COOPER CROUSE-HINDS TMC-K2 (01) PDF MANUAL


Post questions, comments, reviews or errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD COOPER CROUSE-HINDS TMC-K2 (01) PDF MANUAL


PDF Content Summary: CROUSE-HINDS TMC-K SERIES CORROSION PROTECTION KIT Installation & Maintenance Information IF 1378 SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE APPLICATIONS TMC-K Kit Catalog No. TMC Fitting Catalog No. TMCX Fitting Catalog No. TMC-K Series Cold ShrinkTM Corrosion Protection Kits are designed to provide a quick and easy method for protecting TMC and TMCX Series Terminator® Cable Fittings from the corrosive influences of wet and salt-fog installation environments. A TMC-K Cold Shrink Corrosion Protection Assembly is an open-ended tubular rubber sleeve which is factory expanded and assembled onto a removable core. The core is removed after the assembly has been positioned for installation over a Terminator® Cable Fitting. TMC-K1 TMC-K2 TMC-K3 TMC-K4 TMC-K5 TMC-K6 TMC-K7 TMC-K8 TMC-K9 TMC-K10 TMC165 TMC285 TMC3112 TMC4140 TMC5161 TMC6206 TMC7247 TMC8302 TMC9352 TMC10402 TMCX165 TMCX285 TMCX3112 TMCX4140 TMCX5161 TMCX6206 TMCX7247 TMCX8302 TMCX9352 TMCX10402 TMC-K Cold ShrinkTM Assemblies are made from EPDM rubber material that contains no chlorides or sulfurs. They conform to the moisture seal requirements of ANSI Standard C119.1. TMC-K Series Corrosion Protection Kits are assigned according to the following table: METHODS: TMC-K1, TMC-K2 & TMC-K3: Mastic material, provided in each TMC-K Kit, is meant to fill and seal the NPT thread area of each Terminator Cable Fitting prior to Cold ShrinkTM Assembly installation. The mastic is provided in two forms: Two Cold ShrinkTM Assemblies are provided in these kits. The smaller of these (less than three inches long) serves as an adapter to increase the diameter range of the protective outer sleeve assembly. TMC-K1 through TMC-K6 ... Mastic Strips TMC-K7 through TMC-K10 .. Mastic Roll INSTALLATION: Figure (1.) Position Cold ShrinkTM Assembly @ (Figure 2) over cable jacket. Direct loose core pull tab onto cable first as shown. (TMC-K1, K2, K3) KETEXT CO? NOTE (TMC-K1, TMC-K2 & TMC-K3 Kits): Position smaller Cold ShrinkTM Assembly over the cable last as shown 2 (Figure 2). Luma Pull Tabs - (Figure InkACK3k Connection End INSTALLATION (Continued): (2.) Install TMC or TMCX Terminator Cable Fitting according to instructions provided. See typical example 3 (Figure 2). (4.) TMC-K1, TMC-K2, TMC-K3 Only: Position Cold ShrinkTM Adapter Assembly as shown 5 (Figure 4). Install by unwinding loose core pull tab in a counter-clockwise direction around cable. Figure 2 Figure 4 , :, . i . Junction Box, Cabinet, - Panelboard or Other Pull Tab (3.) Use mastic seal strips (or roll) from kit to fill gap over NPT threads of fitting (Figure 3). Remove white release liners before wrapping. Build mastic level to flats of fitting hex nut. Mastic material may be folded to ease wrapping. (5.) Position Cold ShrinkTM Corrosion Protection Assembly ® (Figure 5) over Terminator® Cable Fitting. Install by unwinding loose core pull tab in a counter-clockwise direction around cable. Rubber corrosion protection sleeve should make contact with enclosure wall during installation. Figure 3 NOTE: Plastic core is recyclable other : : Figure 5 Mastic Seal LE 22 XBxSYAW .. Pull Tab Enclosure Wall All statements, technical information and recommendations contained herein are based on information and tests we believe to be reliable. The accuracy or completeness thereof are not guaranteed. In accordance with Crouse-Hinds "Terms and Conditions of Sale", and since conditions of use are outside our control, the purchaser should determine the suitability of the product for his intended use and assumes all risk and liability whatsoever in connection therewith. COOPER Crouse-Hinds Cooper Industries Inc. Crouse Hinds Division PO Box 4999, Syracuse, New York 13221 • U.S.A Copyright 1997, Cooper Industries Inc. IF 1378 Revision 1 New 9/97 Quality from Coope Industrias Cold ShrinkTM is a Trademark of 3M 78-8120-1053-2


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply