CYBERPOWER HT705GR (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD CYBERPOWER HT705GR (01) PDF MANUAL


PDF Content Summary: 7-Outlet Surge Protector HT705GR CONGRATULATIONS ON YOUR PURCHASE Thank you for selecting the CyberPower HT705GR Surge Protector. The information contained in this brochure explains the features and operation of the HT705GR. Please take a few moments to read this manual. QUICK START GUIDE 1. Connections - Connect infra-red (IR) controller to main surge protector via small input jack. Then connect all power-saving controlled and non-controlled equipment to surge protector and assure all equipment is powered o or on standby mode. Plug surge protector into wall outlet and turn on using green rocker switch. LED indicators (protected & grounded) will illuminate. 2. Power-Saving Detection - The HT705GR will detect the connected equipment and Energy Saving LED will illuminate. To reset the power-saving outlets, press and hold the IR Sensor button for more than 10 seconds, release and this will trigger re-detection of the connected equipment. 3. The Energy Saving Timer - When the IR Sensor receives IR signals within the energy saving time window, the Energy Saving outlets will power on. When the IR Sensor no longer receives signals, the Energy Saving outlets will power o after a specific time period. The energy saving timer default setting is 1 hour. If you want to change the energy saving time window, you need to press the IR Sensor button for more than 3 seconds (LED will • UL Clamping Voltage: UL 1449 3rd/500V (H-N, H-G, N-G) • Maximum Peak Current: 60,000A • 3 AC Lines Protected: H-N: 30,000A, H-G: 15,000A, N-G: 15,000A; (The maximum surge possible on household Wiring is 6,000 volts) • Response Time: Less than 1 nanosecond • Attenuation: Up to 43dB • EMI/RFI Filtration: 150 kHz to 100 MHz • IR Detection Range / Degree: 17 ft/ 70 degrees CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK - Use only in dry locations and only indoors. DO NOT plug into another relocatable power tap. DO NOT “daisy chain” surge protectors. DO NOT use with any aquarium equipment. DO NOT use if properly grounded outlets are not available. DO NOT install this device if there is not at least 10 meters (30 feet) or more of wire between the electrical outlet and electrical service panel. This device features an internal protection that will disconnect the surge protective component at the end of its useful life, but will maintain power to the load – now unprotected. TROUBLESHOOTING

flash 3 times), release, and surge protector will default into the settings mode. Follow the setting table below: To set energy saving Problem The Always On outlets are To Check • Ensure plug connections are secure and

time to power o Press the button on the IR Sensor To confirm the setting, the LED on the IR Sensor will flash: not receiving the power power switch is set to on/reset position.

3 1 2 1 hour (Default settting) 2 hours Once (one second) then release 2 times or more (one second each) then release 1 time 2 times The HT705GR does not power o the connected • Ensure the equipment is plugged into the Energy Saving outlets, not into the Always On outlets. • The HT705GR has not detected the connected equipment in standby. Please

8 4 5 8 7 4. Timer Shut-Down - When the timer expires, the IR Sensor will continue to flash for 15 minutes, then the Energy Saving outlets will power o . If you want to reset timer, press the IR Sensor button or use your standard device remote controller. FEATURES 1. Surge Protected Indicator LED Illuminated when the surge protection feature is working properly. 2. Ground Indicator LED Illuminated when the ground protection feature is working properly. 3. Energy Saving Indicator LED Illuminated when the Energy Saving outlet is powered on. Not illuminated when the Energy Saving outlet is powered o . 4. Always On Outlets The outlet power is always on. 5. Energy Saving Outlets When the energy saving timer expires, the IR Sensor will continue to flash for 15 minutes, then the Energy Saving outlets will power o . If you want to turn on the Energy Saving outlets, you can press the IR Sensor button or use your device remote controller. 6. IR Sensor The Sensor for receiving the IR signals. 7. IR Sensor Button Use the button to turn on the Energy Saving outlets or to place surge 6 protector into the setting mode. 8. 2 Wide Spaced Outlets For transformer-sized plugs. SPECIFICATIONS equipment in standby mode. The IR Sensor is not operating. The IR Sensor flashes frequently during normal operation. The surge protected LED of the HT705GR is on, but my IR Sensor LED does not work (when the IR Sensor is plugged in and powered on). The HT705GR is not working / the protected LED is not illuminated. press the IR Sensor button for more than 3 seconds (LED will flash 3 times) and release to enter into the setting mode. When switching surge o /on again assure all connected equipment are placed in power-o or standby mode. • Turn o the HT705GR power, re-plug the IR Sensor cable, then turn on the HT705GR. • It may be radio frequency interference. Check for other devices that may be causing interference in the area. • Move the IR Sensor to another location that is within line of sight and normal operation range of connected equipment remote controls. • Ensure the IR Sensor cable is safely and securely connected to the HT705GR, and; • Press the IR Sensor button, the Energy Saving outlets will turn on. • Remove all the connected equipment and power cord from the wall outlet. Reset surge protector by pressing and hold the IR Sensor button for more than 10 seconds, then release. • The default setting for the energy saving USER’S MANUAL • Model Number: HT705GR • Outlets: 2 Always On outlets & 5 Energy Saving outlets (5 Standard Outlets and 2 transformer spaced outlets ) • Surge Protection: 1500 Joules • Electrical Rating: 125V/15A/1875W 1 The connected equipment turned o after 1 hour. time is 1 hour. • If you want to change the energy saving time, please check the quick start guide section to change default energy saving time from 1 or 2 hours. 2

Copyright © 2017 Cyber Power Systems, Inc. All rights reserved.

TECHNICAL SUPPORT Please contact our Tech Support department with installation, troubleshooting, or general product questions. • Phone: 1-877-297-6937 • Email: tech@cpsww.com • Hours of Operation: Monday – Friday 7:00am – 6:00pm CST LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARANTEE Read the following terms and conditions carefully before using the CyberPower HT705GR (the “CPS Product”). By using the CPS Product, you consent to be bound by the terms and conditions of this Limited Warranty and Connected Equipment Guarantee (together referred to as this “Warranty”). IF YOU DO NOT AGREE TO THE TERMS AND CONDITIONS OF THIS WARRANTY, YOU SHOULD RETURN THE PRODUCT FOR A FULL REFUND PRIOR TO USING IT. Who is providing this Warranty, what does it cover? Cyber Power Systems (USA), Inc. (“CyberPower”) provides this Limited Warranty. It only covers the original purchaser and ends if you no longer own the CPS Product. This warranty covers defects in materials and workmanship in the CPS Product under normal use and conditions. It also covers equipment connected to the CPS Product and damaged because of the failure of the CPS Product. This warranty covers the CPS Product and connected equipment for as long as you own the CPS Product. How Do You Open A Connected Equipment Claim? 1. Call us at (877) 297-6937 or write to us at Cyber Power Systems (USA), Inc., 4241 12th Ave. E., STE 400, Shakopee, MN 55379, or send us an e-mail message at claims@cpsww.com for instructions, within 10 days of the occurrence. 2. When you contact CyberPower, identify the Product, the Purchase Date, and the item(s) of Connected Equipment. Have information on all applicable insurance or other resources of recovery/payment that are available to the Initial Customer and Request a Claim Number. 3. You must provide a dated purchase receipt (or other proof of the original purchase) for the CyberPower unit and connected equipment. You also need to provide a description of the damage to your connected equipment. 4. Pack and ship the product to CyberPower and, if requested, the item(s) of Connected Equipment, a repair cost estimate for the damage to the Connected Equipment, and all claim forms that CyberPower provides to you. Show the Claim Number on the shipping label or include it with the product. You must prepay all shipping costs, you are responsible for packaging and shipment, and you must pay the cost of the repair estimate. What will CyberPower do to correct problems? CyberPower will inspect and examine the CPS Product. If the CPS Product is defective in material or workmanship, CyberPower will repair or replace it at CyberPower’s expense, or CyberPower will refund the full purchase price you paid for the CPS Product (purchase receipt showing price paid is required). If the CPS Product failed to protect any equipment plugged into it, we will also send you forms for making your claim for the connected equipment. We will repair or replace the equipment that was damaged because of the failure of the CPS Product or pay you the fair market value (NOT REPLACEMENT COST) of the equipment at of the time of the damage. We will use Orion Blue Book, another a third-party valuation guide, eBay, craigslist, or other source to establish that amount. Our maximum liability is limited to $75,000 for the HT705GR. Who pays for shipping? We pay when we send items to you; you pay when you send items to us. What are some things this Warranty does not cover? 1. THIS WARRANTY DOES NOT COVER ANY SOFTWARE THAT WAS DAMAGED OR NEEDS TO BE REPLACED DUE TO THE FAILURE OF THE CPS PRODUCT OR ANY DATA THAT IS LOST AS A RESULT OF THE FAILURE OR THE RESTORATION OF DATA OR RECORDS, OR THE REINSTALLATION OF SOFTWARE. 2. This Warranty does not cover: misuse, modification, operation or storage outside environmental limits of the CPS Product or the equipment connected to it, or for damage while in transit or in storage, nor if there has been improper operation or maintenance, or use with items not designed or intended for use with the CPS Product, such as laser printers, appliances, aquariums, medical or life support devices, etc. What are the other limitations? The sole and exclusive remedies of the Initial Customer are those provided by this Warranty. 1. This Warranty does not apply unless the CPS Product and the connected equipment were connected to properly wired and grounded outlets (including compliance with electrical and safety codes of the most current electrical code), without the use of any adapters or other connectors. 2. The CPS Product must have been plugged directly into the power source and the equipment connected to the CPS Product must be directly connected in the CPS Product, not “daisy-chained” together in serial fashion with any extension cords, another Product or device similar to the CPS Product, surge suppressor, or power tap. Any such installation voids the Warranty. 3. The CPS Product and connected equipment must have been used properly in a suitable and proper environment, in conformance with any applicable license, instruction manual, or warnings. 4. The CPS Product must have been used at all times within the limitations on the CPS Product’s VA capacity. Where can I get more information? Contact CyberPower at 4241 12th Ave E., STE 400, Shakopee, MN 55379; call us at (877) 297-6937; or send us an e-mail message at claims@cpsww.com. PRODUCT REGISTRATION Prompt product registration assures coverage under the Limited Warranty, and also allows the opportunity to be notified of product enhancements, upgrades, and other announcements. Registration is quick and easy. Go to Product Registration page at cyberpower.com. CONTACT INFORMATION Cyber Power Systems, Inc. 4241 12th Avenue East Suite 400 Shakopee, MN 55379 Toll-free: 1-877-297-6937 | CyberPower.com FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit di erent from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. ICES-003: This Class B digital apparatus complies with Canadian ICES-003. Please join CyberPower in caring for the environment by recycling this manual. This device is manufactured using environmentally-safe procedures in compliance with the Restriction of Hazardous Substances (RoHS) directive. © 2017 Cyber Power Systems, Inc. cyberpower.com

3 4


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply