Free English CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How do I start using the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50?
To start using the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50, you must first press and hold the power button on the back of the computer for 2 seconds. When powering on for the first time, you are required to perform the initial setup including formatting, selecting the speed unit, pairing sensors if applicable, selecting the time zone, and setting the clock display format.
How do I charge the battery of the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50?
To charge the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50, follow these steps:
Step 1. Set the computer into the cradle.
Step 2. Insert the USB plug into your computer or a commercial USB battery charger.
Step 3. Once charging starts, the battery icon will display animation. When the icon shows a solid light, charging is completed. The standard charging time is approximately 5 hours.
Cautions: Do not charge the computer if it is wet. Charging will not occur if the connected computer is in sleep state.
What are the precautions for using the battery of the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50?
Follow these instructions to maintain the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50 battery performance:
1. Charge at ambient temperatures between 41F to 104F (5C to 40C).
2. Unplug the USB after charging is finished.
3. Do not apply vibration during charging.
4. Avoid charging, discharging, or storing at high temperatures, such as inside a car or near a heater, as this will damage the battery.
5. For long periods of storage, do not store the unit after a full charge. Charge the unit for 10 minutes every 6 months.
How do I install the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50 bracket?
The CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50 uses a FlexTight bracket that can be attached to the stem or handlebar. Place the bracket band and rubber pad around the stem or handlebar, insert the bracket into the band, and tighten the dial by hand. Do not use tools to tighten the dial as it may damage the screw thread. Ensure the bracket is mounted firmly and check periodically that it has not loosened.
How does the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50 measure speed?
The CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50 can calculate speed using the GPS signal or by receiving signals from an optional ANT+ speed sensor. If both are available, priority is given to the ANT+ sensor signal for more accurate, rotation-based measurement. If the GPS signal cannot be received, the unit may stop measuring or display less accurate results unless an ANT+ speed sensor is being used.
How do I perform sensor pairing with the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50?
To register an ANT+ sensor to your CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50, follow these steps during the setting mode:
1. Use the menu button to select the desired sensor type: SP (Speed), ISC (Speed/cadence), CD (Cadence), HR (Heart rate), or PW (Power).
2. Hold the MODE button to begin the search.
3. Send a signal from your sensor according to its specific method (e.g., rotating the wheel for speed sensors, or wearing the strap for heart rate sensors).
4. Once the computer finds the signal, the sensor ID is registered.
What is the difference between automatic and manual pairing for the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50?
The CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50 offers two methods for pairing:
Automatic search: The computer automatically detects and pairs with the sensor by receiving its signal. This is the standard method.
Manual ID number entry: You enter the specific ID number of the sensor. This method is useful if there are multiple sensors nearby and you want to ensure the computer pairs with the specific one you want.
How do I reset the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50?
To reset the measurement data on your CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50, press and hold the MODE button while the measurement screen is displayed. All measurement data up to that point will be finalized as trip data.
Why does the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50 display “MEM FULL”?
The “MEM FULL” message flashes on the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50 when the internal storage capacity has been reached. You must upload your trip data to your computer to free up space before new data can be recorded.
What is the Restarting operation for the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50?
If the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50 operates incorrectly or displays errors, you can perform a restarting operation. Press the AC button on the back of the computer. All screen items will light up for 2 seconds, and the unit will return to the GPS search screen. Note that this action deletes any records currently under measurement.
How do I calibrate the power sensor on the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50?
To calibrate the power sensor with your CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50:
1. Stop measurement on the measurement screen.
2. Press and hold the MENU button for 4 seconds.
3. “CALIB” will flash on the display as calibration begins.
4. After 3 seconds, calibration is complete and the unit returns to the measurement screen. Ensure no load is applied to the sensor/crank during this process.
What icons appear on the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50 display?
| Icon | Description |
|---|---|
| Battery | Displays remaining battery in 5 levels. |
| Sensor signal | Flashes when ANT+ sensor signal is received. |
| Pace arrow | Indicates if speed is faster (up) or slower (down) than average. |
| GPS | Indicates GPS signal status. |
| Speed unit | Flashes during measurement. |
| Tire circumference | Lights up when circumference is entered. |
| Clock | Lights up when clock is displayed. |
How do I change settings on the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50 alone?
You can change configuration settings for the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50 without a computer by pressing the MENU button from the measurement screen. This allows you to access various menu options. Once settings are changed, press the MENU button to register the changes. If you leave the menu screen idle for 1 minute, it will automatically return to the measurement screen.
What factors affect GPS signal reception on the CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50?
The CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50 may have difficulty receiving a GPS signal in the following situations:
1. In tunnels, underground, or inside buildings.
2. Between high-rise buildings, or under elevated structures/arcades.
3. During bad weather, such as heavy rain or snow.
4. Near high-voltage power lines or mobile phone relay stations.
5. If the computer display is not facing toward the sky.
CLICK HERE TO DOWNLOAD CATEYE STEALTH 50 CYCLOCOMPUTER CC-GL50 (01) PDF DOCUMENT