Free English CRUX SWRSB-58 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD CRUX SWRSB-58 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the product features of the CRUX SWRSB-58?
The CRUX SWRSB-58 features include:
– Retains factory features in select Saab vehicles while functioning with an aftermarket radio.
– Retains Steering Wheel Controls via built-in, pre-programmed interface.
– With navigation outputs (Reverse gear, Illumination and Speed signal).
– Provides Accessory Power (2A MAX).
Which Saab vehicles and systems are compatible with the CRUX SWRSB-58?
The CRUX SWRSB-58 is compatible with vehicles with non-amplified and standard amplified systems. The specific vehicle applications are:
– Saab 9-3 (2004 – 2005)
– Saab 9-5 (2000 – 2005)
How do I select the correct harness for installation with the CRUX SWRSB-58?
The CRUX SWRSB-58 includes 2 harnesses (SWRSB-58 Harness and SWRSB-58 Harness B). Use the harness that matches the factory connectors on your vehicle. Refer to the installation diagrams provided with the unit for each harness.
What is the wiring color code guide for the CRUX SWRSB-58?
The wiring connections for the CRUX SWRSB-58 are as follows:
Illumination (+): Orange
Reverse Gear: Red/White
Vehicle Speed Sense: Purple/White
+12V Constant: Yellow
+12V ACC: Red
Ground: Black
Amp Turn on: Blue/White
Dimmer: Orange/White
Power Antenna: Blue
Right Front (+): Gray
Right Front (-): Gray/Black
Left Front (+): White
Left Front (-): White/Black
Right Rear (+): Violet
Right Rear (-): Violet/Black
Left Rear (+): Green
Left Rear (-): Green/Black
How do I set the DIP switches for my aftermarket radio on the CRUX SWRSB-58?
Set the DIP switches on the SWC Module based on your radio brand using the table below:
| RADIO BRAND | DIP# 1 | DIP# 2 | DIP# 3 |
|---|---|---|---|
| Atoto, Dual, Fahrenheit, Jensen | OFF | ON | ON |
| Pioneer, Power Acoustik, Soundstream | OFF | ON | ON |
| Blaupunkt, Most off-brand Radio | OFF | ON | ON |
| Alpine | OFF | OFF | OFF |
| Clarion | ON | ON | OFF |
| Kenwood | ON | ON | ON |
| JVC | ON | OFF | ON |
| Boss, Old Sony | ON | OFF | OFF |
| New Sony | OFF | ON | OFF |
Note: For Atoto, Blaupunkt, Dual, Farenheit, Power Acoustik, Soundstream, and most off-brand radios, check the aftermarket radio’s manual to see if the SWC buttons need to be programmed.
Which 4-Pin SWC cable option should I use with the CRUX SWRSB-58?
Use the proper 3.5MM to 4-Pin cable for the aftermarket radio you are using and plug it into the aftermarket radio’s SWC port or connect the Blue/Yellow wire to Kenwood and JVC radios.
Option A: Used for ALPINE, CLARION, JVC, and KENWOOD units (Blue/Yellow wire is attached).
Option B: Used for ATOTO, BLAUPUNKT, BOSS, DUAL, FARENHEIT, JENSEN, POWER ACOUSTIK, PIONEER, SONY, SOUNDSTREAM and Most Off-Brand Radios.
Note: Cap or insulate the 3.5mm plug or Blue/Yellow wire if not being used.
How do I connect the CRUX SWRSB-58 to a radio that uses wires instead of a 3.5mm jack for SWC?
For aftermarket radios that have wires for SWC connections, cut off the 3.5mm plug on the Crux SWC Cable (option B) and connect the SWC wires as follows:
– RED to SWC Key 1
– WHITE to SWC Key 2
– SHIELD to SWC Ground
Note that there are some radios that only have SWC1 and SWC2; in this case, “shield” does not need to be connected.
CLICK HERE TO DOWNLOAD CRUX SWRSB-58 (01) PDF DOCUMENT