BROUK SP0592 (01) PDF Document

The BROUK SP0592 power bank includes the following components as identified in the product overview:

1. 5V Input Port (Micro USB)

2. 5V Input/Output Port (TYPE-C)

3. 5V Output Port (USB A-type)

4. ON/OFF button

5. 5V Output port (USB A-type)

6. LED indicator

The LED indicator on your BROUK SP0592 advises of the remaining charge. The number of illuminated lights decreases as the power supply dwindles.

1 LED: 0-25% Charged

2 LEDs: 25-50% Charged

3 LEDs: 50-85% Charged

4 LEDs: 85-100% Charged

The status of the power bank is also indicated by the LEDs as follows:

You can charge the BROUK SP0592 power bank using one of two methods:

a. Using your mobile phone’s USB adapter:

Connect a USB or TYPE-C cable to your phone’s USB adapter. Using the micro USB connector or TYPE-C connector, connect the other end of the cable to the IN port on the portable power bank. Plug the USB adapter into the outlet to begin charging.

b. Using your computer:

Connect a USB or TYPE-C cable to a USB outlet on your computer. Using the micro USB or TYPE-C connector, connect the other end of the cable to an IN port on the portable power bank. Make sure the computer is on to begin charging.

Note: Please don’t charge the power bank with USB and TYPE-C at the same time.

1. The portable power device has a USB and TYPE-C output port with a maximum output current of 2100 mA.

2. Connect a USB or TYPE-C cable to your mobile phone/device using the appropriate connector. Connect the other end of the USB or TYPE-C cable to the OUT port of the portable power bank. Your mobile phone/device should display the status of charging.

3. Remove the USB or TYPE-C cable from your mobile device when it is fully charged.

Note: In order to charge a device, use only the accessory cable provided with the power bank or the cable included with your own device by its manufacturer. The adapter and mobile phones must support TYPE-C when you use the TYPE-C function.

When using this product, basic precautions should always be followed, including the following:

1. Read all the instructions before using the product.

2. The power bank contains an internal lithium-ion battery. Upon initial use or after a prolonged storage period, fully charge it once. The unit’s full performance is achieved only after 2 or 3 completed charge and discharge cycles.

3. Power banks are not allowed in checked luggage on commercial airline flights. Handle with care and dispose of in accordance to local regulations. Carry-on only.

4. To reduce the risk of injury, close supervision is necessary when the product is used near children.

5. Do not put fingers or hands into the product.

6. Do not expose power bank to rain or snow.

7. Use of a power supply or charger not recommended or sold by the power pack manufacturer may result in a risk of fire or injury to persons.

8. Do not use the power bank in excess of its output rating. Overload outputs above rating may result in a risk of fire or injury to persons.

9. Do not use the power bank that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.

10. Do not disassemble the power bank. Take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or injury to persons.

11. Do not expose a power pack to fire or excessive temperature. Never store or use this product in temperatures below 32°F (0°C) or above 113°F (45°C).

12. Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.

13. Do not charge the power bank while using the power bank to charge a device. Do not charge the power bank for more than 10 hours and do not leave unattended.

14. Disconnect the power bank when not in use.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.