel cylinders. Place the transport bars onto 6) Retract the Center Frame Cylinders to raise the center frame wheels (lowering the center section to the ground). lock-pins. Ies Note: You may need to activate (extend) the hydraulic cylinders slightly to allow easier removal of the cylinder Transport Bars. 3) Activate the End Wheel Cylinders O to completely raise the end wheels and lower the ends of the drums to the ground. .e O 3 7) Remove the Red Transport Pin from the float hitch and secure it in storage position. 8) Open the Hydraulic Ball Valve. 9) Retract the Hitch Cylinder O 8 1. 9 7 4) Extend the Power-fold Cylinders@ to fully open the wings. Ensure the swing-arm shafts properly latch into place. 4 4 5) A IMPORTANT: Retract the POWER-FOLD Cylinders Remember to retract the Power-fold Cylinders @ back into the fully closed position before use. to place the Landroller into Float Position. 10) The LRX Landroller should now be in the proper position for field use. Read manual for further information. (Refer to operators manual for complete safety and operation info.) Maintenance (Check Machine Daily) • Check for missing, worn or damaged parts. • Working points & pins Hydraulic Connections & Hoses • Hubs & Spindles 143376 VI.’
****** Page 4 ****** C Moving Into Transport Position 1) Drive the LRX Landroller onto an area of level ground with plenty of room to drive straight forward. 2) Fully extend the Front Hitch & Center Frame Cylinders.@ This places the float hitch into Transport Position and also fully lowers the Center Frame Wheels (raising the center section off the ground). 3) A IMPORTANT: • Secure the Float Hitch in place with the Red Transport Pin. • Close the Hydraulic Ball Valve. 4) Completely extend the End Wheel & Latch Cylinders the End Wheels and open the Swing-Arm Latches. to lower 5) A IMPORTANT: Ensure the POWER-FOLD Cylinders are RETRACTED (closed) Ensure that the Power-fold Cylinders have been fully retracted before moving forward. Failure to do so could damage the Power-Fold cylinders and require replacement. 6) Drive forward until roller wings trail straight behind tractor. 7) Install the four Red Transport Bars onto the End Wheel & Center Wheel cylinder shafts and secure in place using the lock-pins. Ensure front Red Transport Pin has also been installed correctly into the float hitch (refer to step 3). 8) Read and follow necessary safety procedures outlined in Transport Safety section of the manual.
****** Page 5 ****** LRK36141146151 * Reference Sheet Quick-Start Guide OPERATORS SECTION – TABLE OF CONTENTS Introduction Safety Operation Pre-Operation Checklist Hook-Up / Transport Safety Transport to Field Position Field to Transport Position Service & Maintenance Maintenance Checklist and Specifications Repair – Hydraulic Cylinder Repair Repair – Pressed Bushing Repair – Wheel Hub Decal Location Overview Troubleshooting PARTS SECTION – TABLE OF CONTENTS Part Assemblies & Components Hitch Pole Frame Components Power-fold & Latch Components Center Frame Components Center Wheel Components Wing Frame Components End Wheel Frame Components Hydraulic Routing Hydraulic Routing – Latch & End Wheels Hydraulic Routing – Power-fold System Hydraulic Routing – Center Wheels & Float Electrical Layout & Light Components Warranty DEGELMAN INDUSTRIES LTD. BOX 830-272 INDUSTRIAL DRIVE, REGINA, s K, CANADA, S 4 P 3B 1 FAX 306.543.2140 PH 306.543.4447 1.800. 667.3545 DEGELMAN.COM 2 4 5 6 7 8 9 12 13 74 16 17 78 20 27 22 23 25 26 27 A IMPORTANT: READ MANUAL
****** Page 7 ****** Introduction LRK3614114G151 CONGRATULATIONS on your choice of a Degelman Landroller to complement your farming operation. It has been designed and manufactured to meet the needs of a discerning agricultural market for increasing yields for high quality pulse crops and preparing the perfect bed for haying, grasses and silage. Degelman rollers provide a smooth and level surface for faster, easier harvest operations and better seed-to-soil contact. Use this manual as your first source of information about this machine. TO THE NEW OPERATOR OR OWNER – Safe, efficient and trouble free operation of your Degelman Landroller requires that you and anyone else who will be operating or maintaining it, read and understand the Safety, Operation, Maintenance and Troubleshooting information contained within this manual. By following the operating instructions in conjunction with a good maintenance program your machine will provide many years of trouble-free service. Keep this manual handy for frequent reference and to pass on to new operators or owners. Call your Degelman Dealer if you need assistance, information, or additional copies of the manual. (3 RH SIDE RH Wins Roller Assembly LH Wing Frame LH SIDE Center Frame .31 i ROGER Hitch Pole Frame Front Hitch OPERATOR ORIENTATION – The directions left, right/ front and rear, as mentioned throughout the manual, are as seen from the tractor drivers’ seat and facing in the direction of travel. 143375 – LANDROLLER LRX (17-February-2017)
****** Page 8 ****** Safety why is SAFETY important to YOU? 3 BIG Reasons: •Accidents Can Disable and Kill •Accidents Are Costly •Accidents Can Be Avoided SAFETY ALERT SYMBOL The Safety Alert Symbol identifies important safety messages applied to the equipment and in this manual. When you see this symbol, be alert to the possibili of iniury or death. Follow the instructions provide on the safety messages. SIGNAL WORDS The Safety Alert Symbol means: ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Note the use of the Signal Words: DANGER, WARNING, and CAUTION with the safety messages. The appropriate Signal Word has been selected using the following guidelines: WARNING A CAUTION 143375 – LANDROLLER LRX (17-February-2017) DANGER: Indicates an imminently hazardous situation that, if not avoided, WILL result in death or serious injury if proper precautions are not taken. WARNING: Indicates a potentially hazardous situation that, if not avoided, COULD result in death or serious injury if proper precautions are not taken. CAUTION: Indicates a potentially hazardous situation that, if not avoided, MAY result in minor or moderate injury if proper practices are not taken, or, serves as a reminder to follow appropriate safety practices. -2-
****** Page 9 ****** Safety SAFETY YOU are responsible for the safe operation and maintenance of your equipment. YOU must ensure that you and anyone else who is going to operate, maintain or work around the equipment be familiar with the operating and maintenance procedures and related safety information contained in this manual. Remember, YOU are the key to safety. Good safety practices not only protect you but also the people around you. Make these practices a working part of your safety program. Be certain that EVERYONE operating this equipment is familiar with the recommended operating and maintenance procedures and follows all the safety precautions. Most accidents can be prevented. Do not risk injury or death by ignoring good safety practices. • Equipment owners must give operating instructions to operators or employees before allowing them to operate the equipment, and at least annually thereafter per OSHA regulation 1928.51. • The most important safety device on this equipment is a SAFE operator. It is the operator’s responsibility to read and understand ALL Safety and Operating instructions in the manual and to follow these. All accidents can be avoided. • A person who has not read and understood all operating and safety instructions is not qualified to operate the machine. An untrained operator exposes himself and bystanders to possible serious injury or death. • Do not modif the equipment in any way. Unauthorize modification may impair the function and/or safety and could affect the life of the equipment. • Think Safety! Work Safely! 143375 – LANDROLLER LRX (17-February-2017) GENERAL SAFETY 1. 2. 3. 4. 7. 9. -3- Read and understand the Operator’s Manual and all safety signs before operating, maintaining or adjusting. Install and properly secure all shields and guards before operating. Use hitch pin with a mechanical locking device. Have a first-aid kit available for use should the need arise and know how to use it. Have a fire extinguisher available for use should the need arise and know how to use it. 5. Wear appropriate protective gear. This list includes but is not limited to: • A hard hat • Protective shoes with slip resistant soles • Protective glasses or goggles • Heavy gloves • Wet weather gear • Hearing protection • Respirator or filter mask 6. Clear the area of people, especially small children, and remove foreign objects from the machine before starting and operating. Do not allow riders. 8. Stop tractor engine, set park brake, remove ignition key and wait for all moving parts to stop before servicing, adjusting, repairing or unplugging. Review safety related items with all operators annually.
****** Page 10 ****** Operation •ro THE NEW OPERATOR OR OWNER The Degelman Landroller is designed to provide a smooth and level surface. It is the responsibility of the owner or operator to read this manual carefully to learn how to operate the machine safely. Safety is everyone’s business. By following safe operating practices, a safe environment is provided for the operator and bystanders. By following the operating instructions in conjunction with a good maintenance program your machine will provide many years of trouble-free service. Trans ort Position Front Hitch Frame Center Frame OPERATING SAFETY 1 . Read and understand the Operator’s Manual and all safety signs before using. 2. Stop tractor engine, set park brake, remove ignition key and wait for all moving parts to stop before servicing, adiusting, repairing or unplugging. 3. Keep hands, feet, hair and clothing away from all moving and/or rotating parts. 4. Do not allow riders on the Landroller tractor during operation or transporting. 5. Keep all shields and guards in place when operating (if applicable). 6. Clear the area of all bystanders, especially children, before starting. Do not operate machine on overly steep side 7. hills or slopes. 8. Be careful when working around or maintaining a high-pressure hydraulic system. Ensure all components are tight and in good repair before starting. 9. Clean all reflectors, lights and the SMV sign before transporting on a highway or public road. Be sure to check with local highway authorities and comply with their lighting Power-fold Cylinder Cross Joint Power-fold Swing Arm Truss Arm LH Wing Frame requirements. Field Position Front Hitch Center Frame Swing Arm Power-fold Latch RH Wing Frame End Wheel wheels Cross Joint End Wheel Cylinder End Wheel Strut 143375 – LANDROLLER LRX (17-February-2017) -4-
****** Page 11 ****** Operation BREAK-IN Although there are no operational restrictions on the Landroller when it is new, there are some checks that should be done when using the machine for the first time, follow this procedure: IMPORTANT: It is important to follow the Break-ln procedures especially those listed in the “Before using” section below to avoid damage: A. Before using: 1 . Read Safety Info. & Operator’s Manual. 2. Complete steps in UPre-Operation Checklis€’. 3. Check all bolt tightness. B. After operating for 2 hours: 1 . Check all hardware. Tighten as required. 2. Check all hydraulic system connections. Tighten if any are leaking. C. After operating for 8 hours: 1 . Repeat Step B. 2. Go to the service schedule as outlined in the “Service & Maintenance” section. 143375 – LANDROLLER LRX (17-February-2017) PRE-OPERATION CHECKLIST It is important for both personal safety and maintaining good operational condition of the machine that the pre-operational checklist be followed. Before operating the machine and each time thereafter, the following areas should be checked off: Lubricate the machine per the schedule outlined in the “Maintenance Section”. Use only a tractor with adequate power to pull the Landroller under ordinary operating conditions. Ensure that the machine is properly attached to the tractor using a drawbar pin with provisions for a mechanical retainer. Make sure that a retainer such as a Klik pin is installed. NOTE: It is important to pin the draw bar in the central location only. Before using, inflate tires to: Center & End Wheel Tires – LRX x15- 12 PLY: 90 PSI (620 kPa) Ensure that a safety chain is installed on the hitch. Check oil level in the tractor hydraulic reservoir. Top up as required. Inspect all hydraulic lines, hoses, fittings and couplers for tightness. Tighten if there are leaks. Use a clean cloth to wipe any accumulated dirt from the couplers before connecting to the tractor’s hydraulic system. -5-
****** Page 12 ****** Operation HOOK-UP / UNHOOKING The Landroller should always be parked on a level, dry area that is free of debris and foreign objects. Follow this procedure to hook-up: I . Clear the area of bystanders and remove foreign objects from the machine and working area. 2. Make sure there is enough room to back the tractor up to the trailer hitch. 3. Start the tractor and slowly back it up to the hitch point. A DANGER FRAME PINCH POINTS & CRUSHING HAZARDS Can cause serious injury or death. • Stay Of during and • persons while any part of this machigw is motion. 4. Stop the tractor engine, place all controls in neutral, set park brake and remove ignition key before dismounting. 5. Use the jack to raise or lower the hitch to align with the drawbar. 6. Install a drawbar pin with provisions for a mechanical retainer such as a KLIK pin. Install the retainer. 7. Install a safety chain between the tractor and the hitch. 8. Connect the hydraulics. To connect, proceed as follows: • Use a clean cloth or paper towel to clean the couplers on the ends of the hoses. Also clean the area around the couplers on the tractor. Remove the plastic plugs from the couplers and insert the male ends. • Be sure to match the pressure and return line to one valve bank. 9. Connect lights (electrical socket plug) to tractor. 10. Raise the hitch jack and rotate it 900 to place in its stowed position. I I . When unhooking from the tractor, reverse the above procedure. 143375 – LANDROLLER LRX (17-February-2017) TRANSPORT SAFETY I . Read and understand ALL the information in the Operator’s Manual regarding procedures and SAFETY when operating the Landroller in the field/ yard or on the road. 2. Check with local authorities regarding machine transport on public roads. Obey all applicable laws and regulations. 3. Always travel at a safe speed. Use caution when making corners or meeting traffic. 4. Make sure the SMV (Slow Moving Vehicle) emblem and all the lights and reflectors that are required by the local highway and transport authorities are in place, are clean and can be seen clearly by all overtaking and oncoming traffic. 5. Keep to the right and yield the right-of-way to allow faster traffic to pass. Drive on the road shoulder, if permitted by law. 6. Always use hazard warning flashers on tractor when transporting unless prohibited by law. 7. Always use a pin with provisions for a mechanical retainer and a safety chain when attaching to a tractor or towing vehicle. TRANSPORTING Use the following guidelines while transporting the Landroller: 1. Use a safety chain. 2. Ensure all transport locks are securely in place. 3. Be sure hazard lights are flashing and SMV decal is visible. 4. MAXIMUM RECOMMENDED TRANSPORT SPEED: 30 km/h or 1 9 mph. (Road Conditions. Field speeds may be lower.) A IMPORTANT: UNDER NO CIRCUMSTANCES SHOULD THERE EVER BE RIDERS WHILE THE LÄNDROLLER IS IN TRANSPORT. NO RIDERS -6-
****** Page 13 ****** Operation TRANSPORT TO FIELD POSITION I . Drive the LRX Landroller onto an area of level ground large enough to open the wings. Ensure the Landroller is positioned straight behind the tractor. IMPORTANT 2. Remove the four Red Transport Bars from the End Wheel & Center Remove red bar rnachjne. Replace Wheel cylinders. Place the transport bars onto the frame mounted III taut retiree la barre avant d’opeet la storage brackets and secure with lock-pins. Note: You may need to activate (extend) the 6. Retract the Center Frame Cylinders to raise the center frame wheels (lowering the center section to the ground) 7-1, 7. hydraulic cylinders slightly to allow easier removal of the cylinder Transport Bars. 3. Activate the End Wheel Cylinders to completely raise the End Wheels and lower the ends of the LRX51 drums to the ground. 4. Extend the Power- Remove the Red Transport Pin from the float hitch and secure it in storage position. 8 9 3 fold Cylinders to fully open the wings. Ensure the swing-arm shafts properly latch into place. 8. Open the Hydraulic Ball Valve. IMPORTANT Valve must be Ban Valve be OPEN cwseo in TRANSPORT 9. Retract the Hitch Cylinder to place the Landroller into Float Position. 10. The LRX Landroller should 7 IMPORTANT HITCH Cylinder Circuit must be in FLOAT position when operating in the FIELD. Le Circuit Hydraulique de Ia barre de tire devrait etre en position flottante lors des operations au champs. 4 4 5. A IMPORTANT: 4 3 now be in the proper position for field use. 3 Retract the POWER-FOLD Cylinders Remember to retract the Power- fold Cylinders back into the fully closed position before use. IMPORTANT Fully RETRACT the POWER FOLD Cylinders after wings are latched into Field Position. 143375 – LANDROLLER LRX (10-May-2017)
****** Page 14 ****** Operation FIELD TO TRANSPORT POSITION I . Drive the LRX Landroller onto an area of level ground with plenty of room to drive straight forward. 2. Fully extend the Front Hitch & Center Frame Cylinders. This places the float hitch into Transport Position and also fully lowers the Center Frame Wheels (raising the center section off the ground). 3. A IMPORTANT: • Secure Float Hitch in place with the Red Transport Pin. • Close the Hydraulic Ball Valve. IMPORTANT Ban Valve must be Valve must OPEN in CLOSED in TRANSPORT position. 3 2 3 4. Completely extend the End Wheel & Latch Cylinders to lower the End Wheels and open the Swing-Arm Latches. 4 4 4 143375 – LANDROLLER LRX (10-May-2017) 5) A IMPORTANT: Ensure POWER-FOLD Cylinders are RETRACTED (closed) Ensure that the Power-Fold Cylinders have been fully retracted before moving forward. Failure to do so could damage the Power-Fold cylinders and require replacement. 6. Drive forward until roller wings trail straight behind tractor. 5 6 11 7. Install the four Red Transport Bars onto the IMPORTANT Ranove transport bar before operating nuchine. Replace II taut la rouge avant d•opeer machine, La rewet’tre en place avant de la End Wheel & Center Wheel cylinder shafts and secure in place using the lock-pins. Ensure front Red Transport Pin has also been installed correctly in to the float hitch (refer to step 3). 8. -8- Read and follow necessary safety procedures outlined in Transport Safety section of the manual.
****** Page 15 ****** Service & Maintenance MAINTENANCE SAFETY 1 . Review the Operator’s Manual and all safety items before working with/ maintaining or operating the LRX Landroller. 2. Stop the tractor engine, set park brake, remove ignition key and wait for all moving parts to stop before servicing, adiusting, repairing or unplugging. 3. Keep hands, feet, clothing and hair away from all moving and/or rotating parts. 4. Clear the area of bystanders, especially children, when carrying out any maintenance and repairs or making any adjustments. 5. Place safety stands or large blocks under the frame before removing tires or A DANGER FRAME PINCH POINTS & CRUSHING HAZARDS Can cause serious iinJury death. •Stay Clear Of rn.Et’ine during • all persons clear while any part Ot this machine is in motion. working beneath the machine. 6. Be careful when working around or maintaining a high-pressure hydraulic system. Wear proper eye and hand protection when searching for a high pressure hydraulic leak. Use a piece of wood or cardboard as a backstop when searching for a pin hole leak in a hose or a fitting. 7. Always relieve pressure before disconnecting or working on hydraulic system. 143375 – LANDROLLER LRX (17-February-2017) MAINTENANCE CHECKLIST After reviewing the Maintenance and Hydraulic Safety Information, use the Maintenance Checklist provided for regular service intervals and keep a record of all scheduled maintenance: ( Initial break-in review. ) A. Before using: 1 . Read Safety Info. & Operator’s Manual. 2. Complete “Pre-Operation Checklis(‘ 3. Check all Bolt Tightness. B. After operating for 2 hours: 1 . Check all hardware. Tighten as required. 2. Check all hydraulic system connections. Tighten if any are leaking. Maintenance Check – 10 Hours e Check for worn or damaged parts Hydraulic fluid leaks e Damaged hoses e Check tire pressure: LRX – Center Frame & End Wheel Tires 12 PLY: 90 PSI (620 kPa) Maintenance Check – 50 Hours e Grease hubs & spindles e Check working points & pins • Safety signs clean Annually • Bolt tightness • Wheel bearings e Latch mechanism -9-
****** Page 16 ****** Service & Maintenance o HARDWARE SPECIFICATIONS Note: Unless stated otherwise, hardware is typically: Hex, Plated GR5 UNC or P8.8 (metric) TORQUE SPECIFICATIONS Checking Bolt_Torque o- TORQUE The tables below give correct torque values for various bolts and capscrews. Tighten all bolts to the torques specified in chart unless otherwise noted. Check the tightness of bolts periodically, using these bolt torque charts as a guide. Replace hardware with the same strength (Grade/Class) bolt. IMPERIAL TORQUE SPECIFICATIONS (Coarse Thread – based on “Zinc Plated” values) Size 5/16″ 3/8″ 7/16″ 1/2″ 9/16″ 5/8″ 7/8″ 1-1/8″ 1-3/8″ 1-1/2″ o SAE-5 Grade 5 lb.ft (N.m) 7 (70) 15 (20) 25 (35) (55) 65 (90) 90 (725) 130 (175) 230 (310) 365 (495) 550 (745) 675 (975) 950 (1290) 1250 (7695) 1650 (2245) o SAE-8 Grade 8 lb.ft (N.m) 10 (14) 20 (28) 35 (50) 60 (80) 90 (720) 130 (175) 180 (245) 320 (435) 515 (700) 770 (1050) 1095 (7485) 1 545 (2095) 2025 (2745) 2690 (3645) METRIC TORQUE SPECIFICATIONS (Coarse Thread – based on “Zinc Plated” values) Size M8 MIO M12 M14 M16 M18 M20 M22 M24 M27 M30 M33 M36 o Class 8.8 lb.ft (N.m) 7 (10) 16 (22) 30 (42) 55 (75) 90 (120) 135 (785) 190 (255) 265 (360) 365 (495) 460 (625) 675 (915) 915 (1240) 1250 (7695) 1600 (2775) o class 10.9 lb.ft (N.m) 10 (14) 23 (31) 45 (60) 80 (108) 125 (770) 195 (265) 270 (365) 380 (515) 520 (705) 660 (895) 970 (1315) 1310 (1780) 1785 (2420) 2290 (3110) HYDRAULIC SAFETY Make sure that all components in the hydraulic system are kept in good condition and are clean. Replace any worn, cut, abraded, flattened or crimped hoses and metal lines. Do not attempt any makeshift repairs to the hydraulic lines, fittings or hoses by using tape, clamps or cements. The hydraulic system operates under extremely high-pressure. Such repairs will fail suddenly and create a hazardous and unsafe condition. Wear proper hand and eye protection when searching for a high-pressure hydraulic leak. Use a piece of wood or cardboard as a backstop instead of hands to isolate and identify a leak. If injured by a concentrated high-pressure stream of hydraulic fluid, seek medical attention immediately. Serious infection or toxic reaction can develop from hydraulic fluid piercing the skin surface. Before applying pressure to the system, make sure all components are tight and that lines, hoses and couplings are not damaged. o HYDRAULIC HOSE SPECIFICATIONS Note: Unless otherwise stated, Hydraulic Hoses are either 3/8 or 1 / 2 with 3/4 JIC female swivel ends. HYDRAULIC HOSE INSTALLATION TIPS The following tips are to help you identify some possible problem areas in the installation of hydraulic hoses. 1 . Ensure hoses are not twisted during installation as this may weaken the hose. Also, the pressure in a twisted hose may loosen fittings or connections. 2. Allow sufficient bend radius in hoses when installing to prevent lines from collapsing and flow becoming restricted. 3. When installing hoses in an area of movement or flexing, allow enough free length for motion and to ensure fitting connections are not stressed. 4. Ensure hoses are properly clamped and secured in position after routing is complete to provide a cleaner installation and prevent possible damage or hazards. 143375 – LANDROLLER LRX (17-February-2017) -10-
****** Page 17 ****** Service & Maintenance HYDRAULIC FITTING INSTALLATION The following info is to help you identiY and properly install some of our standard hydraulic ittings. SAE (JIC) 370 Flare JIC fittings – Metal-to-metal sealing type fittings featuring a 370 flare (angle of sealing surface) and straight UNF (United National Fine) Threads. (Lubricated Dash Thread Size Torque – lb.ft (N.m) -9 Note: A DASH size refers to a diameter of a hose (inside) or of a tube (outside) measured in 1 / 1 6″ increments. For example, a Hose specified as dash 8 or -8 would have an inside diameter of 8/16″ or 1/2″ Alternatively, a Tube specified as dash 8 or -8 would have an outside diameter of 8/16″ or / 2″. Values) -4 -6 -8 -10 -12 7/16 – 20 9/16 – 18 3/4- 16 7/8- U 1-1/16 – 12 9-12 14-20 27-39 36-63 65-88 (12-16) (19-27) (37-53) (50-85) (90-119) ORB (O-Ring Boss) Male ORB fittings have straight UNF threads, a sealing face and an O-ring. The female fittings are generally found in the ports of machines and feature straight threads, a machined surface, and a chamfer to accept the O-ring. Sealing is achieved through the compression of the male O-ring against the chamfered sealing face of the female fitting. Torque Torque (Lubricated Dash Thread Size Non-Adiustable Adiustable Tightening JIC 370 Flare Type Fittings 1 . Check flare and flare seat for defects that might cause leakage. 2. Align fittings before tightening. Lubricate connections & hand tighten swivel nut until snug. 3. Using two wrenches, torque to values shown in table. Values) -4 -6 -8 -10 -12 7/16 – 20 9/16 – 18 3/4- 16 1-1/16 – 12 lb.ft (N.m) 30 (40) 35 (46) 60 (80) 100 (735) 135 (185) lb.ft (N.m) 15 (20) 35 (46) 60 (80) 100 (135) 135 (185) Alternate Installation Method 3. Using two wrenches. Place one wrench on the fixed connector body at a clock position of 6 0’clock. 4. Place the second wrench on the second connection as close to the 3 0’clock position as possible. 12 11 10 1 2 O 3CO 8 5 MIN 5. Tighten by rotating the MAX second connection firmly to at least the 4 0’clock position, but no more than the 7 0’clock position. Typically, the larger the fitting size the less rotation required. ORFS (O-Ring Face seal) ORFS fittings use an O-ring compression method to seal. This method offers a high level of sealing along with good vibration resistance. Male fittings include an O-ring located in a groove on the flat face. Female fittings feature a flat face and UNF straight threaded swivel nut. The Torque method is recommended for ORFS installation. Dash -4 -6 -8 -10 -12 Thread Size Torque – lb.ft (N.m) 9/16 – 18 11/16 – 16 13/16 – 16 1-3/16 – 12 18 (25) 30 (40) (55) 60 (80) 85 (115) Tightening ORFS (O-Ring Face Seal) Fittings 1 . Inspect components and ensure the O-Ring seal is undamaged and properly installed in the groove of the face seal. Replacing the O-Ring may be necessary. 2. Align, thread into place and hand tighten. 3. Tlghten to proper torque from the table shown above. 143375 – LANDROLLER LRX (17-February-2017) Tightening ORB (O-Ring Boss) Fittings Non-adjustable Port End Assembly I . Inspect the components to ensure that male and female threads and sealing surfaces are free of nicks, burrs, scratches, or any foreign material. 2. Ensure O-Ring seal is properly installed and undamaged. 3. Lubricate threads and O-ring to help the O-ring slide past the port entrance corner and avoid damaging it. 4. Screw the fitting into position tighten to proper torque value from the table shown above. Adjustable Port End Assembly Lock Nut I . Inspect the components to ensure Bac -up male & female threads and sealing Washer surfaces are free of nicks, burrs, -Rin scratches, or any foreign material. 2. Ensure O-Ring seal is properly installed and undamaged. 3. Lubricate threads and O-ring to help the O-ring slide smoothly into the port and avoid damage. 4. Loosen back the lock nut as far as possible. Make sure back-up washer is not loose and is pushed up as far as possible. 5. Screw the fitting into port until the back-up washer or the retaining ring contacts face of the port. Light wrenching may be necessary. Over tightening may damage washer. 6. To align the end of the fitting to accept incoming tube or hose assembly, unscrew the fitting by the required amount, but not more than one full turn. 7. Using two wrenches, hold the fitting in desired position and tighten the locknut to the proper torque value from the table located above. 8. Inspect to ensure that O-ring is not pinched and that washer is seated flat on the face of the port. -11-
****** Page 18 ****** Service & Maintenance HYDRAULIC CYLINDER REPAIR PREPARATION When cylinder repair is required, clean off unit, disconnect hoses and plug ports before removing cylinder. When removed, open the cylinder ports and drain the cylinder’s hydraulic fluid. 1 1/8- 12 UNF 1 1/2- 12 UNF 1 3/4 – 12 UNF REPAIRING A THREADED HEAD CYLINDER Set Screw Style Barrel Gland Set Screw End Cap Examine the type of cylinder. Make sure you have the correct tools for the job. You may require the following tools: • Proper Seal Kit • Allen Key Set • Emery cloth • Torque Wrench Threaded Head Cylinder (Monarch) Set Screw Threaded Head U-cup Wear Dual Seal Ring Wiper Seal Wear Ring Piston DISASSEMBLY Rod Assembly CYLINDER ROD LOCKNUT TORQUE VALUES O.D. Threads = Locknut Size LOCKNUT SIZE (PISTON) TORQUE VALUE 3/8 24 UNF 1/2 – 20 UNF 5/8 – 18 UNF 3/4 – 16 UNF 7/8 – 14 UNF 1 – 14 UNF – 12 UNF 25-30 lb.ft 40-60 lb.ft 95-105 lb.ft 175-225 lb.ft 200-275 lb. ft 300-380 lb.ft 400-500 lb. ft 500-600 lb.ft 700-800 lb.ft 800-900 lb.ft (35-42 N.m) (55-80 N.m) (130-140 N.m) (240-305 N.m) (270-370 N.m) (405-515 N.m) (540-675 N.m) (675-810 N.m) (950-1085 N.m) (1085-1220 N.m) 143375 – LANDROLLER LRX (17-February-2017) 1. Loosen Set Screw and turn off end cap. 2. Carefully remove piston/rod/gland assemblies. 3. Disassemble the piston from the rod assembly by removing lock nut. NOTE: DO NOT clamp rod by chrome surface. 4. Slide off gland assembly & end cap. 5. Remove seals and inspect all parts for damage. 6. Install new seals and replace damaged parts with new components. 7. Inspect the inside of the cylinder barrel/ piston, rod and other polished parts for burrs and scratches. Smooth areas as needed with an emery cloth. REASSEMBLY 1. Reinstall rod through end cap & gland assembly. 2. Secure piston to rod with lock nut. Torque lock nut to proper value (refer to chart for proper torque value). 3. Lube inside of barrel, piston seals, and gland seals with hydraulic oil. 4. With cylinder body held gently in a vise, insert piston, gland, end cap and rod combination using a slight rocking motion. 5. Apply Loctite anti-seize before installing cylinder end cap. 6. Torque cylinder end cap to 440 lb.ft (600 N.m). 7. Tighten Set Screw on end cap to 6 lb.ft (8 N.m). -12-
****** Page 19 ****** Service & Maintenance REPLACING A PRESSED BUSHING NOTE: You may need the following tools: Press, hammer, punch, pry-bar, IfStep-Tool’I Use the following as a guideline for repair: 1. Ensure the area and frame are properly secured, supported, and safe to work on. Safely remove the pin(s), cylinder, and/or components necessary in order to access and work on the damaged bushing. 2. Remove the existing bushing using required tools. In some instances, you may need to cut the damaged bushing in order for easier removal (use proper safety precautions and try not to damage other components if using this method). 3. With the bushing removed, clean and prepare the location for the new bushing insert. Note: It is recommended to use a mixture of “Dish Soap and Water” as a lubricant on the outside of the composite bushing. IMPORTANT: DO NOT use oil or grease on outside or inside of composite bushings. 4. Use a stepped tool to ensure the edge of the bushing is not damaged when inserting. ADJUSTING POWER-FOLD LATCH CLOSURE NOTE: You may need the following tools: 3/8″ Allen/Hex Key, Blue Loctite Use the following as a guideline for repair: 1. Ensure the area and frame are properly secured, supported, and safe to work on. 2. Loosen the two 3/4″ setscrews that hold the adjustable shaft in position. 3. Adiust the shaft by rotating it in the required direction to allow a better latch alignment. 4. When satisfied with the alignment, re-install the two setscrews and tighten. IMPORTANT: It is recommended to add blue Loctite to the setscrew threads before reinstalling. Stepped Tool Bushing Housing Press (recornmended) or Hammer (to 5/16 depth) Adiustable Eccentric Shaft IMPORTANT: Add Blue Loctite to setscrew threads. Note: YOU may need to adiust the rotation of the Eccentric (Offset) Shaft if proper latch closure becomes difficult. (3/8″ Allen/Hex Key Required) 1 17600 – Setscrew, Allen (2) 242672 – Offset Shaft 5. Ensuring the bushing is properly aligned, press into hole (preferred method) or hammer into position by striking the stepped tool. 6. Continue to install until the bushing edge is recessed in to a distance of 5/16″ to allow for the outer seal to be properly installed. Do not exceed this depth. 7. Repeat procedure for bushing on opposite side. 8. When both bushings are installed Install to the proper depth, install new Seal seals. 9. Re-assemble all other necessary 5/16″ components. 143375 – LANDROLLER LRX (17-February-2017) -13-
****** Page 20 ****** Service & Maintenance WHEEL HUB REPAIR DISASSEMBLY 1. Remove dust cap. WHEEL NUT & WHEEL BOLT TORQUE BOLT PATTERNS A IMPORTANT: Be sure to block up unit securely before removing tires. O 3 4 o 5 2 5 BOLT PATTERN 4 o o 5 3 o 2 6 BOLT PATTERN 1 8 2 8 BOLT PATTERN TORQUE 8 10 000 30 5 o O 4 ooo 7 2 10 BOLT PATTERN 2. Remove cotter pin from nut. 3. Remove nut and washer. 4. Pull hub off spindle. 5. Dislodge the inner cone bearing and dust seal. 6. Inspect cups that are press fitted into hub for pits or corrosion and remove if necessary. 7. Inspect and replace defective parts with new ones. ASSEMBLY If cups need replacing, be careful to install them gently and evenly into hub until they are fully seated. 2. Apply a thick wall of grease inside hub. Pack grease in cones. 3. Install inner cone and dust seal as illustrated. 4. Position hub onto spindle and fill surrounding cavity with grease. 5. Assemble outer cone, washer COMMON HUB & SPINDLE COMPONENTS Spindle Dust Seal Inner Cone Inner Cup Hub Wheel Not/ Bolt Torque lb.ft (N.m) Size 9/16 120-130 (165-175) 5/8 185-190 (250-260) 3/4 280-300 (380-405) Wheel Tightening Procedure 1. Install and hand tighten nuts/bolts. and nut. Outer Cup 6. Tighten nut while rotating hub until there is a slight drag. Outer Cone 7. Turn nut back approximately 1/2 turn to align cotter pin hole with notches on nut. 8. Install cotter pin and bend legs sideways over nut. 9. Fill dust cap half full of grease and gently tap into position. Flat Washer Slotted Nut & Cotter Pin Dust Cap 10. Pump grease into hub through grease fitting until lubricant can be seen from dust seal. 143375 – LANDROLLER LRX (17-February-2017) 2. Tighten to approx. 20% Torque value using the Bolt Star or CrissCross patterns shown above. 3. Tighten to Full Torque value using the Star or CrissCross pattern. 4. If applicable, install Rear Locknuts using Wheel Torque Values. -14-
****** Page 21 ****** Service & Maintenance DECAL LOCATION OVERVIEW (Both Sides) 142797 – Decal, LRX 51 (2) 742795 – Decal, LRX 46 (2) 142793 – Decal, LRX 41 (2) 142791 – Decal, LRX 36 (2) 143280 – Decal, Important – Float (l) 142992 – Decal, Important – Power-fold Cylinder (l) 142991 – Decal, Important – Ball Valve (1) 143162 – Decal, 142777 – Decal, Read Manual (1) Patent (1) 142990 – Decal, Hyd Hoses Label (l) LAND OLLEø LB*51 142387 – Decal, Important – Remove Red (l) 142796 – Decal, LRX 51 (2) 142794 – Decal, LRX 46 (2) (Both Sides) 142792 – Decal, LRX 41 (2) 742790 – Decal, LRX 36 (2) (Both Sides) 142993 – Decal, Danger – Pinch/Crush (2) 142556 – Decal, Reflector Red (Both Sides) -2×9 (2) 142993 – Decal, Danger – Pinch/Crush (1) 142994 – Decal, Caution/lmportant – Info (1) SAFETY DECALS & REFLECTORS Keep safe decals and signs clean and legible at all times. Rep ace safety decals and signs that are missing or have become illegible. Safety decals or signs are available from your Dealer Parts Department. 142556 – 142557 – 142650 – 142387 – 142991 – 142992 – 142993 – 142994 – 143280 – 142990 – 143162 142777 – 142008 – 142009 – 142796 – 142797 – 142794 – 142795 – 142792 – 142793 – 142790 – 142791 142557 – Decal, Reflector Amber – 2 x 9 (4) Decal, Reflector Red – 2 x 9 Decal, Reflector Amber – 2 x 9 Decal, Fluorescent Tape – 2 x 9 Decal, Important – Remove Red Decal, Important – Ball Valve Decal, Important – Power-fold Decal, Danger – Pinch / Crush Decal, Caution/lmportant – Info Decal, Important – Float Decal, Hydraulic Hose Label – Decal, Read Manual Decal, Patent Pending Decal, Degelman – 6m Decal, Degelman – 3-3/4″ (Both Sides) 142557 – Decal, Reflector Amber 142008 – Decal, Degelman (Both Sides) 142387 – Decal, Important – Remove Red (4) 142556 – Decal, Reflector Red -2 x 9 (2) -15- Decal, Decal, Decal, Decal, Decal, Decal, Decal, – Decal, LRX 51 -64 LRX 51 -4″ LRX 46 – 64 LRX 46-4″ LRX 41 – 64 LRX41 -4″ LRX 36 – 64 LRX 36 – 4″ (Both Sides – both wing frames) 142796 – Decal, LRX 51 (4) 742794 – Decal, LRX 46 (4) 142792 – Decal, LRX41 (4) 742790 – Decal, LRX 36 (4) 143375 – LANDROLLER LRX (Both Sides) 142650 – Decal, Fluorescent Tape – 2 x 9 (4) (Both Sides) 142009 – Decal, Degelman – 3-3/4″ (2) (Both Sides) 142797 – Decal, LRX 51 (2) 142795 – Decal, LRX 46 (2) 742793 – Decal, LRX41 (2) 142791 – Decal, LRX 36 (2) (24-March-2017)
****** Page 22 ****** Troubleshooting GENERAL TROUBLESHOOTING SYMPTOM Uneven ground contour, and more compaction on the center section of the Landroller. When driving in the field position, the wings fall back. One wing won’t open up into field position. PROBLEM The center hitch frame is not in the float position. When putting the Landroller into field position it is not latching correctly. Uneven ground or misaligned swing arm shaft. Landroller rollers won’t turn. Material build-up around rollers. If it is only one roller that doesn’t turn, it might be a SOLUTION Ensure that the Landroller float hitch frame has been fully opened and placed into the proper float position. Also ensure that the tractor’s hydraulic circuit for this Hitch Cylinder is in “Float”. Ensure the Landroller is on level ground when backing UP to the latch mechanism. Ensure that the swing-arm shafts fully engage into the latches. If problem still occurs, you may need to adiust the adiustable swing arm latch shaft to align properly. Ensure the Landroller is on level ground when backing UP to the latch mechanism. Ensure that the swing-arm shafts fully engage into the latches. If problem still occurs, you may need to adiust the adiustable swing arm latch shaft to align properly. Ensure that there is no material build-up around rollers. 143375 – LANDROLLER LRX faulty bearing. (17-February-2017) -16-
****** Page 23 ****** Hitch Pole / Front Frame Components Hose Holder Assembly Components 573165 – Hyd Hose Retainer Handle (1) comes with.. 572930 – Handle Grip 572937 – Ball, Pull Pin NOTE: Add Blue Loctite to threads 117580 – Bolt, 5/8 x 2-1/4 GR8 (5) 118537 – Flat washer, 5/8 – F436 (6) 118447 – Lock Nut, 5/8 Unitorque (5) 118105 – Bolt, 5/16 x 2-1/2 118144 – Bolt, 5/16 x 1-1/2 (3) 780279 – Top B Plate (l l) 780278 – Hose Clamp, 2 Halves (19) Front Hitch Pole Components 18911 – Lock Nut, I (2) 124012 – Front Hitch, CAT 4 (l) 117429 – Bolt, 1 x 7-1/2 UNC GR8 (2) 131020 – Flat washer, 1 F436 (4) 118073 -Bolt, 1 x 3-1/2 UNC GR8 (1) 118520 – Flat washer, I (l) 116302 – Safety Chain – 40,000 LB (1) 1 18615 – Flat washer, 1 x 3-1/8 x 1/4 (1) 118911 -Lock nut, 1 – GRC, Unitorq (1) “—242715 – Hose Holder Assembly (1) 133100 – Manual Holder (l) mounts with. 118123 -Bolt, 1/4x 1 (4) 118555 – Flat Washer, 1/4 (8) 18483 – Lock Nut, 1/4 – Unitorque (4) Cylinder Replacement Bushings Float Plate Components 118816 – Klik Pin, 7/16 (1) 242724 – Lock Pin, Float (1) 573341 – Pin Assembly, 2 x 7-9/16 (3) 118727 – Bolt, 7/8 x 2-1/2 GR8 (3) 118774 – B CE133135 – Wiper seal, 2-1/2 OD (4) 117225 – Bushing, 2-1/2 OD x 2 (4) 123215 – Cylinder, Monarch, 4 x 12 x 2 (2) (Seal Kit: 123049) 242705 – Float Plate Hitch (l) 117416 – Lock Nut, 7/8 Unitorq (3) Flat washer, 7/8 – F436 (6) (mounts to front 132051 – Jack, Sidewind (l) 242625 – Hitch Pole Assembly ( l) ¯ 17 _ center frame) B 117225 – Bushing, 2-1/2 OD x 2 (6) 133135 – Wiper seal, 2-1/2 OD (6) 143375 – LANDROLLER LRX (I I -September-2017)
****** Page 24 ****** Power-fold Swing Arm & Latch Components Power-fold Swing-Arm Component Overview 242693 – Threaded Pin Assembly (2) 242675 Floa (3/8″ Allen/Hex Key Required) IMPORTANT: Add Blue Loctite to setscrew threads. Note: Adjust Offset Shaft rotation during final assembly for proper : latch closure. 1 17600 – Setscrew, Allen (2) 242672 – offset Shaft (1) G. 242680 – Bushing) 242660 – Swing Arm Assembly RH (1) (shown) 242667 – Swing Arm Assembly – LH (7) (opposite) 131206 – Flat Washer, 1-1/4 F436 (2) 242659 – Collar, Autofold (2) 18126 – Bolt, 1/2 x4 (2) 118420 – Lock Nut, 1/2 (2) 123213 – Cylinder, Monarch, 4-1 / 2 x 20 x 2 (2) (Seal Kit: 123214) Cylinder Replacement Bushings 133135 – Wiper seal, 2-1/2 OD (4) 117225 – Bushing, 2-1/2 ODx2 (4) 118445 – Lock 1-1/4 (2) 242680 – Bushing, 5 OD (4) 242682 – Top cap Plate (4) 0—118504 – Lock washer, 1/2 (8) 118009 – Bolt, 1/2 x 1-1/4 (8) Power-fold Swing-Arm Latch Components 242710 – Latch Assembly (2) (comes with) 133135 – Wiper seal, 2-1/2 OD (2) 117225 – Bushing, 2-1/2 OD x 2 (l) 810280 – Retaining Ring, 1-1/4 242698 – Pin, 1-1/4 x 4-1/8 (2) 247449 – Pin, 1-1/4 x 4-1/2 247703 – Adiustment Rod, Latch (2) 123076 – Monarch, 143506 – Spring, Comp. (2) 118615 – Flat washer, I x 3-1/8 (2) 118456 – Lock NUt, I (2) 143375 – LANDROLLER LRX (17-February-2017) Cylinder, 2x4x 1-1/4 (2) (Seal Kit: 123061) -18-
****** Page 25 ****** Center Frame Components Center Frame Components 573342 – Pin ASSY, 2 x 8-5/16 (2) 118727 – Bolt, 7/8 x 2-1/2 GR8 (2) 242800 – Center Frame Assembly (1) 118105 – Bolt, 5/16 x 2-1/2 (3) 1 18144 – Bolt, 5/16x 1-1/2 (9) 780279 – Top B Plate (12) 780278 – Hose Clamp, 2 Halves (15) 118773 – Lock washer, 7/8 (2) 118774 – Flat washer, 7/8 – F436 (2) 242691 – Pin Assembly, 2-1/2 x 14-15/16 (2) (mounts with) 117426 – Bolt, 7/8 x 2-3/4 GR8 (1) 118774 – Flat washer, 7/8 – F436 (2) 117416 – Lock Nut, 7/8 Unitorq (l) 242687 – Pin Assembly, 2 x 6-9/16 (2) (mounts 117426 – Bolt, 7/8 x 2-3/4 GR8 (1) with) 118774 – Flat washer, 7/8 – F436 (2) 117416 – Lock Nut, 7/8 Unitorq (l) 573342 – Pin ASSY, 2 x 8-5/16 (4) (mounts 117426 – Bolt, 7/8 x 2-3/4 GR8 (l) with) 118774 – Flat washer, 7/8 – F436 (2) 117416 – Lock Nut, 7/8 Unitorq (l) N. 242794 – Transport Lock – 12-3/4 (2) 117535 – Lock Pin, 5/16 SQ-Wire (2) 242860 – Roller Assembly, Center (1) 118508 – Lock Washer, 5/8 (6) 118605 – Bolt, 5/8x 1 (6) 242691 – Pin Assembly, 2-1/2 x 14-15/16 (2) (mounts with) 118767 – Bolt, 7/8 x 3 GR8 (1) 118774 – Flat washer, 7/8 – F436 (2) 117416 – Lock 7/8 Unitorq (1) 242700 – (2) (comes with) 133136 – Wiper seal, 3 OD (4) 117226 – Bushing, 3 OD x 4 (4) 143375 – LANDROLLER LRX 117173 – Bearing Unit, 4H x 3 (2) IMPORTANT: Setscrew MAX Torque is 30 lb•ft (41 N•m). Do not over-torque. (17-February-2017) 117580 – Bolt, crg 5/8 x 2-1/4 GR8 (8) 242862 – Bushing, 3-5/8 01) x 1 (2) 118447 – Lock Nut, 5/8 (8)
****** Page 26 ****** Center Wheel Components Center Wheels Components 242720 – Center Wheel Strut Assembly (2) (comes with) 133136 – Wiper seal, 3 OD (2) 117226 – Bushing, 3 OD x 4 (2) 573341 – Pin Assembly, 2 x 7-9/16 (2) (mounts with) 118727 – Bolt, 7/8 x 2-1/2 GR8 (1) 118774 – Flat washer, 7/8 – F436 (2) 117416 – Lock Nut, 7/8 Unitorq (1) 131515 – Tire Assembly (4) (comes with) 127018 – Tire, 12.5Lx 15 – 12 PLY (1) 131328 – Rim, 15 x 10 – 6 Bolt (1) 127006 – Valve Stem – TR415 (1) 131709 – Wheel Nut, 9/16 – 18 UNF (24)—• 1 31324 – HubLSpindleAssembly Center and End Wheels 131701 – Hub cap – CTD618 (1) 18835 – Cotter Pin 3/16 x 1-1/2 (1) Cylinder Replacement Bushings (3-133135 – Wiper seal, 2-1/2 OD (4) 117225 – Bushing, 2-1/2 ODx2(4) 123215 – Cylinder, Monarch, 4 x 12 x 2 (2) (Seal Kit: 123049) X. Tire Pressure Center Wheels 12.5Lx 15- 12 PLY: 90 PSI (620 kPa) II 131324- 1 18126 – Bolt, 1/2 x 4 (4) 118420 – Lock Nut, 1/2 (4) Hub & Spindle Assembly (4) 131700 – Hub CTD 618 – c/w Cups (l) 131322 – spindle S618 – c/w Nut (1) 131026 – Dust seal – CR#20140 (1) 131022 – Bearing Cone #25580 (1) 131023 – Bearing cup #25520 (l) 131025 – Bearing cup #LM48510 (1) 131024 – Bearing Cone #48548 (l) 131020 – Flat Washer, I F436 (1) 118423 – Slotted Nut 1-14 UNS (1) Also Requires: 131709 – Wheel Nut 9/16-18 UNF (6) Torque, 9/16 Wheel Nut: 120-130 lb.fr (165-175 N.m) 143375 – LANDROLLER LRX (17-February-2017) -20-
****** Page 27 ****** Wing Frame Components Wing Frame Components 242731 – Wing Frame Assembly (LH) – LRX 51 (1) (other models) 242733 – LRX46 (1) 242735 – LRX41 (1) 242737 – LRX 36 (1) 18144 – Bolt, 5/16x 1-1/2 (1) 1 780279 – Top Plate (l) 780278 – Hose Clamp, 2 Halves (1) QTY: LRX51 (14) LRX 46 (12) LRX41 (10) LRX 36 (8) 242730 – Wing Frame Assembly (RH) – LRX 51 (1) (other models) 242732 – LRX 46 (1) 242734 – LRX 41 (l) 242736 – LRX 36 (l) (0 242691 – Pin Assembly, 2-1/2 x 14-15/16 (2) (mounts with) 118767 – Bolt, 7/8 x 3 GR8 (1) 118774 – Flat washer, 7/8 – F436 (2) 117416 – Lock Nut, 7/8 Unitorq (1) 242880 – Roller Assembly, Wing – LRX 51 (2) (other models) 242875 – LRX 46 (2) 242870 – LRX 41 (2) 242865 – LRX 36 (2) (per roller assembly) 118508 – Lock Washer, 5/8 (6) 118605 – Bolt, 5/8x 1 (6) 143375 – LANDROLLER LRX 242653 – Truss Arm Assy (2) (mounts with) 1 18116 – Bolt, I x 4-1/2 (1) 131020 – Flat washer, 1 – F436 (2) 118911 -Lock Nut, 1 (1) -21- 242862 – Bushing, 3-5/8 ODx 1 (2) 117580 – Bolt, crg 5/8 x 2-1/4 GR8 (8) 117173 – Bearing Unit, 4H x 3 (2) 118447 – Lock 5/8 (8) IMPORTANT: Setscrew MAX Torque is 30 lb•ft (41 N•m). Do not over-tor ue. (17-February-2017)
****** Page 28 ****** End Wheel Frame Components End Wheel Frame Components Cylinder Replacement Bushings (>133135 – Wiper seal, 2-1/2 OD (4) 117225 – Bushing, 2-1/2 OD x 2 (4) 123413 – Cylinder, Monarch 5 x 20 x 2 (2) LRX 51 & 46 (Seal Kit: 123415) – or – 123213 – Cylinder, Monarch LRX41 4-1/2 x 20 x 2 (2) & 36 (Seal Kit: 123214) 573342 – Pin ASSY, 2 x 8-5/16 (12) (mounts with) 117426 – Bolt, 7/8 x 2-3/4 GR8 (1) 118774 – Flat washer, 7/8 – F436 (2) 117416 – Lock Nut, 7/8 Unitorq (1) 242685 – Pin Ass , 2 x 5-9/16 (2) (mounts witK) Bolt, 7/8 x 2-3/4 GR8 (1) 117426 – – Flat washer, 7/8 – F436 (2) 118774 Lock Nutl 7/8 Unitorq (1) 117416 – Tire Pressure End Wheels 12.5Lx 15- 12 PLY: 90 PSI (620 kPa) (17-February-2017) 143375 – LANDROLLER LRX 0.0 0—117535 – Lock Pin, 5/16 so-Wire (2) 242790 – Transport Lock, 20-3/4 (2) Rear Lift Arm Assembly (2) 242845 – (comes with) Wiper seal, 2-1/2 OD (2) 133135 – – Bushing, 2-1/2 OD x 2 (2) 117225 242640 – Assembly (2) (comes with) 133135 – Wiper seal, 2-1/2 OD (4) 117225 – Bushing, 2-1/2 OD x 2 (4) – Rear Lift Link Plate Ass (2) 242850 ‘(comes with) – Wiper seal, 2-1/2 OD (4) 133135 Bushing, 2-1/2 OD x 2 (3) 117225 – 131324 – Hub & Spindle Assembly (4) 118420 – Lock Nut, 1/2 (4) 118126 -Bolt, r131709 – Wheel Nut, 9/16 – 18 UNF (24) 131515 – Tire Assembly (4) (comes with) 127018 – Tire, 12.5Lx 15 – 12 PLY (l) 131328 – Rim, 15 x 10-6 Bolt (1) 127006 – valve stem – TR415 (1) -22-
****** Page 29 ****** Hydraulic Layout – Latch & End Wheels 71 2 3 4 5 6 7 8 Coupler Tip, 3/4 ORB F 141581 – – Connector, 3/4 ORB M x M 141676 – Coupler, Green (+) 141684 Coupler, Green (-) 141685- Adaptor, 1/2 ORB M x ORS M 141703- 141704 – Elbow, 900 1/2 ORB M x ORFSM (4) Tee, 1/2 ORFS MxMxM 141712- 141711 – Elbow, 900 1/2 ORFSX9/16 ORBM (4) Required Hoses for Latch & End Wheel Cylinders 242917 – 242916 – only 1-.@242914 – @ 242913 – @ 242912 – Only 46 Only only 0 242919 – Hose, 3/8 x 398 – 1/2 ORFS F-sw (1) @ 242918 – Hose, 3/8 x 378 – 1/2 ORFS F-SW (1) Hose, 3/8 x 368 Hose, 3/8 x 348 – 242915 – Hose, 3/8 x 338 Hose, 3/8 x 318 – Hose, 3/8 x 308 Hose, 3/8 x 288 – 1/2 ORFS F-SW (1) – 1/2 ORFS F-SW (1) – 1/2 ORFS F-SW (1) 1/2 ORFS F-SW (1) – 1/2 ORFS F-SW (1) – 1/2 ORFS F-SW (1) 141685 Coupler, Green (l) 31 378 398 3/4 ORB F (2i ——141676 – Connector, 3/4 ORB M x M (2) 141684 – Coupler, Green (+) (l) —141703 – Adaptor, 1/2 ORB M x ORFS M (2) Hose Wrap Hoses & Cable – 2 Locations 123076 – Cylinder, Monarch @ 242910 – Hose, 3/8 x 144 – 1/2 ORFS F-sw (l) @ 242909 – Hose, 3/8 x 96 – 1/2 ORFS F-SW (1) @ 242903 – Hose, 3/8 x 44 – 1/2 ORFS F-sw (1) 18 143375 – LANDROLLER LRX (17-February-2017) 123213- LRX41 & 36 123413- LRX51 & 46 2 x4x 1-1/4 (2) (Seal Kit: 123061) Cylinder, Monarch 4-1/2 x 20×2 (2) (Seal Kit: 123214) – or- Cylinder, Monarch 5 x 20 x 2 (2) (Seal Kit: 123415) -23-
****** Page 30 ****** Hydraulic Layout – Power-fold 2 3 4 5 6 7 141581 – 141676 141682- 141683- 141703- 141712- 9 122668 Coupler Tip, 3/4 ORB F – Connector, 3/4 ORB M x M Coupler, Blue (+) Coupler, Blue (-) Adaptor, 1/2 ORB M x ORS M 141704 – Elbow, 900 1/2 ORB M x ORFS M Tee, 1/2 ORFS MxMxM – orifice, 3/4-16 UNF (4) 141581 – Coupler Tip, 3/4 ORB-F (2) 141683 Coupler, Blue (-) (1) 122668 – Orifice, , 3/4-16 UNF (1) i 141676 – Connector, 3/4 ORB M x M (2) 141682 – Coupler, Blue (+) (1) O —141703 – Adaptor, 1/2 ORB M x ORFS M (2) Required Hoses for Power-fold Cylinders @ 242911 – Hose, 3/8 x 240 – 1/2 ORFS F-sw (1) @ 242908 – Hose, 3/8 x 84 – 1/2 ORFS F-sw (1) 36 242902 – Hose, 3/8 x 36 – 1/2 ORFS F-SW (1) 123213 – Cylinder, Monarch 4-1/2 x 20 x 2 (2) (Seal Kit: 123214) 143375 – LANDROLLER LRX (17-February-2017) -24-
****** Page 31 ****** Hydraulic Layout – Center Wheels & Float 2 3 4 5 6 7 10 11 141581 – 141676 141686- 141687- 141703- 141712- Required Hoses for Center Wheel & Float Cylinders @ 242911 – Hose, 3/8 x 240 – 1/2 ORFS F-SW (2) Coupler Tip, 3/4 ORB F – Connector, 3/4 ORB M x M Coupler, Brown (+) Coupler, Brown (-) Adaptor, 1/2 ORB M x ORS M 141704 – Elbow, 900 1/2 ORB M x ORFS M Tee, 1/2 ORFS MxMxM 141705 – Elbow, 900 1/2 ORB Mx ORFS F-SW (1) 141597 – Ball valve – 3/4 ORB F IAAI 10 -25- 141687 Coupler, Brown (l) (5) ‘”—141581 – Coupler Tip, 3/4 ORB F (2) 141676 – Connector, 3/4 ORB M x M (2) 141686 – Coupler, Brown (+) (1)0 —141703 – Adaptor, 1/2 ORB M x ORFS M (2) 11 @ 242907 – Hose, 3/8 x 72 – @ 242906 – Hose, 3/8 x 56 – @ 242905 – Hose, 3/8 x 54 – @ 242904 – Hose, 3/8 x 48 – 44 242903 – Hose, 3/8 x 44 – @ 242901 – Hose, 3/8 x 28 – Hose, 3/8 x 20 – 123215- I /2 ORFS F-SW (1) 1/2 ORFS F-SW (1) I /2 ORFS F-SW (1) 1 /2 ORFS F-sw (1) I /2 ORFS F-SW (2) I /2 ORFS F-SW (1) I /2 ORFS F-SW (1) Cylinder, Monarch 4 x 12×2 (2) (Seal Kit: 123049) 123215 – Cylinder, Monarch 4x12x2(1) (Seal Kit: 123049) 11 5 143375 – LANDROLLER LRX (17-February-2017)
****** Page 32 ****** Electrical Layout / Light Components Ri ht Win Li ht Com onents 129126 – LED Lamp (RH) (1) 118123 – Bolt, 1/4 x I Red 1 18483 – Lock Nut, 1 /4 – Unitorque 242887 – Light Bracket (1) 1 18420 – Lock Nut, 1/2 (2) 118009 – Bolt, 1/2 x 1-1/4 (2) Left_W1ng Light_Components Orange Orange 129125 – LED Lamp (LH) (l) 118123 – Bolt, 1/4xl(6) Red 1 18483 – Lock Nut, I /4 – Unitorque (6) 142135 – SMV Sign (l) 242886 – Light/Sign Bracket (1) Bolt, 1/2 x 1-1/4 (2) 118009 – – Lock Nut, 1/2 (2) 1 18420 1 18735 – screw, 1/4-20 x 3/4 (6) ——129042 – clamp, Rubber Cushion, 3/8 (6) (17-February-2017) 143375 – LANDROLLER LRX Wire Harness – w/plugs (1) LRX 51, Wire Harness 242953 – 242948 – LRX 46, Wire Harness 242943 – LRX 41, Wire Harness LRX 36, Wire Harness 242938 – 129125 – LED Lamp (LH) (1 ) —æc -26- Follow Hose Routing for End Wheel hoses. Attach with Zip Ties 129126 – LED Lamp (RH) (1)
****** Page 33 ****** Warranty 2 Year Limited Warranty – Agricultural Products Degelman Industries Ltd. (“Degelman”) warrants to the original purchaser of any new Degelman equipment, purchased from an authorized Degelman dealer, that the equipment will be free from defects in material and workmanship for a period of two (2) years from the date of delivery, for non-commercial use (including farm, institutional, government, and municipality) and (1 ) year from the date of delivery for commercial use. The obligation of Degelman to the purchaser under this warranty is limited to the repair or replacement of defective parts in the first year and to the provision, but not the installation of replacement parts in the second year. Degelman reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship. This warranty limits its replacement or repair coverage to what is consistent with the warranty of Degelman’s suppliers of purchased components. Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety (90) days from the date of delivery of such part or the expiration of the applicable new equipment warranty period, which ever OCCUrs later. Warranted parts shall be provided at no cost to the user at an authorized Degelman dealer during regular working hours. Warranted replacement parts will either be replaced or rebuilt at Degelman’s discretion. Disclaimer of implied warranties & consequential damages This warranty shall not be interpreted to render Degelman Industries Ltd. liable for injury, death, property damage or damages of any kind, whether direct, consequential, or contingent to property. Without limiting the generality of the foregoing, Degelman shall not be liable for damages resulting from any cause beyond its reasonable control, including, without limitation, loss of crops, any expense or loss of labour, supplies, rental machinery or loss of use. No other warranty of any kind whatsoever, express or implied is made with respect to this sale; and all implied warranties of merchantability and fitness for a particular purpose which exceed the obligations set forth in this written warranty are hereby disclaimed and excluded from this sale. This exclusion shall not apply in any jurisdiction where it is not permitted by law. This limited warranty shall not apply: 2. 3. 4. 5. If, in the sole opinion of Degelman, the unit has been subjected to misapplication, abuse, misuse, negligence accident or incorrect off-site machine set-up. To any goods that have sustained damage or deterioration attributable to a lack of routine maintenance (eg. Check and Re-torque of fastening hardware, Hydraulic fluid purities, drive train alignments, and clutch operation) If parts not made or supplied by Degelman have been used in the connection with the unit, if, in the sole judgement of Degelman such use affects its performance, safety, stability or reliability. If the unit has been altered or repaired outside of an authorized Degelman dealership in a manner which, in the sole judgement of Degelman, affects its performance, safety, stability or reliability. To expendable or wear items such as (eg. Harrow tines, Rock Picker and Rock Rake wear teeth and replaceable bushings and pins.) and any other items that in the company’s sole judgement are a wear item. No employee or representative of Degelman Industries Ltd. is authorized to change this limited warranty in any way or grant any other warranty unless such change is made in writing and signed by the Degelman Service Manager. This limited warranty is subiect to any future availability of supply, which may directly affect Degelman’s ability to obtain materials or manufacture replacement parts. Degelman reserves the right to make improvements in design or changes in specifications at any time, without incurring obligations to owners of equipment previously delivered This limited warranty is subject to compliance by the customer to the enclosed Retail Customer’s Responsibility Under Degelman Warranty. 143375 – LANDROLLER LRX (17-February-2017)
****** Page 34 ****** Warranty Retail Customer’s Responsibility Under Degelman Warranty. It is the retail customer and/or Operator’s responsibility to read the Operator’s Manual, to operate, lubricate, maintain and store the equipment in accordance with all instructions and safety procedures. Failure of the operator to read the operators manual is a misuse of this equipment. It is the retail customer and/or operators responsibility to inspect the product and to have any part(s) repaired or replaced when continued operation would cause damage or excessive wear to other parts or cause safety hazard. It is the retail customer’s responsibility to deliver the product to the authorized Degelman dealer, from whom he purchased it, for service or replacement of defective parts, which are covered by warranty. Repairs to be submitted for warranty consideration must be made within forty-five days of failure. It is the Retail Customer’s responsibility for any cost incurred by the dealer for hauling of the product for the purpose of performing a warranty obligation or inspection. WARRANTY INFORMATION Make certain the warranty registration card has been forwarded to: Degelman Industries Ltd. Box 830 -272 Industrial Dr. Regina, SKI Canada S4P 3B1 Always give your dealer the serial number of your Degelman product when ordering parts or requesting service or other information. The serial number is located on the machine as shown in the diagram below. In the space provided record the model number, the serial number and the date of purchase to assist your dealer in providing you with prompt and efficient service. SERIAL NUMBER: MODEL NUMBER: DATE OF PURCHASE: 143375 – LANDROLLER LRX (17-February-2017) DEGELMAN INDUSTRIES LTD. REGINA, SASR., CANADA 8eRiAL No. Serial Number Plate Location LANøøoLLEø LB*51 -28-
FREE ENGLISH PDF
OPERATING INSTRUCTIONS
USER GUIDE – USER MANUAL
OWNER GUIDE – OWNER MANUAL
REFERENCE GUIDE – REFERENCE MANUAL
INSTRUCTION GUIDE – INSTRUCTION MANUAL