BRITA FF-100 (01) PDF Document

The components shown in the Front View are the Replaceable Filter Cartridge, Insert Groove, Base System, Packet with 2 Faucet Adapters and Washers, Filter Cup, Strainer, Mounting Collar, Filter Handle, Filter Replacement Indicator, and Aerator. The Back View shows the Filter Cartridge Release Button.

If any parts are missing, or to locate retailers, please call BRITA Consumer Services at 1-800-24-BRITA (U.S.) or 1-800-387-6940 (Canada).

This product contains a nonreplaceable, sealed battery. The batteries and electronics are sealed in a waterproof compartment inside your BRITA Faucet Filtration System and do not come into contact with water. The Filter Replacement Indicator is designed to last for the life of your BRITA Faucet Filtration System (about 5 years, depending on usage).

STEP 1: Remove aerator from faucet. Unscrew (clockwise) the aerator and remove any original rubber washers from your faucet. If difficult to remove, use a dry towel to grip the aerator. Clean off any scale or rust buildup.

If your faucet has threads on the outside, you most likely will not need to use an adapter. Attempt to attach the system directly to your faucet. If it does not fit, call Brita Consumer Services at 1-800-24-BRITA (U.S.) or 1-800-387-6940 (Canada). Proceed to Step 3.

If your faucet has threads on the inside, you will need to use one of the adapters and corresponding washers provided. Select the proper adapter and washer that fit onto your faucet. If neither adapter fits, please call Brita Consumer Services at 1-800-24-BRITA (U.S.) or 1-800-387-6940 (Canada). Place the washer into the recessed end of the adapter. Twist the adapter (counterclockwise) onto your faucet and tighten by hand until snug. If difficult to tighten, insert a coin into the notch in the bottom of the adapter and twist until snug. Caution: Using pliers to tighten the adapter may damage the threading.

NOTE: The Brita Faucet Filtration System cannot be attached to faucets with a built-in spray feature at the end of the faucet.

STEP 3: Attach the base system to your faucet. Position the base system so that the filter cup is on the left side of your faucet and the Filter Replacement Indicator is facing you. Twist the mounting collar onto the faucet and tighten by hand until snug. Do not tighten with pliers. Do not over-tighten.

If you are having difficulty, rotate the base system backward and forward while further tightening the mounting collar.

STEP 4: Insert filter cartridge into filter cup. Support the bottom of the filter system with one hand. Align the insert groove on the lower part of the cartridge with the Filter Replacement Indicator at the front of the filter cup. Insert the filter cartridge into the filter cup until a “click” is heard. Do not force the filter cartridge into the system base. Inserting the new filter cartridge automatically resets and activates the electronic Filter Replacement Indicator. A green signal will flash, indicating that the filter is engaged.

STEP 5: Flush the new filter cartridge with water. Move the filter handle toward you to the filtered Brita water setting: BRITA. Turn on the faucet to flush the new filter for 5 minutes to remove any carbon dust and activate the filter. It is normal for carbon dust to appear. The 100 gallon/378 liter filter life begins after the 5-minute conditioning period.

NOTE: Use with cold water only. Do not run hot water (above 100°F/38°C) through the filter, as it may damage the filter.

By adjusting the handle to the following positions, you can select the water you want:

The filter status based on the indicator light when switched to the filtered Brita water setting is:

Replacing the filter cartridge is easy. If the Filter Replacement Indicator flashes red when you switch to the filtered Brita water setting, it is time to replace the filter cartridge. Prompt filter replacement assures you of healthier, great-tasting water.

To remove the old cartridge, turn water off, press the filter cartridge release button located at the back of the filter cup and pull cartridge up to remove it. To insert a new cartridge, follow the directions in Step 4.

NOTE: If the filter is removed for cleaning purposes (e.g., for rinsing or wiping off) while in green mode, please insert filter back into unit within 30 seconds to make sure the counter is not reset. However, once the Filter Replacement Indicator has begun to show a red light (indicating the Replacement Period), do not remove the cartridge unless you intend to replace it. Once the filter has entered the Replacement Warning Period, inserting a cartridge will automatically reset the Filter Replacement Indicator.

If, for any reason, you need to replace your filter early (before the red flashing signal from the indicator), remove the old cartridge (see directions on Replacing Filter Cartridge) and prepare to insert a new one (Step 4).

To manually reset the indicator for your new cartridge, wait at least 30 seconds after the old filter has been removed before inserting the new one. This allows the counter to reset properly.

For optimal use, care and safety:

The BRITA Faucet Filtration System is not intended to purify water. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts. Individuals requiring water of special microbiological purity should follow the advice of their doctor or local health officials regarding the use and consumption of their tap water and Brita water.

The system and installation must comply with state and local laws and regulations.

Use with cold water only. Do not run hot water (above 100°F/38°C) through the filter, as it may damage the filter.

Do not push filter cartridge release button while filtering water.

Prior to each use, let water run through the filter for five seconds to activate the filter. If the filter has not been used for a few days, let the water run for 30 seconds before use.

For optimal system performance and highest-quality filtered water, promptly replace the filter cartridge when signaled by the Filter Replacement Indicator.

Clean the exterior of the BRITA Faucet Filtration System with a damp sponge or soft cloth. A mild dishwashing liquid may be used. Do not use abrasive cleaners or scouring pads to clean this product. DO NOT put any parts of this product in the dishwasher.

Only draw filtered water from filter port. All other water is unfiltered.

Do not use the BRITA Faucet Filtration System if incoming tap water exceeds 170°F/77°C. Very hot water will damage the system. (While most of the newer hot water heaters are preset to 120°F/49°C, temperatures vary from household to household. If you suspect your water temperature may be higher than 170°F/77°C, check the setting on your water heater.)

See Step 2 of Installation in Five Easy Steps to determine if you need to use an adapter. Check to see that you have correctly inserted the proper adapter and washer.

Call Brita Consumer Services at 1-800-24-BRITA (U.S.) or 1-800-387-6940 (Canada).

Check to see that you placed the washer between the faucet and the adapter. Check to see that the mounting collar is tight and the threading is aligned with the faucet or adapter threading. Only water from filter port is filtered. All other water is unfiltered.

Make sure the filter cartridge is locked into place. Water leaking or spraying from system may not be filtered. Only water from filter port is filtered. All other water is unfiltered.

Remove the system from the faucet and clean the sediment from the strainer in the mounting collar. If flow rate of filtered water remains slow, replace filter cartridge. Although Brita Faucet Replacement Filters have an extra layer to reduce sediment buildup, very high sediment in your water may cause the system to prematurely clog before the typical end of filter life. The clogging means that your Brita Faucet Replacement Filter is removing the sediment from your tap water. See directions for Early filter replacement and manual reset of the Filter Replacement Indicator.

Make sure the filter cartridge is locked into place. If you replaced the cartridge before the indicator light flashed red, you need to manually reset the Filter Replacement Indicator. See directions for Early filter replacement and manual reset of the filter replacement indicator.

Call Brita Consumer Services at 1-800-24-BRITA (U.S.) or 1-800-387-6940 (Canada).

The capacity is 100 gallons (378 liters) and the Service Flow Rate is 0.58 gpm (2.19 L/min).

The working pressures are 20 psig/100 psig (138 kPa/689 kPa) (1.4 kg/cm²/7.0 kg/cm²). The Filtered Water Temperature range is 34°F/100°F (1°C/38°C).