CLUB CAR TEMPO WALK (01) PDF Document

The CLUB CAR TEMPO WALK includes the following components: 1. Ultrasonic Sensors (3 qty) for Obstacle Detection. 2. Dual USB Charge Ports for charging cell phones. 3. 8 inch Tablet for Front, Center, and Back Yardages. 4. Dashboard for Power, Run, Neutral, and Battery Meter. 5. Cooler with Scorecard Clip. 6. Cup Holders for Divot Repair Seed and Beverages.

The following maintenance items are recommended for the CLUB CAR TEMPO WALK: – Motor Gear Lube: Valvoline Multi Purpose #2 Grade Lithium Complex. – Front Caster Grease: Valvoline Multi Purpose #2 Grade Lithium Complex. – Rear Tires: Max PSI 14, Kenda Turf Rider 13×6.5×6 Tubeless 2 ply. – Front Tire: Max PSI 22, Kenda Turf Rider 11×4.0x4 Tubeless 2 ply. – Fuse: 30 Amp, CC P/N 102492301. – Dashboard: GE Clear 100% Waterproof Silicone 2+.

1. Study and understand all controls. 2. Read safety and information decals located on the unit and view the tutorial video. 3. Securely fasten clubs in the CLUB CAR TEMPO WALK. 4. Make sure the front wheel is turned in the desired direction. 5. Turn the unit ON by pressing the power switch on the dashboard and ensure nothing is in your path and the unit is not in the neutral position. 6. Make sure the transmitter switch is OFF, then attach the transmitter securely and vertically on your waistband at the center of your back. Never use the transmitter in any other position. 7. When ready to activate, make sure you are in a safe operating environment. Once the transmitter is directly facing the unit, turn the transmitter switch to the ON position. Standing centered and directly in front of the unit approximately 2 to 3 feet, slowly begin to walk away from the unit until you hear a beep indicating that you are connected to the CLUB CAR TEMPO WALK.

1. After coming to a complete stop, turn off the transmitter to disconnect from the CLUB CAR TEMPO WALK. 2. Turn the unit power off by pressing the power switch on the dashboard. 3. Remove the transmitter from your waist and place it on the unit.

1. Make sure the transmitter is turned off. 2. Loosen the nut securing the toggle switch at the side of the transmitter case. 3. Remove the 2 screws on the front lid of the case. 4. Gently remove the transmitter case lid. 5. Channels are selected using the white rotary dial on the transmitter board. 6. Use a small flat head screwdriver and turn the dial so that the arrow points to the desired channel. 7. Make sure this channel matches the corresponding CLUB CAR TEMPO WALK unit channel. 8. Repeat steps 2 to 4 in reverse order to close and secure the transmitter case.

1. Power on the unit using the dashboard. 2. Press the neutral button steadily until you hear the voice audio Calibration Mode, continue to press the neutral button until you hear the audio Channel Select Mode. 3. At this point the battery meter LED lights will go away and illuminate only one light indicating the current channel of operations for the unit. 4. Push the neutral button until the LED light shows the desired channel. 5. Pause and wait to hear the chime indicating the channel is reset and then the battery meter will light up fully.

1. Always calibrate the CLUB CAR TEMPO WALK on a flat and level surface. 2. Place a tape measure extending straight from the front nose of the unit for 48 inches. Make sure the tape is centered on the unit. 3. Power on the unit and press the neutral button steadily until you hear the voice audio Calibration Mode. 4. Quickly move to straddle the measuring tape, with your heels at the 48 inch mark. Your back should be facing the unit and you must stand still during the calibration process. 5. The transmitter should be turned on and it should be centered on your waist in the middle of your back. 6. Wait for the unit to successfully complete its calibration, which will be signaled by several quick chimes. You must wait until these chimes end before you move. It is now okay to turn off the transmitter.

Once the necessary repairs have been made, follow these steps: Step 1: Turn on the CLUB CAR TEMPO WALK and wait for the start-up chime. Step 2: Wait for the audio about the disabled sensors. Step 3: Press the neutral button twice on the dashboard.

1. Power on the tablet. 2. Select the gear icon at the top right of the operating instructions screen and enter the password. 3. Select Location Setup from the left column, then type in the course name in the search box. 4. Select the desired course file that is displayed below the course search field and save. 5. Select the Exit tab from the left column when finished. 6. Press the Start button and select holes to confirm the tablet has been set up correctly.

1. Unclip the front plastic screen protector on the sides of the tablet. 2. Push back the rubber gasket around the tablet case edges. 3. Remove the tablet. 4. Plug the micro USB cable using the right orientation into the new tablet. 5. Slide the tablet into the case, with the charger side first. 6. Make sure that the tablet is charging. 7. Secure the rubber gasket around the tablet case edges. 8. Replace the plastic screen protector.

1. The CLUB CAR TEMPO WALK must be fully charged before storing. 2. Turn off the unit power. 3. The main circuit breaker under the cooler must be disconnected for winter storage. 4. Remove the tablet from the unit, power it off, and store indoors. 5. The unit should not be connected to the charger during long term storage. 6. The unit must be recharged within 6 months to maintain battery integrity. 7. Store in a dry, clean, well ventilated area, between 0 and 45 degrees Celsius. 8. Adjust tires to recommended tire pressure. 9. Perform annual periodic lubrication as necessary. 10. Thoroughly clean the unit.

1. Connect the unit to the charger and recharge overnight. 2. When the unit is charged, reconnect the main circuit breaker located under the cooler. 3. Reattach the fully charged tablet to its charging cable, then attach it to the unit, and power the tablet on. 4. Power on the CLUB CAR TEMPO WALK in a safe, open area to test performance. 5. Adjust tires to recommended tire pressure. 6. Perform the Pre-Operation and Daily Safety Checklist and Performance Inspection.

For the Front Wheel/Caster, use Valvoline Multi-Purpose #2 Grade Lithium Complex every 200 hours of operation or 100 rounds of golf. For the Motor Gear Box Grease Fitting, use Valvoline Multi-Purpose #2 Grade Lithium Complex every 200 hours of operation or 100 rounds of golf.