FREE ENGLISH CIRRUS CR9100 (01) PDF USER GUIDE
FREE ENGLISH CIRRUS CR9100 (01) PDF USER MANUAL
FREE ENGLISH CIRRUS CR9100 (01) PDF OWNER GUIDE
FREE ENGLISH CIRRUS CR9100 (01) PDF OWNER MANUAL
FREE ENGLISH CIRRUS CR9100 (01) PDF REFERENCE GUIDE
FREE ENGLISH CIRRUS CR9100 (01) PDF INSTRUCTION GUIDE
FREE ENGLISH CIRRUS CR9100 (01) PDF REFERENCE MANUAL
FREE ENGLISH CIRRUS CR9100 (01) PDF INSTRUCTION MANUAL
FREE ENGLISH CIRRUS CR9100 (01) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD CIRRUS CR9100 (01) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
CIRRUS CR9100 (01) PDF SUMMARY:
What basic safety precautions should be followed when using the Vacuum Cleaner?
When using your Vacuum Cleaner, basic precautions should always be followed, including the following: Before connecting the power cord of your new Vacuum Cleaner to an electrical outlet, check the voltage rating. Your power source should correspond with the voltage rating plate on the underside of the vacuum cleaner. Use only household alternate current outlets. Never use direct current power sources. If you are unsure of the voltage supply in your area, consult a qualified electrician. Connecting the vacuum cleaner to a higher voltage than indicated in these instructions may result in damage to the vacuum cleaner and/or personal injury. Do not leave the vacuum cleaner while plugged in. Unplug from the outlet when not in use, and before servicing. Do not use outdoors or on wet surfaces. Do not allow the vacuum cleaner to be used as a toy. Pay close attention when using by or near children. Use only as described in this manual. Use only manufacturer’s recommended attachments. Do not use the vacuum cleaner if the cord or plug is damaged. If the vacuum cleaner is not working as it should, has been dropped, damaged, left outdoors or immersed in water, return it to an authorized Vacuum Cleaner dealer. Do not pull or carry by the cord, use the cord as a handle, run appliance over cord, close a door on the cord, or pull the cord around sharp edges or corners. Keep the cord away from heated surfaces. Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord. Do not handle the plug or the vacuum cleaner with wet hands. Do not put objects into the openings. Do not use with any openings blocked. Keep free of dust, lint, hair and anything that may reduce air flow. Do not allow loose clothing, hair, fingers or other parts of the body to come into contact with any openings or moving parts of the vacuum cleaner. Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes. Do not use without the dust bag and/or filters in place. Always turn off all controls before unplugging the vacuum cleaner, or before connecting or disconnecting either the hose or the agitating brush. Do not use the vacuum cleaner to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present, as this could impair the electrical safety of the vacuum cleaner. Floor attachments and accessories must not be used at head level to avoid the risk of injury to eyes and ears. Do not touch the agitating brush when in use. Vacuum Cleaner dustbags are disposable and are intended to be used only once. Do not attempt to reuse them. Do not use the vacuum cleaner on people or on animals.
What should you check before connecting the power cord of the Vacuum Cleaner to an electrical outlet?
Before connecting the power cord of your new Vacuum Cleaner to an electrical outlet, check the voltage rating. Your power source should correspond with the voltage rating plate on the underside of the vacuum cleaner.
What type of power outlets should be used with the Vacuum Cleaner?
Use only household alternate current outlets. Never use direct current power sources.
What should you do if you are unsure of the voltage supply in your area?
If you are unsure of the voltage supply in your area, consult a qualified electrician.
What can happen if you connect the vacuum cleaner to a higher voltage than indicated in the instructions?
Connecting the vacuum cleaner to a higher voltage than indicated in these instructions may result in damage to the vacuum cleaner and/or personal injury.
What should you do when the vacuum cleaner is not in use or before servicing?
Unplug from the outlet when not in use, and before servicing.
Where should you not use the vacuum cleaner?
Do not use outdoors or on wet surfaces.
What should you do if the vacuum cleaner is not working as it should, has been dropped, damaged, left outdoors or immersed in water?
Return it to an authorized Vacuum Cleaner dealer.
How should you handle the vacuum cleaner cord?
Do not pull or carry by the cord, use the cord as a handle, run appliance over cord, close a door on the cord, or pull the cord around sharp edges or corners. Keep the cord away from heated surfaces.
How should you unplug the vacuum cleaner?
To unplug, grasp the plug, not the cord.
What should you not handle with wet hands?
Do not handle the plug or the vacuum cleaner with wet hands.
What should you not put into the openings of the vacuum cleaner?
Do not put objects into the openings.
What should you keep the vacuum cleaner free of?
Keep free of dust, lint, hair and anything that may reduce air flow.
What should you not allow to come into contact with the openings or moving parts of the vacuum cleaner?
Do not allow loose clothing, hair, fingers or other parts of the body to come into contact with any openings or moving parts of the vacuum cleaner.
What should you not vacuum?
Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
When should you not use the vacuum cleaner?
Do not use without the dust bag and/or filters in place.
What should you always do before unplugging the vacuum cleaner, or before connecting or disconnecting either the hose or the agitating brush?
Always turn off all controls before unplugging the vacuum cleaner, or before connecting or disconnecting either the hose or the agitating brush.
What should you not use the vacuum cleaner to pick up?
Do not use the vacuum cleaner to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
Where should floor attachments and accessories not be used?
Floor attachments and accessories must not be used at head level to avoid the risk of injury to eyes and ears.
What should you not touch when in use?
Do not touch the agitating brush when in use.
Are Vacuum Cleaner dustbags reusable?
Vacuum Cleaner dustbags are disposable and are intended to be used only once. Do not attempt to reuse them.
Should you use the vacuum cleaner on people or animals?
Do not use the vacuum cleaner on people or on animals.
What is the nominal voltage circuit for this appliance?
This appliance is for use on a nominal 120-volt circuit.
What type of plug does the appliance have?
The appliance has a grounding attachment plug.
Where should the appliance be connected to?
Make sure that the appliance is connected to an outlet having the same configuration as the plug.
Should an adapter be used with this appliance?
No adapter should be used with this appliance.
What does grounding provide for the appliance?
If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock.
What should you do if you are in doubt as to whether the outlet is properly grounded?
Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded.
What should you do if the plug does not fit the outlet?
If it can not fit the outlet, have a proper outlet installed by a qualified electrician.
How do you attach the handle?
- Remove handle screw.
- Insert handle into top of dust cover with handle switch facing forward.
- Align small hole on handle with screw hole in dust cover. Insert screw and tighten securely.
How do you store the cord?
Turn cord storage hook to upright position and wind cord between upper and lower hooks to store.
How do you quick-release the cord?
To quick-release cord: simply rotate hook downward and cord will drop for immediate use.
How do you replace the dust bag?
- Push down on knob at top of dust cover to open compartment.
- Pull cardboard bag collar off holder. Remove and discard used dust bag.
- Slide clean replacement bag collar onto holder.
- Close dust cover by reinserting tab on lower edge into groove on housing and snap shut.
When should you check the secondary filter?
Check for accumulated dust and dirt when replacing dust bag.
How do you replace the secondary filter for Model CR9100 & CR9I00A?
- Release the right tab on underside of bag supporter.
- Lift and rotate bag supporter to remove.
- Remove secondary filter from bottom of dust compartment.
- Replace secondary filter with new filter.
- Reinstall bag supporter.
When should you change the exhaust filter for Model CR8100?
Change the exhaust filter with every third dust bag replacement, or as needed.
How do you change the exhaust filter for Model CR8100?
- Depress handle release pedal to drop vacuum cleaner to low position.
- Push knob at side of exhaust filter cover to remove.
- Remove soiled filter and replace with new one.
How do you change the exhaust filter for Model CR9100 & CR9100A?
- Push the top latch on the exhaust filter cover to the right. Slide the cover upwards.
- Remove the soiled filter and replace it with a new one.
- Reinstall exhaust filter cover and push the top latch to the left.
How do you start the Vacuum Cleaner for Models CR8100, CR9100 & CR9100A?
Push the switch down to start. Push down O to stop.
How does the carpet nozzle height adjust?
The carpet nozzle height self adjusts instantly and automatically. Your vacuum will float evenly over varying carpet pile heights.
What are the three positions for the handle?
The handle of this vacuum cleaner can be set to any of three positions: Upright, Middle or Low.
How do you release the handle?
To release the handle, step on the pedal at the left rear corner of the vacuum cleaner.
When should the handle be in the Upright position?
Handle locks in this position for vacuum cleaner storage. The handle should always be in the upright position when cleaning tools are used.
What is the Middle position for?
This position is for normal cleaning. While in the middle position, the front of the nozzle can be raised by lowering the handle in order to cross room thresholds.
What is the Low position for?
This position is used for cleaning under most furniture.
How do you use the on-board cleaning tools for Model CR9100 & CR9100A?
- Remove hose cuff from nozzle inlet.
- Connect hose cuff to telescopic wand. Unlock wand collar to extend wand to desired length.
- Attach selected cleaning tool to wand.
(Tools may also be attached directly to flexible hose cuff, omitting extension wand). 4. Cleaning tools are stored conveniently on the back of the vacuum cleaner body. Snap tools back into their appropriate places.
What does the deluxe attachment set available for models without on-board tools contain?
- hose assembly
- curved wand
- 3-piece telescopic wand
- dusting brush
- crevice tool
- upholstery brush
What does the optional attachment package available for models equipped with on-board tools contain?
- hose assembly
- curved wand
How do you connect the optional hose assembly?
- Lift the lid of the cleaning attachment opening located at the back of your Vacuum Cleaner.
- Insert the hose end until it fits snugly.
How do you connect the tools?
- Connect any of the cleaning tools to the extension wand or curved wand and twist for secure fit.
- Twist and pull apart to remove.
How do you control the suction?
To reduce suction when cleaning draperies, small rugs etc., move the suction control slide on the back of the vacuum cleaner by increasing the opening until desired suction power is achieved. Close for normal vacuum operation.
How do you remove the bottom plate?
- Unplug the vacuum cleaner from the electrical outlet before servicing.
- Use handle release pedal to place vacuum in low position.
- Turn vacuum over to expose underside.
- Slide the two latches inward to release bottom plate.
- Slide bottom plate toward front of vacuum.
How do you reset the Thermal Switch for Models CR8100, CR9100 & CR9100A?
- Set power switch to the off position.
- Unplug the power cord.
- Wait about 10 min. to let the motor cool down.
- Push the reset button lightly to the stop position.
- Plug in the power cord.
- Set power switch to the on position.
How do you replace the drive belt?
- Unplug the power cord.
- Turn the unit over and remove the bottom plate.
- Lift the rear belt cover up and back.
- Remove the vented support fitting, noting position.
- Remove agitator unit and worn out belt.
- Loop new belt around motor drive shaft and agitator pulley.
- Replace agitator unit in housing.
- Turn agitator unit by hand to install new belt onto guide, making sure belt is not twisted and rotating parts move smoothly.
- Reinsert the vented support fitting and lower rear belt cover.
- Reinsert bottom plate making certain that the hinges are in place on the front of the housing before sliding the two latches outward to fasten.
When should you replace the agitator brushes?
Replace agitator brushes when they are worn or when the bristles do not touch a card held across the base plate.
How do you change the agitator brushes?
- Remove agitator, start as described on page 13 Section 1 to 5.
- Remove rubber end cover.
- Unscrew the end cap and remove.
- Remove the agitator shaft.
- Remove and replace the brushes on the shaft.
- Reinstall the pulley and agitator holder making sure they are inserted completely and firmly.
- Reinstall remaining parts.
- Reinstall agitator assembly as described previously in Step 6 to 10 on page 13.
What should you keep clean for best performance?
Keep machine and all accessories clean and in proper operating condition.
How do you maintain optimum cleaning efficiency?
Change dust bags and filters as recommended.
What should you always use?
Always use genuine dust bags and filters.
Who should you have your vacuum cleaner checked by regularly?
Have your vacuum cleaner checked regularly by your Authorized Vacuum Cleaner Dealer.
What kind of parts or services should you use?
Use only repair parts or services provided by Authorized Vacuum Cleaner Dealers.
Where should you store the machine?
Carefully store machine in a dry area.
How do you maintain optimum cleaning performance and safety?
Follow the Owner’s Manual.
How do you clean the nozzle for Model CR8100 if it is clogged?
- Unplug the power cord.
- Lift up the lid of cleaning attachment opening. Remove the clog or blockage.
- If the previous step does not correct the problem, pull the power nozzle from the cleaning attachment opening located at the base of the vacuum cleaner.
- Turn the unit over and remove the bottom plate.
- Unscrew the hose inlet fitting screw, then pull out the entire nozzle hose from the housing.
- Clear the obstruction from the hose assembly, replace the hose in the housing and reinstall the bottom plate.
How do you clean the nozzle for Model CR9100 & CR9100A if it is clogged?
- Unplug the power cord.
- Open the lid on the cleaning attachment opening, and remove clog or blockage.
- If the hose is still blocked, remove hose cuff from nozzle inlet.
- Turn the unit over, remove bottom plate.
- Check nozzle inlet tube for obstructions.
- When clear, reinstall bottom plate.
What does the limited warranty cover?
Cirrus Vacuum warrants that your Cirrus commercial vacuum cleaner, for a period of one year from your date of purchase, will be free from defects in material and workmanship for normal use in accordance with the Owner’s Manual. This limited warranty is granted only to the original purchaser.
What does the limited warranty not cover?
- Expenses related to pick up, delivery or house calls for warranty service.
- Parts of the cleaner that require replacement under normal use, such as disposable dust bags, filters, drive belts, light bulbs, and brushroll bristles.
- Damages or malfunctions caused by accident, acts of God, negligence, abuse, or use not in accordance with the Owner’s Manual.
- Defects or damages caused by improper service or maintenance, the use of parts other than genuine ProGrade parts or modifications made to the cleaner without our prior written approval.
- Damage that occurs during shipment.
- Vacuums purchased outside the United States.
- Vacuums subjected to rental use.
What will Cirrus do under the limited warranty?
Cirrus will, at its option, repair or replace a defective vacuum or vacuum cleaner part that is covered by this limited warranty. As a matter of warranty policy, Cirrus Vacuum will not refund the customer’s purchase price.
How do you register for warranty?
To register for warranty please visit our website at http://www.cirrus.com and fill out a registration card.
How do you obtain warranty service?
To obtain warranty service you must return the defective vacuum or vacuum cleaner part along with proof of purchase to any Cirrus Authorized Warranty Station.
How do you locate the closest Cirrus Authorized Warranty Station?
For the location of the closest Cirrus Authorized Warranty Station or for service information, call 216-524-4141 or email info@Cirrusvacuum.com.
Where can you write to for warranty information?
You can write to: Cirrus Vacuum Attn: Cirrus Warranty 1933 Highland Road Twinsburg, Ohio 44087.
Who pays for shipping if it is necessary to ship the cleaner outside your community to obtain warranty repair?
You must pay the shipping charges.
What should you include when returning parts for repair?
When returning parts for repair, please include the model, type, and serial number from the data plate on the vacuum cleaner.
CLICK HERE TO DOWNLOAD CIRRUS CR9100 (01) PDF MANUAL
How do adjust carpet level there is no switch?
As per page 5 & 6, you don’t, It’s a “self-adjusting nozzle”.