CUSTOM SR300NM (01) PDF MANUAL

Your attention is drawn to the following actions that could compromise the characteristics of the product:

• Read and retain the instructions which follow.

• Follow all indications and instructions given on the device.

• Make sure that the surface which the device rests is stable. If it is not, the device could fall, seriously damaging it.

• Do not fix indissolubly the device or its accessories such as power supplies unless specifically provided in this manual.

• When positioning the device, make sure cables do not get damaged.

• Before any type of work is done on the machine, disconnect the power supply.

• Take care the operating temperature range of equipment and its ancillary components.

• Do not block the ventilation openings.

• Do not insert objects inside the device as this could cause short-circuiting or damage components that could jeopardize printer functioning.

• Do not carry out repairs on the device yourself, except for the normal maintenance operations given in the user manual.

• The equipment must be accessible on these components only to trained, authorized personnel.

• Periodically perform scheduled maintenance on the device to avoid dirt build-up that could compromise the correct, safe operation of the unit.

• Do not look directly into LED beam or reflected led beam from a mirrored surface, it may cause pain.

• Unplug or turn off the device be sure to stop the led beam before cleaning the portion of the device where LED light is generated and received (emitter/receiver). Otherwise, exposure may cause pain.

The crossed-out rubbish bin logo means that used electrical and electronic products shall NOT be mixed with unsorted municipal waste. For more detailed information about recycling of this product, refer to the instructions of your country for the disposal of these products.

Do not dispose of this equipment as miscellaneous solid municipal waste, but arrange to have it collected separately.

The re-use or correct recycling of the electronic and electrical equipment (EEE) is important in order to protect the environment and the wellbeing of humans.

In accordance with European Directive WEEE 2002/96/EC, special collection points are available to which to deliver waste electrical and electronic equipment and the equipment can also be handed over to a distributor at the moment of purchasing a new equivalent type.

The public administration and producers of electrical and electronic equipment are involved in facilitating the processes of the re-use and recovery of waste electrical and electronic equipment through the organisation of collection activities and the use of appropriate planning arrangements.

Unauthorised disposal of waste electrical and electronic equipment is punishable by law with the appropriate penalties.

1. Disconnect the cradle from your computer.

2. Scan the “Bluetooth SPP mode” barcode.

3. Scan the “Cradle pairing mode” barcode.

4. Connect the cradle to your computer.

5. Scan the “Pairing mode” barcode.

After successfully pairing, the scanner will beep and the LED will turn blue and stop flashing.

To pair the scanner with an iOS or Android mobile device, use the barcodes below. If you have previously paired this scanner with this device, navigate to the Bluetooth setting and ‘forget’ for the scanner; before attempting to pair again.

1. Scan the “Clear previous pair” barcode.

2. Scan the “HID mode” barcode.

3. Scan the “Pairing mode” barcode.

4. Open the Bluetooth setting on your device and connect to the “Bluetooth Scanner”.

After successfully pairing, the scanner will beep and the LED will turn blue and stop flashing. When paired with an iOS device, quickly double press the trigger to toggle the on-screen keyboard.

To toggle between barcode scanning and on-screen keyboard input to work with iOS devices, scan the “iOS keyboard On/Off” barcode.

After you enable the iOS hot key by scanning the “Enable iOS Hot Key” barcode, you may simply press the trigger once to toggle the iOS device’s on-screen keyboard.

The sleep setting barcodes configure how long the scanner can be idle before powering off. Scan the barcode corresponding to your desired time:

• 2 minutes

• *5 minutes (default)

• 10 minutes

• 20 minutes

• Never

• Power Off

While in memory mode, the scanner will store all barcodes scanned until the “Transmit Stored Data” barcode is scanned.

• To enter memory mode, scan the “Enter Memory Mode” barcode.

• To transmit all the stored data, scan the “Transmit Stored Data” barcode.

• To find out how many barcodes are stored, scan the “Transmit Count of Stored Barcodes” barcode.

• To delete all stored data, scan the “Clear All Stored Data” barcode.

• To exit memory mode, scan the “Exit Memory Mode” barcode.

Scan the barcode that corresponds to the desired auto reconnect duration:

• 1 minute

• 5 minutes

• 10 minutes

• *20 minutes (default)

To change the vibration setting, scan the appropriate barcode:

• To turn on vibration, scan the “Enable” barcode.

• To turn off vibration, scan the “*Disable” barcode (default).

To make a command barcode and scan it:

Use the format: %%BT_NAME=ADCB

“ADCB” is the part to be replaced with your customized name.