DASH BREW2GO DCBM10S (01) PDF DOCUMENT

When using electrical appliances, basic safety precautions should always be followed, including:

• Read all instructions.

• Remove all bags and packaging from appliance before use.

• Never leave appliance unattended when in use.

• Make sure the appliance is cleaned thoroughly before using.

• Do not use appliance for other than intended use. For household use only. Do not use outdoors.

• Do not operate this appliance with a damaged cord, damaged plug, after the appliance malfunctions, is dropped, or damaged in any manner.

• For maintenance other than cleaning, please contact StoreBound.

• Never use abrasive cleaning agents to clean your Dash Brew2Go™ Portable Cold Brew System.

• To prevent the risk of fire, electric shock, or personal injury, do not put cord, plug, or appliance in or near water or other liquids.

• Do not place appliance on or near a hot gas burner, hot electric burner, or in a heated oven.

• Refrain from using attachments that are not recommended by the appliance manufacturer, as this may result in fire, electric shock, or personal injury.

• Do not let the cord touch hot surfaces or hang over the edge of tables or counters.

• This appliance can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

• The appliance is not a toy. Do not let children use this appliance. Close supervision is necessary when any kitchen appliance is used by or near children.

• Always be sure to unplug the appliance from outlet prior to moving, cleaning, storage, and when not in use.

• StoreBound shall not accept liability for damages caused by improper use of the appliance.

• This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug will fit in a polarized outlet only one way. If the plug does not completely fit in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way.

• A short power supply cord is provided to reduce the risk resulting from becoming entangled in or tripping over a longer cord. An extension cord may be used if care is exercised in its use. If an extension cord is used, the marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance. The extension cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over unintentionally.

The Brew2Go Portable Cold Brew System includes the following parts:

Motor: The power unit for the brewing process.

• Power Button / Indicator Light: The brew cycle begins once pressed. The light indicates status.

• Power Port: Attach the USB Cord here to charge the unit.

Motor Cover: Covers the motor during operation.

Coffee Filter Cylinder: Holds the coffee grounds during brewing.

Cylinder Extender: Attaches to the Coffee Filter Cylinder.

Portable Cup: Holds the water and finished cold brew. It has a Max Line indicating the maximum water level for 1.5 cups of cold brew.

Travel Lid: A lid for the Portable Cup for on-the-go use.

Silicone Straw: A reusable straw for drinking.

Cleaning Brush: Used for cleaning the cylinders.

Precision Scoop: For measuring coffee grounds.

USB Cord: For charging the motor unit.

Before first use, remove all packaging material. Then thoroughly clean the Brew2Go™ Portable Cold Brew System and wipe down all parts with a moist cloth. Prior to brewing, ensure the unit is fully charged. Use the included USB Cord to charge, taking note that once the light stops blinking, the unit is fully charged.

1. Remove everything from the Portable Cup. For 1.5 cups of cold brew, fill the Cup with room temperature water to the MAX line. Do not exceed the line and do not use hot water.

2. Disassemble the Cylinders. Use the Precision Scoop to add three scoops of coffee grounds to the Coffee Filter Cylinder or fill it to the top.

3. Attach the two Cylinders together. Then twist to attach the Cylinder Extender to the Motor Unit. Set aside.

4. Twist to attach the Motor Cover to the Portable Cup. Then insert the other assembled pieces into the top of the Motor Cover.

1. Once assembled and set up, begin brewing by pressing the Power Button on the Motor. The Indicator Light will turn on and the brewing process will begin.

2. When brewing is complete, the Indicator Light will turn off. A typical brewing cycle will last about 10-15 minutes. However, depending on preference and recipe, the cold brew may be at the desired intensity before the brewing cycle completes. To stop brewing and end the cycle early, simply press the Power Button.

3. When finished brewing, remove all parts from the Cup and disassemble them. Install the Travel Lid on the Portable Cup and turn clockwise to secure.

When the unit is low on battery, the light will begin blinking. For best results, do not brew while the unit is low on battery. Charge the unit.

If residual water remains in the Coffee Filter Cylinder after brewing is complete, press and hold the Power button to drain the water.

Yes, you can use the Brew2Go to make fresh tea. Follow the instructions for making cold brew, but replace the ground coffee with your preferred loose-leaf tea.

The Brew2Go™ Portable Cold Brew System is NOT dishwasher safe. Clean all parts by hand with soap and water. Use the included Cleaning Brush to properly clean the Cylinders. Make sure all parts are dry before storing.

Easily attach the magnetized USB Cord to the Motor to charge the product. When charging is complete, the Indicator Light will turn off. When the battery is low, the Indicator Light will flash to signal the need for a recharge.

Before use, make sure the unit is fully charged and has a minimum of one cup of water for optimal brewing results.

Ensure that both Cylinders are properly cleaned.

The unit is low on battery. Use the USB Cord to fully charge the unit.

Check to make sure the Coffee Filter Cylinder isn’t damaged. If there is damage, please consult Customer Service to receive replacement parts.

Ensure that both Cylinders are properly cleaned.

Prep Time: 5-15 minutes • Serves: 1

Ingredients:

• 1 cup water

• 2-3 tablespoons oat milk

• 3 Precision Scoops of preferred coffee grounds

• Ice

• 1-2 tablespoons sweetener of choice

Directions:

1. Fill the Brewing Cup with 1 cup of water and 2-3 tablespoons of oat milk.

2. Scoop coffee grounds into the Filter Cylinder of the Brew2Go Cold Brew Maker. Finish assembling the Brewing Apparatus as per instructions.

3. Once assembled, press the Brewing Button to begin brewing. Brew for 3-5 minutes, taking note that the Brewing Cycle will continue until the Brewing Button is pressed to stop it. For a stronger brew, feel free to brew for the entire Brewing Cycle, about 12-15 minutes.

4. When brewing is complete, remove the Motor and the Brewing Apparatus and set aside for cleaning.

5. In the Brewing Cup, add sweetener and more oat milk if desired. Stir to combine then add ice.

6. Serve, sip, savor, and sew your oats!

Prep Time: 5-15 minutes • Serves: 1

Ingredients:

• 1 cup water

• 2-3 tablespoons coconut milk

• 3 Precision Scoops of preferred coffee grounds

• 1-2 tablespoons caramel syrup

• Ice

• Toasted coconut flakes (optional)

Directions:

1. Fill the Brewing Cup with 1 cup of water and 2-3 tablespoons of oat milk.

2. Scoop coffee grounds into the Filter Cylinder of the Brew2Go Cold Brew Maker. Finish assembling the Brewing Apparatus as per instructions.

3. Once assembled, press the Brewing Button to begin brewing. Brew for 3-5 minutes, taking note that the Brewing Cycle will continue until the Brewing Button is pressed to stop it. For a stronger brew, feel free to brew for the entire Brewing Cycle, about 12-15 minutes.

4. When brewing is complete, remove the Motor and the Brewing Apparatus and set aside for cleaning.

5. In the Brewing Cup, add caramel syrup and more coconut milk if desired. Stir to combine then add ice. Top with toasted coconut flakes if desired.

6. Serve and go nuts!

Prep Time: 5-15 minutes • Serves: 1

Ingredients:

• 1 cup water

• 2-3 tablespoons milk of choice

• 3 Precision Scoops of preferred coffee grounds

• 1 tablespoon pumpkin puree

• ½ teaspoon vanilla

• Pinch of pumpkin pie spice

• 1-2 tablespoons sweetener of choice

• Ice

Directions:

1. Fill the Brewing Cup with 1 cup of water and 2-3 tablespoons of oat milk.

2. Scoop coffee grounds into the Filter Cylinder of the Brew2Go Cold Brew Maker. Finish assembling the Brewing Apparatus as per instructions.

3. Once assembled, press the Brewing Button to begin brewing. Brew for 3-5 minutes, taking note that the Brewing Cycle will continue until the Brewing Button is pressed to stop it. For a stronger brew, feel free to brew for the entire Brewing Cycle, about 12-15 minutes.

4. When brewing is complete, remove the Motor and the Brewing Apparatus and set aside for cleaning.

5. In the Brewing Cup, add pumpkin puree, vanilla, pumpkin pie spice, sweetener, and more milk if desired. Stir to combine then add ice.

6. Serve and enjoy this cozy fall fave!

Prep Time: 5-15 minutes • Serves: 1

Ingredients:

• 1 cup water

• 2-3 tablespoons milk of choice

• 3 Precision Scoops of preferred coffee grounds

• 1-2 tablespoons maple syrup

• 2 teaspoons cocoa powder

• Pinch cayenne pepper

• Pinch cinnamon

• Ice

Directions:

1. Fill the Brewing Cup with 1 cup of water and 2-3 tablespoons of oat milk.

2. Scoop coffee grounds into the Filter Cylinder of the Brew2Go Cold Brew Maker. Finish assembling the Brewing Apparatus as per instructions.

3. Once assembled, press the Brewing Button to begin brewing. Brew for 3-5 minutes, taking note that the Brewing Cycle will continue until the Brewing Button is pressed to stop it. For a stronger brew, feel free to brew for the entire Brewing Cycle, about 12-15 minutes.

4. When brewing is complete, remove the Motor and the Brewing Apparatus and set aside for cleaning.

5. In the Brewing Cup, add maple syrup, cocoa powder, spices, and more milk if desired. Stir to combine then add ice.

6. Serve and go loco for cocoa!

Prep Time: 5-15 minutes • Serves: 1

Ingredients:

• 2-3 tablespoons non-dairy milk

• 1 cup water

• 3 Precision Scoops of preferred coffee grounds

• 1 tablespoon chocolate syrup

• ½ teaspoon cinnamon

• ¼ teaspoon cloves

• Ice

• Non-dairy whipped cream (optional)

Directions:

1. Fill the Brewing Cup with 1 cup of water and 2-3 tablespoons of oat milk.

2. Scoop coffee grounds into the Filter Cylinder of the Brew2Go Cold Brew Maker. Finish assembling the Brewing Apparatus as per instructions.

3. Once assembled, press the Brewing Button to begin brewing. Brew for 3-5 minutes, taking note that the Brewing Cycle will continue until the Brewing Button is pressed to stop it. For a stronger brew, feel free to brew for the entire Brewing Cycle, about 12-15 minutes.

4. When brewing is complete, remove the Motor and the Brewing Apparatus and set aside for cleaning.

5. In the Brewing Cup, add chocolate syrup, spices, and more non-dairy milk if desired. Stir to combine then add ice.

6. Top with whipped cream to serve and savor this sweet treat!