Free English DATALOGIC SM1 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD DATALOGIC SM1 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What do the different states of the Yellow LED on the DATALOGIC SM1 indicate?
The Yellow LED on the DATALOGIC SM1 indicates the “LIGHT sensed” status:
• LED ON steadily means the output is ON, with the sensor working in LIGHT mode.
• LED flashing means there is a marginal excess gain of 1…1.5.
What do the different states of the Green LED on the DATALOGIC SM1 indicate?
The Green LED on the DATALOGIC SM1 provides status information about power and the output:
• LED ON steadily means that power to the sensor is ON.
• LED flashing means there is an output overload.
How do I install the DATALOGIC SM1 sensor?
The DATALOGIC SM1 sensor can be positioned by using the two holes in the housing. Use two screws (M2x16 or longer) with nuts and washers for mounting.
How should I wire the NPN output on the DATALOGIC SM1?
For the NPN output configuration on the DATALOGIC SM1, connect the wires as follows:
• BLUE: Connect to the 10…30 Vdc negative terminal.
• BROWN: Connect to the 10…30 Vdc positive (+) terminal.
• BLACK: Connect to the Load.
How should I wire the PNP output on the DATALOGIC SM1?
For the PNP output configuration on the DATALOGIC SM1, connect the wires as follows:
• BROWN: Connect to the 10…30 Vdc positive (+) terminal.
• BLUE: Connect to the 10…30 Vdc negative terminal.
• BLACK: Connect to the Load.
What are the technical specifications for the DATALOGIC SM1?
| Power supply: | 10…30 Vdc limit values |
| Current consumption: | 25 mA max. (output current excluded) |
| Output: | PNP or NPN (short circuit protection) |
| Operating mode: | LIGHT |
| Output current: | 50 mA max. |
| Output saturation voltage: | < 0.25 V at 10 mA; < 0.5 V at 50 mA |
| Response time: | 1 ms |
| Switching frequency: | 500 Hz |
| Operating temperature: | -20 … 55 °C |
| Storage temperature: | -25 … 70 °C |
| Electrical shock protection: | Class 2 |
| Operating distance (typical values): | 3…20 mm (on White 90%) |
| Emission type: | Red (630 nm) |
| Vibration: | 0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6) |
| Shock resistance: | 11 ms (30 G) 6 shock for every axis (EN60068-2-27) |
| Housing material: | ABS |
| Lenses material: | PMMA |
| Mechanical protection: | IP67 |
| Connections: | 2 m cable Ø 2.3 mm 3 wires |
| Weight: | 16 g |
What are the dimensions of the DATALOGIC SM1?
The physical dimensions of the DATALOGIC SM1 are as follows:
• Height: 25.7 mm
• Width: 8.3 mm
• Depth: 11.6 mm
• Distance between mounting holes: 15 mm
• Mounting hole size: 4.1 mm
• Distance from lens center to mounting hole: 9.2 mm
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD DATALOGIC SM1 (01) PDF DOCUMENT