CHEVROLET TRAX 2026 (01) PDF Document

To remove the key, press the button on the side of the remote key and pull the key out. Never pull the key out without pressing the button.

To start the engine remotely:

Step 1. Press and release the lock button on the remote key.

Step 2. Immediately after completing Step 1, press and hold the remote start button for at least four seconds. If the vehicle’s lights cannot be seen, press and hold the remote start button for at least four seconds.

To extend the engine run time by 15 minutes, repeat the remote start steps while the engine is still running. An extension can be requested 30 seconds after starting. The engine run time can only be extended if it is the first remote start since the vehicle has been driven, and it can only be extended one time.

To manually shut off a remote start, you can do one of the following:

1. Press and hold the remote start button until the lights turn off.

2. Turn on the hazard warning flashers.

3. Turn the ignition switch on and then off.

To lock/unlock the doors from the inside:

1. Press the lock or unlock button on the power door lock switch.

2. Push down on the door lock knob to lock a door.

3. Pull the door handle once to unlock it. Pull the door handle again to unlatch it.

To adjust a manual seat:

Step 1. Pull the handle at the front of the seat.

Step 2. Slide the seat to the desired position and release the handle.

Step 3. Try to move the seat back and forth to be sure it is locked in place.

To fold the seatback:

Step 1. Pull the lever on top of the seatback to unlock the seatback. A red indicator near the seatback lever is exposed when the seatback is unlocked.

Step 2. Fold the seatback down.

Step 3. Place the outboard seat belt in the seat belt clip on the side trim of the vehicle.

To adjust the steering wheel:

Step 1. Pull the lever down.

Step 2. Move the steering wheel up, down, forward, and backward.

Step 3. Pull the lever up to lock the steering wheel in place.

Pull the windshield wiper lever toward you to spray windshield washer fluid and activate the windshield wipers. The wipers will continue until the lever is released or the maximum wash time is reached.

Set the time and date using the infotainment system. See the “Date/Time” section under Settings (11 Inch Screen Radio) or Settings (8 Inch Screen Radio) in your manual.

To reset the engine oil life system for the Base Cluster:

Step 1. Display the REMAINING OIL LIFE on the Driver Information Center (DIC).

Step 2. Press and hold the set/clear menu item button (check mark symbol) while the Oil Life display is active. The oil life will change to 100%.

To reset the engine oil life system for the Uplevel Cluster:

Step 1. Place the vehicle in P (Park).

Step 2. From the infotainment home screen, select Vehicle Status > Maintenance > Oil Life > Reset.

Step 3. Follow the menu and select Reset on the display screen. Then select Reset to confirm the reset. The percentage will change to 100%.

Use full synthetic engine oils that meet the dexos1 specification. Use SAE 0W-20 viscosity grade engine oil.

If the overheat warning is displayed with no sign of steam:

Step 1. Turn the air conditioning off.

Step 2. Turn the heater on to the highest temperature and to the highest fan speed. Open the windows as necessary.

Step 3. When it is safe to do so, pull off the road, shift to P (Park) or N (Neutral) for an automatic transmission and let the engine idle.

If the overheat warning no longer displays, the vehicle can be driven. Continue to drive the vehicle slowly for about 10 minutes. Keep a safe vehicle distance from the vehicle in front.

To safely change a flat tire:

Step 1. Set the parking brake firmly.

Step 2. Put the vehicle in P (Park).

Step 3. Turn the vehicle off and do not restart the vehicle while it is raised.

Step 4. Do not allow passengers to remain in the vehicle.

Step 5. Place wheel blocks, if equipped, on both sides of the tire at the opposite corner of the tire being changed.