Free English COOLER MASTER MASTERBOX NR600 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD COOLER MASTER MASTERBOX NR600 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What is included in the package contents of the COOLER MASTER MASTERBOX NR600?
The package for the COOLER MASTER MASTERBOX NR600 includes the following parts and quantities:
| Part Label | Description | Quantity |
|---|---|---|
| A | Nut Setter / Socket Tool | x1 |
| B | Screw (Hex Head) for Motherboard/PSU | x13 |
| C | SSD Mounting Screw/Pin | x20 |
| D | Rubber Grommet | x24 |
| E | Long Fan Screw | x4 |
| F | HDD Mounting Rail | x6 |
| G | Cable Tie | x10 |
| H | Magnetic Dust Filter | x1 |
| I | HDD Screw | x4 |
How do I remove the side panels on the COOLER MASTER MASTERBOX NR600?
To open the COOLER MASTER MASTERBOX NR600:
1. Locate the thumbscrews on the rear of the case securing the side panel.
2. Unscrew the thumbscrews.
3. Pull the panel outwards or slide it towards the rear to detach it from the chassis.
How do I install the motherboard in the COOLER MASTER MASTERBOX NR600?
1. Lay the case flat on its side.
2. Align the motherboard with the pre-installed standoffs inside the case.
3. Use the Nut Setter (Part A) if standoffs need adjustment.
4. Secure the motherboard using the provided screws (Part B) (Quantity: x13 provided in kit).
How do I install the power supply unit (PSU) in the COOLER MASTER MASTERBOX NR600?
1. Place the power supply unit into the bottom rear chamber of the case.
2. Align the PSU mounting holes with the holes on the rear of the chassis.
3. Secure the PSU using the Hex Head Screws (Part B).
How do I install an add-on card or GPU in the COOLER MASTER MASTERBOX NR600?
1. Identify the expansion slot corresponding to your motherboard’s PCIe slot.
2. Loosen the screw holding the expansion slot cover and remove the cover.
3. Insert the add-on card or graphics card into the motherboard slot.
4. Secure the card bracket to the chassis using the screw removed in step 2.
How do I install a 3.5″ Hard Disk Drive (HDD) using the rails in the COOLER MASTER MASTERBOX NR600?
1. Take two HDD Mounting Rails (Part F).
2. Snap the rails onto the sides of the 3.5″ hard drive. Ensure the pins on the rails insert into the drive’s screw holes.
3. Slide the drive with attached rails into the drive cage slots until it locks into position.
How do I mount a 3.5″ HDD on top of the drive cage in the COOLER MASTER MASTERBOX NR600?
1. Place the 3.5″ hard drive on top of the drive cage located at the bottom of the case.
2. Align the drive holes with the cage holes.
3. Secure the drive from underneath the cage top using the specific HDD Screws (Part I).
How do I install a 3.5″ HDD on the chassis wall of the COOLER MASTER MASTERBOX NR600?
1. Insert Rubber Grommets (Part D) into the designated mounting holes on the chassis wall.
2. Install mounting screws into the back of the 3.5″ HDD.
3. Align the screw heads with the grommets and slide the drive down to lock it into place.
How do I install a 2.5″ SSD in the COOLER MASTER MASTERBOX NR600?
1. Screw four SSD Mounting Pins (Part C) into the bottom of the 2.5″ SSD.
2. Insert four Rubber Grommets (Part D) into the corresponding mounting holes on the motherboard tray or the PSU shroud.
3. Press the SSD pins into the rubber grommets to secure the drive.
How do I install front fans in the COOLER MASTER MASTERBOX NR600?
1. Remove the front panel.
2. Align the 120mm or 140mm fans with the mounting slots on the front chassis.
3. Secure the fans using the Long Fan Screws (Part E) from the front or standard fan screws depending on the specific alignment and number of fans.
Where can I install radiators in the COOLER MASTER MASTERBOX NR600?
The COOLER MASTER MASTERBOX NR600 supports radiator installation in the following locations:
Front: Supports 120mm, 140mm, 240mm, 280mm, or 360mm radiators.
Top: Supports 120mm or 240mm radiators.
Rear: Supports a 120mm radiator.
How do I install the dust filters on the COOLER MASTER MASTERBOX NR600?
1. Place the magnetic dust filter (Part H) on the designated ventilated area on the side panel or top panel.
2. Ensure the filter covers the ventilation holes completely.
CLICK HERE TO DOWNLOAD COOLER MASTER MASTERBOX NR600 (01) PDF DOCUMENT